Influence of the Physical Structure of Flax Fibres on the Mechanical Properties of Flax Fibre Reinforced Polypropylene Composites

This study investigates the influence of the physical structure of flax fibres on the mechanical properties of polypropylene (PP) composites. Due to their composite-like structure, flax fibres have relatively weak lateral bonds which are in particular present in flax fibres that are often used in natural fibre mat reinforced thermoplastics (NMT). These weak bonds can be partly removed by combing the fibres. In order to study the influence of the physical structure of flax fibres on NMT tensile and flexural properties, uncombed and combed flax fibre reinforced PP composites were manufactured via a wet laid process. The influence of improved fibre-matrix adhesion was studied using maleic-anhydride grafted PP. Results indicated that the flax physical structure has a significant effect on flax-PP composite properties and that the flax fibre reinforced PP properties are similar to values predicted with existing micromechanical models. The tensile modulus of flax-PP composites can fairly compete with commercial glass mat reinforced thermoplastic (GMT) modulus, the strength, however, both tensile and flexural, can not. In order to rise the strength of flax fibre reinforced PP composites to the level of GMT strength, the flax fibres have to be further isolated to elementary flax fibres.     

Reinforcement of polypropylene with hemp fibres

Noil hemp fibre (NHF) is a kind of textile hemp fibre after deep degumming from scutched hemp fibre (SHF), mechanically-degummed hemp fibre. Both NHF and SHF with strong mechanical properties are good candidates as reinforcing fibres for plastics such as polypropylene (PP). The PP/NHF and PP/SHF composites were blended via internal mixing process. The effect of fibres on the morphology, thermal resistance and reinforcement of the composites were investigated. PP/NHF composites showed higher impact strength, lower flexural strength than PP/SHF at the corresponding loading because NHF has smaller diameter and better thermal resistance than SHF. Meanwhile, NHF has the similar reinforcement to tensile strength with SHF. The effect of maleic anhydride polypropylene (MAPP) on the fibre-resin interface bonding was also comparatively studied. With increasing amount of MAPP, the tensile, flexural and impact strengths of PP/NHF and PP/SHF increased, respectively. The morphology of PP/SHF and PP/NHF results well showed that MAPP improved the interaction of the fibres with PP through chemical adhesion.     

Composite materials based on wood and nylon fibre

Nylon-wood fibre and polypropylene-wood fibre composite materials were manufactured without any additives to determine the effects of wood fibre on the mechanical properties of the different composites. The raw materials used were eucalypt hardwood fibre, Nylon fibre obtained from stockings, and polypropylene (PP) pellets. A hot press technique was used to manufacture the composite materials, and improvements in the manufacturing methods are suggested. Tests were carried out on the manufactured boards to determine tensile strength and modulus of elasticity. Fracture surfaces were examined using scanning electron microscopy to investigate failure mechanisms. An increase in tensile strength and modulus of elasticity was observed in wood fibre/Nylon matrix composites, indicating that interfacial bonding occurred between these two phases. Bundles of wood fibres with internal voids prevent achieving maximum mechanical properties. The tensile strength of the PP based composites decreased significantly with increasing wood fibre content.     

Preparation and properties of polypropylene composites reinforced with wheat and flax straw fibres: Part II Analysis of composite microstructure and mechanical properties

The microstructure and mechanical properties of polypropylene composites containing flax and wheat straw fibres are discussed. Particular emphasis has been given to determining the nature and consequences of fibre damage induced during melt-processing operations, fibre orientation occurring in mouldings, and possible interfacial adhesion between the matrix and fibres. Compared to unfilled polypropylene, addition of flax and wheat straw caused a significant increase in tensile modulus, particularly, in the case of flax fibres, which also gave higher tensile yield strength and Charpy toughness, despite a lack of interfacial bonding. Tensile strength was increased further through inclusion of 5% by weight of maleic anhydride-modified polypropylene, which was shown to promote adhesion between fibres and matrix. This revised version was published online in November 2006 with corrections to the Cover Date.     

