Calculation of the conditions to get less than 2 g tar/mn3 in a fluidized bed biomass gasifier

The experimental conditions under which a fluidized bed biomass gasifier can generate a gas with a tar content below 2 g/m_n³ are analyzed by using and developing the model recently published for those gasifiers by Corella and Sanz [Fuel Process. Techn. 2005, 86, 1021–1053]. The analyzed experimental conditions were: the equivalence ratio, the partitioning of the air, between the primary and secondary flows, the location (height) of the inlet of the secondary air flow, the biomass moisture and the biomass flow rate. Results from the modelling work are presented for a given CFB biomass gasifier of commercial size. Some of these results are also being checked in a CFB biomass gasifier at small pilot plant scale. To obtain a gasification gas with a very low tar content the two most important experimental conditions are a high value for the equivalence ratio and a good in-gasifier material which determines the values of the kinetic constants of the reactions involved in the network at the gasifier.     

Comparison of dual fluidized bed steam gasification of biomass with and without selective transport of CO2

A comparison of dual fluidized bed gasification of biomass with and without selective transport of CO₂ from the gasification to the combustion reactor is presented. The dual fluidized bed technology provides the necessary heat for steam gasification by circulating hot bed material that is heated in a separate fluidized bed reactor by combustion of residual biomass char. The hydrogen content in producer gas of gasifiers based on this concept is about 40 vol% (dry basis). Addition of carbonates to the bed material and adequate adjustment of operation temperatures in the reactors allow selective transport of CO₂ (absorption enhanced reforming—AER concept). Thus, hydrogen contents of up to 75 vol% (dry basis) can be achieved. Experimental data from a 120 kW_{Fuel input} pilot plant as well as thermodynamic data are used to determine the mass- and energy-balances. Carbon, hydrogen, oxygen, and energy balances for both concepts are presented and discussed.     

双流化床生物质气化炉研究进展

生物质是重要的清洁可再生能源,双流化床生物质气化技术是将低品位的生物质能转化成高品位氢能的重要途径。本文阐明了双流化床气化过程的基本原理,从燃气中氢气浓度、焦油含量和装置热效率等角度,介绍了双流化床生物质气化技术的早期探索和发展现状,对目前几种典型双流化床生物质气化炉的炉型设计及相关试验研究进行了分析和总结。指出内循环双流化床气化炉结构虽然简单紧凑,但是难以避免气化室和燃烧室之间的气体串混问题;而外循环流化床通过外置返料器很好地解决了气体串混问题。分析了不同气化室优化设计方案对提升燃气品质的理论依据及其优缺点。最后对双流化床生物质气化技术的发展进行了总结和展望,指出双流化床生物质气化制氢具有非常广阔的工业化应用和发展前景。     

Multiphase CFD-based models for chemical looping combustion process: Fuel reactor modeling

Chemical looping combustion (CLC) is a flameless two-step fuel combustion that produces a pure CO₂ stream, ready for compression and sequestration. The process is composed of two interconnected fluidized bed reactors. The air reactor which is a conventional circulating fluidized bed and the fuel reactor which is a bubbling fluidized bed. The basic principle is to avoid the direct contact of air and fuel during the combustion by introducing a highly-reactive metal particle, referred to as oxygen carrier, to transport oxygen from the air to the fuel. In the process, the products from combustion are kept separated from the rest of the flue gases namely nitrogen and excess oxygen. This process eliminates the energy intensive step to separate the CO₂ from nitrogen-rich flue gas that reduce the thermal efficiency.Fundamental knowledge of multiphase reactive fluid dynamic behavior of the gas-solid flow is essential for the optimization and operation of a chemical looping combustor.Our recent thorough literature review shows that multiphase CFD-based models have not been adapted to chemical looping combustion processes in the open literature. In this study, we have developed the reaction kinetics model of the fuel reactor and implemented the kinetic model into a multiphase hydrodynamic model, MFIX, developed earlier at the National Energy Technology Laboratory. Simulated fuel reactor flows revealed high weight fraction of unburned methane fuel in the flue gas along with CO₂ and H₂O. This behavior implies high fuel loss at the exit of the reactor and indicates the necessity to increase the residence time, say by decreasing the fuel flow rate, or to recirculate the unburned methane after condensing and removing CO₂.     

