基于扰动观测器的永磁同步电机电流环自适应滑模控制

针对扰动对永磁同步电机转速伺服系统性能的影响,提出了基于扰动观测器的电流环自适应滑模控制方法。设计了自适应律在线估计系统的内部参数摄动以补偿模型不确定性扰动。同时,设计了滑模扰动观测器实时估计系统外部负载扰动,并将观测值前馈补偿到电流环自适应滑模控制器,在提高系统鲁棒性的同时降低滑模控制系统的抖振。实验结果显示,采用基于扰动观测器的电流环自适应滑模控制方法,系统可快速、准确、无超调地跟踪900r/min的速度指令,调节时间为0.08s,稳态误差为±5r/min。加入0.6N·m的负载扰动,该控制方法的最大转速波动为21r/min,比PI控制方法的转速波动减小了3.4%。仿真和实验结果表明,基于扰动观测器的电流环自适应控制方法提高了永磁同步电机转速伺服系统的鲁棒性和动态响应性能,同时可有效抑制滑模控制系统的抖振。     

Adaptive terminal sliding-mode control strategy for DC-DC buck converters

This paper presents an adaptive terminal sliding mode control (ATSMC) strategy for DC-DC buck converters. The idea behind this strategy is to use the terminal sliding mode control (TSMC) approach to assure finite time convergence of the output voltage error to the equilibrium point and integrate an adaptive law to the TSMC strategy so as to achieve a dynamic sliding line during the load variations. In addition, the influence of the controller parameters on the performance of closed-loop system is investigated. It is observed that the start up response of the output voltage becomes faster with increasing value of the fractional power used in the sliding function. On the other hand, the transient response of the output voltage, caused by the step change in the load, becomes faster with decreasing the value of the fractional power. Therefore, the value of fractional power is to be chosen to make a compromise between start up and transient responses of the converter. Performance of the proposed ATSMC strategy has been tested through computer simulations and experiments. The simulation results of the proposed ATSMC strategy are compared with the conventional SMC and TSMC strategies. It is shown that the ATSMC exhibits a considerable improvement in terms of a faster output voltage response during load changes.     

Robust adaptive precision motion control of hydraulic actuators with valve dead-zone compensation

This paper addresses the high performance motion control of hydraulic actuators with parametric uncertainties, unmodeled disturbances and unknown valve dead-zone. By constructing a smooth dead-zone inverse, a robust adaptive controller is proposed via backstepping method, in which adaptive law is synthesized to deal with parametric uncertainties and a continuous nonlinear robust control law to suppress unmodeled disturbances. Since the unknown dead-zone parameters can be estimated by adaptive law and then the effect of dead-zone can be compensated effectively via inverse operation, improved tracking performance can be expected. In addition, the disturbance upper bounds can also be updated online by adaptive laws, which increases the controller operability in practice. The Lyapunov based stability analysis shows that excellent asymptotic output tracking with zero steady-state error can be achieved by the developed controller even in the presence of unmodeled disturbance and unknown valve dead-zone. Finally, the proposed control strategy is experimentally tested on a servovalve controlled hydraulic actuation system subjected to an artificial valve dead-zone. Comparative experimental results are obtained to illustrate the effectiveness of the proposed control scheme.     

Adaptive sliding mode disturbance rejection control with prescribed performance for robotic manipulators

This study proposes an adaptive sliding mode disturbance rejection control with prescribed performance for robotic manipulators. A transformation with respect to tracking error using certain performance functions is used to ensure the transient and steady-state performances of the trajectory tracking control for robotic manipulators. Using the transformed error, a nonsingular terminal sliding mode surface is proposed. A continuous terminal sliding mode control (SMC) is presented to stabilize the system. To compensate for the uncertainty and external disturbance, a novel sliding mode disturbance observer is proposed. Considering the unknown boundary of the derivative of a lumped disturbance, an adaptive law based on the idea of equivalent control is designed. Combining the adaptive law, continuous nonsingular terminal SMC, and sliding mode disturbance observer, the adaptive sliding mode disturbance rejection control with prescribed performance is developed. Simulations are carried out to demonstrate the effectiveness of the proposed approach.     

