Reduction in cholesterol and fractionation of butter oil using supercritical CO2 with adsorption on alumina

Cholesterol reduction together with the fractionation of triglycerides in butter oil was obtained using a combined supercritical CO₂ extraction/alumina adsorption process in a high-pressure apparatus that allows the independent control of temperature and pressure. Cholesterol levels in butter oil fractions extracted at 40 °C and 27.6 MPa were reduced from 2.5 to 0.1 mg g⁻¹ of oil. Butter oil was also fractionated into low-, intermediate- or high-molecular-weight triglycerides. This single-stage combined process is a clear indication of the important technological possibilities with a more efficient multistage fractionation followed by the subsequent blending and formation of desired milk fat products. A comparison of solubility data of pure cholesterol in CO₂ with those for cholesterol contained in butter oil revealed the co-solvency effects of triglycerides on the solvation of cholesterol.     

Temperature-Sensitive Microcapsules Containing Lactoferrin and Their Action Against Carnobacterium viridans on Bologna

ABSTRACT:  Lactoferrin (LF) was encapsulated in 2 types of emulsion to protect it from contact with agents like divalent cations, which interfere with its antimicrobial activity. First, paste-like microcapsules were prepared as water-in-oil (W₁/O) emulsions from mixtures of 20% w/v LF in distilled water, 20% w/v LF in 3% w/v sodium lactate or in 20 mM sodium bicarbonate, which were emulsified with an oil mixture of 22% butter fat plus 78% corn oil and 0.1% polyglycerol polyricinoleate. Second, freeze-dried double emulsion (W₁/O/W₂), powdered microcapsules were produced following emulsification of paste-like microcapsules in an external aqueous phase (W₂) consisting of a denatured whey protein isolate (WPI) solution. The release of LF from the W₁/O microcapsules was dependent on temperature and NaCl concentration. LF was not released from the W₁/O emulsion at <5.5 °C. Its release was greater from W₁/O microcapsules when suspended in 5% aqueous NaCl than in water at ≥10 °C, whereas LF release from freeze-dried microcapsules was not controlled by temperature change. Paste-like microcapsules were incorporated in edible WPI packaging film to test the antimicrobial activity of LF against a meat spoilage organism Carnobacterium viridans . The film was applied to the surface of bologna after its inoculation with the organism and stored under vacuum at 4 or 10 °C for 28 d. The growth of C. viridans was delayed at both temperatures and microencapsulated LF had greater antimicrobial activity than when unencapsulated. The temperature-sensitive property of the W₁/O microcapsules was reduced when they were incorporated into a WPI film.     

Artificial neural network modeling for temperature and moisture content prediction in tomato slices undergoing microwave-vacuum drying

ABSTRACT:  Inputs for ANN (multihidden-layer feed-forward artificial neural network) models were drying time ( t _{i + 1}), initial temperature ( T ₀), moisture content ( MC ₀), microwave power, and vacuum pressure. The outputs were temperature ( T _{i + 1}) and moisture content ( MC _{i + 1}) at a given t _{i + 1}. After training the ANN models with experimental data using the Levenberg-Marquardt algorithm, a two-hidden-layer model (25-25) was determined to be the most appropriate model. The mean relative error (MRE) and mean absolute error (MAE) of this model for T _{i + 1} were 1.53% and 0.77 °C, respectively. In the case of MC _{i + 1}, the MRE and MAE were 11.48% and 0.04 kg_water/kg_dry, respectively. Using temperature ( T _i ) and moisture content ( MC _i ) values at t _i in the input layer significantly reduced the computation errors such that MRE and MAE for T _{i + 1} were 0.35% and 0.18 °C, respectively. In contrast, these error values for MC _{i + 1} were 1.78% (MRE) and 0.01 kg_water/kg_dry (MAE). These results indicate that ANN models were able to recognize relationships between process parameters and product conditions. The model may provide information regarding microwave power and vacuum pressure to prevent thermal damage and improve drying efficiencies.     