Multiphase CFD Modeling for a Chemical Looping Combustion Process (Fuel Reactor)

There are growing concerns about increasing emissions of greenhouse gases and a looming global warming crisis. CO₂ is a greenhouse gas that affects the climate of the earth. Fossil fuel consumption is the major source of anthropogenic CO₂ emissions. Chemical looping combustion (CLC) has been suggested as an energy‐efficient method for the capture of carbon dioxide from combustion. A chemical‐looping combustion system consists of a fuel reactor and an air reactor. The air reactor consists of a conventional circulating fluidized bed and the fuel reactor is a bubbling fluidized bed. The basic principle involves avoiding direct contact of air and fuel during the combustion. The oxygen is transferred by the oxygen carrier from the air to the fuel. The water in combustion products can be easily removed by condensation and pure carbon dioxide is obtained without any loss of energy for separation. With the improvement of numerical methods and more advanced hardware technology, the time required to run CFD (computational fluid dynamic) codes is decreasing. Hence, multiphase CFD‐based models for dealing with complex gas‐solid hydrodynamics and chemical reactions are becoming more accessible. To date, there are no reports in the literature concerning mathematical modeling of chemical‐looping combustion using FLUENT. In this work, the reaction kinetics models of the (CaSO₄ + H₂) fuel reactor is developed by means of the commercial code FLUENT. The effects of particle diameter, gas flow rate and bed temperature on chemical looping combustion performance are also studied. The results show that the high bed temperature, low gas flow rate and small particle size could enhance the CLC performance.     

Effect of CO<Subscript>2</Subscript> addition on lignite gasification in a CFB reactor: A pilot-scale study

The addition of carbon dioxide to the gasification media during lignite gasification is introduced. The paper presents thermodynamic grounds of CO₂ enhanced gasification using a simplified equilibrium model. Experimental tests conducted using a pilot-scale circulating fluidized bed gasifier are discussed. Detailed analysis of the CO₂/C ratio on process conditions, namely on the process gas composition, lower heating value and H₂/CO ratio, is provided. Process gas composition implies that the gas is suitable for heat and power generation. Alternatively, CO₂ enhanced gasification could be considered as a carbon capture and utilization technology when external, renewable heat supply to the process is used. The results thus obtained are the initial step toward development of the CO₂ enhanced gasification process.     

Local time-averaged gas holdup in a fluidized bed with side air injection using X-ray computed tomography

Local time-averaged gas holdup in a 10.2 cm diameter fluidized bed is determined using X-ray computed tomography (CT) over a range of superficial gas velocities (U_g), side air injection flow rates (Q_side), and fluidized bed material. Without side air injection, only small variations in the local time-averaged gas holdup are observed for beds composed of glass beads, ground walnut shell, or ground corncob. With the introduction of side air injection, which simulates the immediate volatilization of biomass in a fluidized bed gasifier, a distinctive plume is observed along the reactor wall above the side injection port. The plume gradually expands toward the center of the bed as height increases; the expansion is found to increase with increasing Q_side. As U_g increases, fluidization becomes more uniform and the effect of the side air injection on the fluidization hydrodynamics is less pronounced. Additionally, increasing U_g increases overall gas holdup and bed expansion. Of the three bed materials examined, ground corncob fluidization is the least affected by side air injection and shows the highest overall gas holdup while glass bead fluidization is much more affected by side air injection and has the lowest overall gas holdup. This study demonstrates the usefulness of X-ray CT in noninvasively visualizing detailed internal features of fluidized beds. These results will be used in future studies to validate computational fluid dynamics (CFD) models of fluidized beds.     