Adaptive fast sliding mode fault tolerant control integrated with disturbance observer for spacecraft attitude stabilization system

In this paper, the problem of fault-tolerant control (FTC) for spacecraft attitude stabilization system with actuator fault and mismatched disturbance is investigated. A novel fault tolerant control strategy based on adaptive fast terminal sliding mode control (AFTSMC) is proposed. Firstly, a novel composite observer is proposed to estimate the disturbance, actuator efficiency factor and partial states of the system. By introducing a sliding mode observer, the bias actuator fault is reconstructed. Subsequently, in accordance with the estimated information, a novel sliding mode fault tolerant controller is designed. The proposed control scheme contains two compensators and two adaptive parameters to attenuate the mismatched disturbance, to compensate actuator fault, and to guarantee fast convergence of the system. Furthermore, the reachability of sliding motion is proved. The simulation results for the spacecraft system illustrate the effectiveness of the proposed method.     

Adaptive fuzzy wavelet network control of second order multi-agent systems with unknown nonlinear dynamics

In this paper, consensus problem is considered for second order multi-agent systems with unknown nonlinear dynamics under undirected graphs. A novel distributed control strategy is suggested for leaderless systems based on adaptive fuzzy wavelet networks. Adaptive fuzzy wavelet networks are employed to compensate for the effect of unknown nonlinear dynamics. Moreover, the proposed method is developed for leader following systems and leader following systems with state time delays. Lyapunov functions are applied to prove uniformly ultimately bounded stability of closed loop systems and to obtain adaptive laws. Three simulation examples are presented to illustrate the effectiveness of the proposed control algorithms.     

Adaptive robust motion trajectory tracking control of pneumatic cylinders with LuGre model-based friction compensation

Friction compensation is particularly important for motion trajectory tracking control of pneumatic cylinders at low speed movement. However, most of the existing model-based friction compensation schemes use simple classical models, which are not enough to address applications with high-accuracy position requirements. Furthermore, the friction force in the cylinder is time-varying, and there exist rather severe unmodelled dynamics and unknown disturbances in the pneumatic system. To deal with these problems effectively, an adaptive robust controller with LuGre model-based dynamic friction compensation is constructed. The proposed controller employs on-line recursive least squares estimation（RLSE） to reduce the extent of parametric uncertainties, and utilizes the sliding mode control method to attenuate the effects of parameter estimation errors, unmodelled dynamics and disturbances. In addition, in order to realize LuGre model-based friction compensation, the modified dual-observer structure for estimating immeasurable friction internal state is developed. Therefore, a prescribed motion tracking transient performance and final tracking accuracy can be guaranteed. Since the system model uncertainties are unmatched, the recursive backstepping design technology is applied. In order to solve the conflicts between the sliding mode control design and the adaptive control design, the projection mapping is used to condition the RLSE algorithm so that the parameter estimates are kept within a known bounded convex set. Finally, the proposed controller is tested for tracking sinusoidal trajectories and smooth square trajectory under different loads and sudden disturbance. The testing results demonstrate that the achievable performance of the proposed controller is excellent and is much better than most other studies in literature. Especially when a 0.5 Hz sinusoidal trajectory is tracked, the maximum tracking error is 0.96 mm and the average tracking error is 0.45 mm. This paper constructs an adaptive robust controller     

Adaptive nonlinear robust relative pose control of spacecraft autonomous rendezvous and proximity operations

This paper studies relative pose control for a rigid spacecraft with parametric uncertainties approaching to an unknown tumbling target in disturbed space environment. State feedback controllers for relative translation and relative rotation are designed in an adaptive nonlinear robust control framework. The element-wise and norm-wise adaptive laws are utilized to compensate the parametric uncertainties of chaser and target spacecraft, respectively. External disturbances acting on two spacecraft are treated as a lumped and bounded perturbation input for system. To achieve the prescribed disturbance attenuation performance index, feedback gains of controllers are designed by solving linear matrix inequality problems so that lumped disturbance attenuation with respect to the controlled output is ensured in the L₂-gain sense. Moreover, in the absence of lumped disturbance input, asymptotical convergence of relative pose are proved by using the Lyapunov method. Numerical simulations are performed to show that position tracking and attitude synchronization are accomplished in spite of the presence of couplings and uncertainties.     

随动系统的新型非奇异快速终端滑模控制

鉴于某舰载随动系统存在摩擦、海况等扰动因素,为提升系统控制精度及鲁棒性,提出了一种基于相位补偿的非奇异快速终端滑模控制(NFTSM+ARBF+TTD)方法.将泰勒公式与非线性函数fhan相结合,构造跟踪微分器,旨在减小相位延迟.在抑制微分过程噪声的基础上,应用泰勒公式进行相位补偿.设计自适应神经网络(ARBF)逼近扰动...     

