γ ? α2 Phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%)

The ₂ phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%) alloy has been studied by analytical electron microscopy. ₂ and phases were found at grain boundaries. ₂ layers that suspended in layers and interfacial ledge higher than 2d ₍₁₁₁₎ at /₂ interfaces were observed in the lamellar grains. These facts indicated that ₂ phase transformation and dynamic recrystallization have occurred during high temperature stress rupture deformation. It can be concluded that deformation induced ₂ phase transformation and dynamic recrystallization resulted in the presence of particles at grain boundaries. A structural and compositional transition area between deformation-induced ₂(or ) and its adjacently original (or ₂) phases was found by HREM and EDS and is suggested as a way to transform between and ₂ phase during high temperature stress rupture deformation. The transition area was formed by slide of partial dislocations on close-packed planes and diffusion of atoms.     

Preferentially orientated precipitation in MnTiO3 single crystals

Preferentially orientated precipitation of -TiO₂ (rutile) needles in single crystals of MnTiO₃ grown by a floating-zone method under a controlled atmosphere of oxygen fugacity was studied. Optical microscopy and X-ray analysis revealed that the orientation relation between the -TiO₂ precipitates and the MnTiO₂ matrix is: {000 1}MnTiO₃// {111}-TiO₂ and 11¯20MnTiO₃// 110-TiO₂. The precipitation phenomenon was explained by introducing a nucleation and growth mechanism which was experimentally supported by heat treating experiments.     

Ultrasonic attenuation of longitudinal and shear waves in superconducting lead

Longitudinal and shear wave ultrasonic attenuations have been measured in high-purity Pb on two single crystals obtained from the same ingot. The measurements were done at low temperatures, at different frequencies, and in transverse magnetic fields, up to a field of 7.3 kG. The propagation directions in the two crystals were along [100] and [110]. For some propagation and polarization directions the _s / _n ratio is found to be frequency-independent, while for others, large divergences in the _s / _n ratios at different frequencies are observed. A sharp decrease of _s / _n nearT _c is observed for a particular longitudinal wave propagation, but not in any shear wave propagation. In some cases _s / _n is found to be abnormally high and this feature is associated with a peak in attenuation _n and a relatively high _n at 7.2 K. None of the _s / _n curves fits closely to any BCS energy gap. For longitudinal waves the high magnetic field (H) dependence of the normal state attenuation was found to agree qualitatively with the free electron theory for propagation along [100], but not for propagation along [110]. For shear waves the high-field attenuations do not extrapolate to zero asH tends to infinity. For all propagation and polarization directions the high-field attenuations show 1/H ² field dependence.     

Specific heat near the lambda point in 4He and 3He-4He mixtures: Test of universality of the critical exponent and the amplitude ratio,and observation of the critical-tricritical crossover effect

The specific heat under saturated vapor pressure of pure ⁴He and of six ³He-⁴He mixtures up to X = 0.545 was measured in the temperature range 3 × 10^–6 <¦T-T ¦ <10^–2 K. The critical exponents and along the path = are independent of X up to X = 0.545, where (= ₃ – ₄) is the difference between chemical potentials. If we take account of higher order terms, the exponent (= ) and the amplitude ratio A /A are independent of X up to X = 0.545. The values of and A /A are –0.023 and 1.090, respectively. The critical-tricritical crossover effect was observed for X = 0.545 and the boundary of crossover region closest to the critical region was at /T = (1–2) × 10^–4, where is the distance ¦T – T ¦ along the path = . This value is in good agreement with the estimated value by Riedel et al. But, remarkably, in the case of X = 0.439 this effect was not observed.     

Heat transfer in plane film formation

A mathematical model is obtained for the process of cooling with formation of a planar film. The solution obtained is verified experimentally.Notation mean axial velocity gradient - v_x current axial velocity - v_o initial polymer velocity - v₁ sampling velocity - K draw ratio - deformation rate tensor - x, y, z spatial coordinates - X, Y dimensionless coordinates - L() differential operator - T temperature - T_o initial temperature - T_c temperature of surrounding medium - dimensionless temperature - dimensionless temperature averaged over film thickness - thermal-diffusivity coefficient - 2_o initial film thickness - thermal conductivity - heat-transfer coefficient - f(X) distance function - Bi Biot criterion, Bi_o, Biot criterion calculated for initial film thickness - Gz* modified Graetz criterion - V dimensionless velocity - ₁, ₂, ₃ heat-transfer coefficients produced by radiation, free convection, and forced convection - v_c, _c mean velocity and film half-thickness in formation zone - T₁ calculated temperature value - T₂ experimental temperature value - l formation zone length Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 37, No. 5, pp. 854–858, November, 1979.     

