Numerical simulation of molding-defect formation during resin transfer molding

The present study investigated a numerical simulation of molding-defect formation during resin transfer molding using boundary element method and line dynamics. The proposed method enables to simulate small molding defects by increasing the node for required position during time evolution; thereby, the method computes high-resolution flow front without being affected by the initial mesh geometry. The method was applied to the radial injection RTM with single inlet, and it was confirmed by comparison with theoretical value based on Darcy’s law that the flow advancement was computed with high accuracy. In addition, the method was also applied to the flow advancement for inclusion problem with cylinder, and four-point injection problem. The simulated flow behavior, void formation, and shrinkage agreed with the results in references. Finally, the method was compared with experiments using two-point injection problem. The computed configuration of the flow front and weld line agreed well with the experimental results.     

缝合夹层结构复合材料树脂传递模塑成型工艺充模仿真

对复合材料与金属经缝合连接形成的夹层结构板的树脂传递模塑成型（RTM）工艺进行了充模模拟研究。首先通过实验和数值计算的方法,分别获得缝合夹层结构织物和芯层孔洞的渗透率;随后,建立能够反映缝孔内流动情况的二维和三维简化模型,进行RTM充模仿真,讨论不同工艺参数对成型流动的影响;最后通过成型实验验证工艺的可行性。缝线与孔洞直径之比为0.3~0.8时,孔洞渗透率随缝线直径的增大而减小,预制体织物渗透率与孔洞渗透率相差两个数量级;缝孔内容易产生缺陷,没有缺陷的区域随着注射压力的增加、孔洞密度和芯层厚度的减小而增大,在芯层表面沿每排孔洞单向开槽能够改善树脂在孔洞内的浸润;线注射时,树脂整体流动情况优于点注射,而点注射时,将进胶口设置在一角,能够减少表面干斑。     

Three-dimensional process cycle simulation of composite parts manufactured by resin transfer molding

A process cycle of resin transfer molding (RTM) consists of two sequential stages, i.e. filling and curing stages. These two stages are interrelated in non-isothermal processes so that the curing stage is dominated by the resin flow as well as temperature and conversion distributions during the filling stage. Therefore, it is necessary to take into account both filling and curing stages to analyze the process cycle accurately. In this paper, a full three-dimensional process cycle simulation of RTM is performed. Full three-dimensional analysis is necessary for thick parts or parts having complex shape. A computer code is developed based on the control volume/finite element method (CV/FEM). The resulting computer code can provide information regarding flow progression and pressure field during mold filling; and temperature distribution and degree of cure distribution for a process cycle. The computer code can also be used for process cycle simulation of composite structures with complex geometry and with various molding strategies including switching injection strategy, multiple gate injection strategy and variable mold wall temperature. Numerical examples provided in the present work show the capabilities of the computer code in analyzing the process cycle.     

树脂传递模塑过程的数学描述和数值模拟进展

树脂传递模塑(resin transfer molding,RTM)过程的数值模拟对于优化工艺参数和模具设计、控制制品质量等具有重要意义.本文简述了RTM工艺的流体流动特点,介绍了RTM工艺过程数值模拟的理论基础,综述了RTM工艺过程数值模拟的发展历程,并展望了其发展趋势.     

基于VOF/PLIC界面追踪方法的RTM工艺充模过程数值模拟

针对基于Darcy定律的树脂传递模塑(RTM)工艺的充模过程数值模拟的局限性,将纤维预制体内的充填流动作为两相流(树脂相和空气相)处理,在动量方程中考虑了惯性项和粘性项,采用有限体积方法(FVM)离散控制方程,并与VOF/PLIC界面追踪方法相结合,发展了求解树脂在纤维预制体内非稳态流动问题的数值模拟方法.在此基础上开发了RTM工艺的充模过程数值模拟程序,其算例的数值模拟结果与解析解或实验结果吻合良好,验证了此数值模拟方法的有效性和可靠性.     

