Silver nanocrystal-modified silicon nanowires as substrates for surface-enhanced Raman and hyper-Raman scattering

Metal catalyzed, CVD-grown silicon nanowires decorated by chemical assembly of closely spaced Ag nanocrystals were modified with the well-known "silver mirror" reaction and investigated as substrates for surface-enhanced Raman (SERS) and hyper-Raman (SEHRS) spectroscopy. Four chromophores were examined: Rhodamine 6G, crystal violet, a cyanine dye, and a cationic donor-acceptor substituted stilbene. After soaking the substrates overnight in 10(-4) M aqueous chromophore solutions, all four chromophores gave good-quality SERS spectra in < or =60 s using <1 microW of 458-nm cw laser power, and SEHRS spectra are obtained in < or =120 s using <1 mW of mode-locked 916-nm laser power. Results from this substrate are compared with those on colloidal silver nanoparticles deposited as a film, as well as surfaces grown by the silver mirror reaction.     

Intracellular pH sensing using p-aminothiophenol functionalized gold nanorods with low cytotoxicity

We report an intracellular pH sensor based on surface enhanced Raman scattering (SERS) using the hydrochloric acid (HCl) treated gold nanorods (GNRs) as the SERS substrates and p-aminothiophenol (pATP) as the Raman reporter. Using the HCl treated GNRs previously reported by us, the biocompatibility and the SERS performance of GNRs have been greatly improved. Meanwhile, the adsorbed reporters are allowed to be directly exposed to the surrounding environments, which is very important for biosensors. It is found that the SERS spectrum of pATP is strongly dependent on the pH value. The intensities of SERS bands at 1142 cm(-1), 1390 cm(-1), and 1432 cm(-1) increased obviously with the pH value varying from 3.0 to 8.0. This pH-dependent SERS performance of pATP-functionalized HCl treated GNRs was well retained after the incorporation of the GNRs into living HeLa cells. Our experimental results indicate that such pATP-functionalized HCl treated GNRs can be used as an effective intracellular pH sensor. Thus, we show a good example that the bioapplications of the normal CTAB-stabilized GNRs can be expanded after the simple HCl treatment.     

Novel method for preparing controllable and stable silver particle films for surface-enhanced Raman scattering spectroscopy

A new surface-enhanced Raman scattering (SERS) active substrate has been developed based on our previous study. Small silver nanoparticles on a quartz slide can be enlarged by using a mixture of commercially available reagents called Silver Enhancer and Initiator. The optical properties and characteristics of the new substrate have been investigated by ultraviolet-visible (UV-Vis) spectroscopy and atomic force microscopy (AFM). The results indicate that the small silver nanoparticles grow and some silver aggregates emerge on the quartz slide after the slide is immersed into the Silver Enhancer and Initiator Mixture (SEIM). The average diameter of the silver nanoparticles on the substrate becomes approximately double after the immersion into SEIM for 20 s. 1,4-bis[2-(4-pyridyl)ethenyl]-benzene (BPENB) was used as a Raman probe to evaluate the enhancement ability of the new silver substrate. It has been found that the SERS intensity can be increased about 10 times by using the substrate treated by SEIM compared with that without being treated by SEIM. Interestingly enough, the SERS enhancement increases with time. This may be due to the reorganization of silver nanoparticles on the quartz surface. The new substrate can remain active for more than 90 days. The adsorption mode of BPENB on the new substrate and the dependence of the BPENB configurations on the concentration of BPENB in methanol solution have also been investigated by SERS or UV-Vis spectroscopy. The SERS spectra of a self-assembled monolayer (SAM) BPENB film adsorbed on a silver substrate treated by SEIM show that BPENB molecules are chemically absorbed through the Ag-N bond. Consequently, a nearly perpendicular orientation of BPENB on the silver surface is proposed. The SERS spectra of BPENB SAMs on the new substrates fabricated from methanol solutions with different concentrations are compared. The concentration dependence of the SERS spectra reveals that the BPENB molecules are adsorbed on the silver film as monomers when the film is prepared from the solution with a lower concentration (<4 x 10(-6) M) and as aggregates when it is prepared from the solution with a higher concentration (>1 x 10(-5) M).     