Fate of Aflatoxin M1 during Manufacture and Storage of Feta Cheese

ABSTRACT:  The effect of feta cheese manufacture on aflatoxin M₁ (AFM₁) content was studied using an enzyme immunoassay technique. Feta cheese was made from milk spiked with 1 and 2 μg AFM₁ per kilogram milk. Pasteurization at 63 °C for 30 min caused <10% destruction of AFM₁. During cheese making, the remaining AFM₁ in milk was partitioned between curd and whey with two-thirds retained in the curd and one-third going into the whey. Cheeses were then stored for 2 mo in 8%, 10%, and 12% brine solutions at 6 and 18 °C. There was a 22% to 27% reduction of AFM₁ during the first 10 d of storage, with slightly more loss as salt concentration increased and when the cheese was stored at 18 °C. Further storage caused only slight decrease in AFM₁ and after 30 d of brining there was no difference in AFM₁ content of the cheese based upon salt concentration of the brine. At 18 °C, no further losses of AFM₁ occurred after 30 d, and at 6 °C, there was continued slight decrease in AFM₁ levels until 50 d. After 60 d of brining, there was a total loss of 25% and 29% of the AFM₁ originally present for cheese brined at 6 and 18 °C, respectively. Thus, the combination of pasteurization, conversion of milk into feta cheese, and at least 50 d storage of cheese in brine caused a total loss of about 50% of the AFM₁ originally present in the raw milk.     

EARLY DETECTION OF CLOSTRIDIUM PERFRINGENS ENTEROTOXIN AND ITS RELATIONSHIP TO SENSORY QUALITY OF COOKED CHICKEN

Growth, sporulation, and enterotoxin formation by Clostridium perfringens NCTC 8239 were determined in chicken thigh meat incubated at 45°C for 1.5 h and 37°C for up to 12.5 h. With an inoculum of 10⁶ vegetative cells per g, the cell counts reached mean log ₁₀ 7.32/g after 6 h of incubation and remained in that range through 14 h. Heat-resistant spores (log₁₀ 2.48/g) were first detected at 4 h, and the number increased to log₁₀ 5.19/g at 14 h. Enterotoxin (0.19 μg/g) was first detected after 2 h of incubation (1.5 h at 45°C and 0.5 h at 37°C) in the absence of detectable sporulation, and the enterotoxin concentration increased to 0.76 μg/g after 14 h. Significant differences (p < 0.01) in the odor, color, and texture scores for inoculated versus uninoculated cooked chicken following 2 h incubation correlated with the production of enterotoxin and suggested that these parameters could be used as indices of chicken spoilage by C. perfringens.     

RHEOLOGICAL BEHAVIOR OF PROCESSED MUSTARD. II. STORAGE EFFECTS

Samples of processed yellow mustard with three different particle size distributions (slightly-coarse, standard, and fine) were prepared according to a standard formulation and pilot-plant replication of the commercial methodology and stored for 3 months at 5°C, 25°C, and 45°C. After 3-month storage at 45°C, all samples showed visible liquid separation (syneresis) and aggregation of colloidal particles, as indicated by increase in d _pop and decrease in % colloids. The fine milled samples exhibited syneresis and an increase in d _pop after 3-month storage even at 25°C. The bimodal distribution did not show significant changes as a result of aggregation. In general, increase in d _pop increased apparent viscosity (η _ap ), flow behavior index (n) from the Herschel-Bulkley model, and exponent n" from the loss modulus (G") power law equation. As d _pop increased, Bingham yield stress _o), plastic apparent viscosity (η _p ), shear stress constant (A) from the Weltman stress decay model, yield stress (_o) and consistency index (m) from the Herschel-Bulkley model, exponent n' from the storage modulus (G') power law equation, and minimum values of loss tangent (tan δ) decreased. In heterodisperse semi-solid foods such as processed mustard, the particle size distribution influences the structure (i.e., packing) and the rheological behavior. Therefore, time and temperature dependent instabilities such as syneresis may be minimized by controlling particle size distribution during processing.     

COMPARISON OF STEADY SHEAR RHEOLOGICAL PROPERTIES AND SMALL AMPLITUDE DYNAMIC VISCOELASTIC PROPERTIES OF FLUID FOOD MATERIALS

Small amplitude dynamic viscoelastic properties of apple butter, mustard, tub margarine, and mayonnaise are compared with their respective properties in steady shear flow in the range of shear rates and frequencies of 0.1-100 sec⁻¹ using a Rheometrics Mechanical Spectrometer. Comparison of dynamic and steady viscosities shows that dynamic viscosities (η*) are much larger than steady viscosities (η). Consequently the Cox-Merz rule is not obeyed. Moreover the obvious nonlinearity suggests that shift-factor type relationships are not obeyed either. The in-phase (η') component of the dynamic viscosity shows similar behavior when compared to the steady viscosity (η).
Comparison of G'/ω² and Ψ₁ also suggests that any of the results predicted by classical theories of viscoelasticity are not obeyed. G'/ω² is always much larger than Ψ₁ and the relationship between these two material functions is nonlinear.     