Application of level set method in simulation of surface roughness in nanotechnologies

One of the limiting factors in applications of plasma etching in nanotechnologies in general will be the control of plasma induced roughness or perhaps control of surface roughness by plasma etching. In this paper we consider roughening of nanocomposite materials during plasma etching for two etching modes (isotropic and anisotropic) by using a level set method. It was found that the presence of two phases with different etch rates (the ratio of the two etch rates is s and the abundance of one phase is p) affects the evolution of the surface roughness and that the etch rate is higher during the isotropic process as compared to the anisotropic process for all values of s and p. At the same time, in case of isotropic process, the higher s leads to a higher overall etch rate. The obtained results apart from their theoretical relevance, have practical implications for surface treatment of nanocomposite materials.     

Interlayer toughening of resin transfer molding composites

In previous research it was shown that through using preformed elastomer particle modified tackifier/binder, materials interlayered RTM composite structures could be manufactured. These interlayers resulted in excellent toughness improvements of traditionally brittle RTM materials. In this work, the effects of tackifier application and composition were investigated by modifying spray and powder epoxy tackifiers with polyamide 6 particles. The spray tackifier provided 30% improvements in Mode II interlaminar fracture toughness, and slight increases in the interlaminar shear strength without reducing the thermal properties. The powder tackifier showed a slightly lower performance increase due to a less homogeneous laminate structure.     

All-polyamide composites prepared by resin transfer molding

Resin transfer molding (RTM) was used to manufacture all-polyamide (all-PA) composites in which PA6 matrix was in situ formed by the anionic polymerization of ε-caprolactam (CL). Influence of molding temperature (T _M), a critical process parameter, on the structure and properties of all-PA composites was investigated using TGA, DSC, SEM, and tensile, flexural test. Increasing T _M resulted in the decrease of CL conversion and the enhancement of fiber/matrix interface bonding. By comparing the mechanical properties of all-PA composites prepared at different T _M (140–200 °C), an optimal T _M (180 °C) was found in this temperature range. As a whole, the complete consolidation of all-PA composites and the remarkable reinforcing effect of PA66 fibers on PA6 matrix were assured by low-void fraction, high-CL conversion and strong interface performance though in a wide T _M range.     

新型树脂传递模塑技术

概述了传统树脂传递模塑(RTM)及在其基础上发展起来的新型RTM工艺,包括真空辅助树脂传递模塑(VARTM)、Seemann复合材料树脂浸渍模塑成型工艺(SCRIMP)和树脂膜渗透成型工艺(RFI)的成型原理、优点,并指出目前存在的缺点及解决方法.     

Analysis of vacuum bag resin transfer molding process

An analytical model is developed to analyze the resin flow through a deformable fiber preform during vacuum bag resin transfer molding (VBRTM) process. The force balance between the resin and the fiber preform is used to account for the swelling of fiber preform inside a flexible vacuum bag. Mold filling through multiple resin inlets is analyzed under different vacuum conditions. The formation of dry spots is demonstrated in the presence of residual air. Molding of a three-dimensional ship hull with lateral and longitudinal stiffeners is simulated to demonstrate the applicability of the model.     

树脂传递模塑成型工艺中嵌套效应引起渗透率变异的实验与数值模拟

树脂传递模塑成型工艺(RTM)中最重要的变形模式之一是厚度方向压缩。厚度方向压缩减小了织物预成型体的厚度,使织物预成型体局部结构形式发生改变从而引起嵌套效应。嵌套效应不仅会减少织物预成型体的厚度,增加纤维的体积分数并改变孔隙率,而且相邻织物层嵌套效应具有一定的空间分散性,从而使得织物预成型体渗透率具有变异性。本文针对低黏度树脂设计了一种实验装置用以测量局部渗透率的空间分散性,随后建立了随机嵌套单胞模型,利用ANSYS/CFX有限元软件实现了单胞填充浸润的数值模拟,通过流量分析获得局部渗透率,并研究了渗透率的统计分布。通过实验结果与数值模拟结果相对比,验证数值模拟结果的可靠性。最后,基于渗透率的统计分布建立了随机渗透率场,并进行填充浸润的数值模拟,通过与传统恒定渗透率的方法进行比较,证明该方法具有更高的先进性。研究结果可以对未来RTM工艺的稳健性优化提供依据。      

