MoO3修饰氧化石墨烯作为空穴注入层影响研究

研究了MoO₃修饰氧化石墨烯(GO)作为空穴注入层的影响。采用旋涂的方法制备了GO, 再真空蒸镀修饰层MoO₃,得到了空穴注入能力强和透过率高的复合薄膜。MoO₃的厚分 别采用0、3、5和8nm。通过优化MoO₃的厚度发现,当MoO₃的厚为5nm时,复合薄膜 的透过率达到最大值,在 550nm的光波长下透光率为88%,且此时采用 复合薄膜作为空穴注入层制备的结构为 ITO/GO/MoO₃(5nm)/NPB(40nm)/Alq₃(40nm)/LiF(1nm)/Al(100nm)的有机电致发光器件(OLED)性能 最佳。通过对OLED进一步的优化,改变Alq₃的厚度,分别取50、60和70nm,测量其电压 、电流、亮度、色坐标和电致发光(EL)光谱等参数发现,当Alq₃的厚为50nm时器件性能最 佳。最终制备了结构为ITO/GO/MoO₃(5nm)/NPB(50nm)/Alq₃(50nm)/LiF(1nm)/Al(100 nm)的OLED,在电压为10V时,最大电流效率达到5.87cd/A,与GO单独作为空穴注入层制备的器件相比,提高了50%。     

MgF2缓冲层对蓝光OLED性能的影响

为了提高蓝光有机电致发光器件(OLED)的发光性能,将MgF2缓冲层插入ITO阳极与空穴传输层NPB之间,通过优化MgF2的厚度,制备了结构为ITO/MgF2(x nm)/NPB(50nm)/DPVBi:DSA-ph(30nm)/Alq3(30nm)/LiF(0.6nm)/Al(100nm)的高性能蓝光器件。实验结果表明,MgF2厚为1.0nm时,器件性能最佳,对应的器件最大电流效率达到5.51cd/A,最大亮度为23 290cd/m2(10.5V),与没有MgF2缓冲层的标准器件相比,分别提高47.3%和25.2%。对ITO表面的功函数测量结果表明,MgF2缓冲层可以有效修饰ITO表面,降低ITO与NPB之间的势垒高度差,改善空穴的注入效率,从而导致电子和空穴的注入更加平衡,激发机制更高效,实现了高性能的蓝光发射,为实现高效而稳定的全彩显示和白光照明奠定了基础。     

利用石墨烯掺杂在NPB中的OLED性能研究

采用NPB掺杂石墨烯作为空穴传输层,制备有机电致发光器件(OLED),器件结构为ITO/NPB:Graphene(20wt.%)(50nm)/Alq3(80nm)/LiF(0.5nm)/Al(120nm)。将其与标准器件ITO/NPB(50nm)/Alq3(80nm)/LiF(0.5nm)/Al(120nm)作性能比较,研究石墨烯对OLED性能的影响。结果表明,在NPB中掺杂石墨烯薄层的器件,在同等条件下性能最佳,当电流密度为90mA/cm2时器件电流效率达到最大值3.40cd/A,与标准器件最高效率相比增大1.49倍;亮度在15V时达到最大值10 070cd/m2,比标准器件最大亮度增大5.16倍。     

高效率磷光与荧光相结合的白色有机发光器件

制作了一种白色有机电致发光器件(WOLED)。将红光[Ir(piq)2(acac)]及绿光[Ir(ppy)3]磷光掺杂染料分别掺入到母体CBP中,在2种磷光发光层间插入蓝光材料DPVBi,引入电子传输能力强的BPhen作为电子注入层和空穴阻挡层,通过改变蓝光发光层的厚度,得到了高效率的WOLED,最大电流效率可达17.6cd/A,最大功率效率达13.7lm/W,最大亮度达27525cd/m2,当电压从4V变化到12V时,色坐标从(0.54,0.35)变化到(0.30,0.31),基本处于白光区。器件的特点在于DPVBi的存在阻挡了2种磷光材料间的能量转移,色度可以通过简单地调整DPVBi的厚度,避免使用稀有的蓝光磷光材料和与其相匹配的母体材料,同时又可以保持较高的发光效率。     

