增塑剂对聚乳酸性能影响的研究

采用熔融共混法,以丙三醇、乙酰柠檬酸三正丁酯(ATBC)以及邻苯二甲酸二辛酯(DOP)作为增塑剂,对聚乳酸(PLA)进行增塑改性,讨论了不同的增塑剂及含量对改性PLA性能的影响.结果表明,3种增塑剂均能提高PLA的韧性,其中利用ATBC增塑改性时效果最好,且当其含量为15～20 份时,改性PLA的力学性能较佳;随着ATBC的含量增加,PLA的熔体流动性进一步增强,熔点(Tm)、玻璃化转变温度(Tg)以及结晶温度均有所下降,PLA的结晶能力增强,维卡热变形温度呈先下降后上升的趋势,改性PLA的吸水率有所降低,降解率有所上升.     

聚乙二醇对聚乳酸的共聚改性研究

以乳酸单体(LA)为原料,锌酸亚锡[Sn(Oct)2]为催化剂,按m[Sn(Oct)2]∶m(LA)=0.008∶1投料,在170℃、0.095 MPa下反应8 h,直接熔融缩聚合成PLA,其Mη(黏均摩尔质量)为12514.将PLA与PEG-400、PEG-600和PEG-800按m(PLA)∶m(PEG)=9∶1共聚合成系列PLEGs.用特性黏度、FT-IR、DSC、接触角测定等测试手段对其进行表征.结果表明:在系列PLEGs中,PEG-600和PLA共聚合成的PLEG的最高,可达28900.PEG-800和PLA共聚合成的PLEG接触角最小,为57.0°,表明其亲水性能最好.     

聚乙二醇增塑聚乳酸的非等温结晶动力学研究

采用DSC方法对聚乙二醇(PEG)增塑聚乳酸的非等温结晶动力学进行了研究。结果表明,PEG的加入明显提高了聚乳酸的结晶速度。对所得数据分别用Ozawa方程和莫志深方法进行了处理,发现在给定温度范围里非等温结晶时,PLA/PEG主要是以均相成核的三维生长方式结晶;PLA的结晶速度随着PEG分子质量的增加而升高。     

聚乙二醇增塑聚乳酸的等温结晶动力学研究

采用DSC方法对聚乙二醇(PEG)增塑聚乳酸的等温结晶动力学进行了研究。结果表明,PEG的加入提高了聚乳酸的结晶速度,在相同结晶温度下,随着PEG摩尔质量的增大,结晶速率增大,结晶活化能先减小后增大。不同摩尔质量PEG增塑PLA的结晶成核机理和生长方式一样。     

聚乙二醇对直接合成聚乳酸-聚乙二醇的影响

为了得到综合性能较佳的生物降解材料聚乳酸-聚乙二醇(PLEG),以SnO为催化剂．直接以外消旋乳酸单体为原料,与不同数均分子量(Mn)的聚乙二醇(PEG)共聚合,通过直接熔融共聚法,在165℃、70Pa下．反应15h,合成了系列PLUG。用特性黏数测试、傅里叶变换红外光谱、核磁共振氢谱、差示扫描量热法、X射线衍射、接触角测试等手段对其进行表征,发现PEG的Mn为1000时,特性黏数最大,为0．4009dL/g,且亲水性得到改善。     

聚乳酸纤维及其应用

简单介绍了聚乳酸的聚合方法和目前聚合工艺方面的新发展。介绍了聚乳酸纤维的纺丝方法、聚乳酸熔融纺丝工艺流程及目前国内外聚乳酸纤维的生产、开发情况。比较了聚乳酸纤维与涤纶等合成纤维及真丝等天然纤维的物理性能指标。最后,介绍了聚乳酸纤维在医药、织物和非织造布方面的应用。     

熔纺聚乳酸纤维的结构与性能研究

通过熔融纺丝法制备了生物可降解左旋聚乳酸(PLLA)纤维,对纤维进行了拉伸和热定型等后处理,用电子单纤维强力仪和X-射线衍射仪研究了PLLA纤维的力学性能和结晶性能,讨论了纺丝温度、拉伸倍数、定型时间和定型温度等对纤维力学性能的影响。结果表明,当纺丝温度为200℃时,纤维可纺性最好。当拉伸倍数为4倍,热定型温度为60℃,定型时间为30min时,PLLA纤维具有最佳的力学性能,其晶区具有α晶型结构。     

