Polymersome formation mechanism and formation rate in stirred‐tank reactors

Uniform polymersomes (polymer vesicles) made of poly(2‐methyloxazoline)₁₅‐b‐poly(dimethylsiloxane)₆₈‐b‐poly(2‐methyloxazoline)₁₅ (PMOXA15–PDMS68–PMOXA15) can be formed in miniaturized‐stirred tank reactors by the aid of a recently published process. In this study, the occurring self‐assembly mechanism was elucidated by using transmission electron microscopy. Subsequent to the initial formation of small spherical micelles and the following fusion to worm‐like micelles, two simultaneously occurring pathways, describing the transformation of further intermediate structures to the desired vesicles, were found. The resulting particle increase was followed by dynamic light scattering. Thus, the vesicle formation rate was judged by the linear increase of the particle diameter over time. While temperature showed no influence, higher initial polymer concentrations and lower final solvent concentrations accelerated the polymersome formation. Besides, the process was crucially dependent on the agitation speed. While spherical micelles did not transform into polymersomes when no stirring or too slow stirring is applied, the self‐assembly process was accelerated by increasing the agitation speed. Uniform polymeric vesicles can be formed under vigorous stirring in stirred‐tank reactors in short process times. In this study, the underlying mechanisms of vesicle formation were elucidated, showing that the polymer forms small micellar structures before undergoing two separate pathways to form the desired vesicular structures. The formation rate of the polymer vesicles was mainly dependent on the agitation speed but also on the polymer and solvent concentrations, highlighting the need for controlled formation conditions. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46077.     

pH‐responsive poly(ethylene glycol)‐poly(ϵ‐caprolactone)‐poly(glutamic acid) polymersome as an efficient doxorubicin carrier for cancer therapy

The synthesis, characterization and potential application in the doxorubicin (Dox) delivery system of a biodegradable polypeptide‐based block copolymer, poly(ethylene glycol)₂₀₀₀‐poly(?‐caprolactone)₆₀₀₀‐poly(glutamic acid)₁₀₀₀ (PEG₂₀₀₀‐PCL₆₀₀₀‐PGA₁₀₀₀), was investigated. The copolymer was synthesized via ring‐opening polymerization and characterized by ¹H NMR and Fourier transform IR. The synthesized copolymer could self‐assemble into aggregates and the critical aggregation concentration was 0.23 mg mL^?1. Transmission electron microscopy indicated that spherical polymersomes formed with a desirable size about 180 nm. Therefore Dox was encapsulated into these polymersomes, and then we investigated its applications in a drug delivery system. These Dox‐loaded polymersomes (PolyDox) were characterized by dynamic light scattering, zeta potential and pH responsiveness measurements. In vitro drug release indicated that the release rate of drug from PolyDox was pH‐responsive and significantly decreased. The drug pharmacokinetic parameters were improved in comparison to the group treated with free Dox, which proved the prolonged Dox release from PolyDox. A WST‐1 assay indicated a low toxicity and good compatibility of copolymer to cells within 48 h. The results also showed that PolyDox appeared to induce a higher anti‐tumor effect. Cell uptake results indicated that PolyDox displayed higher cellular uptake in A549 cells. Endocytosis inhibition results demonstrated that the internalization of PolyDox was mostly mediated by the fluid‐phase endocytosis pathway. © 2017 Society of Chemical Industry     

Biodegradable polymersomes from four‐arm PEG‐b‐PDLLA for encapsulating hemoglobin

A series of four‐arm star block copolymers poly(ethylene glycol)‐block‐poly(d,l ‐lactide) (PEG‐PDLLA) with different hydrophobic length were synthesized by ring‐opening polymerization of lactide and characterized using ¹H NMR and gel permeation chromatography (GPC). These copolymers could self‐assemble in aqueous solution to form the vesicle structure with controlled size and morphologies. Transmission electron microscopy (TEM) and DLS show the polymersomes are spherical with diameter of 70～500 nm. The polymersomes made by direct hydration of copolymer thin films in water exhibit the controllable ability of encapsulating hemoglobin under mild condition. The hemoglobin content in the polymersomes could reach to 35 wt %. More importantly, the encapsulated hemoglobin keeps its own bioactivity and is capable of binding oxygen. This hemoglobin‐encapsulated four‐arm PEG‐PLA polymersomes could have the potential to be applied as an artificial oxygen carrier for transfusion. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40433.     

