Proposal of rectifier type superconducting fault current limiter with non-inductive reactor (SFCL)

A rectifier type superconducting fault current limiter (SFCL) with non-inductive reactor has been proposed. The concept behind this SFCL is the appearance of high impedance during non-superconducting state of the coil. In a hybrid bridge circuit, two superconducting coils connected in anti-parallel: a trigger coil and a limiting coil. Both the coils are magnetically coupled with each other and have same number of turns. There is almost zero flux inside the core and therefore the total inductance is small during normal operation. At fault time when the trigger coil current reaches to a certain level, the trigger coil changes from superconducting state to normal state. This super-to-normal transition of the trigger coil changes the current ratio of the coils and therefore the flux inside the reactor is no longer zero. So, the equivalent impedance of both the coils increased thus limits the fault current. We have carried out computer simulation using EMTDC and observed the results. A preliminary experiment has already been performed using copper wired reactor with simulated super-to-normal transition resistance and magnetic switches. Both the simulation and preliminary experiment shows good results. The advantage of using hybrid bridge circuit is that the SFCL can also be used as circuit breaker. Two separate bridge circuit can be used for both trigger coil and the limiter coil. In such a case, the trigger coil can be shutdown immediately after the fault to reduce heat and thus reduce the recovery time. Again, at the end of fault when the SFCL needs to re-enter to the grid, turning off the trigger circuit in the two-bridge configuration the inrush current can be reduced. This is because the current only flows through the limiting coil. Another advantage of this type of SFCL is that no voltage sag will appear during load increasing time as long as the load current stays below the trigger current level.     

Experimental analysis of AC loss and recovery characteristics for proposal of effective thickness of spacers in pancake type

For the design of superconducting fault current limiter, the research about recovery time and AC loss is essential issue because this characteristic is closely related to stability and efficiency. In general, superconducting fault current limiter (SFCL) modules can be made into pancake or solenoid type coil. While the pancake type coil has smaller AC loss, it has longer recovery time compared with the solenoid type coil. In this paper, a new pancake type coil was proposed to decrease recovery time by improving their cryogenic condition. A new pancake type coil is made with spacers between adjacent superconducting tapes. However, as the thickness of the spacer was increased, the AC loss was increased unlike the recovery characteristic. From the experimental results, our group confirmed that the pancake type coil with the spacer has trade-off relationship between AC loss and recovery characteristics with the spacer thickness.The proposed results in this paper would be utilized to design superconducting fault current limiters.     

Recovery estimation for over-current test of non-inductive fault current limiters using numerical analysis

When an HTS coated conductor (CC) is used as a conductor of a superconducting fault current limiter (SFCL), the CC is expected to be exposed to the over-current and temperature of the CC is expected to be increased rapidly by electrical joule heating. Because the CC is a composite tape, thermal and electrical properties of composite materials could affects over-current limiting capacity and recovery time of SFCL. This paper presents experimental and numerical results of over-current test and recovery time measurement test on four bifilar wound SFCL modules. The temperature transitions of the samples were estimated from total electrical resistance of the coils. We fabricated one bifilar solenoid coil and three bifilar pancake coils whose cryogenic conditions were different from the other coils. An numerical model was also fabricated to simulate the temperature transition and the numerical results were compared with experimental results.     

Development,Updating and Long-Term Operations of a 10.5 kV HTS Fault Current Limiter

There are many irreplaceable advantages of high temperature superconducting (HTS) fault current limiter, applying in electric utilities. It is expected to be able to solve excessive fault current problems and to enhance safety and stability of power systems. In this paper, the R and D of an improved bridge-type 10.5 kV three-phase superconducting fault current limiter (SFCL) was present. Each phase adopted a HTS coil with inductance of 6.2 mH. The three coils wound with 8,571 m Bi2223/Ag tapes totally. After installation at a 110 kV/10.5 kV substation in Hunan Province of China, the performances of the whole SFCL were tested, including a three-phase-to-ground short circuit experiment at the pre-setup short circuit point. And then, the SFCL was put into operations in the 10.5 kV power grids for more than 11000 h. About 3 years later, the SFCL was moved, reinstalled, and put into operation again since February 16 of 2011 at a 10.5-kV superconducting power substation located in Baiyin, Gansu Province of China. In this paper, the redesigned and manufactured cryostats with nonmagnetic stainless steel, tests, and long-term operations of the SFCL in 10.5 kV power grids were also described in detail.     

Surface flashover characteristics in liquid nitrogen for application of superconducting pancake coils

For the development of superconducting power apparatus, it is necessary to establish the dielectric technology in coolants like LN₂. Among the dielectric technology, surface flashover characteristics are studied with several simplified spacers at the structural aspects. Double pancake coil can apply to transformer and fault current limiter, etc. To design dielectric system of high temperature superconducting transformer consisting of double pancake coils, this study discusses an effective insulator composition. Circular shape insulator divided into two parts should be inserted between coils and the insulator should cover electric stresses concentrated at the circumference of the coils which are in the same section of double pancake coils facing each other.     