Acidified Sodium Chlorite as an Alternative to Chlorine for Elimination of Salmonella on Alfalfa Seeds

ABSTRACT:  The health and environmental hazard associated with the use of chlorine for food processing has been documented previously. This study was conducted to determine if acidified sodium chlorite (ASC) could be used to replace calcium hypochlorite (Ca[OCl]₂) for disinfection of alfalfa seeds. Contaminated seeds containing approximately 1.5 × 10⁷ CFU/g of Salmonella were treated with ASC or Ca(OCl)₂ at different concentrations and for different periods of time. Results showed that the efficacy of ASC and Ca(OCl)₂ for elimination of Salmonella on contaminated seeds could be improved greatly by extending the treatment time from the traditional 15 to 45 min. Treatment of seeds with 800 ppm of ASC for 45 min reduced the number of Salmonella by 3.9 log units, approximately 1.2 log units higher than that treated with 20000 ppm of Ca(OCl)₂. Treatment of seeds with a lower concentration (100 to 400 ppm) of ASC for 45 min reduced the number of Salmonella by 1.3 to 2.2 log units. Soaking alfalfa seeds in 800 ppm of ASC for 45 min did not affect seed germination. However, soaking seeds in 20000 ppm of Ca(OCl)₂ for 45 min reduced seed germination by 20%. Unlike Ca(OCl)₂, antimicrobial efficiency of ASC was not affected by pre-exposure to alfalfa seeds. Data presented also showed that Salmonella on newly inoculated seeds that had been stored at 4 °C for less than 7 d were more sensitive to sanitizer treatment than those on seeds that had been stored for 4 wk or longer.     

Sorbic acid diffusivity in relation to the composition of high and intermediate moisture model gels and foods

The diffusivity at infinite diffusant dilution ( D ₀) of sorbic acid in high and intermediate moisture gels (with various substrates and water contents) and in three foods was evaluated. The determination of D ₀(25°C) was achieved by tridimensional diffusion in gels cubes or by monodimensional diffusion in infinite food columns. For the same substrate concentration by weight, D₀ values of sorbic acid in concentrated sugar solutions decreased slightly when the molecular weight of the sugar was increased. When a liquid substrate such as glycerol was used, D ₀ values referred to equal concentrations by weight, were higher than in sugar solutions. The diffusion of sorbic acid is related, as a first approximation, to the water content rather than to the water activity of the diffusion medium.     

Influence of vitamin E supplementation on spontaneous oxidized flavour of milk in dairy buffaloes

Twenty-four Murrah buffaloes (60 days pre-partum) were divided into four equal groups (T ₁ , T ₂ , T ₃ and T ₄ ) and were supplemented with 0, 1000, 1500 and 2000 IU α-tocopheryl acetate per day up to 30 days of lactation, and half of these doses from 30 to 60 days of lactation. Milk samples collected fortnightly were analysed for vitamin E, fat, and development of oxidized flavour, with and without copper addition by a panel of judges, and chemically by the thiobarbituric acid test. Scores for oxidized flavour ranged from 0 to 10 with 0–4 as definite, 5–7 as light and 8–10 having no defect. The α-tocopherol content in milk fat (µg/g) averaged 20.55, 25.56, 29.98 and 31.38 in T ₁ , T ₂ , T ₃ and T ₄ groups, respectively. The addition of Cu in the milk significantly increased milk fat oxidation. Better stability of milk in T ₃ and T ₄ groups was observed, which might be due to a higher level of milk α-tocopherol. Addition of 1500 IU α-tocopheryl acetate in the diet of buffaloes helped in improving the oxidative stability of milk.     

Determination of a process time for a new product: canned low acid artichoke hearts

In order to obtain a process time for canned low acid artichoke hearts, the heat resistance of Clostridium sporogenes PA 3679 in phosphate buffer (pH 7) and in artichoke puree (pH 5.2) was determined in the range of 100–118°C. D _T values in artichoke puree were determined by the most probable number and plate count methods. D _121°C values were deduced by extrapolation of the curves. An F 8.3/121 (see nomenclature section) target value of 1.8 min, equivalent to an F ₀= 2.5 min, was established considering a D _121°C value of 0.36 min for artichoke puree. The cold point for canned artichoke hearts in 1/2 kg (71.5x117 mm) cans was determined, a set of heat penetration and cooling curves were obtained and the values of the parameters ' j ' and ' f ' were found. A process time was deduced, 21.5 and 23 min of heating at 121°C, following the methods of Patashnik (1954) and Hayakawa (1970, 1974) respectively, in order to reach the F ₀ target of 2.5 min for this new canned food. This process was adequate, as the inoculated experimental pack test showed no altered cans out of 50 inoculated after 21.5 min of heating at 121°C.     