A novel processing technique for thermoplastic manufacturing of unidirectional composites reinforced with jute yarns

This paper primarily investigates the fabrication process of long-fibre reinforced unidirectional thermoplastic composites made using jute yarns (both untreated and treated). Tubular braiding technique was used to produce an intermediate material called “microbraid yarn” (MBY) with jute yarn as the straightly inserted axial reinforcement fibre and polymer matrix fibre being braided around the reinforcing jute yarns. Microbraid yarns were then wound in a parallel configuration onto a metallic frame and compression molded to fabricate unidirectional composite specimens. In this study, two types of polymeric materials (biodegradable poly(lactic) acid and non-biodegradable homo-polypropylene) were used as matrix fibres. Basic static mechanical properties were evaluated from tensile and 3 point bending tests. Test results were analyzed to investigate the effects of molding temperature and pressure on the mechanical and interfacial behaviour. For the unidirectional jute fibre/poly(lactic) acid (PLA) composites, the results indicated that the molding condition at 175 °C and 2.7 MPa pressure was more suitable to obtain optimized properties. Improved wettability due to proper matrix fusion facilitated thorough impregnation, which contributed positively to the fibre/matrix interfacial interactions leading to effective stress transfer from matrix to fibre and improved reinforcing effects of jute yarns. For the jute/PP unidirectional composites, specimens with only 20% of jute fibre content have shown remarkable improvement in tensile and bending properties when compared to those of the virgin PP specimens. The improvements in the mechanical properties are broadly related to various factors, such as the wettability of resin melts into fibre bundles, interfacial adhesion, orientation and uniform distribution of matrix-fibres and the lack of fibre attrition and attenuation during tubular braiding process.     

Mechanical property and hydrothermal aging of injection molded jute/polypropylene composites

This study discussed the effects of jute fiber content and hot water immersion on the tensile properties of jute fiber reinforced polypropylene (PP) composites. The jute/PP composite with different fiber contents was molded by injection molding by dry-blending of jute/PP and neat PP pellets in various mix ratios. Firstly, the quasi-static tensile test was performed. Then the specimens were aged in hot distilled water at 80 °C. After the fixed periods of aging, the changed weight and the tensile properties were investigated. It is found that with the increase of the jute fiber content, the tensile modulus is increased lineally. However, referring to the tensile strength, it is increased firstly followed by a decreased when the jute weight percent is over 30. Additionally, it is found that the weight gain by water absorption was significantly affected by the fiber content. The specimens with the jute fiber content of or over 30 wt% absorbed water easily and significant material loss by aging was also occurred. The tensile strength after aging decreased remarkably in these specimens with the jute fiber content of or over 30 wt%, and all the jute/PP composites showed the lower strength than neat PP after the aging of 1000 h. It is considered that the hydrophilic property of natural fiber decreases the resistance of the composite in humidity environment.     

Effect of coupling agents on reinforcing potential of recycled carbon fibre for polypropylene composite

Polypropylene (PP) composites reinforced with recycled carbon fibre have been prepared through extrusion compounding and injection moulding. The reinforcing potential of the recycled fibre was increased by improving the interfacial adhesion between the fibre and PP matrix and this was done by the addition of maleic anhydride grafted polypropylene (MAPP) coupling agents. Three MAPP couplers with different molecular weights and maleic anhydride contents were considered. The effects on the mechanical properties of the composite were studied, and scanning electron microscopy (SEM) was used to study the fracture morphology of the tensile specimens. It was observed that with the addition of MAPP the interfacial adhesion was improved as fewer fibres were pulled-out and less debonding was seen. A microbond test was performed and a significant improvement in interfacial shear strength was measured. This resulted in composites with higher tensile and flexural strengths. The maximum strength was achieved from MAPP with the highest molecular weight. Increased modulus was also achieved with certain grades of MAPP. It was also found that the composite impact strength was improved significantly by MAPP, due to a higher compatibility between the fibre and matrix, which reduced crack initiation and propagation.     