Plastic waste elimination by co-gasification with coal and biomass in fluidized bed with air in pilot plant

Treatment of plastic waste by gasification in fluidized bed with air using dolomite as tar cracking catalyst has been studied. The gasifier has a 1 m high bed zone (diameter of 9.2 cm) followed by a 1 m high freeboard (diameter of 15.4 cm). The feedstock is composed of blends of plastic waste with pine wood sawdust and coal at flow rates of 1–4 kg/h. Operating variables studied were gasifier bed temperature (750–880 °C), equivalence ratio (0.30–0.46), feedstock composition and the influence of secondary air insertion in freeboard. Product distribution includes gas and char yields, gas composition (H₂, CO, CO₂, CH₄, light hydrocarbons), heating value and tar content in the flue gas. As a result, a gas with a medium hydrogen content (up to 15% dry basis) and low tar content (less than 0.5 g/m_n³) is obtained.     

Coal combustion characteristics in a circulating fast fluidized bed

The effect of coal size (0.73–1.03 mm), excess air ratio (1.0–1.4), operating bed temperature (750–900‡C), coal feeding rate (1–3 kg/h), and coal recycle rate (20–40 kg/h) on combustion efficiency, temperature profiles along the bed height and flue gas composition have been determined in a bubbling and circulating fluidized bed combustor (7.8 cm-ID x 2.6 m-high). Combustion efficiency increases with increasing excess air ratio and operating bed temperature and it decreases with increasing particle size in the bubbling and circulating fluidzing beds. In general, temperature profiles and combustion efficiency are more uniform and higher in a circulating bed than those in bubbling bed. Combustion efficiency also increases with increasing recycle rate of unburned coal in the circulating bed. The ratio of CO/CO₂ of flue gas decreases with increasing bed temperature and excess air ratio, whereas the ratio of O₂(CO + CO₂) decreases with bed temperature in both bubbling and circulating fluidized beds.     

Effect of biomass particle size and air superficial velocity on the gasification process in a downdraft fixed bed gasifier. An experimental and modelling study

A one-dimensional stationary model of biomass gasification in a fixed bed downdraft gasifier is presented in this paper. The model is based on the mass and energy conservation equations and includes the energy exchange between solid and gaseous phases, and the heat transfer by radiation from the solid particles. Different gasification sub-processes are incorporated: biomass drying, pyrolysis, oxidation of char and volatile matter, chemical reduction of H₂, CO₂ and H₂O by char, and hydrocarbon reforming. The model was validated experimentally in a small-scale gasifier by comparing the experimental temperature fields, biomass burning rates and fuel/air equivalence ratios with predicted results. A good agreement between experimental and estimated results was achieved. The model can be used as a tool to study the influence of process parameters, such as biomass particle mean diameter, air flow velocity, gasifier geometry, composition and inlet temperature of the gasifying agent and biomass type, on the process propagation velocity (flame front velocity) and its efficiency. The maximum efficiency was obtained with the smaller particle size and lower air velocity. It was a consequence of the higher fuel/air ratio in the gasifier and so the production of a gas with a higher calorific value.     

生物质快速热解制油试验及流程模拟

使用自主研发的流化床热解反应器对生物质热解制油进行实验研究,通过对不同实验温度450、500、525、550、580、610℃下得到的目标产物进行分析,得到了反应温度对生物油产率的影响规律。实验表明：550℃时,最大液体产率为42.5%（质量）;实验得到的不可冷凝气体的组分以CO、CO₂、CH₄和H₂为主,气相产物产率约为37.7%（质量）。在实验基础上,利用Aspen Plus流程模拟软件,建立了生物质热解制油工艺模拟流程,模拟分析了热解温度对生物油产率的影响,结果表明该模型能准确模拟实际热解过程,具有较好的适用性和可靠性。     