Potential of surface-enhanced Raman spectroscopy for the rapid identification of Escherichia coli and Listeria monocytogenes cultures on silver colloidal nanoparticles

Surface-enhanced Raman (SERS) spectra of various batches of bacteria adsorbed on silver colloidal nanoparticles were collected to explore the potential of the SERS technique for rapid and routine identification of E. coli and L. monocytogenes cultures. Relative standard deviation (RSD) of SERS spectra from silver colloidal suspensions and ratios of SERS peaks from small molecules (K(3)PO(4)) were used to evaluate the reproducibility, stability, and binding effectiveness of citrate-reduced silver colloids over batch and storage processes. The results suggested consistent reproducibility of silver colloids over batch process and also stability and consistent binding effectiveness over an eight-week storage period. A variety of mixtures of E. coli/L. monocytogenes cultures with different colloidal batches revealed that, despite large variations in relative intensities and positions of SERS active bands, characteristic and unique bands at 712 and 390 cm(-1) were consistently observed and were the strongest in E. coli and L. monocytogenes cultures, respectively. Two specific bands were used to develop simple algorithms in the evaluation of binding effectiveness of silver colloids over storage and further to identify E. coli and L. monocytogenes cultures with a 100% success. A single spectrum acquisition took 5 approximately 6 min, and a minimum of 25 microL silver colloid was directly mixed with 25 microL volume of incubated bacterial culture. The short acquisition time and small volume of incubated bacterial culture make silver colloidal nanoparticle based SERS spectroscopy ideal for potential use in the routine and rapid screening of E. coli and L. monocytogenes cultures on large scales. This is the first report of the development of simple and universal algorithms for bacterial identification from the respective exclusive SERS peaks.     

Fabrication of high performance surface enhanced Raman scattering substrates by a solid-state ionics method

Silver nanostructures were prepared by a solid-state ionics method using fast ionic conductor RbAg(4)I(5) films under a direct current electric field (DCEF). The surface morphology of the silver nanostructures grown under different constant current fields was characterized by scanning electron microscopy (SEM). Rhodamine 6G (R6G) aqueous solutions were used as probe molecules to detect the Raman enhancement performance of the silver nanostructure substrates. The effect of external electric field current intensity on the surface morphology of the silver nanostructures during the preparation was studied in detail. The enhancement effect of the silver nanostructure surface enhanced Raman scattering (SERS) substrates with different surface morphologies toward R6G was determined. We found that disordered silver nanowires (DSNW), ordered silver nanowires (OSNW), densely arranged silver nanobamboo arrays (SNBA) and compactly arranged silver nanobud clusters (SNBC) were respectively obtained when the constant current intensity was 3?μA, 5?μA, 8?μA and 12?μA under the same vacuum evaporation plating conditions. The limiting concentrations of R6G for these SERS substrates were found to be 10(-7)?mol?l(-1), 10(-13)?mol?l(-1), 10(-13)?mol?l(-1) and 10(-16)?mol?l(-1), respectively.     

Surface-enhanced raman scattering (SERS) detection of low concentrations of tryptophan amino acid in silver colloid

The surface-enhanced Raman scattering (SERS) spectrum of L-tryptophan has been studied in the concentration range 1.4 × 10(-8) to 5 × 10(-4) M. A borohydride-reduced silver colloid was employed as the nanoparticle enhancing agent and different electrolytes have been tested for activation of the colloid. The optimum conditions have been determined for achieving high sensitivity of detection. The experimental procedure developed, which includes the use of a composite electrolyte (a mixture of NaHCO(3) and NaCl) for colloid activation, results in very high enhancement of the Raman signal (up to 10(8)). This gives the possibility of studying SERS spectra of L-tryptophan at concentrations as low as 10(-8) M, which is several orders of magnitude lower than previously reported in the literature. The observed SERS spectra were very reproducible and were detectable 2 minutes after mixing, reaching maximum strength approximately 15 minutes after mixing. The spectral characteristics were stable over the entire period of observation. We have found that SERS spectra of tryptophan in silver colloid differ in several features at low (below ～10(-5) M) and at high (above ～10(-4) M) concentrations. The most important difference is the absence of the peak near 1000 cm(-1) at low concentrations, which is usually assigned to the indole ring breathing mode. The observed spectra allow us to suggest that at low concentrations Trp molecules bind to the surface through the indole ring, which remains flat on the surface. This is in contrast to the previously reported observation of SERS spectra from Trp performed at concentration levels above 10(-5) M.     