Application of calcium carbonate in resin transfer molding process: An experimental investigation

The resin transfer molding (RTM) process is used to manufacture advanced composite materials made of continuous glass or carbon fibers embedded in a thermoset polymer matrix. In this process, a fabric preform is prepared, and is then placed into a mold cavity. After the preform is compacted between the mold parts, thermoset polymer is transferred from an injection machine to the mold cavity through injection gate(s). Resin flows through the porous fabric, and eventually flows out through the ventilation port(s). After the resin cure process (cross‐linking of the polymer), the mold is opened and the part is removed. The objective of this study is to verify the application of calcium carbonate mixed in resin in the RTM process. Several rectilinear infiltration experiments were conducted using glass fiber mat molded in a RTM system with cavity dimensions of 320 × 150 × 3.6 mm, room temperature, maximum injection pressure 0.202 bar and different content of CaCO₃ (10 and 40%) and particle size (mesh opening 38 and 75 µm). The results show that the use of filled resin with CaCO₃ influences the preform impregnation during the RTM molding, changing the filling time and flow front position, however it is possible to make composite with a good quality and low cost.     

Repair of underground buried pipes with resin transfer molding

Repairing and replacing of worn-out underground pipes, such as sewer pipes, water-supply pipes, gas pipes, and communication cables by excavating not only cause traffic congestion but also produce large amount of waste. Also, the operation requires heavy equipments and longer operating time and high cost.

In this study, the repairing–reinforcing process of underground pipes with glass fiber fabric polymer composites using resin transfer molding (RTM) which overcomes the problems of present trenchless technologies has been developed. The developed process requires shorter operation time and lower cost with smaller and simpler operating equipments than conventional trenchless technologies. For the faultless operation, a simple method to apply pressure and vacuum to the reinforcement was developed. The resin wetting and void removal during RTM process for very large and long-composite buried pipes were experimentally investigated, and the efficient void removal method was suggested. Cure status and resin filling were monitored with a commercial dielectrometry cure monitoring system, LACOMCURE.

From the investigation, it has been found that the developed repair technology with appropriate process parameters and on-line cure monitoring has many advantages over conventional methods.     

A grid of dielectric sensors to monitor mold filling and resin cure in resin transfer molding

A grid of 50 dielectric sensors has been embedded in the walls of a mold to monitor resin transfer molding (RTM). The capacitance of each sensor increased as resin occupied the space between sensor plates, and it decreased with curing. Monitoring data can be used for process control to prevent dry spots and to determine when to de-mold the part. In previous studies, Skordos et al. [Skordos AA, Karkanas PI, Partridge IK. A dielectric sensor for measuring flow in resin transfer molding. Meas Sci Technol 2000;11:25–31] used a lineal sensor, Hegg et al. [Hegg MC, Ogale A, Mescher A, Mamishev AV, Minaie B. Remote monitoring of resin transfer molding processes by distributed dielectric sensors. J Compos Mater 2005;39(17)] used three large sensors. As experimentally shown in this study, these lineal or large-plate dielectric sensors may mislead since a sensor measures total fraction of the sensor’s plate area occupied by resin but not the resin’s whereabouts. To avoid ambiguity and yet maintain detailed monitoring, a sensor grid was made at the projections of embedded orthogonal electrodes. The developed sensor operation system eliminated tedious and costly manufacturing of conventionally shielded separate sensors. The success of the developed sensor system was demonstrated in RTM experiments.     