Role of film formers in glass fibre reinforced polypropylene — new insights and relation to mechanical properties

The adhesion strength between reinforcing glass fibres and polypropylene matrix can be improved by introduction of acidic groups due to matrix modification and by creation of a strong interphase between the components. In this paper, we consider two different sizings consisting of γ-aminopropyltriethoxysilane (APS) as silane coupling agent and either polyurethane (PU) dispersion or polypropylene (PP) dispersion as film former.The adhesion strength determined using pull-out tests showed a strong dependence on the film former. Both the variation of adhesion strengths and interphase modulus determined using nanoindentation were found to be consistent with the macromechanical properties of glass fibre reinforced polypropylene. The interphase design provided simultaneous increase in the tensile strength and the impact toughness of the composites. The results of acoustic emission and fractography confirm the different performance due to the interphase design. Failure mechanisms such as matrix deformation and fibre matrix debonding influenced by the different film formers proved to be the origin of different mechanical results, whereas fibre tensile strengths did not differ.     

Continuous-glass-fibre-reinforced polypropylene composites: I. Influence of maleic-anhydride-modified polypropylene on mechanical properties

This study investigates the influence of maleicanhydride-modified polypropylene (m-PP) on monotonic mechanical properties of continuous-glass-fibre-reinforced polypropylene (PP) composites. Maleicanhydride-modified polypropylene was added to the PP homopolymer to improve the adhesion between the matrix and the glass fibre. Three-point bending tests were performed on 0° and 90° unidirectional glass-fibre/PP laminates with various weight fractions of m-PP in the PP matrix. These tests showed an increase in both longitudinal and transverse flexural strength up to 10 wt% m-PP, whereas at higher weight fractions of m-PP a decrease in flexural strength was observed. No significant influence of m-PP on composite stiffness was observed. Additional mechanical tests on unidirectional glass/PP composites with 0 wt% and 10 wt% m-PP showed only a small increase in fibre-dominated properties such as longitudinal tensile strength and strain, whereas composite properties that are governed by the interphase, such as transverse, shear and compressive strength, showed significant increases as a result of matrix modification and an enhanced interaction between the glass fibres and the PP matrix.     

Polyolefin composites with curaua fibres: Effect of the processing conditions on mechanical properties,morphology and fibres dimensions

Composites of polypropylene (PP) and high density polyethylene (HDPE) reinforced with 20 wt.% of curaua fibres were prepared using a twin-screw extruder and the effect of screw rotation speed (SRS) was evaluated by measuring the output, the mechanical properties of the composites, the morphology and the fibre dimensions. Increase in SRS causes a decrease in length, diameter and aspect ratio of the fibres in both composites, due to the high shear forces acting in the molten polymer and transferred to the fibres. Consequently, the reinforcement effect of the fibres decreased, as evidenced by the flexural and tensile mechanical properties of the composites. Additionally, polymeric matrices undergoes thermo-mechanical degradation during processing, this also contributed to the changes in the mechanical properties. Comparison between the matrices showed that PP composites are less affected by changes in SRS, suffering fewer changes in fibre dimensional parameters and in the mechanical properties than HDPE composites.     

Mechanical Properties of Natural-Fibre-Mat- Reinforced Thermoplastics based on Flax Fibres and Polypropylene

Thermoplastic composites based on flax fibres and a polypropylene (PP) matrix were manufactured using (i) a film-stacking method based on random fibre mats and (ii) a paper making process based on chopped fibres. The influence of fibre length and fibre content on stiffness, strength and impact strength of these so-called natural-fibre-mat-reinforced thermoplastics (NMTs) is reported and compared with data for glass-mat-reinforced thermoplastics (GMTs), including the influence of the use of maleic-anhydride grafted PP for improved interfacial adhesion. In addition some preliminary data on the influence of fibre diameter on composite stiffness and strength is reported. The data is compared with the existing micro-mechanical models for strength and stiffness. A good agreement was found between theory and experiment in case of stiffness whereas in the case of strength the experimental values fall well below the theoretical predictions. Results indicated that NMTs are of interest for low-cost engineering applications and can compete with commercial GMTs when a high stiffness per unit weight is desirable. Results also indicated that future research towards significant improvements in tensile and impact strength of these types of composites should focus on the optimisation of fibre strength rather than interfacial bond strength.     