Gold nanoparticle-based pH sensor in highly alkaline region at pH > 11: surface-enhanced Raman scattering study

A surface plasmon resonance spectroscopy study showed that citrate-reduced gold nanoparticles ( approximately 15 nm diameter, approximately 9 x 10(-9) M concentration, approximately 2 x 10(-2) M ionic strength) were found to be utilized as a colorimetric sensor by exhibiting a distinct color change at a highly alkaline pH > 11.5. Surface-enhanced Raman scattering (SERS) of 4-ethynylpyridine (4-EP) on gold nanoparticle surfaces indicated that the multiple peaks in the v(C identical withC) stretching bands should vary significantly in the highly alkaline region from pH 12 to 14. As the pH value increased, the v(C identical withC) stretching band intensity at approximately 2080 cm(-1) became stronger than that at approximately 2010 cm(-1). The pK(1/2) value was determined to be around 13 by the SERS titration of taking intensity ratios of I(2080) with respect to I(2010). Using SERS enhancements and conspicuous spectral changes, self-assembled monolayers (SAMs) of 4-EP on Au nanoparticles holds potential as a pH sensor for sensitive detection of the hydroxide OH(-) concentration at around pH 13 in an aqueous solution. The pH calibration from SERS titration of 4-EP is expected to have advantages in terms of higher alkaline detection limit and more precise measurements, if compared with the indigo carmine, the pK(1/2) value of which is 12.2.     

Adsorption of S-S containing proteins on a colloidal silver surface studied by surface-enhanced Raman spectroscopy

We present a Raman and surface-enhanced Raman scattering (SERS) study of the following proteins containing S-S group(s): alpha chymotrypsin (alpha-CHT), insulin, lysozyme, oxytocin (OXT), Streptomyces subtilisin inhibitor (SSI), and trypsin inhibitor (STI). The SERS study is performed in order to understand the adsorption mechanism of the above-mentioned proteins on a colloidal silver surface. The SERS spectra presented here show bands associated mainly with aromatic amino acid vibrations. In addition, two distinct vibrations of the -C-S-S-C- fragment are observed in the Raman and SERS spectra, i.e., nu(SS) and nu(CS). The enhancement of the nu(SS) vibration in the SERS spectra yields evidence that the intact disulfide bridge(s) is (are) located near the silver surface. This finding is supported by the presence of the nu(CS) mode(s). The presence of nus(COO-) and nu(C-COO-) in the SERS spectra in the 1384-1399 cm(-1) and 909-939 cm(-1) regions, respectively, indicate that the negatively charged COO- groups (aspartic and glutamic acids) assist in the binding on the positively charged silver surface. The Raman amide I and III bands observed in the 1621-1633 and 1261-1289 cm(-1) ranges, respectively, indicate that the alpha-helical conformation is favored for binding to the surface over the random coil or beta-sheet conformations. In addition, the presence of the imino group of Trp and/or His indicates that these amino acid residues may also bind to the silver sol.     

Chitosan-coated anisotropic silver nanoparticles as a SERS substrate for single-molecule detection

Surface-enhanced Raman spectroscopy (SERS) is a technique that has become widely used for identifying and providing structural information about molecular species in low concentration. There is an ongoing interest in finding optimum particle size, shape and spatial distribution for optimizing the SERS substrates and pushing the sensitivity toward the single-molecule detection limit. This work reports the design of a novel, biocompatible SERS substrate based on small clusters of anisotropic silver nanoparticles embedded in a film of chitosan biopolymer. The SERS efficiency of the biocompatible film is assessed by employing Raman imaging and spectroscopy of adenine, a significant biological molecule. By combining atomic force microscopy with SERS imaging we find that the chitosan matrix enables the formation of small clusters of silver nanoparticles, with junctions and gaps that greatly enhance the Raman intensities of the adsorbed molecules. The study demonstrates that chitosan-coated anisotropic silver nanoparticle clusters are sensitive enough to be implemented as effective plasmonic substrates for SERS detection of nonresonant analytes at the single-molecule level.     