A novel catalytic process for cellulose gasification to synthesis gas

The catalytic gasification of cellulose to synthesis gas has been studied under mild conditions in a laboratory scale batch-feeding and fluidized bed reactor using air as a gasifying agent and Ar as a cellulose carrier from the feeder to catalyst bed under atmospheric pressure. Various types of support materials and supported metal catalysts have been investigated in this process. The flow conditions were 60 and 50 cm³ (STP)/min of air and Ar, 2 cm height of the fluidized bed and 0.7 s residence time of volatiles. From this investigation CeO₂ has been found as the best support and Rh/CeO₂ has been found as an excellent catalyst in the cellulose gasification at 823 K, which resulted in 100% C-conversion to gas. The use of Rh/CeO₂ catalyst in the secondary bed resulted in lower yield of CO and H₂.     

Effect of operating conditions on gas components in the partial coal gasification with air/steam

With increasing environmental considerations and stricter regulations, coal gasification, especially partial coal gasification, is considered to be a more attractive technology than conventional combustion. Partial coal gasification was conducted in detail under various experimental conditions in a lab-scale fluidized bed to study the factors that affected gas components and heating value, including fluidized air flow rate, coal feed rate, and steam feed rate, gasification temperature, static bed height, coal type and catalyst type. The experiment results indicate that gasification temperature is the key factor that affects components and the heating value of gas is in direct proportion to gasification temperature. There exists a suitable range of fluidized air flow rate, coal feed rate, steam feed rate and static bed height, which show more complex effect on gas components. High rank bitumite coal is much more suitable for gasification than low rank bitumite coal. The concentrations of H₂, CO and CH₄ of bitumite coal are more than those of anthracite coal. Compounds of alkali/alkaline-earth metals, such as Ca, Na, K etc., enhance the gasification rate considerably. The catalytical effects of Na₂CO₃ and K₂CO₃ are more efficient than that of CaCO₃. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Modeling of a 120 kW chemical looping combustion reactor system using a Ni-based oxygen carrier

A modeling tool for the investigation of chemical looping combustion (CLC) in a dual circulating fluidized bed (DCFB) reactor system is introduced. CLC is a novel combustion process with inherent CO₂ separation, consisting of two fluidized bed reactors, an air reactor (AR) and a fuel reactor (FR). A solid oxygen carrier (OC) that circulates between the reactors, transports the necessary oxygen for the combustion. In the DCFB concept both AR and FR are designed as circulating fluidized beds (CFBs). Each CFB is modeled using a very simple structure in which the reacting gas is only in contact with a defined fraction of the well mixed solids. The solids distribution along the height axis is defined by a void fraction profile. Different parameters that characterize the gas-solids contact are merged into only one parameter: the fraction of solids exposed to the gas passing in plug flow (φ_s,core). Using this model, the performance of the 120 kW DCFB chemical looping combustor at Vienna University of Technology is investigated. This pilot rig is designed for a Ni-based OC and natural gas as fuel. The influence of the reactor temperatures, solids circulation rate, air/fuel ratio and fuel power are determined. Furthermore, it is shown that with the applied kinetics data, the OC is only fully oxidized in the AR when the AR solids inventory is much larger than the FR solids inventory or when both reactors are very large. To compare different reactor systems, the effect of the solids distribution between AR and FR is studied and both gas and solids conversions are reported.     

Gasification characteristics of combustible wastes in a 5 ton/day fixed bed gasifier

The gasification characteristics of combustible wastes were determined in a 5 ton/day fixed bed gasifier (1.2 m I.D. and 2.8m high). The fixed bed gasifier consisted of air compressor, oxygen tank, MFC, fixed bed gasifier, cyclone, heat exchanger, solid/gas separator, water fluidized bed reactor and blower. To capture soot or unburned carbon from the gasification reaction, solid/gas separator and water fluidized bed were used. The experiments with 10–50 hours of operation were carried out to determine the effects of bed temperature, solid/oxygen ratio and oxidant on the gas composition, calorific value and carbon conversion. The calorific values of the produced gas decreased with an increase of bed temperature because combustion reaction happened more actively. The gas composition of partial oxidation of woodchip is CO: 34.4%, H₂: 10.7%, CH₄: 6.0%, CO₂: 48.9% and that of RPF is CO: 33.9%, H₂: 26.1%, CH₄: 10.7%, CO₂: 29.2%. The average calorific values of produced gas were about 1,933 kcal/Nm³, 2,863 kcal/Nm³, respectively. The maximum calorific values were 3,100 kcal/Nm³ at RPF/oxygen ratio: 7     