Extrusion and mechanical properties of highly filled cellulose fibre–polypropylene composites

This study focused on manufacturing of highly filled cellulose fibre–polypropylene composites and evaluation of the mechanical properties of the composites. Cellulose fibre reinforced polypropylene composites with up to 60 wt% of fibres with and without coupling agent were manufactured by extrusion. In order to achieve consistent feeding of the fibres into the extruder a pelletization technique was used where the fibres were pressed into pellets. Two commercial grades of cellulose fibres were used in the study, bleached sulfite and bleached kraft fibres. Fibre dimension measurements showed that the pelletization process and extrusion at high fibre loading caused the most severe fibre breakage. Flexural testing showed that increased fibre loading made the composites stiffer but reduced the toughness. Addition of maleic anhydride grafted coupling agent (MAPP) increased the stiffness and strength of the composites significantly. In general, there was no significant difference in the mechanical properties between the composites with kraft and sulfite fibres. An interesting finding was that the flexural modulus and strength of the MAPP modified cellulose fibre–polypropylene composites were not higher than what has previously been reported for wood flour–polyolefin composites. Scanning electron microscopy showed that addition of coupling agent improved the interfacial adhesion between the fibres and polypropylene matrix.     

Isocyanate as a compatibilizing agent on the properties of highly crystalline cellulose/polypropylene composites

Composites of a highly crystalline cellulosic microfibres with polypropylene (PP) as well as with maleic anhydride grafted polypropylene (MAPP) were prepared by using 1,6-diisocyanatohexane (DIC) as a compatibilizing agent, their mechanical properties, morphologies, and thermal properties were investigated. Results show that the tensile strength and young’s modulus of the composites improved intensively by using DIC. The enhancement is proposed to be due to stronger interfacial adhesion caused by the reduction of the polarity and hydrophilicity of cellulose fiber in PP-based composites, while much more chemically bound MAPP chains on cellulose fiber in MAPP-based composites. A maximum on tensile properties of the composite can be obtained by optimizing of the DIC content. Scanning electron microscopy (SEM) indicates that the interfacial adhesion between cellulose fibers and PP or MAPP matrix was improved in DIC coupled composites. Furthermore, DIC yields also some effects on thermal dynamic mechanical properties, as well as melting and crystallization behavior of the composites.     

Fabrication and mechanical properties of aramid/nylon plain knitted composites

The presence of fibre/matrix interfaces strongly influences the overall mechanical properties of composites. In order to produce fully recyclable fiber reinforced composites with improved adhesion properties, polyethylene and polypropylene materials were previously used as single-polymer composite materials. In this paper, another breed of single-polymer composite material has been defined as the ‘one-unity’ composite. Polyamide materials were chosen and combined with aramid fibre in an attempt to achieve better interfacial bonding. Weft-knitting technique was used to produce textile reinforcements for aramid/nylon composite processing. Aramid/epoxy knitted composites were also fabricated to compare them with aramid/nylon thermoplastic composites. Mechanical properties of aramid/nylon and aramid/epoxy composites and their relationships to the fibre/matrix interfacial adhesion and interactions have been investigated. With the increase in processing time, tensile modulus and strength of aramid/nylon composites have increased and decreased, respectively. Furthermore, scanning electron microscopic observations clearly indicated that longer molding time has resulted in stronger adhesion property between fiber and matrix. Aramid/nylon knitted composites have revealed comparable strength property in the course direction, albeit they have inferior tensile strength in the wale direction when compared to that in aramid/epoxy composites. In aramid/nylon knitted composites, while tensile modulus exhibited an increasing trend, there were clear drops in tensile strengths with longer molding time. This indicates that there could be an optimum molding condition at which maximum tensile properties can be obtained. Aramid/nylon knitted composites exhibited relatively better interfacial bonding properties than Aramid/epoxy composites, which suffered fibre/matrix debonding.     