Investigations of the copper isotope effect in oxygen-deficient YBa2Cu3O7−δ

We present data on the copper isotope effect (⁶³Cu-⁶⁵Cu), C_u =-nT_c/nm_Cu, for two isotopic pairs of oxygen-deficient YBa₂Cu₃O_7–, where varies between 0.06 and 0.52. _Cu is below 0.01 at =0.06 (fully oxygenated), it takes values between –0.14 and –0.34 in the 60 K plateau. Larger negative values of _Cu are observed away from the plateau. The dependence of _Cu is similar to that of the pressure effect dnT_c/dP.     

Application of a new iterative method for elastic-plastic stress analysis

A new iterative method for elastic-plastic stress analysis based on a new approximation of the constitutive equations is proposed and compared with standard methods on the accuracy and the computational time in a test problem. The proposed method appears to be better than the conventional methods on the accuracy and comparable with others on the computational time. Also the present method is applied to a crack problem and the results are compared with experimental ones. The agreement of both results are satisfactory.List of symbols u = (u ₁, u ₂) displacements u ^(H) = u ⁽ⁿ⁺¹⁾ - u ⁽ⁿ⁾ u _k ⁽ⁿ⁾ = u _(k ^{(n + 1)} - u ⁽ⁿ⁾ (n, k = 0, 1, 2, ...) - = ₁₁, ₂₂, ₁₂) stresses - = (₁₁, ₂₂, ₁₂) strains - = (₁₁, ₂₂, ₁₂) center of yield surface - D elastic coeffficient matrix, C = D ^–1 - von Mises yield function. The initial yielding is given by f() = _Y - f {f/} - ^* transposed f - H hardening parameter (assumed to be a positive constant for kinematic hardening problems) - time derivative of - [K] total elastic stiffness matrix - T traction vector - = [B] relation between nodal displacements and strains     

Anisotropic grain growth of R-α-sialon (R = Nd and Er)

Two R--sialon (R_0.6Si_9.3Al_2.7O_0.9N_15.1, R=Nd and Er) compositions were first fired at 1750°C/25 min and 1650°C/2 h respectively for completion of the phase transformation. Elongated -sialon grain morphology was developed in both samples after being re-fired at 1800°C for different periods of time. The growth in width of R--sialon grains is controlled by diffusion in the liquid, while the length growth tends to be interfacial reaction controlled. The anisotropic growth of R--sialon is attributed to the large difference in the growth rate constant between the length and the width directions of the grain.     

Microhardness and microbrittleness of several crystalline glass ceramic phases

The micromechanical properties of crystals of -cordierite, spinel, rutile, mullite, -cristobalite, and magnesium aluminosilicate have been studied. It was shown that the maximum Vickers hardness and maximum Dertev microbrittleness are found for crystals of magnesium aluminosilicate, cordierite, and spinel. The minimum values of these parameters are found for crystals of -cristobalite.Translated from Problemy Prochnosti, No. 10, pp. 29–31, October, 1992.     

Phase transitions and high-temperature crystal chemistry of polymorphous modifications of Cs<Subscript>2</Subscript>(UO<Subscript>2</Subscript>)<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)

Phase transitions and thermal deformations of - and -Cs₂(UO₂)₂(MoO₄)₃ were studied by high-temperature X-ray diffraction analysis. In heating of -Cs₂(UO₂)₂(MoO₄)₃ to 625 ± 25°C, the reconstructive phase transition proceeds. -Cs₂(UO₂)₂(MoO₄)₃ is stable up to 700 ±25°C. The thermal expansion of both phases is sharply anisotropic: ₁₁ = 10 × 10^–6, ₂₂ = 33 × 10^–6, ₃₃ = 10 × 10^–6, _V = 53 × 10^–6 deg^–1 for -Cs(UO₂)₂(MoO₄)₃ and ₁₁ = 13 × 10^–6, ₃₃ = 3 × 10^–6, _V = 31 × 10^–6 deg^–1 for -Cs₂ (UO₂)₂ (MoO₄)₃. The anisotropy of thermal expansion is explained by features of the crystal structure of the compounds.Translated from Radiokhimiya, Vol. 46, No. 5, 2004, pp. 405–407.Original Russian Text Copyright © 2004 by Nazarchuk, Krivovichev, Filatov.     