Artificial neural network for the prediction of temperature, moisture and fat contents in meatballs during deep-fat frying

An artificial neural network (ANN) was developed to predict heat and mass transfer during deep-fat frying of meatballs. Frying time, radius of meatball, fat diffusivity, moisture diffusivity, heat transfer coefficient, fat conductivity, initial moisture content, thermal diffusivity, initial meatball temperature and oil temperature were all input variables. Temperature at meatball geometrical centre ( T ₀), average temperature of meatball ( T _ave), average fat content of meatball ( m _f,ave), and average moisture content of meatball ( m _ave) were outputs. The data used to train and verify the ANN were obtained from validated mathematical models. Trained ANN predicted T ₀, T _ave, m _f,ave and m _ave with 0.54, 0.14, 0.03 and 0.10% mean relative errors, respectively.     

New Kinetic Approach to the Evolution of Polygalacturonase (EC 3.2.1.15) Activity in a Commercial Enzyme Preparation Under Pulsed Electric Fields

ABSTRACT:  The effect of pulsed electric fields (PEF) on polygalacturonase (PG) activity in an aqueous solution of a commercial enzyme preparation was studied. Monopolar square wave pulses of 4 μs were delivered to the solution, which circulated through tubular chambers with 2 stainless steel electrodes in continuous operation. The electric field intensities ( E ) and treatment time ( t ) ranged within 15 to 38 kV cm⁻¹ and 300 to 1100 μs, respectively. Although important reduction of the PG activity could be achieved (up to 76.5% at E = 38 kV cm⁻¹ and t = 1100 μs), the experimental data showed certain enhancement of PG activity under soft conditions (up to 110.9% at E = 15 kV cm⁻¹ and t = 300 μs). A kinetic mechanism involving 2 consecutive irreversible first-order steps was developed to describe and explain the experimental data. The tested model exhibited high accuracy in respect of the experimental data and the error of the model was lower than 4.4%. The kinetic rate constant of the first ( k ₁) and second step ( k ₂), ratio between the activities of intermediate and native forms of the enzyme (Λ), and other quantities related to the model, were obtained within a Bayesian framework. k ₁ resulted independent of the E applied and considerably greater in magnitude order ( k ₁ mean = 6 μs⁻¹) with respect to k ₂, which was dependent on the applied E (mean values ranged from 489E-6 μs⁻¹ at E = 38 kV cm⁻¹ to 1215E-6 μs⁻¹ at 38 kV cm⁻¹). The dependency of k ₂ toward E was described using an exponential relationship.     

Thermal Conductivity of Pear, Sweet-cherry, Apricot, and Cherry-plum Juices as a Function of Temperature and Concentration

ABSTRACT:  The thermal conductivity of 4 fruit (pear, sweet-cherry, apricot, and cherry-plum) juices was measured with a coaxial-cylinder (steady-state) technique. Measurements were made, temperature range 20 to 120 °C, at concentrations between 12.2 and 50 °Brix. The uncertainty of the thermal conductivity measurements was estimated to be less than 2%. A semitheoretical method for the prediction of thermal conductivity of juices was proposed. It was found that the prediction Model IV,  λ ( T , x )/λ ( T ₀, x ) = ( T / T ₀) ⁿ   , where  λ  is the thermal conductivity, x is the concentration, and T is the temperature, developed in this work can be adopted with satisfaction. The thermal conductivity of juices can be predicted just by knowing the thermal conductivity  λ₀  at a reference temperature   T ₀  .     

