共查询到17条相似文献,搜索用时 334 毫秒
1.
比较完整地阐述端面谐波齿轮传动的啮合分析理论,编制端面谐波齿轮传动的啮合分析计算程序,并确定相应的啮合参数和结构参数的自动设计方法。这些理论和方法对端面谐波齿轮传动的开发和研制有重要的参考价值。 相似文献
2.
3.
4.
本文对端面谐波齿轮传动的啮合分析理论和应力分析方法等进行了较深入研究,并在此基础上应用计算机技术编制了端面谐波齿轮传动计算机辅助设计(DMCAD)的软件系统。通过应用该软件系统对端面谐波齿轮传动啮合性能和应力状态等进行电算分析,获得了一些对研制开发端面谐波齿轮传动有参考价值的数据和结论。 相似文献
5.
端面谐波齿轮传动较径向谐波齿轮传动有不同的特点,它是在轴向变形力的作用下迫使端面齿柔轮变形使其与端面齿刚轮啮合并产生相对运动。对端面谐波齿轮传动来说,啮入深度、齿侧间隙等是分析和评价其啮合性能的质量指标,而齿形角、柔轮的变形规律和变形量的大小,又是影响啮入深度和齿侧间隙的主要因素。为此本文利用已建立的啮合分析计算方法,通过计算机绘出的图形,着重分析齿形角、最大变形量等对啮入深度和齿侧间隙的影响,并从中获得了一些有实用价值的结论,从而为端面谐波齿轮传动选取合理的啮合参数和结构参数提供了依据。 相似文献
6.
7.
建立的端面谐波齿轮传动的啮合分析软件,可以较快地选取最佳传动方案,确定相应的啮合参数和结构参数。在介绍了该软件的总体结构后,进一步阐明了该软件中人机对话设计方法和啮合性能分析方法的设计思想。 相似文献
8.
9.
本文提出了一种新型的由普通圆柱直齿轮组成的端面谐波齿轮传动。给出了柔轮的原始曲面方程、柔轮和刚轮的齿廓曲面方程。讨论了该种传动的参数选择和啮合分析方法。计算结果和分析证明了这种端面谐波齿轮传动的工程实用价值,并可进一步推广使用。 相似文献
10.
11.
12.
13.
A novel specific type of worm drive, so-called end face engagement worm gear(EFEWD), is originally presented to minimize or overcome the gear backlash. Different factors, including the three different types, contact curves, tooth profile, lubrication angle and the induced normal curvature are taken into account to investigate the meshing characteristics and create the profile of a novel specific type of worm drive through mathematical models and theoretical analysis. The tooth of the worm wheel is very specific with the sine-shaped tooth which is located at the alveolus of the worm and the tooth profile of a worm is generated by the meshing movement of the worm wheel with the sine-shaped tooth, but just the end face of the worm(with three different typical meshing types) is adapted to meshing, and therefore an extraordinary manufacturing methods is used to generate the profile of the end face engagement worm. The research results indicates that the bearing contacts of the generated conjugate hourglass worm gear set are in line contacts, with certain advantages of no-backlash, high precision and high operating efficiency over other gears and gear systems besides the end face engagement worm gear drive may improve bearing contact, reduce the level of transmission errors and lessen the sensitivity to errors of alignment. Also, the end face engagement worm can be easily made with superior meshing and lubrication performance compared with the conventional techniques. In particular, the meshing and lubrication performance of the end face engagement worm gear by using the end face to meshing can be increased over 10% and 7%, respectively. This investigate is expect to provide a new insight on the design of the future no-backlash worm drive for industry. 相似文献
14.
15.
面齿轮传动分扭系统扭转振动的固有频率分析 总被引:2,自引:0,他引:2
基于集中质量法,建立了面齿轮传动分扭系统的动力学模型,模型中考虑了系统的扭转振动自由度。列出了系统的刚度矩阵和质量矩阵,求出了系统的各阶固有频率,分析了输入轴和面齿轮轴的扭转刚度以及面齿轮啮合刚度对系统固有频率的影响。结果表明,输入轴和面齿轮轴的扭转刚度对系统的高阶固有频率有较大的影响,面齿轮平均啮合刚度对系统的低阶固有频率有较大的影响。 相似文献
16.
为明晰齿轮马达密闭介质的制动机理及其制动性能的最大化措施,从齿轮副的啮合过程出发,由马达内介质作用的液压转矩等于马达外的负载转矩,推导出负载驱动转速的定量公式,并就制动性能最大化对齿形参数执行最优化设计。结果表明:啮合点的位置不同,负载驱动转速也不同,其中,最小困油位置处的最高,节点啮合处的最低;齿形参数对负载驱动转速的影响很大,案例优化前后的制动性能提高了31.2%~46.1%;负载转矩与马达内客观存在的泄漏途径为驱动转速产生的外因与内因,齿轮较小的宽径比和齿顶高系数能有效控制马达内泄漏等。研究成果为高质量齿轮马达的进一步研究与开发,提供一定的理论依据。 相似文献
17.
外啮合齿轮马达工作时产生的压力流量脉动是马达工作噪声的主要来源,而研究马达降噪的一个方法是利用齿轮马达模型分析优化齿廓曲线与齿轮啮合容积的动态关系。目前研究中的模型一般采用标准的渐开线或摆线进行仿真,而未体现齿廓曲线由于变位和加工误差对齿轮啮合容积的动态特性的影响。提出一种采用激光位移传感器对外啮合齿轮马达齿廓进行非接触测量的方法,搭建了齿形测试装置并采用MATLAB/C语言建立实际齿廓曲线,从而得到轮齿的齿形信息。试验结果对比了实际与理论马达齿轮齿廓,实现了齿廓测量,并提出改进齿轮马达非接触测量精度的方法。 相似文献