Quantitative analysis of double-stranded DNA amplified by a polymerase chain reaction employing surface-enhanced Raman spectroscopy

Surface-enhanced Raman spectroscopy (SERS) was utilized for the quantitative analysis of double-stranded (ds) DNA amplified by a polymerase chain reaction (PCR). 4?, 6-Diamidino-2-phenylindole dihydrochloride (DAPI), which intercalates into ds-DNA but does not form a complex with single-stranded (ss) DNA, was added to a DNA solution after amplification by PCR. When the solution was mixed, including ds-DNA-DAPI complexes and free DAPI with silver colloid sol, only free DAPI was adsorbed on the colloid surface. The dye on the colloid gave very intense SERS signals with excitation at 514.5 nm, whereas DAPI engaging in the intercalation with ds-DNA did not show any SERS signal. The SERS spectrum of DAPI on the colloid showed a strong band at 1610 cm(-1) due to the C?N stretching mode, and a linear relationship was observed between the peak intensity of the C?N stretching band and the concentration of free DAPI. Therefore one can determine the concentration of free DAPI by the SERS measurement. The more ds-DNA there is in the solution, the less free DAPI there is. Thus it is possible to quantitatively analyze the ds-DNA amplified by PCR indirectly by using SERS. The correlation coefficient between the peak intensity of the C?N stretching band and the concentration of ds-DNA amplified by PCR was calculated to be 0.988 for a concentration range from 0.1 to 1.3 mg/ml.     

Cover Picture: Metal–Silica Hybrid Nanostructures for Surface‐Enhanced Raman Spectroscopy (Adv. Mater. 21/2006)

The image shows an ordered array of silver‐tipped silica nanorods, which serve as a substrate for surface enhanced Raman spectroscopy (SERS). Signal intensities from test molecules in regions of aggregated pillars (indicated by the green laser beam) were enhanced by factors of 10 to 20 compared to arrays of separated pillars, as reported by Moskovits and co‐workers on p. 2829. This hybrid structure maximizes SERS signal intensities from analytes while minimizing the quantities needed for detection due to the precise formation of “hot regions” at the intersection of the silver tips.     

Single-molecule detection using surface-enhanced resonance Raman scattering and Langmuir-Blodgett monolayers

The Langmuir-Blodgett (LB) technique has been used to obtain spatially resolved surface-enhanced resonance Raman scattering (SERRS) spectra of single dye molecules dispersed in the matrix of a fatty acid. The experimental results presented here mimic the original electrochemical surface-enhanced Raman scattering (SERS) work where the background bulk water did not interfere with the detection of the SERS signal of molecules adsorbed onto the rough silver electrode. LB monolayers of the dye in fatty acid have been fabricated on silver island films with a concentration, in average, of one probe molecule per micrometer square. The properties of single-molecule spectroscopy were investigated using micro-Raman including mapping and global images. Blinking of the SERRS signal was also observed.     

Surface-enhanced Raman spectra of calf thymus DNA adsorbed on concentrated silver colloid

Raman and surface-enhanced Raman scattering (SERS) spectra of calf thymus DNA were investigated. We have carried out improvements to the silver colloid preparation method of Lee and Meisel in two respects. In one method, the silver sol was boiled with rapid stirring for over two hours. In the second method, the silver sol was concentrated by centrifugation before adding it to the DNA solution. The resulting hydrosol could be stored for 15 months because of its high stabilization. Structural information with respect to the phosphate backbone, deoxyribose, and four bases of DNA could be obtained before and after the DNA solutions were added to the concentrated Ag colloid substrate. The intensities of almost all characteristic bands assigned to various groups of the components of DNA were enhanced to a remarkable degree. The enhancement effect of the DNA solution at neutral pH 7.0 was obviously much better than that at acidic pH 3.4 or at alkaline pH 8.5. Intensity increases of the SERS bands of the DNA solution with time were observed. The SERS signals obtained 16 hours after the interaction of the Ag colloid with the DNA solution were much better than the SERS signals obtained just after the mixed liquid was prepared. This method can be widely used to store the Ag colloid for long times and to obtain the SERS spectra of DNA molecules, and it can further be used to study the adsorption behavior of solute biomacromolecules in different solvents.     