Characteristics of palm mid-fractions produced from different fractionation paths and their potential usages

Three palm mid-fraction (PMF) groups produced from different fractionation paths were analyzed in terms of the fat, triacylglycerol and sn-2 fatty acid compositions, thermal properties (melting and crystallization behaviors, and solid fat contents (SFCs)), micronutrient levels and oxidative stability indexes (OSIs) to achieve their sufficient utilization. PMF-A (iodine value (IV), 48.4 g/100 g) fractionated from palm olein contained 43.8% 1,3-dipalmitoyl-2-oleoyl-glycerol (POP) and 16.7% 1-palmitoyl-2,3-dioleoyl-glycerol, showing soften properties (slip melting point (SMP), 27.6°C; SFC at 30°C, 2.2%) at hot weather. PMF-B (IV, 42.3 g/100g) obtained from palm stearin showed similar fat and triacylglycerol compositions as PMF-A, but the high 1,2,3-tripalmitoyl-glycerol level (6.2%) improves its thermal behaviors (SMP, 34.9°C; SFC at 30°C, 13.8%). The SFC profiles of PMF-A and PMF-B were comparable to those found in frozen and puff margarine shortenings. Furthermore, both of the PMF groups exhibited excellent OSIs (13.2 and 11.2 h, respectively) because of their high micronutrient levels (especially γ-tocopherol and campesterol). In general, γ-tocopherol and campesterol contribute to preventing lipids from oxidation under frying conditions. Therefore, PMF-A and PMF-B are recommended for manufacturing margarine shortenings and frying fasts. PMF-C (IV, 33.0 g/100g) produced from the additional fractionation of PMF-A or PMF-B contained the highest POP percentage (67.1%) and showed heat-resistant property (SMP, 31.8°C; SFC at 30°C, 22.4%). Its steep SFC profile was superior to that of cocoa butter, suggesting the fat is preferred in producing hard chocolate fats.     

Rheology and Oxidative Stability of Whey Protein Isolate-Stabilized Menhaden Oil-in-Water Emulsions as a Function of Heat Treatment

ABSTRACT:  Menhaden oil-in-water emulsions (20%, v/v) were stabilized by 2 wt% whey protein isolate (WPI) with 0.2 wt% xanthan gum (XG) in the presence of 10 mM CaCl₂ and 200 μM EDTA at pH 7. Droplet size, lipid oxidation, and rheological properties of the emulsions were investigated as a function of heating temperature and time. During heating, droplet size reached a maximum at 70 °C and then decreased at 90 °C, which can be attributed to both heating effect on increased hydrophobic attractions and the influence of CaCl₂ on decreased electrostatic repulsions. Combination of effects of EDTA and heat treatment contributed to oxidative stability of the heated emulsions. The rheological data indicate that the WPI/XG-stabilized emulsions undergo a state transition from being viscous like to an elastic like upon substantial thermal treatment. Heating below 70 °C or for less than 10 min at 70 °C favors droplet aggregation while heating at 90 °C or for 15 min or longer at 70 °C facilitates WPI adsorption and rearrangement. WPI adsorption leads to the formation of protein network around the droplet surface, which promotes oxidative stability of menhaden oil. Heating also aggravates thermodynamic incompatibility between XG and WPI, which contributes to droplet aggregation and the accumulation of more WPI around the droplet surfaces as well.     

Effect of different extraction and precipitation methods on yield and quality of pectin

An experimental study has been conducted to determine the combined effects of different extraction conditions and precipitation method on the yield and quality of high methoxyl pectin from lemon peels. Pectin was extracted using different mineral acids (HCl, HNO₃ and H₂SO₄) at four concentration levels (0.025; 0.05; 0.1 and 0.2  m ), at 70 °C for 4 h. The soluble pectin was precipitated by iso-propanol or by an aluminium sulphate, Al₂(SO₄)₃, solution at pH 4. The extraction with HCl and HNO₃, at the highest concentrations investigated, followed by aluminium precipitation led to the best results in terms of yield (22–25%), quality and gelling power of pectin with a remarkable decrease of alcohol consumption as compared to the alcoholic precipitation under the same extracting conditions.     