Microstructure-property studies in friction-stir welded, Thixomolded magnesium alloy AM60

Thixomolded magnesium alloy AM60 plates joined by friction-stir welding were observed to be as strong or stronger than the unwelded base material. The thixotropic microstructures of the as-molded plates consisted of either 3% or 18% primary solid fraction of -Mg globules (45 m average size) in a eutectic mixture consisting of -Mg grains (10 m) surrounded by Mg₁₇Al₁₂ intermetallic grains in the -Mg grain boundaries (having an average size of 1–2 m). This complex, composite microstructure became a homogeneous (Mg + 6% Al)), recrystallized, equiaxed grain (10–15 m) microstructure in the weld zone.     

Similarity solutions in axisymmetric mixed-convection boundary-layer flow

The similarity equations for mixed-convection axisymmetric boundary-layer flow are considered. The equations involve a buoyancy parameter and a curvature parameter . The equations are solved numerically and it is found that for large , and of O(1), an asymptotic solution is approached, the nature of which is discussed. When is also large, of O(^1/4), the problem, at leading order, becomes independent of the mainstream and the free-convection limit is obtained. This problem is also discussed, including the behaviour for large values of ₀, the free-convection curvature parameter. For < 0 we find that the solution can be continued past the point where the wall heat transfer becomes zero (where previous mixed-convection similarity solutions in plane geometry were terminated) with the solution ending as 0^–. The nature of this limit is also discussed. For < 0 it is also found that there are solutions only in _b = < 0 with two branches of solution bifurcating out of = _b , and values of _b are computed for a range of . The behaviour of the solution for large values of the curvature parameter , and of O(1), is discussed where it is shown that the solution proceeds in inverse powers of log .     

Flow visualization glass-ceramic: Preliminary experimental and modelling results

A glass-ceramic material was developed to act as a flow visualization material. Preliminary experiments indicate that aperiodic, thermally induced, convective flows can be sustained at normal processing conditions. These flows and the stress and temperature gradients induced are most likely responsible for the anomalous behaviour seen in these materials and the difficulties encountered in their development and in their production on industrial and experimental scales. A simple model describing the dynamics of variable-viscosity fluids was developed and was shown to be in qualitative agreement with more sophisticated models as well as with experimental results. The model was shown to simulate the dependence of the critical Rayleigh number for the onset of convection on the viscous properties of the fluid at low T, and also to simulate quenching behaviour when the temperature differences were high.Nomenclature C _p Heat capacity - D, E, F Expansion coefficients - H Height of the roll cell - Pr Prandtl number - R _a Rayleigh number - R _c Critical Rayleigh number for the onset of convection in a constant-viscosity fluid - S Dimensionless stream function - T Temperature - T _m Mean temperature - T ₀ Bottom surface temperature - T _r Reference temperature - a Aspect ratio of cell - g Acceleration due to gravity - k Thermal conductivity - k ₁ Function related to ²v/T ² - k ₂ Function related to ⁴v/T ⁴ - r Rayleigh number ratioR _a/R _c - t Time - w Dimensionless vertical coordinate - w _m Mean cell height - x Horizontal coordinate - y Dimensionless horizontal coordinate - z Vertical coordinate - , Constants - _t Thermal expansion coefficient - Constant in viscosity function - T Temperature difference between top and bottom surfaces - _i Viscosity coefficients - Kinematic viscosity - _m Mean kinematic viscosity - Dimensionless kinematic viscosity - Thermal diffusivity - Non-linear temperature function - Dimensionless non-linear temperature function - _o - Stream function - Dimensionless time - Eigenvalues     

Varistor characteristics in PTCR-type (Ba,Sr)TiO3 ceramics prepared by single-step firing in air

This paper deals with donor, acceptor-codoped (Ba_0.4Sr_.6)TiO₃ ceramics with distinct varistor characteristics at room temperature, which were prepared by single-step firing in air. The materials, with the Curie point at around –90 °C, exhibited a large PTCR (positive temperature coefficient of resistivity) effect of more than seven orders of magnitude in the temperature range –90 °C (the resistivity 10³ · cm) to room temperature ( > 10¹⁰ · cm). An apparent dielectric constant of >20000 and tan < 0.05 (at 100 kHz) were observed for the present materials at room temperature, and moreover, the materials exhibited nonlinear current-voltage characteristics with the nonlinear coefficient, , in the range 7–12 and the varistor field, E_v, in the range 0.3–1.0 kV/cm. The value of in the present materials increased systematically with increasing in their PTCR temperature range. It has been found that there exists a close correlation between and the grain-boundary potential barrier height, e, obtained from the -T characteristic of the materials. An almost linear relationship was also found to exist between and log E_v for the present materials.     