Blade coating of Tris(8-hydroxyquinolinato)aluminum as the electron-transport layer for all-solution blue fluorescent organic light-emitting diodes

Organic light-emitting diodes (OLEDs) with a low driving voltage and efficient blue fluorescence were fabricated through blade coating. Tris(8-hydroxyquinolinato)aluminum (Alq₃) is a relatively stable electron-transporting material commonly used in evaporation. However, depositing Alq₃ through a solution process is difficult because of its extremely low solubility organic solvents, a result of its symmetrical molecular structure. In this study, Alq₃ was successfully deposited through blade coating at a very low concentration below 0.1wt%. The OLEDs contained co-dopants BUBD-1 and p-bis(p-N,N-diphenyl-aminostyryl)benzene (DSA-Ph), and a high-band-gap host 2-methyl-9,10-bis(naphthalen-2-yl)anthracene (MADN) as the emission layer with the following structure: ITO/PEDOT:PSS (40 nm)/VB-FNPD (30 nm)/MADN:2% BUBD-1:1% DSA-Ph (50 nm)/TPBI (30 nm)/LiF (0.8 nm)/Al (100 nm)or ITO/PEDOT:PSS (40 nm)/VB-FNPD (30 nm)/MADN:3% BUBD-1 (50 nm)tris(8-hydroxyquinolinato)aluminum (Alq₃; 10 nm)/LiF (0.8 nm)/Al (100 nm). 2,7-disubstituted fluorene-based triaryldiamine(VB-FNPD)is the cross-linking transporting material. The device exhibited a peak current efficiency of 5.67 cd/A for Alq₃ and 5.76 cd/A for TPBI. The device with Alq₃ has operated lifetime seven times higher than the device with TPBI.     

Organic alternating current electroluminescence device based on 4,4′-bis(N-phenyl-1-naphthylamino) biphenyl/1,4,5,8,9,11-hexaazatriphenylene charge generation unit

An organic alternating current electroluminescence (OACEL) device based on 4,4′-bis(N-phenyl-1-naphthylamino) biphenyl (NPB)/1,4,5,8,9,11-hexaazatriphenylene (HAT-CN)/tris(8-hydroxy-quin-olinato) aluminum (Alq₃) doped with cesium carbonate (Cs₂CO₃) internal charge generation unit is demonstrated. Maximum luminance of 299 cd/m² is observed for Alq₃ doped with 10-(2-Benzothiazolyl)-2,3,6,7-tetrahydro-1,1,7,7-tetramethyl-1H,5H, 11H-(1) benzopyropyrano (6,7-8-I,j)quinolizin-11-one (C545T) fluorescent emission layer when driven with a peak–peak voltage of 80 V at 120 kHz. The key charge-generation role of NPB/HAT-CN interface is studied experimentally. Furthermore, influence of evaporation sequence of this internal charge generation unit on OACEL performance is investigated. This work demonstrated that the undoped charge generation unit – NPB/HATCN, can also be a good candidate for charge generation unit of OACEL device.     

功能层界面制备方法对OLED性能的影响

在功能层界面处采用各功能材料共蒸的方法,制备了典型的绿光有机发光器件(OLED)。器件的结构为ITO/NPB(37nm)/(NPB:Alq3)(3nm)/Alq3(27nm):C545T(3%)/Alq3(20nm)/LiF(1nm)/Al(100nm),并与传统的制备方法进行了比较。结果发现,起亮电压从4.5V降低到2.5V,最高耐压从16V提高到21V,最大亮度从13 940cd/m2提高到24 630cd/m2,发光效率由7.0cd/A提高到11.4cd/A。结果表明,本文方法有利于载流子传输,可以有效提高激子形成概率,提高了OLED发光效率。     

Molecular Engineering of Blue Fluorescent Molecules Based on Silicon End‐Capped Diphenylaminofluorene Derivatives for Efficient Organic Light‐Emitting Materials