Sequence analysis and fiber properties of a blend of poly(ethylene terephthalate) and poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)

Blends of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate‐co‐4,4′‐ bibenzoate) (PETBB) are prepared by coextrusion. Analysis by ¹³C‐NMR spectroscopy shows that little transesterification occurs during the blending process. Additional heat treatment of the blend leads to more transesterification and a corresponding increase in the degree of randomness, R. Analysis by differential scanning calorimetry shows that the as‐extruded blend is semicrystalline, unlike PETBB15, a random copolymer with the same composition as the non‐ random blend. Additional heat treatment of the blend leads to a decrease in the melting point, T_m, and an increase in glass transition temperature, T_g. The T_m and T_g of the blend reach minimum and maximum values, respectively, after 15 min at 270°C, at which point the blend has not been fully randomized. The blend has a lower crystallization rate than PET and PETBB55 (a copolymer containing 55 mol % bibenzoate). The PET/PETBB55 (70/30 w/w) blend shows a secondary endothermic peak at 15°C above an isothermal crystallization temperature. The secondary peak was confirmed to be the melting of small and/or imperfect crystals resulting from secondary crystallization. The blend exhibits the crystal structure of PET. Tensile properties of the fibers prepared from the blend are comparable to those of PET fiber, whereas PETBB55 fibers display higher performance. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1793–1803, 2004     

Thermal degradation of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) as studied by TG,TG–FTIR,and Py–GC/MS

The thermal degradation kinetics of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [poly(HB–HV)] under nitrogen was studied by thermogravimetry (TG). The results show that the thermal degradation temperatures (T_o, T_p, and T_f) increased with an increasing heating rate (B). Poly(HB–HV) was thermally more stable than PHB because its thermal degradation temperatures, T_o(0), T_p(0), and T_f(0)—determined by extrapolation to B = 0°C/min—increased by 13°C–15°C over those of PHB. The thermal degradation mechanism of PHB and poly(HB–HV) under nitrogen were investigated with TG–FTIR and Py–GC/MS. The results show that the degradation products of PHB are mainly propene, 2‐butenoic acid, propenyl‐2‐butenoate and butyric‐2‐butenoate; whereas, those of poly(HB–HV) are mainly propene, 2‐butenoic acid, 2‐pentenoic acid, propenyl‐2‐butenoate, propenyl‐2‐pentenoate, butyric‐2‐butenoate, pentanoic‐2‐pentenoate, and CO₂. The degradation is probably initiated from the chain scission of the ester linkage. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1530–1536, 2003     

Thermal degradation kinetics of poly(N‐adamantyl‐exo‐nadimide) synthesized by addition polymerization

The thermal decomposition behavior and degradation kinetics of poly(N‐adamantyl‐exo‐nadimide) were investigated with thermogravimetric analysis under dynamic conditions at five different heating rates: 10, 15, 20, 25, and 30°C/min. The derivative thermogravimetry curves of poly(N‐adamantyl‐exo‐nadimide) showed that its thermal degradation process had one weight‐loss step. The apparent activation energy of poly(N‐adamantyl‐exo‐nadimide) was estimated to be about 214.4 kJ/mol with the Ozawa–Flynn–Wall method. The most likely decomposition process was an F1 deceleration type in terms of the Coats–Redfern and Phadnis–Deshpande results. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3003–3009, 2007     

An improved phase‐inversion process for the preparation of silica/poly[styrene‐co‐(acrylic acid)] core–shell microspheres: synthesis and application in the field of polyolefin catalysis