高性能聚乳酸纤维的研究进展

介绍了高强度、可控降解周期的聚乳酸及其共聚物、共混物纤维的成型方法和纤维的应用情况;阐述了熔融纺丝、溶液纺丝、静电纺丝、超临界流体法、凝胶冻干等纤维成型方法的特点;评价了成型工艺对纤维形态结构和性能的影响、研究聚乳酸纤维的新方法、新成果以及高性能聚乳酸纤维在生物医学领域、日用工业等领域的应用前景。     

聚乙二醇对聚乳酸/热塑性淀粉复合材料性能的影响

采用注塑法制备了聚乙二醇(PEG)改性的聚乳酸(PLA)/热塑性淀粉(TPS)复合材料,研究了PEG对PLA/TPS复合材料的加工流变性能、力学性能的影响,采用差示扫描量热(DSC)仪和扫描电子显微镜(SEM)进行微观结构分析并研究了加工工艺对复合材料性能的影响.结果表明,当PEG的质量分数为3%时,复合材料的力学性能最佳;DSC测试和SEM分析表明,PEG的加入提高了复合材料的塑性, 改善了其相容性.     

不同PEG含量对PLA/PEG共混物结晶动力学的影响

采用溶液共混法制备了一系列不同配比的聚乳酸(PLA)/聚乙二醇(PEG)共混物。通过偏光显微镜(POM)、扫描电镜(SEM)和差式扫描量热仪(DSC)研究了不同PEG含量的PLA/PEG共混物在不同结晶温度下,聚乳酸的晶体形貌、球晶生长速率及热力学性能。研究发现,PEG能够显著提高聚乳酸球晶的生长速率。当PEG含量为60%时,PLA/PEG共混物中聚乳酸球晶的生长速率最快,达到23.6μm/min,比纯聚乳酸的最快球晶生长速率(0.5μm/min)高47倍。但是,当PEG含量高于60%时,聚乳酸球晶的生长速率有所降低。同时,PLA/PEG共混物中聚乳酸球晶速率随结晶温度变化的取向,均向低温移动。另外,PLA/PEG共混物中聚乳酸球晶呈现环状花纹。DSC测试结果表明,随着PEG含量的增加,PLA/PEG共混物的玻璃化转变温度明显降低。     

Properties of Poly(vinyl chloride)/poly(ethylene oxide)/polyaniline Conductive Films: The Effect of Poly(ethylene glycol) Diglycidyl Ether

The effect of polyaniline and poly(ethylene glycol) diglycidyl ether on tensile properties, morphology, thermal degradation, and electrical conductivity of poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films was studied. The poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films were prepared using a solution casting technique at room temperature until a homogeneous solution was produced. Poly(vinyl chloride)/poly(ethylene oxide)/polyaniline/poly(ethylene glycol) diglycidyl ether conductive films exhibit higher electrical properties, tensile strength, modulus of elasticity but lower final decomposition temperature than poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films. Scanning electron microscopy morphology showed that the polyaniline more widely dispersed in the poly(vinyl chloride)/poly(ethylene oxide) blends with the addition of poly(ethylene glycol) diglycidyl ether as surface modifier.     

聚乙二醇中咪唑与芳基硼酸的N-芳基化反应

N-芳基咪唑类化合物是一类非常重要的结构单元,常见于药物、农药以及生物分子中,因此寻找新的合成N-芳基咪唑类物质的方法成为有机合成化学家关注的热点问题之一。在绿色化学的倡导下,研究发展了一个促进咪唑类底物与芳基硼酸N-芳基化反应的催化体系,它是以Cu_2O(10%)为催化剂,以聚乙二醇400为反应介质,在室温下反应。研究结果表明,该催化体系适用于咪唑类底物与各种具有不同取代基的芳基硼酸的N-芳基化反应,为N-芳基咪唑类化合物提供一个简单、有效、绿色的合成方法。     

Effects of pH and Neutral Salts on the Adsorption of the Poly(ethylene glycol terephthalate) Condensates Toward Poly(ethylene terephthalate) Fiber

This study deals with the effects of pH and neutral salts on the adsorption of PET fiber with four kinds of poly(ethylene glycol terephthalate) condensated from dimethyl terephthalate (DMT) and poly(ethylene glycol) (PEG). The surface properties of the aqueous solution, the contact angle of polyol‐treated PET fabrics, and its parameters were also discussed. The pH of the solution or the adding of neutral salt in the polyol solution largely affected the contact angle of polyol‐treated PET fabrics as well as the surface tension of the solution. A lower pH of the polyol solution or adding neutral salts in the solution showed a lower surface tension and a lower contact angle that resulted in a better adsorption between polyol and poly(ethylene terephthalate) fibers. The lower pH of the solutions and a higher valence of the added neutral salt in the solution showed a largely positive effect on the adsorption parameters, and the order of effectiveness is Al₂(SO₄)₃ > MgSO₄ > Na₂SO₄.     