Determination of interfacial shear strength of white rot fungi treated hemp fibre reinforced polypropylene

Short untreated and white rot fungi treated hemp fibre, polypropylene (PP) and maleated polypropylene (MAPP) coupling agent were extruded and injection moulded into composite tensile test specimens. The tensile properties of untreated and treated fibre and their composites were measured. The fibre length distributions in the composite were obtained by dissolving the PP/MAPP matrix in boiling xylene to extract the fibre. Both the Single Fibre Pull-Out test and the Bowyer and Bader model were used to determine the interfacial shear strength (IFSS) of these composites. IFSS was found to be lower for the Single Fibre Pull-Out test, which was considered to be largely due to axial loading of fibre and the resulting Poisson’s contraction occurring during this technique. This suggests that the Bowyer and Bader model provides a more relevant value of IFSS for composites. The results obtained from both methods showed that IFSS of the treated fibre composites was higher than that for untreated fibre composites. This supports that the hemp fibre interfacial bonding with PP was improved by white rot fungi treatment.     

纤维表面处理与基体改性对连续玻纤增强聚丙烯力学性能的影响

考察了连续玻纤的表面处理、基体的接枝改性及接枝单体的种类和接枝产物的加入量对连续玻纤毡增强聚丙烯(CGFRPP) 力学性能的影响, 并通过红外光谱、扫描电镜对CGFRPP 的界面化学作用及界面粘结进行了研究。结果表明, 马来酸酐接枝改性聚丙烯与未经偶联剂处理的玻纤不能形成有效的化学结合, 而与经硅烷偶联剂表面处理的玻纤可发生明显的化学作用, 形成良好粘结, 显著提高CGFRPP 的力学性能; 硅烷偶联剂的种类对以改性PP 为基体的CGFRPP 力学性能的影响不大; 马来酸酐接枝聚丙烯比丙烯酸接枝聚丙烯对CGFRPP 力学性能的改善更为有效。      

Date palm wood flour/glass fibre reinforced hybrid composites of recycled polypropylene: Mechanical and thermal properties

Recycled polypropylene (RPP) based hybrid composites of date palm wood flour/glass fibre were prepared by different weight ratios of the two reinforcements. Mixing process was carried out in an extruder and samples were prepared by injection molding machine. Recycled PP properties were improved by reinforcing it by wood flour. The tensile strength and Young’s modulus of wood flour reinforced RPP increased further by adding glass fibre. Glass fibre reinforced composites showed higher hardness than other composites. Morphological studies indicated that glass fiber has good adhesion with recycled PP supporting the improvement of the mechanical properties of hybrid composites with glass fiber addition. Addition of as little 5 wt% glass fibre to wood flour reinforced RPP increases the tensile strength by about 18% relative to the wood flour reinforcement alone. An increase in wood particle content in the PP resulted in a decrease in the degree of crystallinity of the polymer. The tensile strength of the composites increased with an increase in the percentage of crystallinity when adding the glass fibre. The improvement in the mechanical properties with the increase in crystallinity percentage (and with the decrease of the lamellar thicknesses) can be attributed to the constrained region between the lamellae because the agglomeration is absent in this case.     

Could biopolymers reinforced by randomly scattered flax fibre be used in structural applications?