Data assimilation through integration of stochastic resin flow simulation with visual observation during vacuum-assisted resin transfer molding: A numerical study

This study investigated data assimilation through integration of visual observation with a stochastic numerical simulation of resin flow during vacuum-assisted resin transfer molding. The data assimilation was performed using the four-dimensional asynchronous ensemble square root filter and a stochastic numerical simulation by means of the Karhunen–Loève expansion of the permeability field. Through numerical experiments of linear flow, it was verified that the estimation accuracy of the resin impregnation behavior improved compared to that when using conventional data assimilation and that the permeability field could be estimated simultaneously, although it is not explicitly related to the observation. We also investigated the applicability of the proposed method to radial-injection VaRTM by varying the model thickness. The proposed method successfully estimated the resin impregnation behavior and permeability field. Additionally, the required condition for the number of ensemble members was clarified.     

Forming characteristics during the high-pressure resin transfer molding process for CFRP

The high-pressure resin transfer molding (HP-RTM) process has potential applicability to the mass production of lightweight vehicles made of carbon fiber-reinforced plastic in the automotive industry. In recent years, the development of robust equipment, new processes, and fast cure matrix systems have significantly reduced the cycle time to less than 5 min. In this study, the cavity pressure of the HP-RTM process was monitored to analyze the molding characteristics. The mold was equipped with two cavity pressure sensors and three temperature sensors. The cavity pressure characteristics during the HP-RTM injection, pressurization, and curing processes were studied. Selected process parameters such as the mold cap size, maximum pressing force, and injection volume were analyzed. The results demonstrated correlations between the selected process parameters and final forming characteristics.     

Monitoring of resin flow in the resin transfer molding (RTM) process using point-voltage sensors

Multiple point-voltage sensors were used to monitor the mold filling stage of the resin transfer molding (RTM) process. Both lineal- and point-voltage sensors are electrical circuits in which the two poles of the sensor are closed when liquid thermoset resin arrives at the sensor location in the mold cavity. The electrical conductance of the liquid resin causes an increase in the output voltage, V_sens of the circuit. Although the gradually varying in situ data of a lineal sensor is more informative than a point-voltage sensor, lineal-voltage sensors might mislead the user if the resin covers the wires at multiple sections, or if the resin covers the wires starting from an unexpected section. Two kinds of sensors were developed: a set of similar, wrapped and compact lineal-voltage sensors acting as point-voltage sensors; and a point-voltage sensor with voltage amplification. Without this amplification, the increase in V_sens might be difficult to detect if the resin system has a low electrical conductivity and there is noise in the DAQ system. The accuracy and reliability of the new sensor system was verified by comparing the in situ sensor data with the visually recorded resin flow.     

Simulation of the three-dimensional non-isothermal mold filling process in resin transfer molding

Numerical simulation of resin transfer molding (RTM) is known as a useful method to analyze the process before the mold is actually built. In thick parts, the resin flow is no longer two-dimensional and must be simulated in a fully three-dimensional space. This article presents numerical simulations of three-dimensional non-isothermal mold filling of the RTM process. The control volume/finite element method (CV/FEM) is used in this study. Numerical formulation for resin flow is based on the concept of nodal partial saturation at the flow front. This approach permits to include a transient term in the working equation, removing the need for calculation of time step to track the flow front in conventional scheme. In order to compare the results of the nodal partial saturation concept with the conventional method, a numerical scheme based on the quasi-steady state formulation is also presented. The computer codes developed based on both numerical formulations, allow the prediction of flow front positions; and pressure, temperature and conversion distributions in three-dimensional molds with complicated geometries. The validity of the two schemes is evaluated by comparison with analytical solutions of simple geometries. In all instances excellent agreement is observed. Numerical case studies are provided to demonstrate the effectiveness of the developed computer codes. The results show that the numerical procedure based on the nodal partial saturation concept, developed in this study, provides numerically valid and reasonably accurate predictions.