基于模糊干扰观测器的电动Stewart平台自适应模糊控制

建立了一个电动Stewart平台的统一动力学模型,并基于它设计了一种新型的自适应模糊控制算法。这个统一的动力学模型在任务空间中使用了Newton-Euler方法建立,同时结合了平台动力学和执行器动力学模型。自适应模糊控制算法使用计算力矩方法设计运动平台标称模型的逆动力学控制器,然后使用基于模糊干扰观测器的自适应模糊控制器对模型的不确定性和外部扰动进行补偿。通过数值仿真分析表明,在不引入高增益控制器的情况下,成功地消除了平台参数的不确定性和外部干扰的影响,保证了平台的跟踪性能。     

A new robust control for minirotorcraft unmanned aerial vehicles

This paper presents a new robust control based on finite-time Lyapunov stability controller and proved with backstepping method for the position and the attitude of a small rotorcraft unmanned aerial vehicle subjected to bounded uncertainties and disturbances. The dynamical motion equations are obtained by the Newton–Euler formalism. The proposed controller combines the advantage of the backstepping approach with finite-time convergence techniques to generate a control laws to guarantee the faster convergence of the state variables to their desired values in short time and compensate for the bounded disturbances. A formal proof of the closed-loop stability and finite-time convergence of tracking errors is derived using the Lyapunov function technique. Simulation results are presented to corroborate the effectiveness and the robustness of the proposed control method.     

Precision motion control of permanent magnet linear motors

In the paper, a method of precision motion control for permanent magnet linear motors is proposed. Unlike rotational motors, permanent magnetic linear motors are more sensitive to various force disturbances because of the reduction of gears. So, as a feedback compensator, a disturbance observer is used to compensate the force disturbances based on the disturbance model. But the force disturbances of permanent magnetic linear motors cannot be fully compensated owing to the error of dynamic model, inaccurately detected velocity and acceleration, especially when a permanent magnetic linear motor runs in low speed. Further analysis shows that the force ripple is the main force disturbance when the velocity of a PMLM is close to zero, and the disturbance model denotes that the force ripple is position dependent. In order to further suppress the force disturbances of permanent magnetic linear motors a feedforward neural network using the BP algorithm is proposed to approximate and compensate the force ripple. The experimental results show that the force ripple is efficiently alleviated and the high positioning precision can be achieved by using the proposed precision motion control method.     

基于自适应模糊神经网络辨识的电液伺服系统L2增益设计

为克服电液伺服系统不确定性、非线性、估计误差和干扰等因素对系统稳定性和精度的影响，提出了基于自适应模糊神经网络辨识的电液伺服系统L2增益设计方法。用自适应模糊神经网络在线估计包括系统不确定性和非线性在内的未知动态特性，同时用增益自适应变结构补偿自适应模糊神经网络的估计误差，用系统L2增益设计方法抑制干扰对系统的影响，以期使系统对不确定性和非线性具有鲁棒性，而且从干扰到描述系统跟踪误差的评价函数的L2增益小于指定值。     

Multivariable robust adaptive sliding mode control of an industrial boiler–turbine in the presence of modeling imprecisions and external disturbances: A comparison with type-I servo controller

To guarantee the safety and efficient performance of the power plant, a robust controller for the boiler–turbine unit is needed. In this paper, a robust adaptive sliding mode controller (RASMC) is proposed to control a nonlinear multi-input multi-output (MIMO) model of industrial boiler–turbine unit, in the presence of unknown bounded uncertainties and external disturbances. To overcome the coupled nonlinearities and investigate the zero dynamics, input–output linearization is performed, and then the new decoupled inputs are derived. To tackle the uncertainties and external disturbances, appropriate adaption laws are introduced. For constructing the RASMC, suitable sliding surface is considered. To guarantee the sliding motion occurrence, appropriate control laws are constructed. Then the robustness and stability of the proposed RASMC is proved via Lyapunov stability theory. To compare the performance of the purposed RASMC with traditional control schemes, a type-I servo controller is designed. To evaluate the performance of the proposed control schemes, simulation studies on nonlinear MIMO dynamic system in the presence of high frequency bounded uncertainties and external disturbances are conducted and compared. Comparison of the results reveals the superiority of proposed RASMC over the traditional control schemes. RAMSC acts efficiently in disturbance rejection and keeping the system behavior in desirable tracking objectives, without the existence of unstable quasi-periodic solutions.     