Development of a superconducting fault current limiter using various high-speed circuit breakers

The authors constructed and tested a model superconducting fault current limiter (SFCL) using a high-temperature superconducting film according to a design that includes a vacuum interrupter with an electromagnetic repulsion mechanism. The superconductor and the vacuum interrupter are connected in parallel with a bypass coil. If a fault occurs and current flows through the system, the superconductor is quenched and the current is transferred to the parallel coil because of the voltage drop in the superconductor. This large current in the parallel coil actuates the magnetic repulsion mechanism of the vacuum interrupter. On opening the vacuum interrupter, the current in the superconductor is interrupted. This model is expected to exhibit very low-energy consumption by the superconductor. The authors succeeded in interrupting the current flowing in the superconductor within a half-cycle using a prototype SFCL. An improved SFCL with higher voltage and current ranges was used to carry out current-limiting tests and to investigate the possibility of adapting our SFCL in a power system. The authors also carried out a currentlimiting test using a conventional high-speed vacuum circuit breaker (HSVCB) as a new method for realising our concept.     

Proposal of DC shield reactor type superconducting fault current limiter

Saturated DC reactor type superconducting fault current limiter (SFCL) had been proposed two years ago. It was classified to rectifier type SFCL. The changing inductance value with the operating mode has superior characteristics to reduce voltage sag during step increase of the load current. But it has the disadvantage of its weight. In this paper, rectifier type SFCL with shielded reactor has been proposed. The reactor which has superconducting ring or tube inside its winding is substituted to the DC link of the rectifier. The configuration looks like an air core transformer with secondary short winding. When the current through the bulk shield-ring reaches to a certain level, the flux penetrates to the shield body and finite impedance appears in the primary winding. In other words, when the surface flux density exceeds its critical flux density, the flux penetrates into the bulk superconductor, and increases equivalent inductance. The equivalent transient resistance of the shield was represented as a function of exponential of the time. Using this equivalent transient resistance, the transient impedance was expressed. The transient wave analysis using EMTDC (electro-magnetic transients in DC systems) has been described. Simulated waveforms are shown considering the source inductance, the leakage inductance, the coupling coefficient and the forward voltage drop of the semiconductor. And voltage sag was also investigated with 50% step load increase.Preliminary design was also performed. The coil size and number of turns are designed to obtain adequate inductance for the current limitation, and the central magnetic field of the coils are calculated. There is optimal aspect ratio to minimize the magnetic field with restriction in outer diameter of the coil.     

Research on resistance characteristics of YBCO tape under short-time DC large current impact

Research of the resistance characteristics of YBCO tape under short-time DC large current impact is the foundation of the developing DC superconducting fault current limiter (SFCL) for voltage source converter-based high voltage direct current system (VSC-HVDC), which is one of the valid approaches to solve the problems of renewable energy integration. SFCL can limit DC short-circuit and enhance the interrupting capabilities of DC circuit breakers. In this paper, under short-time DC large current impacts, the resistance features of naked tape of YBCO tape are studied to find the resistance – temperature change rule and the maximum impact current. The influence of insulation for the resistance – temperature characteristics of YBCO tape is studied by comparison tests with naked tape and insulating tape in 77 K. The influence of operating temperature on the tape is also studied under subcooled liquid nitrogen condition. For the current impact security of YBCO tape, the critical current degradation and top temperature are analyzed and worked as judgment standards. The testing results is helpful for in developing SFCL in VSC-HVDC.     

Comparison of AC Losses of YBCO Circular Pancake Coils and Infinitely Long Stack Approximation

High-temperature superconducting (HTS) coils are key parts of many large-scale AC applications, such as transformers, superconducting magnetic energy storage, and motors. The estimation of AC losses of pancake coils is necessary for optimizing the design of HTS devices and cryogenic systems. To speed up the computation of AC losses, the numerical model of an infinitely long HTS stack is often utilized. An HTS stack is a good approximation of the circular coil only if the coil radius is sufficiently large, since AC losses will exhibit a stronger asymmetry along the radial direction for small values of coil radii. To assess the validation of an infinitely long stack approximation, the comparisons of AC losses between infinitely long stacks and circular coils with different radii are presented. The turn number varies from 10 to 80. We find that the AC losses of HTS circular coils will gradually increase to the same value as an infinitely long stack with increasing coil radii. A new parameter is proposed to quantitatively describe the correctness of infinitely long stack approximation. Finally, a method of AC loss estimation of HTS pancake coils is proposed.     

