Structural changes induced by Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> addition in strontium-borate glass matrix

Glasses of the xFe₂O₃·(100−x)[B₂O₃·SrO] system, with 0 ≤ x ≤ 30 mol% were studied by X-ray diffraction, density, optical microscopy and FT-IR spectroscopy measurements. The X-ray patterns for the prepared system show that vitreous phase is present only in the sample with x < 40 mol%. For x ≥ 40 mol% in the studied samples is evidenced crystalline phase of Fe₂O₃. SEM measurements for the sample with x = 40 mol% shows that there are formed Fe₂O₃ microcrystallites with 10–20 μm dimension. FT-IR spectroscopy measurements shown that BO₃ and BO₄ are the main structural units of the glass system and the iron ions are located in the glass network.     

Intense blue and violet luminescence in the (B<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript>):Eu<Superscript>2+</Superscript> system

Glassy-crystalline samples of compositions (B₂O₃-Al₂O₃-SiO₂):Eu²⁺ (3 at %) and (B₂O₃-2SiO₂):Eu²⁺ (3 at %) were obtained by sintering the initial powdered mixtures at 1300°C in air. Being excited by laser radiation at a wavelength of 325 nm, the former samples exhibit intense blue photoluminescence with a maximum at 434–448 nm, while the latter samples emit in the violet spectral interval with a maximum at 409 nm. An increase in the content of B₂O₃ leads to a shift of the emission maximum toward a shorter wavelength, while additional annealing at 1300°C C in vacuum shifts the spectrum toward longer wavelengths.     

Effect of Eu<Subscript>2</Subscript>O<Subscript>3</Subscript> doping on the crystallization behavior of BaO-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

We gave studied the crystallization behavior of 30BaO · 25Bi₂O₃ · 45B₂O₃ glasses doped with Eu₂O₃ to different levels. At a Eu₂O₃ content of 7 mol % or higher, the glasses undergo volume crystallization. The only precipitating phase is a solid solution between europium and bismuth oxides. With increasing europium concentration in the glass, the structure of the crystallites changes from cubic to rhombohedral. We have investigated the morphology, physicochemical properties, and luminescence spectra of the glasses and glass-ceramics.     

Thermal Analysis of the Ternary System Li<Subscript>2</Subscript>WO<Subscript>4</Subscript>-WO<Subscript>3</Subscript>-Li<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript>

Thermal analysis results indicate that the liquidus surface of the Li₂WO₄-WO₃-Li₂B₄O₇ system consists of the primary phase fields of Li₂WO₄, Li₂B₄O₇, WO₃, Li₂WO₄ · WO₃ (congruent melting), 3Li₂WO₄ · 2Li₂B₄O₇ (congruent melting), and Li₂WO₄ · 3WO₃ (incongruent melting). Low-melting-point compositions are selected that are potentially attractive for the low-temperature synthesis of lithium tungsten bronze powders.     

Enthalpy of Formation of MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript> · 0.793Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Nonstoichiometric Spinel at 1900 K from High-Temperature Mass Spectrometry Data

The composition and partial pressures of vapor species over the pseudobinary system Al₂O₃–MgO have been determined by high-temperature mass spectrometry. The data obtained have been used to evaluate the standard enthalpy of formation of nonstoichiometric spinel with the composition MgAl₂O₄ · 0.793Al₂O₃ from its constituent oxides by third-law calculations. The entropy of MgAl₂O₄ · 0.793Al₂O₃ has been evaluated using a regular-solution model with allowance for cation inversion.     

Synthesis and microwave absorption property of ternary composites: polyaniline/CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/Ba<Subscript>3</Subscript>Co<Subscript>2</Subscript>Fe<Subscript>24</Subscript>O<Subscript>41</Subscript>

Polyaniline (PANI)/CoFe₂O₄/Ba₃Co₂Fe₂₄O₄₁ composite was prepared by an in-situ polymerization method. The phase structure, morphology and magnetic properties of the as-prepared PANI/CoFe₂O₄/Ba₃Co₂Fe₂₄O₄₁ composite were characterized by XRD, FT-IR, SEM, TEM, and VSM, respectively. The microwave absorption properties of the composite were investigated by using a vector network analyzer in the 2–18 GHz frequency range. The results show that the maximum reflection loss value of the PANI/CoFe₂O₄/Ba₃Co₂Fe₂₄O₄₁ composite reaches ?30.5 dB at 10.5 GHz with a thickness of 3 mm and the bandwidth of reflection loss below ?10 dB reaches up to 1.2 GHz. The excellent microwave absorption properties of the as-prepared PANI/CoFe₂O₄/Ba₃Co₂Fe₂₄O₄₁ composite due to the enhanced impedance match between dielectric loss and magnetic loss.     