Spherical and well‐dispersed silica/poly[styrene‐co‐(acrylic acid)] (SiO₂/PSA) core–shell particles have been synthesized using an improved phase‐inversion process. The resulting particles were successfully used as supports for polyolefin catalysts in the production of polyethylene with broad molecular weight distribution. Through the vapor phase, instead of the liquid phase in the traditional process, a non‐solvent was introduced into a mixture of micrometer‐sized SiO₂ and PSA solution. The core–shell structure of the resulting SiO₂/PSA microspheres was confirmed using optical microscopy, scanning electron microscopy, Fourier transfer infrared spectrometry, thermogravimetric analysis and measurement of nitrogen adsorption/desorption isotherms. In order to avoid agglomeration of particles and to obtain a good dispersion of the SiO₂/PSA core–shell microspheres, the non‐solvent was added slowly. As the concentration of PSA solution increased, the surface morphology of the core–shell particles became looser and more irregular. However, the surface area and the pore volume remained the same under varying PSA concentrations. The SiO₂/PSA core‐shell microspheres obtained were used as a catalyst carrier system in which the core supported (n‐BuCp)₂ZrCl₂ and the shell supported TiCl₄. Ethylene/1‐hexene copolymerization results indicated that the zirconocene and titanium‐based Ziegler–Natta catalysts were compatible in the hybrid catalyst, showing high activities. The resulting polyethylene had high molecular weight and broad molecular weight distribution. Copyright © 2010 Society of Chemical Industry     

Kinetics of phase separation of poly(styrene‐co‐methyl methacrylate) and poly(styrene‐co‐acrylonitrile) blends

The phase behavior and kinetics of phase separation for blends of the random copolymer poly(styrene‐co‐methyl methacrylate) (SMMA) and poly(styrene‐co‐acrylonitrile) (SAN) were studied by using small‐angle laser light scattering. The partially miscible SMMA/SAN blends undergo spinodal decomposition (SD) and subsequent domain coarsening when quenched inside the unstable region. For blends of SMMA and SAN, the early stages of the phase separation process could be observed, unlike a number of other blends where the earliest stages are not visible by light scattering. The process was described in terms of the Cahn–Hilliard linear theory. Subsequently, a coarsening process was detected and the time evolution of q_m at the beginning of the late stages of phase separation followed the relationship q_m∝t^?1/3, corresponding to an evaporation–condensation mechanism. Self‐similar growth of the phase‐separated structures at different timescales was observed for the late stage. Copyright © 2004 Society of Chemical Industry     

Synthesis and characterization of novel optically active poly(amide–imide)s containing N,N′‐(pyromellitoyl)‐bis‐L‐valine diacid chloride and 5,5‐disubstituted hydantoin derivatives under microwave irradiation

Pyromellitic dianhydride (1,2,4,5‐benzenetetracarboxylic acid 1,2,4,5‐dianhydide) was reacted with L ‐valine in a mixture of acetic acid and pyridine (3:2) at room temperature, and then was refluxed at 90–100 °C, N,N′‐(pyromellitoyl)‐bis‐L ‐valine diacid was obtained in quantitative yield. The imide–acid was converted to N,N′‐(pyromellitoyl)‐bis‐L ‐valine diacid chloride by reaction with thionyl chloride. Rapid and highly efficient synthesis of a number of poly(amide–imide)s was achieved under microwave irradiation using a domestic microwave oven by polycondensation of N,N′‐(pyromellitoyl)‐bis‐L ‐valine diacid chloride with six different derivatives of 5,5‐disubstituted hydantoin compounds in the presence of a small amount of a polar organic medium that acts as a primary microwave absorber. A suitable organic medium was o‐cresol. The polycondensation proceeded rapidly, compared with conventional melt polycondensation and solution polycondensation and was almost completed within 8 min, giving a series of poly(amide–imide)s with inherent viscosities in the range 0.15–0.36 dl g^?1. The resulting poly(amide–imide)s were obtained in high yield and are optically active and thermally stable. All of the above compounds were fully characterized by Fourier‐transform infrared (FT‐IR) spectroscopy, elemental analysis, inherent viscosity (η_inh) measurements, solubility testing and specific rotation measurements. The thermal properties of the poly(amide–imide)s were investigated by using thermogravimetric analysis. Copyright © 2004 Society of Chemical Industry     

Synthesis of poly[(2‐oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether‐co‐N‐phenylmaleimide] and its miscibility in blends with styrene‐acrylonitrile or poly(vinyl chloride)