Blue fluorescent materials based on silicone end‐capped 2‐diphenylaminofluorene derivatives are synthesized and characterized. These materials are doped into a 2‐methyl‐9,10‐di‐[2‐naphthyl]anthracene host as blue dopant materials in the emitting layer of organic light‐emitting diode devices bearing a structure of ITO/DNTPD (60 nm)/NPB (30 nm)/emitting layer (30 nm)/Alq₃ (20 nm)/LiF (1.0 nm)/Al (200 nm). All devices exhibit highly efficient blue electroluminescence with high external quantum efficiencies (3.47%–7.34% at 20 mA cm^?2). The best luminous efficiency of 11.2 cd A^?1 and highest quantum efficiency of 7.34% at 20 mA cm^?2 are obtained in a device with CIE coordinates (0.15, 0.25). A deep‐blue OLED with CIE coordinates (0.15, 0.14) exhibits a luminous efficiency of 3.70 cd A^?1 and quantum efficiency of 3.47% at 20 mA cm^?2.     

A DCM‐Type Red‐Fluorescent Dopant for High‐Performance Organic Electroluminescent Devices

2‐(2‐tert‐Butyl‐6‐((E)‐2‐(2,6,6‐trimethyl‐2,4,5,6‐tetrahydro‐1H‐pyrrolo[3,2,1‐ij]quinolin‐8‐yl)vinyl)‐4H‐pyran‐4‐ylidene)malononitrile (DCQTB) is designed and synthesized in high yield for application as the red‐light‐emitting dopant in organic light‐emitting diodes (OLEDs). Compared with 4‐(dicyanomethylene)‐2‐tert‐butyl‐6‐(1,1,7,7,‐tetramethyljulolidyl‐9‐enyl)‐4H‐pyran (DCJTB), one of the most efficient red‐emitting dopants, DCQTB exhibits red‐shifted fluorescence but blue‐shifted absorption. The unique characteristics of DCQTB with respect to DCJTB are utilized to achieve a red OLED with improved color purity and luminous efficiency. As a result, the device that uses DCQTB as dopant, with the configuration: indium tin oxide (ITO)/N,N′‐bis(1‐naphthyl)‐N,N′‐diphenyl‐1,1′‐biphenyl‐4,4′‐diamine (NPB; 60 nm)/tris(8‐quinolinolato) aluminum (Alq₃):dopant (2.3 wt %) (7 nm)/2,9‐dimethyl‐4,7‐diphenyl‐1,10‐phenanthroline (BCP; 12 nm)/Alq₃(45 nm)/LiF(0.3 nm):Al (300 nm), shows a larger maximum luminance (L_max = 6021 cd m^–2 at 17 V), higher maximum efficiency (η_max = 4.41 cd A^–1 at 11.5 V (235.5 cd m^–2)), and better chromaticity coordinates (Commission Internationale de l'Eclairage, CIE, (x,y) = (0.65,0.35)) than a DCJTB‐based device with the same structure (L_max = 3453 cd m^–2 at 15.5 V, η_max = 3.01 cd A^–1 at 10 V (17.69 cd m^–2), and CIE (x,y) = (0.62,0.38)). The possible reasons for the red‐shifted emission but blue‐shifted absorption of DCQTB relative to DCJTB are also discussed.     

Effect of Al:Ag alloy cathode on the performance of transparent organic light-emitting devices