Mechanical properties and microstructure of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/mullite composite

An Al₂O₃/5 vol.% mullite composite was synthesized by using reaction sintering of Al₂O₃/0.78 wt.% SiC at 1,600 °C for 2 h in air. The phase analysis of the Al₂O₃/mullite composite was carried out using X-ray diffraction (XRD). There were two kinds of mullite in alumina/mullite composite, namely, 3Al₂O₃·2SiO₂ and Al_5.65Si_0.35O_9.175. The microstructure of the Al₂O₃/mullite composite was investigated using scanning electron microscope (SEM) and transmission electron microscope (TEM). The mechanical properties such as Young’s modulus, Poisson’s ratio, hardness, toughness and strength of the Al₂O₃/mullite composite were investigated. The influence of mullite on the composite is discussed.     

Low-firing Li<Subscript>2</Subscript>ZnTi<Subscript>3</Subscript>O<Subscript>8</Subscript> microwave dielectric ceramics with BaCu(B<Subscript>2</Subscript>O<Subscript>5</Subscript>) additive

Phase purity, microstructure, sinterability and microwave dielectric properties of BaCu(B₂O₅)-added Li₂ZnTi₃O₈ ceramics and their cofireability with Ag electrode were investigated. A small amount of BaCu (B₂O₅) can effectively reduce the sintering temperature from 1075°C to 925°C, and it does not induce much degradation of the microwave dielectric properties. Microwave dielectric properties of ε _r = 23·1, Q × f = 22,732 GHz and τ _f = − 17·6 ppm/°C were obtained for Li₂ZnTi₃O₈ ceramic with 1·5 wt% BaCu(B₂O₅) sintered at 925°C for 4 h. The Li₂ZnTi₃O₈ +BCB ceramics can be compatible with Ag electrode, which makes it a promising microwave dielectric material for low-temperature co-fired ceramic technology application.     

Perovskite M<Superscript>I</Superscript>M<Superscript>II</Superscript>O<Subscript>3</Subscript> as a matrix for incorporation of the actinide fraction of HLW

Perovskites of the compositions xLa₂O₃·Al₂O₃ and xLa₂O₃·Fe₂O₃ were prepared by cold pressing and sintering at temperatures of up to 1500°C, and their properties were studied. Perovskites based on lanthanum aluminate are more porous than those based on lanthanum ferrite, whereas the rate of radionuclide leaching from the former compounds is lower than from the latter compounds. The parameter x varied in a relatively wide range does not affect the leaching rate.     

Effects of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> additive on sintering behavior and microwave dielectric properties of ZnTa<Subscript>2</Subscript>O<Subscript>6</Subscript> ceramics

ZnTa₂O₆ ceramics with various amount of Al₂O₃ additive were synthesized by a conventional mixed-oxide route. The grain growth of ZnTa₂O₆ ceramics was accelerated with Al₂O₃ additive. However, excessive addition (>1.0 wt%) of Al₂O₃ leaded to abnormal grain growth. With Al₂O₃ addition, the Al₂O₃ additive did not solubilized into ZnTa₂O₆ structure but resulted in forming the second phase. The Al₂O₃ addition resulted in the lower sintering temperature of ZnTa₂O₆ ceramics and improved microwave dielectric properties. The dielectric constant (ε_r) of the samples did not change much and ranged from 32.41 to 34.33 with different amount of Al₂O₃ addition. The optimized quality factor (Q × f) was higher than 70,000 GHz as a result of the denser ceramics. The temperature coefficient of resonant frequency (τ _f ) of the doped ZnTa₂O₆ ceramics could be optimized to near-zero.     

Low-temperature sintering behavior and properties of <Emphasis Type="Italic">monoclinic</Emphasis>-SrAl<Subscript>2</Subscript>Si<Subscript>2</Subscript>O<Subscript>8</Subscript> ceramics prepared via an aqueous suspension milling process