聚乳酸/聚乙二醇共混物的结晶与降解行为

针对聚乳酸（PLLA）亲水性差、降解周期长的问题,利用与亲水性高分子聚乙二醇（PEG）共混的方法对其进行改性。采用转矩流变仪制备了不同组成的PLLA/PEG共混物颗粒,系统研究了PLLA/PEG共混物的结晶和熔融、亲水性和在酸碱介质中的降解行为。结果表明,PEG的加入增强了共混物中PLLA的结晶能力,提高了PLLA在降温过程中的熔融结晶温度。PLLA/PEG共混物在等温结晶中表现出比纯PLLA更快的结晶速度。通过改变PLLA/PEG共混物的组成,可调控材料的表面亲水性和降解速率。随着PEG含量的增多,PLLA/PEG共混物的表面接触角降低。PLLA与PLLA/PEG共混物均可在水溶液中降解,共混物的降解速率高于纯PLLA,随着PEG含量的升高和降解液中酸碱浓度的提高,PLLA/PEG共混物的降解速率加快。     

Poly(ethylene glycol) electrolyte gels prepared by condensation reaction

Poly(ethylene glycol) electrolyte gels were prepared by condensation reaction in the presence of tetraethoxysilane. Differential scanning calorimetry and X‐ray diffraction spectroscopy were used to investigate the thermal transition behavior and crystalline structure of polymer gels prepared. Both formation of crosslinks and incorporation of salts or plasticizers reduced the development of crystalline structure of poly(ethylene glycol)s. Cyclic voltammetric and ion‐conducting behaviors of polymer gels were analyzed using potentiostat and impedance spectroscopy, and those were also considerably affected by the crosslinking density of polymers and the concentration of electrolyte salt or plasticizers incorporated. Poly(ethylene glycol) gels possessing certain levels of electrolyte salt and plasticizer were expected to have applications of solid electrolytes for lithium polymer secondary batteries. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 948–956, 2002     

Synthesis and Surface Properties of Poly(methyl methacrylate)/Poly(ethylene glycol) Binary Brushes

A new kind of binary polymer brushes was synthesized from two immiscible polymers, PMMA and PEG, on GPS‐modified silicon wafers. Surface composition, layer thickness, coverage, chain density, wetting ability, morphology and protein adsorption of the binary brushes were investigated by XPS, ellipsometry, AFM and contact angle measurements. The results show that both PMMA and PEG were successfully grafted onto the surface. The surface coverage and the chain density of PMMA and PEG brushes can be controlled by modulating the reaction temperature and time. This kind of binary polymer brushes exhibits a distinct microphase‐separated structure and excellent protein‐preventing property.

     

聚乙二醇中共轭烯炔化合物的合成

发展了一种在聚乙二醇介质中末端炔烃与缺电子炔烃选择性生成共轭烯炔化合物的方法。在三苯基膦氯化钯(2mol%)、溴化亚铜(4mol%)、PEG-400(1.0g)和氮气的作用下,1mmol末端炔烃与0.5mmol缺电子炔烃可以顺利地发生交叉偶联反应选择性生成相应的共轭烯炔化合物,该反应产率较高,对环境友好,且催化体系可以适当地重复使用。     

Biodegradable polymer blends of poly(lactic acid) and poly(ethylene glycol)

Poly(lactic acid) (PLA) and poly(ethylene glycol) (PEG) were melt-blended and extruded into films in the PLA/PEG ratios of 100/0, 90/10, 70/30, 50/50, and 30/70. It was concluded from the differential scanning calorimetry and dynamic mechanical analysis results that PLA/PEG blends range from miscible to partially miscible, depending on the concentration. Below 50% PEG content the PEG plasticized the PLA, yielding higher elongations and lower modulus values. Above 50% PEG content the blend morphology was driven by the increasing crystallinity of PEG, resulting in an increase in modulus and a corresponding decrease in elongation at break. The tensile strength was found to decrease in a linear fashion with increasing PEG content. Results obtained from enzymatic degradation show that the weight loss for all of the blends was significantly greater than that for the pure PLA. When the PEG content was 30% or lower, weight loss was found to be primarily due to enzymatic degradation of the PLA. Above 30% PEG content, the weight loss was found to be mainly due to the dissolution of PEG. During hydrolytic degradation, for PLA/PEG blends up to 30% PEG, weight loss occurs as a combination of degradation of PLA and dissolution of PEG. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1495–1505, 1997