The athermal α → ω transformation in Zr-2 at% Nb alloy

The athermal transformation in Zr-2 at.% Nb alloy has been investigated by transmission electron microscopy. Analysis of the selected-area diffraction pattern has shown that the orientation relationships between the omega and the parent-phase in quenched Zr-2 at.% Nb alloy are the same as have been previously observed for the reaction in pure zirconium. Thus it was deduced that the direct transition has taken place in the alloy during cooling. The-originated -particles were visualized using the dark-field technique. The formation of the athermal omega in the-region of-stabilized Zr-Nb alloy is discussed in terms of the relative positions of the free energy equilibrium curvesT ₀ ,T ₀ ,T ₀ and the correspondingM _s ,M _s andT _s start curves. It is concluded that the omega phase can occur over a much wider range of alloy compositions than is usually recognized on the basis of transformation data.     

High temperature oxidation behavior of Ti-Al-Nb ternary alloys

The oxidation behavior of four Ti-Al-Nb ternary alloys with different microstructures were investigated at 1000°C using interrupted oxidation test in air. Alloys with single-phase -TiAl, two-phase -TiAl + ₂-Ti₃Al, multi-phase -TiAl + ₂-Ti₃Al + Nb₂Al and two-phase ₂-Ti₃Al + Nb₂Al were prepared. The oxidation resistance of the Ti-Al-Nb ternary alloy at high temperature was found to be better than that of the binary Ti-Al alloy. Among the four Ti-Al-Nb ternary alloys, the + ₂ two-phase alloy has the best oxidation resistance. The presence of Nb-enriched phase such as Nb₂Al and Nb₃Al decrease the oxidation resistance at elevated temperature presumably due to the formation of Nb₂O₅, which would accelerate the exfoliation of oxide.     

Thermal diffusivity of inhomogeneous systems

The possibility of analyzing the nonsteady temperature fields of inhomogeneous systems using the quasi-homogeneous-body model is investigated.Notation t, t_I, t_i temperature of quasi-homogeneous body inhomogeneous system, and i-th component of system - a, , c thermal diffusivity and conductivity and volume specific heat of quasi-homogeneous body - a_{i i}, c_i same quantities for the i-th component - q heat flux - S, V system surface and volume - x, y coordinates - macrodimension of system - dimensionless temperature Fo=a/² - Bi=/ Fourier and Biot numbers - N number of plates - =h/ ratio of micro- and macrodimensions - _V, volumeaveraged and mean-square error of dimensionless-temperature determination - time - m_i i-th component concentration Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 39, No. 1, pp. 126–133, July, 1980.     

EPR study of polycrystalline superconductors with YBa2Cu3O7 structure

Electron paramagnetic resonance (EPR) of Gd³⁺, Eu²⁺, and copper ions has been investigated in the high-T_c superconductor with YBa₂Cu₃O_7– structure. It has been established that the system is heterogeneous at 0.150.5 and consists of metallic and dielectric regions. The former arises due to oxygen enrichment while the later due to oxygen deficiency. The integral of exchange interaction between Gd³⁺ localized moments and conduction electrons J_sf=0.016 eV has been determined from the normal state temperature dependence of Gd³⁺ EPR linewidth for metallic regions. T_c depression by gadolinium-localized moments for GdBa₂Cu₃O_7– was estimated to be T_c–2K. Anomalies in linewidth temperature dependence upon transition from the normal to the superconducting state have given information about the value and temperature behavior of the superconductor's energy gap. The model, which gives the opportunity to understand some peculiarities of the EPR signal for YBa₂Cu₃O_7– samples, is proposed in terms of several bottlenecked spinsubsystems: spin-liquid in CuO planes and Cu²⁺-O^– and Cu²⁺-O^2– fragments in CuO chains.     

Analysis of heat transfer in the furnace of the P-67 boiler P-67 furnace and improvement of its design

The results of experimental study of heat transfer in the furnace of the P-67 boiler (under the Russian trademark) burning Kansk-Achinsk coal are presented. Means of improving the design of the furnace device are proposed.Notation N energy unit power, MW - _fur furnace air excess coefficient - r gas recirculation degree - q_in incident radiation flux density, kW/m² - a spacing between the combustion chamber walls, m - b_b burner width, m - n number of the burner row, starting from below - and inclination angles of the burners located in front of and behind the combustion chamber axis - d diameter of the conventional circumference, tangential to which the burners are directed, m - q_ch heat-stress of the radiant heat absorbing surface of the active combustion zone, MW/m² - furnace-mean thermal efficiency of deflecting walls Krasnoyarsk Institute of Non-Ferrous Metals, Siberian Branch of the All-Union Heat Engineering Institute, Krasnoyarsk. Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 64, No. 3, pp. 275–278, March, 1993.