Transparent organic light-emitting devices (TOLEDs) based on a stacked alloy cathode of LiF/Al:Ag are investigated. The devices have a structure of indium-tin-oxide (ITO)/4,4′,4′′-Tris[2-naphthyl(phenyl)amino]triphenylamine (2T-NATA) (25 nm)/N,N''-Di-[(1-naphthyl)-N,N''-diphenyl]-1,1''-biphenyl-4,4''-diamine (NPB) (40 nm)/tris-(8-hydroxyquinoline) aluminum (Alq3) (50 nm)/LiF (1 nm)/Al:Ag (1:3) (x), where the thicknesses of cathode metal layers (Al:Ag) are adjusted, respectively, from 70 nm to 100 nm. In the experiment, it is found that the LiF (1 nm)/Al:Ag (1:3) (75 nm) has good electron injection efficiency. Compared with an Al-only cathode, the turn-on voltage is lowered. At the voltage of 10 V, the luminances for bottom emission from ITO anode side and top emission from metal cathode side are 2 459 cd/m2 and 1 729 cd/m2, respectively. Thanks to electron injection enhancement by using Al:Ag cathode, we can obtain a better energy level matching between the cathode and the organic layer, thus the devices have lower turn-on voltage and higher luminance. The total transmittance of the devices can achieve about 40% at the wavelength of 550 nm.     

基于DOPPP的高效白光OLED器件

采用真空热蒸镀的方法,以荧光染料1-(2,5-d imethoxy-4-(1-pyrenyl)-phenyl)pyrene (DOPPP)为蓝发光 层,5,6,11,2-Tetraphenylnaphthacene (Rubrene)为黄发光层,制备了结构为ITO/m-M TDATA(10nm)/NPB(30nm)/ Rubrene (0.2nm)/ DOPPP (x nm)/TAZ(10nm)/Alq₃(30nm)/LiF(0.5nm)/Al的双发光层的高效白色有机电 致发光器件(OLED)。通过调整DOPPP层的厚度,研究器件的发光性能。当DOPPP层厚小 于25nm时,器件以 黄光发射为主;当DOPPP层厚为25nm时器件的性能最佳,在电流密度为209.18mA/cm²时,获得最 大亮度为9232cd/m²,在电流密度为103.712mA/cm²时获得最大电流效率4.68cd/A, 并随着驱动电压 的升高,器件的色坐标从(0.366,0.365)变化到(0.384,0.399),都在白光的范围之内;当DOPPP层厚度超过25nm时,器件的效率和亮度 都开始下降。     

蓝绿色磷光OLED的制备及发光性能研究

以mCP为主体发光材料,蓝绿色磷光染料BGIr1作 为掺杂剂,制备了6种不同BGIr1掺杂量的蓝绿色磷光有机电致发光器件(OLED),研究了不 同掺杂量对蓝绿色磷光OLED器件发光特性的影 响。制得器件的结构为ITO/MoO₃(20nm)/NPB(40nm)/mCP:BGIr1(x%,30nm)/BCP(10nm)/Alq₃(20 nm)/LiF/Al(100nm),其中x%为发光层中磷光染料BGIr1的掺杂量(质量分数)。结果表明,BGIr1掺杂量 为18%时,获得器件的发光性能最佳。18% BGIr 1掺杂器件在488nm和 512nm处获得两个主发射峰,当电 流密度为26.5mA/cm²时,获得最大发光效率为6.2cd/A;在15V驱动电压下,获得最大亮度为6970cd/cm², CIE坐标为(0.17,0.31)。这说明,BGI r1掺杂改善了器件的发光亮度和色纯度,提高了器件的发光效率。     

CdS薄层对有机电致发光器件性能的影响

将光电材料硫化镉(CdS)薄层插入到结构为ITO/NPB/Rubrene/NPB/DPVBi/Alq3/LiF/Al的白光有机发光器件(OLED)的Alq3和LiF之间,研究了CdS对OLED性能的影响。结果表明,0.1nm厚的CdS插入Alq3和LiF之间的器件性能最好。器件电压从7 V变化到14 V时,色度均在白光的中心区域;当电压为7V时,器件的最大电流效率为9.09cd/A;当电压为14V时,器件的最大亮度为16 370cd/m2。不加CdS时,当电压为8V时,器件的最大效率为5.16cd/A;当电压为14V时,最大亮度为6 669cd/m2。加CdS的器件比不加CdS的器件最大效率提高了1.76倍,最大亮度提高了2.42倍。     

Electronic structures of CuI interlayers in organic electronic devices: An interfacial studies of N,N′-diphenyl-N,N′-bis(1-naphthyl)-1,1′-biphenyl-4,4′-diamine/CuI and tris-(8-hydroxyquinolinato)aluminum/CuI