A novel dual circulating fluidized bed system for chemical looping processes

A fluidized bed system combining two circulating fluidized bed reactors is proposed and investigated for chemical looping combustion. Direct hydraulic communication of the two circulating fluidized bed reactors via a fluidized loop seal allows for high rates of global solids circulation and results in a stable solids distribution in the system. A 120 kW fuel power bench scale unit was designed, built, and operated. Experimental results are presented for natural gas as fuel using a nickel‐based oxygen carrier. No carbon was lost to the air reactor under any conditions operated. It is shown from fuel power variations that a turbulent/fast fluidized bed regime in the fuel reactor is advantageous. Despite the relatively low riser heights (air reactor: 4.1 m, fuel reactor: 3.0 m), high CH₄ conversion and CO₂ yield of up to 98% and 94%, respectively, can be reported for the material tested. © 2009 American Institute of Chemical Engineers AIChE J, 2009     

A comparison of the energy and product distribution from biomass gasifiers

A detailed analyses of the raw producer gas streams generated by a downdraft gasifier and by a fluidized-bed gasifier are presented and are discussed in terms of raw gas clean-up considerations and of energy conversion efficiency. The major gasifier operating parameters such as fuel/air ratio, carbon conversion efficiency, net energy conversion efficiency, and producer gas heating value are then compared between seven operational gasifiers and a computer simulation model of a fluidized-bed gasifier developed by Queen's University. It is concluded that the Queen's University model correctly predicts that the fuel/air ratio is the single most important parameter for determining gasifier performance. Downdraft gasifiers exhibit superior energy conversion efficiency and producer gas quality because they utilize a higher fuel/air ratio than do fluidized bed gasifiers.     

Co-combustion of coal and biomass in a circulating fluidized bed combustor

In this research, co-combustion of coal and rice husk was studied in a circulating fluidized bed combustor (CFBC). The effects of mixed fuel ratios, primary air and secondary air flow rates on temperature and gas concentration profiles along riser (0.1 m inside diameter and 3.0 m height) were studied. The average particle size of coal from Maetah used in this work was 1,128 mm and bed material was sand. The range of primary air flow rates was 480–920 l/min corresponding to U _g of 1.0–2.0 m/s for coal feed rate at 5.8 kg/h. The recirculation rate through L-valve was 100 kg/hr. It was found that the temperatures along the riser were rather steady at about 800–1,000 degrees Celsius. The introduction of secondary air improved combustion and temperature gradient at the bottom of the riser, particularly at a primary air flow rate below 1.5 m/s. Blending of coal with biomass, rice husk, did improve the combustion efficiency of coal itself even at low concentration of rice husk of 3.5 wt%. In addition, the presence of rice husk in the feed stocks reduced the emission of both NO _x and SO₂.     

Coal combustion characteristics in a fluidized bed combustor with a draft tube

The effects of gas velocity to draft tube (3–6 U_m), bed temperature (800–900°C) and excess air ratio (0–30%) on the total entrainment rate, overall combustion efficiency and heat transfer coefficient have been determined in an internally circulating fluidized bed combustor with a draft tube. The total entrainment rate increases with an increase in gas velocity to draft tube, but decreases with increasing bed temperature and excess air ratio. The overall combustion efficiency increases with increasing excess air ratio, but decreases with increasing gas velocity to draft tube. The overall combustion efficiency obtained in internally circulating fluidized beds was found to be somewhat higher than that in a bubbling fluidized bed combustor.