The aim of the study was to investigate the synthesis of a copolymer bearing cyclic carbonate and its miscibility with styrene/acrylonitrile copolymer (SAN) or poly(vinyl chloride) (PVC). (2‐Oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether (OVE) as a monomer was synthesized from glycidyl vinyl ether and CO₂ using quaternary ammonium chloride salts as catalysts. The highest reaction rate was observed when tetraoctylammonium chloride (TOAC) was used as a catalyst. Even at the atmospheric pressure of CO₂, the yield of OVE using TOAC was above 80% after 6 h of reaction at 80°C. The copolymer of OVE and N‐phenylmaleimide (NPM) was prepared by radical copolymerization and was characterized by FTIR and ¹H‐NMR spectroscopies and differential scanning calorimetry (DSC). The monomer reactivity ratios were given as r₁ (OVE) = 0.53–0.57 and r₂ (NPM) = 2.23–2.24 in the copolymerization of OVE and NPM. The films of poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were cast from N‐dimethylformamide. An optical clarity test and DSC analysis showed that poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were both miscible over the whole composition range. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1809–1815, 2000     

Synthesis and properties of new aromatic poly(ester‐imide)s derived from 4‐p‐biphenyl‐2,6‐bis(4‐trimellitimidophenyl) pyridine and various dihydroxy compounds

A novel class of wholly aromatic poly(ester‐imide)s, having a biphenylene pendant group, with inherent viscosities of 0.32–0.49 dL g^?1 was prepared by the diphenylchlorophosphate‐activated direct polyesterification of the preformed imide‐ring‐containing diacid, 4‐p‐biphenyl‐2,6‐bis(4‐trimellitimidophenyl)pyridine (1) with various aromatic dihydroxy compounds in the presence of pyridine and lithium chloride. A reference diacid, 2,6‐bis(trimellitimido)pyridine (2) without a biphenylene pendant group and two phenylene rings in the backbone, was also synthesized for comparison purposes. At first, with due attention to structural similarity and to compare the characterization data, a model compound (3) was synthesized by the reaction of compound 1 with two mole equivalents of phenol. Moreover, the optimum condition of polymerization reactions was obtained via a study of the model compound synthesis. All of the resulting polymers were characterized by Fourier transform infrared and ¹H NMR spectroscopy and elemental analysis. The ultraviolet λ_max values of the poly(ester‐imide)s were also determined. All of the resulting polymers exhibited excellent solubility in common organic solvents, such as pyridine, chloroform, tetrahydrofuran, and m‐cresol, as well as in polar organic solvents, such as N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide, and dimethyl sulfoxide. The crystalline nature of the polymers obtained was evaluated by means of wide‐angle X‐ray diffraction. The resulting poly(ester‐imide)s showed nearly an amorphous nature, except poly(ester‐imide) derived from 4,4′‐dihydroxy biphenyl. The glass transition temperatures (T_g) of the polymers determined by differential scanning calorimetry thermograms were in the range 298–342 °C. The 10% weight loss temperatures (T_10%) from thermogravimetric analysis curves were found to be in the range 433–471 °C in nitrogen. Films of the polymers were also prepared by casting the solutions. Copyright © 2006 Society of Chemical Industry     

Synthesis,properties, and self‐assembly of poly(benzyl ether)‐b‐polystyrene dendritic–linear polymers

Poly(benzyl ether)‐b‐polystyrene dendritic–linear polymers were successfully synthesized using a dendritic chloric poly(benzyl ether) (G₁‐Cl, G₂‐Cl, and G₃‐Cl) as the macroinitiator through the atom transfer radical polymerization process. The structure and properties of the resultant polymers were characterizated by gel permeation chromatography, ¹H‐NMR, Fourier transform IR, thermogravimetric analysis, and differential scanning calorimetry. It was found that the temperature, reaction time, molar ratio of the macroinitiator to styrene, and the generation number of the macroinitiator have significant effects on the molecular weights, conversion, and polydispersities of the resulting polymers. These dendritic–linear block polymers had very good solubility in common organic solvents at room temperature. The terminal group (dendritic segments) of the polymers can affect their thermal stability. These dendritic–linear polymers after self‐assembling in selective solvents (chloroform/acetone) formed core–shell micelles. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1106–1112, 2005     

Synthesis and characterization of biodegradable poly(ester‐urethanes) based on bacterial poly(R‐3‐hydroxybutyrate)