Electronic structures with the copper iodide (CuI) interlayer in organic electronic devices were measured and its strong electron-withdrawing properties were revealed. In situ ultraviolet and X-ray photoelectron spectroscopy showed the interfacial electronic structures of N,N′-diphenyl-N,N′-bis(1-naphthyl)-1,1′-biphenyl-4,4′-diamine (NPB)/CuI/indium–tin-oxide (ITO) and tris-(8-hydroxyquinolinato)aluminum (Alq₃)/CuI/ITO as a representative hole- and electron-transport material. The large work function of the CuI interlayer induces electron transfer from both molecules and ITO to CuI. As a result, CuI dramatically reduces the hole injection barrier (HIB) from ITO to NPB and Alq₃ layers. Notably, CuI assists molecular ordering of the NPB layer, which would increase the intermolecular interaction, so would enhance the charge transport properties. Simultaneous enhancement in HIB and molecular ordering with the CuI interlayer would improve the device performance.     

一种新型蓝色有机电致发光器件及其发光机理

利用5,6,11,12-tetraphenylnaphthacene(Rubrene)超薄层制备了一种蓝光有机电致发光器件(OLED),器件结构为ITO/N,N'-diphenyl-N,N'-bis(1-naphthyl)-(1,18-biphenyl)-4,4'-diamine(NPB)(50nm)/2,9-d...     

有机白光器件中CdS薄层增加电子注入的研究

为了研究光电材料CdS在有机白光器件中增加电子注入的特性,将结构为ITO/NPB/Rubrene/NPB/DPVBi/Alq3/LiF/Al的白光器件,不插入CdS薄层或将CdS薄层分别插入到NPB和ITO之间以及Alq3和LiF之间或同时将CdS薄层插入到它们之间,制作了四个元器件。通过研究得出,在Alq3和LiF之间插入CdS薄层的器件,在同等条件下性能较好。性能的改善来自于CdS薄层的引入使器件电子注入增加,激子形成的数量和比率也获得了相应的提高,从而提高了器件的亮度和效率。     

Low sublimation temperature cesium pivalate complex as an efficient electron injection material for organic light-emitting diode devices

Cesium pivalate ((CH₃)₃CCOOCs) has been synthesized and applied as an electron injection material for organic light-emitting diodes, which showed low sublimation temperature of 180 °C. Typical bilayer structure of ITO/NPB (60 nm)/Alq₃ (50 nm)/EIL/Al was used to evaluate the electron injection efficacy of (CH₃)₃CCOOCs, the results showed (CH₃)₃CCOOCs/Al exhibits better electron injection than LiF/Al cathode and the power efficiency was improved by about 19% at current density of 50 mA/cm². More interestingly, in the typical three layer OLED structure ITO/2-TNATA (60 nm)/NPB (10 nm)/Alq₃:2% C545T (40 nm)/MADN (15 nm)/(CH₃)₃CCOOCs (2 nm)/Al, the maximum current efficiency is up to 20 cd/A with Commission Internationale d’Eclairage (CIE_x,_y) color coordinates of (x = 0.30, y = 0.65) at current density of 140 mA/cm², which indicates that the non-aromatic alkali metal complex can also have good match with the chemically stable compound and exhibit good electron injection properties.     