VSC-HVDC稳定控制研究

基于电压源换流器（voltage-source converter,VSC）的高压直流输电系统（high voltage direct current,HVDC）拥有良好的有功无功功率控制能力以及更适合构成多端输电系统的优势,目前被认为是极具潜力的输电方式。柔性直流输电系统的控制及稳定性是影响输电系统运行安全和性能的重要因素。针对柔性直流输电系统的研究,首先概述了两端柔性直流输电系统的拓扑及其解耦控制和附加控制方式,然后从基本的两端拓扑结构延伸到多端输电系统拓扑和混合输电系统拓扑,着重分析了多端系统的下垂控制、故障穿越能力和混合直流输电系统的控制,接着又讨论了风电接入之下的柔性直流输电系统的稳定性及控制,可为今后相关研究提供参考。     

Electromagnetic Forces of High-T c Superconducting Coated Conductor Coils Subjected to Sinusoidal Traveling Magnetic Fields

In order to optimize the structure of high temperature superconducting coils for linear motor applications, three separate coils with different shapes made of Re-BCO coated conductor were studied: circular shaped single pancake, circular shaped double-pancake and racetrack shaped single-pancake. The thrust and vertical forces of the three coils above a conventional flat linear three-phases winding were investigated experimentally. With the aid of the experimentally obtained values, it was found that single-pancake coil in the shape of a racetrack was the best selection for a flat single-sided linear motor system. Studies were also made on the frequency characteristics of the vertical force of the racetrack shaped single-pancake coil.     

Comparative Study of Resistive and Inductive Superconducting Fault Current Limiters SFCL for Power System Transient Stability Improvement

This paper presents a comparative study of resistive and inductive superconducting fault current limiter (SFCL) for power systems transient stability improvement. Two applications of transient stability assessment are presented in this paper: The first shows the efficiency of the resistive and inductive SFCL in series with a generator, the second uses SFCL installed in series with a transmission line. SFCL can just be operated during the period from the fault occurrence to the fault clearing; the modeling and the effect of SFCL has been investigated to have higher benefits for the power system. In the present work, modification of the admittance matrix method is used for modeling of SFCL; Critical Clearing Time (CCT) has been used as an index for evaluated transient stability. The transient stability is assessed by the criterion of relative rotor angles, using the Runge–Kutta method. The effectiveness of the proposed method is tested on the WSCC3 nine-bus system applied to the case of three-phase short circuit fault in one transmission line. A simulation and comparison are presented in this document.     

Characteristics of critical current of superconducting solenoid wound with the stacked tape

The high-T_c superconducting (HTS) magnet is an important element for developing HTS power equipments such as the dc reactor of the inductive type superconducting fault current limiter (SFCL). In order to use the HTS magnet for the large-scale power system, its critical current needs to be high enough. Generally, the double pancake HTS magnet has the severe decrease in the critical current because of magnetic field perpendicular to the tape surface. To fabricate a high critical current magnet, we wound a solenoid with the stacked tape. In this paper, the characteristics of the critical current of the HTS solenoid wound with the stacked tape were investigated. The results of this research can be used as the background data for the design of the large-scale HTS magnet.     

Quench Initiation and Propagation in GdBCO Racetrack Pancake Coil for Large-Scale Rotating Machines

Quench tests of a GdBCO racetrack pancake coil were conducted in liquid nitrogen at 77?K. Minimum quench energy and two-dimensional normal zone propagation velocities of the coil are discussed. Longitudinal normal zone propagation velocities in the curved section were almost twice those in the straight portion due to stress effects, showing that protection of the straight portion is of greater importance than protection of the curved portion when using racetrack-type, GdBCO pancake coils in large-scale rotating machines.     

Design and manufacture of a toroidal-type SMES for combination with real-time digital simulator (RTDS)

The authors designed and manufactured a toroidal-type superconducting magnetic energy storage (SMES) system. The toroidal-type SMES was designed using a 3D CAD program. The toroidal-type magnet consists of 30 double pancake coils (DPCs). The single pancake coils (SPCs), which constitute the double pancake coils, are arranged at an angle of 6° from each other, based on the central axis of the toroidal-type magnet. The cooling method used for the toroidal-type SMES is the conduction cooling type. When the cooling method for the toroidal-type SMES was designed, the two-stage Gifford–McMahon (GM) refrigerator was considered. The Bi-2223 HTS wire, which was made by soldering brass on both sides of the superconductor, is used for the magnet winding. Finally, the authors connected the toroidal-type SMES to a real-time digital simulator (RSCAD/RTDS) to simulate voltage sag compensation in a power utility.     