In this work, by an aqueous suspension milling process, boric acid (H₃BO₃), calcium hydroxide [Ca(OH)₂], strontium carbonate (SrCO₃) and barium hydroxide octahydrate [Ba (OH)₂·8H₂O] are mixed with strontium carbonate (SrCO₃) and kaolin (Al₂O₃·2SiO₂·2H₂O) to prepare SrAl₂Si₂O₈ ceramics with a sintering temperature of 950 °C. According to chemical compositions of flux agents B₂O₃, CaO·2B₂O₃, SrO·2B₂O₃ and BaO·2B₂O₃, raw materials boric acid, calcium hydroxide, strontium carbonate and barium hydroxide octahydrate were introduced to the suspension slurries of strontium carbonate and kaolin to decrease the densification sintering temperature of SrAl₂Si₂O₈ ceramics. In addition, the Sr element in SrAl₂Si₂O₈ ceramics are partly substituted with Ba and Ca elements, respectively, to investigate the low-temperature sintering behavior of partly substituted SrAl₂Si₂O₈ ceramics. The results indicated that the addition of flux agents to SrAl₂Si₂O₈ ceramics can availably achieve the densification sintering of SrAl₂Si₂O₈ ceramics at 950 °C, whereas the substitution of Sr with Ca or Ba have a great effect on sintering behaviors and dielectric properties of SrAl₂Si₂O₈ ceramics. Additionally, main crystal phases of the SrAl₂Si₂O₈ ceramics are monoclinic- SrAl₂Si₂O₈ and small quartz, but the evolution of crystal phases also depend on flux agents.     

Thermodynamic properties of Dy<Subscript>2</Subscript>O<Subscript>3</Subscript> · 2ZrO<Subscript>2</Subscript> and Ho<Subscript>2</Subscript>O<Subscript>3</Subscript> · 2ZrO<Subscript>2</Subscript> in the range 10–340 K

The low-temperature heat capacity of Dy₂O₃ · 2ZrO₂ and Ho₂O₃ · 2ZrO₂ has been determined by adiabatic calorimetry in the temperature range 10–340 K. The results have been used to calculate the entropy, enthalpy increment, and reduced Gibbs energy of the zirconates without taking into account their low-temperature magnetic transformations.     

Effect of Y<Subscript>2</Subscript>O<Subscript>3</Subscript> on the crystallization behavior of SiO<Subscript>2</Subscript>–MgO–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

A series of glass comprising of SiO₂–MgO–B₂O₃–Y₂O₃–Al₂O₃ in different mole ratio has been synthesized. The crystallization kinetics of these glasses was investigated using various characterization techniques such as differential thermal analysis (DTA), thermo gravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM). Crystallization behavior of these glasses was markedly influenced by the addition of Y₂O₃ instead of Al₂O₃. Addition of Y₂O₃ increases the transition temperature, T _g, crystallization temperature, T _c and stability of the glasses. Also, it suppresses the formation of cordierite phase, which is very prominent and detrimental in MgO-based glasses. The results are discussed on the basis of the structural and chemical role of Y³⁺ and Al³⁺ ions in the present glasses.     

Phase equilibria in the K<Subscript>2</Subscript>O-MgO-B<Subscript>2</Subscript>O<Subscript>3</Subscript> system

Subsolidus (500–700°C) phase relations in the K₂O-MgO-B₂O₃ system have been studied by X-ray diffraction. The results are used to construct the phase compatibility diagram of the K₂O-MgO-B₂O₃ system in the range 650–700°C. A new ternary compound of composition K₂Mg₃B₂O₇, with the constituent oxides in the molar ratio 1: 3: 1, is identified.     

Hollow biomorphic Al<Subscript>2</Subscript>O<Subscript>3</Subscript> fibers produced from sisal

Al₂O₃ fibers with a hollow morphology were produced by Al-vapor infiltration-reaction and subsequent oxidation from pyrolysed fibers of natural sisal. Following pyrolysis, the bio-fiber template was reacted with gaseous Al at 1,400 °C–1,600 °C in vacuum to form Al₄C₃. After an oxidation/sintering process at 1,550 °C, the biomorphic Al₄C₃ fibers were fully converted into Al₂O₃, maintaining the microstructural features of the native sisal. Phase and microstructural characterization during processing were evaluated by high temperature X-ray diffractometry and scanning electron microscopy, respectively. Thermo-analyses were performed in the Al₄C₃ samples in order to estimate the reactions and the weight change during the oxidation step.     