Indirect adaptive fuzzy wavelet neural network with self- recurrent consequent part for AC servo system

This paper proposes a novel indirect adaptive fuzzy wavelet neural network (IAFWNN) to control the nonlinearity, wide variations in loads, time-variation and uncertain disturbance of the ac servo system. In the proposed approach, the self-recurrent wavelet neural network (SRWNN) is employed to construct an adaptive self-recurrent consequent part for each fuzzy rule of TSK fuzzy model. For the IAFWNN controller, the online learning algorithm is based on back propagation (BP) algorithm. Moreover, an improved particle swarm optimization (IPSO) is used to adapt the learning rate. The aid of an adaptive SRWNN identifier offers the real-time gradient information to the adaptive fuzzy wavelet neural controller to overcome the impact of parameter variations, load disturbances and other uncertainties effectively, and has a good dynamic. The asymptotical stability of the system is guaranteed by using the Lyapunov method. The result of the simulation and the prototype test prove that the proposed are effective and suitable.     

基于压电智能结构状态估计误差补偿的自抗扰振动控制

压电智能结构的模型难以精确建立,且存在外界环境激励干扰和内部参数不确定等问题,从而影响闭环结构的振动控制性能。基于此,将结构的内部干扰和外界激励的影响归结为系统的集总干扰,并利用扩张状态观测器(Extended state observer,ESO)设计不依赖于模型的自抗扰振动控制器。然而当外界扰动激励变化时,扩张状态观测器对扰动和各阶状态的估计不可避免存在偏差,难以保证振动控制的效果。为克服二阶自抗扰策略在振动主动控制中的不足,提出一种基于压电智能板结构的状态估计误差补偿自抗扰振动控制方案。利用状态观测误差信息,对二阶自抗扰控制器进行补偿,从而减小ESO对扰动和各阶状态估计的压力,提高振动控制效果。利用dSPACE实时仿真系统,搭建四面固支压电智能板结构的振动主动试验平台。四种干扰激励的试验结果验证该方法的有效性、实用性和强抗干扰能力。     

On the rejection of internal and external disturbances in a wind energy conversion system with direct-driven PMSG

This paper deals with the critical issue in a wind energy conversion system (WECS) based on a direct-driven permanent magnet synchronous generator (PMSG): the rejection of lumped disturbance, including the system uncertainties in the internal dynamics and unknown external forces. To simultaneously track the motor speed in real time and capture the maximum power, a maximum power point tracking strategy is proposed based on active disturbance rejection control (ADRC) theory. In real application, system inertia, drive torque and some other parameters change in a wide range with the variations of disturbances and wind speeds, which substantially degrade the performance of WECS. The ADRC design must incorporate the available model information into an extended state observer (ESO) to compensate the lumped disturbance efficiently. Based on this principle, a model-compensation ADRC is proposed in this paper. Simulation study is conducted to evaluate the performance of the proposed control strategy. It is shown that the effect of lumped disturbance is compensated in a more effective way compared with the traditional ADRC approach.     

Adaptive compensation control for attitude adjustment of quad-rotor unmanned aerial vehicle

A compensation control strategy based on adaptive back-stepping technique is presented to address the problem of attitude adjustment for a quad-rotor unmanned aerial vehicle (QR- UAV) with inertia parameter uncertainties, the limited airflow disturbance and the partial loss of rotation speed effectiveness. In the design process of control system, adaptive estimation technique is introduced into the closed loop system in order to compensate the lumped disturbance term. More specifically, the designed controller utilizes “prescribed performance bounds” method, and therefore guarantees the transient performance of tracking errors, even in the presence of the lumped disturbance. Adaptive compensation algorithms under the proposed closed loop system structure are derived in the sense of Lyapunov stability analysis such that the attitude tracking error converge to a small neighborhood of equilibrium point. Finally, the simulation results demonstrate the effectiveness of the proposed controller.     

通过直线伺服鲁棒跟踪控制方法提高轮廓加工精度

为了减小零件加工的轮廓误差,提出了一种采用直线伺服驱动的零相位跟踪控制器(ZPETC)和干扰观测器 (DOB)相结合的鲁棒跟踪控制策略。零相位误差跟踪控制器作为前馈跟踪控制器,提高了快速性,使系统实现准确跟踪;基于干扰观测器的鲁棒反馈控制器补偿了外部扰动、未建模动态、系统参数变化和机械非线性等不确定因素,并根据预测到的干扰信息对各轴进行补偿以消除干扰对系统的影响,从而保证了系统的强鲁棒性能。仿真结果表明所提出的控制方案是有效的,既能实现完好跟踪,又有较强的鲁棒性能,从而提高了轮廓加工精度。