The Effects of Residual Oxygen on the Storage Life of Retail-Ready Fresh Beef Steaks Masterpackaged Under a CO2 Atmosphere

ABSTRACT:  Retail-packed rump ( Gluteus medius , GM) and striploins ( Longissiumus dorsi, LD) steaks were masterpackaged under carbon dioxide (CO₂) and stored at 1 °C ± 1 °C for 14, 28, 35, and 42 d. A commercial oxygen (O₂) scavenger (ATCO HV1000®, Standa Industrie, Caen, France) was used in the masterpacks to achieve an O₂-free atmosphere. Similar packages without the O₂ scavengers were also prepared. At each storage time, 2 masterpacks of each treatment were opened and the retail trays were placed in a display case at 4 °C ± 2 °C for 1 and 48 h for microbiological and sensorial evaluations. The low growth rate of aerobic psychrotrophic flora on the stored beefsteaks demonstrated the bacteriostatic effect of CO₂ during storage. The maximum level of psychrotrophic aerobic bacteria reached during storage was approximately 10⁶ CFU/g. The steaks stored in masterpacks with scavengers bloomed to the desirable red color associated with freshly cut meat in the display case for all of the storage periods, except in the case of GM steaks, which showed a cycle of transient discoloration. GM and LD steaks were well accepted (65% and 82%, respectively) after 42 d under CO₂ at 1 °C ± 1 °C. The GM and LD steaks stored without the O₂ scavenger showed variable fractions of discoloration that significantly detracted from the appearance of the samples.     

Extending the shelf life of kohlrabi stems by modified atmosphere packaging

ABSTRACT:  Kohlrabi stems (without leaves) were stored under modified atmosphere packaging (MAP) for 60 d at 0 °C. An additional retail sale period of 3 d at 12 °C after each cold storage evaluation (30 and 60 d) was applied. Under high relative humidity (RH) and 0 °C, the stems showed low metabolic activity, as no changes in sugars and organic acids were found. From day 21 at 0 °C, air-stored stems showed a yellowing of stalks and later they fell down. This disorder severely affected the appearance of stems. A gas composition of 4.5 to 5.5 kPa O₂ plus 11 to 12 kPa CO₂ was reached using antimist oriented polypropylene plastic bags of 20-μm thicknesses. The stems in MAP conditions kept a high sensorial quality. It was enough for commercial purpose of 2 mo. The storage of kohlrabi stems in plastic bags, either MA or in perforated (control) packages, provided an additional protection reducing physical damage. The MAP conditions delayed the weight loss and development of bacterial soft and black rot, extending the shelf life of kohlrabi stems to 60 d at 0 °C plus 3 d at 12 °C. Stems are not chilling injury sensitive.     

Modifying the physical properties of butter using high-intensity ultrasound

The physical qualities of butter are affected by the physical properties of the cream used to make it. The objective of this study was to evaluate the effect of high-intensity ultrasound (HIU) on the physical properties of cream and butter. High-intensity ultrasound (frequency: 20 kHz, amplitude: 108 µm), often called sonication, was applied for 0, 10, 30, 60, and 90 s using a 1.27-cm-diameter tip to heavy cream (40% fat; 300 g) that was aged at 7.5°C with low agitation (40 rpm) for 90 min. Sonicated cream was churned at 7.5°C until butter grains were formed. The solid fat content (SFC), melting behavior, and average fat droplet size of cream were measured after HIU treatment. Butter was characterized by SFC and melting behavior immediately after production and was tested for SFC, melting behavior, and hardness after storage for 24 h at 5°C. High-intensity ultrasound did not affect the average fat droplet size of cream. Sonicating cream for 30, 60, and 90 s slightly decreased SFC due to the temperature increase (2–6°C) that occurred during HIU application. Two melting peaks were observed at approximately 17 and 33°C in all the cream samples. A significantly lower peak temperature was observed in cream sonicated for 10 s compared with creams sonicated for 30 and 60 s. A relatively shorter churning time of sonicated cream compared with nonsonicated cream was observed, possibly because HIU weakens the fat globule membrane. Two melting peaks were observed in all butter samples at approximately 16 and 33°C. Treatment with HIU for 10 to 60 s significantly increased the hardness of butter. When HIU was applied to cream for 10 s, the hardest butter was obtained, with the lowest onset temperatures and highest enthalpy values for both melting peaks. Treatment with HIU for 10 s promoted crystallization of low-melting-point triacylglycerols (TAG) during churning, which resulted in a harder material. Significantly lower enthalpy values for the high-melting-fraction TAG were observed in butters treated with HIU for 60 and 90 s compared with non-HIU-treated butter, which suggests that a longer duration of HIU promotes melting of high-melting-point TAG. The hardness of butter was correlated with the enthalpy values of the low-melting fraction and with total enthalpy values of fresh butter. However, further crystallization occurred in the butter during 24 h of storage at 5°C, and all differences in enthalpy values disappeared. In conclusion, exposure of cream to HIU can be used to modify the physical properties of butter, and the effects of HIU depend on the length of HIU treatment.