Improved property in organic light-emitting diode utilizing two Al/Alq3 layers

We reported on the fabrication of organic light-emitting devices (OLEDs) utilizing the two Al/Alq₃ layers and two electrodes. This novel green device with structure of Al(110 nm)/tris(8-hydroxyquinoline) aluminum (Alq₃)(65 nm)/Al(110 nm)/Alq₃(50 nm)/N,N′-dipheny1-N, N′-bis-(3-methy1phyeny1)-1, 1′-bipheny1-4, 4′-diamine (TPD)(60 nm)/ITO(60 nm)/Glass. TPD were used as holes transporting layer (HTL), and Alq₃ was used as electron transporting layer (ETL), at the same time, Alq₃ was also used as emitting layer (EL), Al and ITO were used as cathode and anode, respectively. The results showed that the device containing the two Al/Alq₃ layers and two electrodes had a higher brightness and electroluminescent efficiency than the device without this layer. At current density of 14 mA/cm², the brightness of the device with the two Al/Alq₃ layers reach 3693 cd/m², which is higher than the 2537 cd/m² of the Al/Alq₃/TPD:Alq₃/ITO/Glass device and the 1504.0 cd/m² of the Al/Alq₃/TPD/ITO/Glass. Turn-on voltage of the device with two Al/Alq₃ layers was 7 V, which is lower than the others.     

Four-wavelength white organic light-emitting diodes using 4,4′-bis-[carbazoyl-(9)]-stilbene as a deep blue emissive layer

White organic light-emitting diodes (WOLEDs) with four wavelengths were fabricated by using three doped layers, which were obtained by separating recombination zones into three emitter layers. Among these emitters, blue emissions with two wavelengths (456 and 487 nm) were occurred in the 4,4′-bis(carbazoyl-(9))-stilbene (BCS) host doped with a perylene dye. Also, a green emission was originated from the tris(8-quinolinolato)aluminum (III) (Alq₃) host doped with a green fluorescent of 10-(2-benzothiazolyl)-1,1,7,7-tetramethyl-2,3,6,7-tetrahydro-1H,5H,11H-[1]benzopyrano [6,7,8-ij]-quinolizin-11-one (C545T) dye. Finally, an orange emission was obtained from the N,N′-bis(1-naphthyl)-N,N′-diphenyl-1,1′-biphenyl-4,4′-diamine (NPB) host doped with a 4-(dicyanomethylene)-2-tert-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) dye. The white light could be emitted by simultaneously controlling the emitter thickness and concentration of fluorescent dyes in each emissive layer, resulting in partial excitations among those three emitter layers. Electroluminescent spectra of the device obtained in this study were not sensitive to driving voltage of the device. Also, the maximum luminance for the white OLED with the CIE coordinate of (0.34, 0.34) was 56,300 cd/m² at the applied bias voltage of 11.6 V. Also, its external quantum and the power efficiency at about 100 cd/m² were 1.68% and 2.41 lm/W, respectively.     

An organic light-emitting devices of highly efficient white phosphor using an electron/exciton blocker

Highly efficient white phosphorescent organic light-emitting devices （WOLEDs） was fabricated using an electron/exciton blocker. The device structure is ITO/2T-NATA（25 nm）/NPBX（25-dnm）/CBP：5%Ir（ppy）3：0.5%Rubrene（8 nm）/NPBX（dnm）/ DPVBi（30 nm）/TPBi（20 nm）/Alq（10nm）/LiF（1nm）/A1, in which N,N ＇ -bis- （1-naphthyl）- N,N ＇ -dipheny1-1, 1 ＇ - biphenyl-4,4 i -diamine （NPBX） functions as a hole transport layer and electron/exciton blocker, 4,4,N,N ＇ dicarbazolebiphenyl （CBP） is host, 4,4＇ -bis（2,2 -diphenyl vinyl）-1,1 ＇ -biphenyl （DPVBi） is blue fluorescent dye, 5,6,11, 12,-tetraphenylnaphthacene （rubrene） is fluorescent dye, factris （2-phenylpyridine） iridium （Ir（ppy）3） is phosphorescent sensitizer and tris（8-hydroxyquinoline） aluminum （Alq3） is an electron transport layer. The WOLEDs have obtained white light emission by adjusting the thickness of NPBX, when the concentration of Ir（ppy）3 is 5-wt% and rubrene is 0.5-wt%, respectively, the thickness of the doped emissive layer is 8 nm, the WOLEDs show a maximum luminous efficiency is 11.2 cd/ A with d of 10 nm at 7 V and a maximum luminance of 28170 cd/m^2 at 17 V, the CIE coordinates is （0.37.0.42）, which is in white region.