Surface-enhanced Raman spectroscopy of soft-landed polyatomic ions and molecules

Surface-enhanced Raman spectroscopy (SERS) was used to detect and characterize polyatomic cations and molecules that were electrosprayed into the gas phase and soft-landed in vacuum on plasma-treated silver substrates. Organic dyes such as crystal violet and Rhodamine B, the nucleobase cytosine, and nucleosides cytidine and 2'-deoxycytidine were immobilized by soft landing on plasma-treated metal surfaces at kinetic energies ranging from near thermal to 200 eV. While enhancing Raman scattering 10(5)-10(6)-fold, the metal surface effectively quenches the fluorescence that does not interfere with the Raman spectra. SERS spectra from submonolayer amounts of soft-landed compounds were sufficiently intense and reproducible to allow identification of Raman active vibrational modes for structure assignment. Soft-landed species appear to be microsolvated on the surface and bound via ion pairing or pi-complexation to the Ag atoms and ions in the surface oxide layer. Comparison of spectra from soft-landed and solution samples indicates that the molecules survive soft landing without significant chemical damage even when they strike the surface at hyperthermal collision energies.     

Silver-coated dye-embedded silica beads: a core material of dual tagging sensors based on fluorescence and Raman scattering

We have developed a new type of dual-tag sensor for immunoassays, operating via both fluorescence and surface-enhanced Raman scattering (SERS). A one-shot fluorescence image over the whole specimen allows us to save considerable time because any unnecessary time-consuming SERS measurements can be avoided from the signature of the fluorescence. Dye-embedded silica beads are prepared initially, and then SERS-active silver is coated onto them via a very simple electroless-plating method. The Raman markers are subsequently assembled onto the Ag-coated silica beads, after which they are stabilized by silanization via a biomimetic process in which a poly(allylamine hydrochloride) layer formed on the Raman markers by a layer-by-layer deposition method acting as a scaffold for guiding silicification. In the final stage, specific antibodies are attached to the silica surface in order to detect target antigens. The fluorescence signal of the embedded dye can be used as a fast readout system of molecular recognition, whereas the SERS signals are subsequently used as the signature of specific molecular interactions. In this way, the antibody-grafted particles were found to recognize antigens down to 1 × 10(-10) g mL(-1) solely by the SERS peaks of the Raman markers.     

Surface-enhanced Raman spectroscopy studies of orderly arranged silica nanospheres-synthesis,characterization and dye detection

Silica nanospheres have been explored much for drug delivery, photocatalysis, sensors and energy storage applications. It also acts as a template for Surface-Enhanced Raman Spectroscopy (SERS) substrates. Uniform nanostructures at low cost with high reproducibility are the major challenges in SERS substrate fabrication. In the present work, silica nanospheres were synthesized using stober method and deposited on to glass slides using Vertical deposition techniques. Different size/thickness of Silver (Ag) nanoparticles were deposited onto silica thin films using sputter deposition technique. The monodispersity of silica nanospheres and size of silver nanoparticles (10 nm, 20 nm and 30 nm) were confirmed by FESEM analysis. The structural properties were confirmed through XRD. UV–Vis analysis revealed that the plasmonic properties of Ag@SiO₂ give high surface plasmons for 30 nm thickness of silver. The binding energy of Ag@SiO₂ confirmed through XPS spectrum. The fabricated SERS substrates were used to detect Rhodamine 6G (R6G), Methylene blue (MB), Methylene violet (MV) and Methyl orange dyes as an analyte molecule with a limit of detection at about 10^?11 mol/L. The addition of SiO₂ nanospheres decreases the Ag oxidation rate and increases their stability. The maximum enhancement factor (1.5?×?10⁷) achieved for 30nm thickness of Ag@SiO₂. The results and technique establish the potential applications and reproducible SERS substrate.