Cr<Superscript>3+</Superscript> activated Zn<Subscript>3</Subscript>Al<Subscript>2</Subscript>Ge<Subscript>3</Subscript>O<Subscript>12</Subscript>: a novel near-infrared long persistent phosphor

The near-infrared (NIR) long persistent phosphors have gained considerable attention owing to the potential applications in in vivo imaging. A novel NIR long-persistent phosphors Zn₃Al₂Ge₃O₁₂:Cr³⁺ was successfully synthesized by a high temperature solid-state reaction. The luminescent properties and the afterglow behaviors of the Zn₃Al₂Ge₃O₁₂:Cr³⁺ were investigated in detail. On the basis of thermoluminescence analyses, the mechanism of the persistent afterglow of the phosphors was also discussed briefly. The afterglow duration of this phosphor can last more than 12 h with the 650–750 nm emission range after stoppage of 254 nm ultraviolet light irradiation. Specifically, the persistent luminescence intensity and duration were regulated by changing Cr³⁺ doping concentration. All the results indicate that the Cr³⁺ activated Zn₃Al₂Ge₃O₁₂ has promising potential of practical applications.     

Preparation and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/Ag composite magnetic nanoparticles

Fe₃O₄ magnetic nanoparticles being used as seeding materials, Ag⁺ ions on the Fe₃O₄ magnetic nanoparticles reduced to the metal form by tartaric acid using heated treatment. Thus, Fe₃O₄/Ag composite core-shell magnetic nanoparticles were synthesized. The products were characterized by transmission electron microscope (TEM) and x-ray diffraction (XRD). Both TEM and XRD results showed that the Ag nanoparticles were well distributed on the surface of Fe₃O₄ magnetic nanoparticles. The size for Fe₃O₄/Ag composite magnetic nanoparticles which were spherical shape was ≃40 nm. Furthermore, the magnetic properties of samples were characterized on a vibrating sample magnetometer. Under optimal conditions, Fe₃O₄/Ag composite nanoparticles showed higher magnetism than pure Fe₃O₄ nanoparticles. The text was submitted by the authors in English.     

Phase developments in Pb(Mg<Subscript>1/2</Subscript>W<Subscript>1/2</Subscript>)O<Subscript>3</Subscript> and Pb(Zn<Subscript>1/2</Subscript>W<Subscript>1/2</Subscript>)O<Subscript>3</Subscript> via B-site precursor route

Phase formation stages of MgWO₄ and ZnWO₄ (precursor compositions for following steps) were investigated by monitoring the reactions of oxide chemicals at various temperatures. Developed phases were examined by using X-ray diffraction (XRD). Successive attempts were also conducted for Pb(Mg_1/2W_1/2)O₃ (PMW) and Pb(Zn_1/2W_1/2)O₃ (PZW) by reacting PbO with the precursor compounds. Stages of phase development in the two compositions were also analyzed. The results are compared with those of another tungsten-containing perovskite Pb(Fe_2/3W_1/3)O₃ (PFW) and its B-site precursor Fe₂WO₆. After PbO addition to the precursor powders, a perovskite phase formed directly (i.e., without any intermediate phases) in the case of PMW. For PbO + ½ZnWO₄, in contrast, the decomposition of ZnWO₄ and preferential reaction with PbO resulted in Pb₂WO₅ and ZnO, instead of the perovskite PZW.     

Calcium bismuth borates in the CaO-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The 600°C (subsolidus) section of the CaO-Bi₂O₃-B₂O₃ phase diagram has been studied by x-ray diffraction and differential thermal analysis. A new calcium bismuth borate of composition CaBi₂B₄O₁₀ has been identified, and the existence of CaBi₂B₂O₇ has been confirmed. According to T-x phase diagram data, these compounds form peritectically at 700±5 and 783±5°C, respectively.     

Temperature-stable and low loss Fe-containing dielectrics in BaO-Ln<Subscript>2</Subscript>O<Subscript>3</Subscript>-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-Ta<Subscript>2</Subscript>O<Subscript>5</Subscript> system

Polycrystalline samples of Ba₄Ln₂Fe₂Ta₈O₃₀ (Ln = La and Nd) were prepared by a high temperature solid-state reaction technique. The formation, structure, dielectric and ferroelectric properties of the compounds were studied. Both compounds are found to be paraelectrics with filled tetragonal tungsten bronze (TB) structure at room temperature. Dielectric measurements revealed that the present ceramics have exceptional temperature stability, a relatively small temperature coefficient of dielectric constant (τ _ε ) of −25 and −58 ppm/°C, with a high dielectric constant of 118 and 96 together with a low dielectric loss of 1.2 × 10⁻³ and 2.8 × 10⁻³ (at 1 MHz) for Ba₄La₂Fe₂Ta₈O₃₀ and Ba₄Nd₂Fe₂Ta₈O₃₀, respectively. The measured dielectric properties indicate that both materials are possible candidates for the fabrication of discrete multilayer capacitors in microelectronic technology.