Two-dimensional normal zone propagation in BSCCO-2223 pancake coils

We present the results of an experimental and analytical study of two-dimensional normal zone propagation in pancake test coils, wound with silver-sheathed BSCCO-2223 tapes. Two test coils were studied in detail, one having three and the other eight layers. Each test coil was housed in an adiabatic environment whose temperature (20-70 K) was controlled and maintained by a two-stage G-M cryocooler and placed in a background field (0-6 T) generated by a Bitter magnet. With a test coil carrying a transport current (0-200 A), a local heat disturbance was applied by a heater attached to the outermost layer of the coil. The resulting electrical and thermal responses of the coil were recorded with voltage taps and thermometers attached to the coil. A normal zone propagation code was developed to accurately simulate the voltage and temperature responses of each coil for both quenching and recovering events. The code solves the nonlinear transient heat diffusion equation in two-dimensional cylindrical coordinates with a finite difference method. As an application of this code, a two-coil system, with each coil comprised of one double pancake wound with silver-sheathed BSCCO tape, was studied for its quench behaviour as one of the coils was driven normal locally. The simulation results indicate that the value of a shunt resistor connected across the terminals of each coil has a profound effect on the level of hot-spot temperature reached in the quench initiation spot.     

The electric characteristics of HTS double-pancake coil with AC pulse over currents

A double pancake coil was designed and manufactured with a 36-m long Bi-2223/Ag tape. The tape was insulated by 25 μm thick Kapton tapes, which can stand a voltage of 400 V_rms in liquid nitrogen. The whole double pancake was impregnated with epoxy resin. AC over-current experiments of the coil were performed by applying constant AC voltages to the two terminals of the coil and lasted for 3 s. The experiment began first at a lower voltage of 33.6 V_rms, and then the voltage stepped up till the coil was burned out at the pulse voltage of 202.7 V_rms. All of the experiments were carried out with the coil dipped in liquid nitrogen. The current waveforms were measured. The impedance and resistance characters of the HTS coil with its over pulse currents were analyzed from the experiment results. At the end of this paper, some conclusions derived from the experiment results and their analyses are given, which are helpful for the safety operating of the HTS coils in power applications.     

Experimental and Numerical Study of Co-ordination of Resistive-Type Superconductor Fault Current Limiter and Relay Protection

Superconducting fault current limiter (SFCL) has become one of the most ideal current limiting devices to solve the problem of increasing short-circuit current in high-voltage power grid. This paper presents a resistive-type SFCL model developed using simulation software PSCAD/EMTDC. After being verified by finite-element model and experimental results, the model is used to study the impact of SFCLs on the power grid and the co-ordination between SFCL and relay protections in 10 kV distribution network. A series of simulations are carried out to find appropriate parameters of SFCL model to cooperate with relay protection devices. The final result in this paper could provide important quantitative basis of parameters for SFCL to be applied in a real power system.     

Research on DC Protection Strategy in Multi-Terminal Hybrid HVDC System

Multi-terminal hybrid high-voltage direct current (HVDC) systems have been developed quickly in recent years in power transmission area. However, for voltage-source converter (VSC) stations in hybrid HVDC systems, no direct current (DC) filters are required. In addition, the DC reactor is also not installed at the line end because the DC fault can be limited by the converter itself. This means that the boundary element at the line end is absent, and the single-ended protections used in line commutated converter (LCC) based HVDC (LCC-HVDC) systems or VSC-HVDC systems cannot distinguish the fault line in multi-terminal hybrid HVDC systems. This paper proposes a novel single-ended DC protection strategy suitable for the multi-terminal hybrid HVDC system, which mainly applies the transient information and active injection concept to detect and distinguish the fault line. Compared with the single-ended protections used in LCC-HVDC and VSC-HVDC systems, the proposed protection strategy is not dependent on the line boundary element and is thus suitable for the multi-terminal hybrid HVDC system. The corresponding simulation cases based on power systems computer aided design (PSCAD)/electromagnetic transients including DC (EMTDC) are carried out to verify the superiority of the proposed protection.     

Low resistance splices for HTS devices and applications

This paper discusses the preparation methodology and performance evaluation of low resistance splices made of the second generation (2G) high-temperature superconductor (HTS). These splices are required in a broad spectrum of HTS devices including a large aperture, high-field solenoid built in the laboratory to demonstrate a superconducting magnetic energy storage (SMES) device. Several pancake coils are assembled in the form of a nested solenoid, and each coil requires a hundred meters or more of 2G (RE)BCO tape. However, commercial availability of this superconductor with a very uniform physical properties is currently limited to shorter piece lengths. This necessitates us having splices to inter-connect the tape pieces within a pancake coil, between adjacent pancake coils, and to attach HTS current leads to the magnet assembly. As a part of the optimization and qualification of splicing process, a systematic study was undertaken to analyze the electrical performance of splices in two different configurations suitable for this magnet assembly: lap joint and spiral joint. The electrical performance is quantified in terms of the resistance of splices estimated from the current-voltage characteristics. It has been demonstrated that a careful application of this splicing technique can generate lap joints with resistance less than 1 nΩ at 77 K.