A series of poly(R‐3‐hydroxybutyrate)/poly(ε‐caprolactone)/1,6‐hexamethylene diisocyanate‐segmented poly(ester‐urethanes), having different compositions and different block lengths, were synthesized by one‐step solution polymerization. The molecular weight of poly(R‐3‐hydroxybutyrate)‐diol, PHB‐diol, hard segments was in the range of 2100–4400 and poly(ε‐caprolactone)‐diol, PCL‐diol, soft segments in the range of 1080–5800. The materials obtained were investigated by using differential scanning calorimetry, wide angle X‐ray diffraction and mechanical measurements. All poly(ester‐urethanes) investigated were semicrystalline with T_m varying within 126–148°C. DSC results showed that T_g are shifted to higher temperature with increasing content of PHB hard segments and decreasing molecular weight of PCL soft segments. This indicates partial compatibility of the two phases. In poly(ester‐urethanes) made from PCL soft segments of molecular weight (M_n ≥ 2200), a PCL crystalline phase, in addition to the PHB crystalline phase, was observed. As for the mechanical tensile properties of poly(ester‐urethane) cast films, it was found that the ultimate strength and the elongation at the breakpoint decrease with increasing PHB hard segment content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 703–718, 2002     

Synthesis,characterization, and thermal degradation of novel poly(2‐(5‐bromo benzofuran‐2‐yl)‐2‐oxoethyl methacrylate)

A novel methacrylate monomer containing benzofuran side group, 2‐(5‐bromo benzofuran‐2‐yl)‐2‐oxoethyl methacrylate (BOEMA), was synthesized from esterification reaction of 2‐bromo‐1‐(5‐bromo benzofuran‐2‐yl) ethanone with sodium methacrylate at 85°C in the presence of 1,4‐dioxane solvent. After characterization with Fourier transform infrared spectrophotometer, nuclear magnetic resonance (¹H‐NMR and ¹³C‐NMR), its homopolymerization was carried out by free radical polymerization at 60°C in the presence of benzoyl peroxide initiator and 1,4‐dioxane solvent. The glass transition temperature (T_g) of the synthesized novel polymer, poly(2‐(5‐bromo benzofuran‐2‐yl)‐2‐oxoethyl methacrylate) [poly(BOEMA)], was determined to be 137°C with differential scanning calorimetry technique. Thermal degradation kinetics of poly(BOEMA) was investigated by thermogravimetric analysis method at different heating rates with 5°C/min intervals between measurements. From dynamic measurements, the analysis of each process mechanism of Coats–Redfern and Van Krevelen methods showed that the most probable model for the decomposition process of poly(BOEMA) homopolymer agrees with the random nucleation, F₁ mechanism. The apparent decomposition activation energies of poly(BOEMA) by Kissinger's and Flynn–Wall–Ozawa methods in the studied conversion range were 188.47 and 180.13 kJ/mol, respectively. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Characteristics of poly(AAc5‐co‐HPMA3‐cl‐EGDMA15) hydrogel‐immobilized lipase of Pseudomonas aeruginosa MTCC‐4713

Four series of noble networks were synthesized with acrylic acid (AAc) copolymerized with varying amount of 2‐hydroxy propyl methacrylate or dodecyl methacrylate (AAc/HPMA or AAc/DMA; 5:1 to 5:5, w/w) in the presence of ethylene glycol dimethacrylate (EGDMA; 1, 5, 10, 15, and 20%, w/w) as a crosslinker and ammonium per sulfate (APS) as an initiator. Each of the networks was used to immobilize a purified lipase from Pseudomonas aeruginosa MTCC‐4713. The lipase was purified by successive salting out with (NH₄)₂SO₄, dialysis, and DEAE anion exchange chromatography. Two of the matrices, E_15a, i.e. [poly (AAc₅‐co‐DMA₁‐cl‐EGDMA₁₅)] and I_15c, i.e. [poly (AAc₅‐co‐HPMA₃‐cl‐EGDMA₁₅)], that showed relatively higher binding efficiency for lipase were selected for further studies. I_15c‐hydrogel retained 58.3% of its initial activity after 10th cycle of repetitive hydrolysis of p‐NPP, and I_15c was thus catalytically more stable and efficient than the other matrix. The I_15c‐hydrogel‐immobilized enzyme showed maximum activity at 65°C and pH 9.5. The hydrolytic activity of free and I_15c‐hydrogel‐immobilized enzyme increased profoundly in the presence of 5 mM chloride salts of Hg²⁺, NH₄⁺, Al³⁺, K⁺, and Fe³⁺. The immobilized lipase was preferentially active on medium chain length p‐nitrophenyl acyl ester (C:8, p‐nitrophenyl caprylate). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4636–4644, 2006     