     

Plasmonic dimer antennas for surface enhanced Raman scattering

Electron beam induced deposition (EBID) has recently been developed into a method to directly write optically active three-dimensional nanostructures. For this purpose a metal-organic precursor gas (here dimethyl-gold(III)-acetylacetonate) is introduced into the vacuum chamber of a scanning electron microscope where it is cracked by the focused electron beam. Upon cracking the aforementioned precursor gas, 3D deposits are realized, consisting of gold nanocrystals embedded in a carbonaceous matrix. The carbon content in the deposits hinders direct plasmonic applications. However, it is possible to activate the deposited nanostructures for plasmonics by coating the EBID structures with a continuous silver layer of a few nanometers thickness. Within this silver layer collective motions of the free electron gas can be excited. In this way, EBID structures with their intriguing precision at the nanoscale have been arranged in arrays of free-standing dimer antenna structures with nanometer sized gaps between the antennas that face each other with an angle of 90°. These dimer antenna ensembles can constitute a reproducibly manufacturable substrate for exploiting the surface enhanced Raman effect (SERS). The achieved SERS enhancement factors are of the order of 10? for the incident laser light polarized along the dimer axes. To prove the signal enhancement in a Raman experiment we used the dye methyl violet as a robust test molecule. In future applications the thickness of such a silver layer on the dimer antennas can easily be varied for tuning the plasmonic resonances of the SERS substrate to match the resonance structure of the analytes to be detected.     

Determination of pyrimidine and purine bases by reversed-phase capillary liquid chromatography with at-line surface-enhanced Raman spectroscopic detection employing a novel SERS substrate based on ZnS/CdSe silver-quantum dots

We have developed a new SERS substrate based on the reduction of silver nitrate in the presence of ZnS-capped CdSe quantum dots. This substrate showed higher sensitivities as compared to a hydroxylamine-reduced silver sol. On the basis of this new substrate, at-line SERS detection was coupled with capillary liquid chromatography (cap-LC) for the separation and selective determination of pyrimidine and purine bases. For this purpose, wells of a dedicated microtiter plate were loaded with 20 μL of the SERS substrate and placed on an automated x,y translation stage. A flow-through microdispenser capable of ejecting 50 pL droplets, at a frequency 100 Hz, was used as the interface to connect the cap-LC system to the wells loaded with SERS substrate. A detailed study of the dependence of both the separation and the surface-enhanced Raman spectra of each base on the pH was performed to optimize the system for maximum sensitivity and selectivity. Highly satisfactory analytical figures of merit were obtained for the six investigated bases (cytosine, xanthine, hypoxanthine, guanine, thymine, and adenine) with detection limits ranging between 0.2 and 0.3 ng injected on the capillary LC column, and the precisions were in the range of 3.0-6.3%.     

Room temperature aqueous synthesis of bipyramidal silver nanostructures

The proposed strategy demonstrates a simple method to synthesize the pentagonal right bipyramidal silver nanostructures in aqueous phase at room temperature. Aqueous synthesis enables the materials for direct use in biological systems. The sharp edges of silver nanostructures multiply SERS (surface enhanced Raman spectroscopy) signals by many folds. We have explored a combination of a cationic surfactant, namely, cetyl tri-methyl ammonium bromide (CTAB) and a well-known polymer, polyvinyl pyrrolidone (PVP) for capping preferential crystallographic facets of silver nanosurface. The structural transformation of these anisotropic nanostructures was studied by following various factors, such as, effect of Ag seed concentration, the ratio of concentration of CTAB to the concentration of silver nitrate, the effect of PVP, the ascorbic acid concentration dependence and the effect of pH. CTAB functions as template directing agent while PVP acts as a shape directing agent. Zeta potential measurements and Fourier Transform Infra-red (FTIR) spectral analysis reveal that PVP substitutes CTAB over the facets of silver nanobypiramids.     

Raman spectroscopic detection for perchlorate at low concentrations

Perchlorate (ClO4-) has recently emerged as a widespread environmental contaminant found in groundwater and surface water, and there is a great need for rapid detection and monitoring of this contaminant. In this study, we explore the use of surface-enhanced (SERS) and normal Raman spectroscopy for detecting ClO4- at low concentrations. We found that ClO4- is SERS active and, for the first time, were able to detect ClO4- at concentrations as low as 10(-6)-10(-7) M (or 10-100 microg/L) through the application of silver SERS substrates or selective sorbents such as bifunctional anion-exchange resins. The use of selective sorbents greatly enhanced the reproducibility and sensitivity of ClO4- detection by normal Raman spectroscopy. Further exploration and research may allow application of these techniques for in situ, real-time detection and monitoring of ClO4- in environmental samples at even lower concentrations.