Thermoplastics reinforced by natural fibres are mainly used for fitting-up products in the automotive industry. The aim of this work is to study the tensile properties of natural fibre-biopolymer composites in order to determine whether or not, biocomposites may replace glass fibre reinforced unsaturated polyester resins. The materials used are flax fibre, polylactic acid (PLA), l-polylactide acid (PLLA), poly(3-hydroxylbutyrate) (PHB), polycaprolactone and starch thermoplastic (MaterBi® Z), poly(butylene succianate) (PBS) and poly(butylene adipate-co-terephtalate) (PBAT). The tensile properties of the flax fibres have already been determined [C. Baley, Analysis of the flax fibres tensile behaviour and analysis of the tensile stiffness increase, Comp Part A 2002;33:939–948]. The composites are manufactured using a film stacking technique. After studying the processing parameters, these are then adapted to each thermoplastic composites. Test samples are cut out from the composites to test their mechanical properties under tensile loading conditions. These tensile properties are then compared to those of similar polypropylene flax composites. Preliminary results show that the tensile properties are improved with the fibre volume fraction. The tensile strength and Young’s modulus of PLLA and PLA flax composites are greater than those of similar PP/flax fibre composites. The specific tensile strength and modulus of flax fibre/PLLA composite have proved to be very close to those of glass fibre polyester composites.     

Characteristics of several carbon fibrereinforced aluminium composites prepared by a hybridization method

The properties and microstructures of several high-strength and high-modulus carbon fibrereinforced aluminium or aluminium alloy matrix composites (abbreviated as HSCF/Al and HMCF/Al, respectively, for the two types of fibre) have been characterized. The composites evaluated were fabricated by pressure casting based on a hybridization method. It was found that the strength degradation of high-modulus carbon fibres after infiltration of aluminium matrices was not marked and depended upon the type of aluminium matrix. However, the strength of high-strength carbon fibres was greatly degraded by aluminium infiltration and the degradation seemed to be independent of the type of aluminium matrix. The longitudinal tensile strength (LTS) of CF/Al composites was very different between HMCF/Al and HSCF/Al composites. The HMCF/Al composites had LTS values above 800 MPa, but the HSCF/Al composites had only about 400 MPa. In contrast, the transverse tensile strength of the HSCF/Al composites, above 60 MPa, was much higher than that of the HMCF/Al composites, about 16 MPa. Chemical reactions were evident to the interface of high-strength carbon fibres and aluminium matrices. There was no evidence of chemical products arising between high-modulus carbon fibres and Al-Si alloy and 6061 alloy matrices. However, it was considered that some interfacial reactions took place in pure aluminium matrix composites. Fracture morphology observation indicated that the good LTS of CF/Al composites corresponded to an intermediate fibre pull-out, whereas a planar fracture pattern related to a very poor LTS and fibre strength transfer. The results obtained suggested that interfacial bonding between carbon fibres and aluminium matrices had an important bearing on the mechanical properties of CF/Al composites. An intermediate interfacial bonding is expected to achieve good longitudinal and transverse tensile strengths of CF/Al composites.     

Analysis of Mechanical Properties of Injection Molded Short Glass Fibre (SGF)/Calcite/ABS Composites

Acrylonitrile-butadiene-Styrene (ABS), with and without calcium carbonate (calcite) particles,was used as the matrix for reinforcement with as-received short-glass fibres (were originallytreated by the manufacturer) and sized short-glass fibres with two amino-silane coupling agents.The calcite particle content is 0, 11.7 and 23.5 vol. pct for the matrices. The glass fiber contentis 0, 10 and 15 vol. pct. The matrix materials and corresponding composites were compoundedusing a twin screw extruder and dumbbell-shaped tensile bars were prepared with an injectionmolding process. The tensile and flexural properties as well as the unnotched and notchedCharpy impact energies of short glass fibre/calcite/ABS composites were studied in this paper.The effects of fibres, fibre surface treatments and particles on these mechanical properties ofthe composites were discussed in detail. An importarit information was obtained, which is thatthe tensile and flexural strengths of hybrid SGF/calcite/ABS composites are the same as thoseof corresponding fibre composites when the ratio of the interfacial adhesion strength betweenparticles and matrix to that between fibres and matrix is higher than certain value. otherwise theformer are lower than the latter.