Synthesis of star‐shaped poly(ϵ‐caprolactone) by samarium‐based tetrafunctional initiator and its dilute‐solution properties

An in situ–generated tetrafunctional samarium enolate from the reduction of 1,1,1,1‐tetra(2‐bromoisobutyryloxymethyl)methane with divalent samarium complexes [Sm(PPh₂)₂ and SmI₂] in tetrahydrofuran has proven to initiate the ring‐opening polymerization of ?‐caprolactone (CL) giving star‐shaped aliphatic polyesters. The polymerization proceeded with quantitative conversions at room temperature in 2 h and exhibited good controllability of the molecular weight of polymer. The resulting four‐armed poly(?‐caprolactone) (PCL) was fractionated, and the dilute‐solution properties of the fractions were studied in tetrahydrofuran and toluene at 30°C. The Mark–Houwink relations for these solvents were [η] = 2.73 × 10^?2M_w^0.74 and [η] = 1.97 × 10^?2M_w^0.75, respectively. In addition, the unperturbed dimensions of the star‐shaped PCL systems were also evaluated, and a significant solvent effect was observed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 175–182, 2006     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Synthesis and characterization of new aromatic poly(amide–imide)s based on 4‐aryl‐2,6‐bis(4‐trimellitimidophenyl) pyridines

New diimide–dicarboxylic acids, ie 4‐phenyl‐2,6‐bis(4‐trimellitimidophenyl)pyridine and 4‐p‐biphenyl‐2,6‐bis‐(4‐trimellitimidophenyl)pyridine, were synthesized by the condensation reaction of 4‐phenyl‐2,6‐bis(4‐aminophenyl)pyridine and 4‐p‐biphenyl‐2,6‐bis(4‐aminophenyl)pyridine with trimellitic anhydride in glacial acetic acid or dimethylformamide. The monomers were fully characterized by FT‐IR and NMR spectroscopies, and elemental analyses. A series of novel poly(amide–imide)s with inherent viscosities of 0.68–0.87 dl g^?1 was prepared from the two diimide–diacids with various aromatic diamines by direct polycondensation. The poly(amide–imide)s were characterized by FT‐IR and NMR spectroscopies. The λ_max data for the resulting poly(amide–imide)s were in the range of 260–292 nm. These polymers exhibited good solubilities in polar aprotic solvents. The 10 % weight loss temperatures are above 485 °C under a nitrogen atmosphere. Copyright © 2004 Society of Chemical Industry     

Syntheses of cyclic poly(lactones) by zwitterionic ring opening polymerization catalyzed by N‐heterocyclic carbene

Synthesis of cyclic biopolymers from renewable monomers remains a big challenge because of lack of efficient catalysts. The organocatalyst of N‐heterocyclic carbene (NHC), (+)‐1‐methyl‐3‐menthoxymethyl imidazol‐2‐ylidene, is used to prepare cyclic polylactones including poly(ε‐caprolactone) (poly(ε‐CL)), poly(δ‐valearolactone) (poly(δ‐VL)), and poly(ε‐caprolactone‐co‐δ‐valearolactone) (poly(ε‐CL‐co‐δ‐VL)) via zwitterionic ring opening polymerization. The NHC catalyst is founded a highly efficient organic catalyst for the polymerization. The resulting cyclic polymers show a melting temperature (T_m) in a range of 20–60°C, which is dramatically lower than the T_m of cyclic poly(lactide) (T_m = 120–150°C). The resulting copolymer, cyclic poly(ε‐CL‐co‐δ‐VL) owns high molecular weight comparing with corresponding linear poly(ε‐CL‐co‐δ‐VL) produced by other catalysts. The synthesized cyclic homo and copolymers were characterized by ¹H‐, ¹³C‐NMR spectroscopy, gel permeation chromatography, differential scanning calorimetry–thermogravimetric analysis and matrix‐assisted laser desorption ionization‐time of flight mass spectrometry. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013