Application of diamond microelectrodes for end-column electrochemical detection in capillary electrophoresis

Highly boron-doped diamond microelectrodes were employed in an end-column electrochemical detector for capillary electrophoresis (CE). The diamond microline electrodes were fabricated from conducting diamond thin films (exposed surface area, 300 x 50 microm), and their analytical performance as CE detectors was evaluated in a laboratory-made CE installation. The CE-ED system exhibited high separation efficiency for the detection of several catecholamines, including dopamine (DA), norepinephrine (NE), and epinephrine (E), with excellent analytical performance, for example, 155,000 theoretical plates for DA. The diamond-based electrochemical detection system also displayed low detection limits (approximately 20 nM for E at S/N = 3) and a highly reproducible current response with 10 repetitive injections of mixed analytes containing DA, NE, and E (each 50 microM), with relative standard deviations (RSD) of approximately 5%. The performance of the diamond detector in CE was also evaluated in the detection of chlorinated phenols (CP). When compared to the carbon fiber microelectrode, the diamond electrode exhibited lower detection limits in an end-column CE detection resulting from very low noise levels and highly reproducible analyses without electrode polishing due to analyte fouling, which makes it possible to perform easier and more stable CE analysis.     

Microchip capillary electrophoresis with electrochemical detection

A novel microchip capillary electrophoresis system with electrochemical detection, using the replaceable microelectrode, is first reported. This kind of electrode can be fabricated in general laboratories and can be replaced quickly with electrodes of different materials according to the requirements of experiments. The end-column electrochemical detection on microchip CE was achieved by fixing the working electrode (such as carbon fiber, Pt, or Au, etc.) through a guide tube on the end of the separation channel. The experiment results indicate that the alignment of the electrode with the channel outlet can be carried out accurately and reproducibly, and therefore, the detection device has low noise and good reproducibility. The detection limit of dopamine is 2.4 x 10(-7) M, which is the lowest result reported so far. The separation and detection of dopamine, 5-hydroxytryptamine and epinephrine using carbon fiber and Pt microdisk electrodes within 50 s was successfully performed.     

Rudimentary capillary-electrode alignment for capillary electrophoresis with electrochemical detection

A capillary-electrode holder was constructed for electrochemical detection in capillary electrophoresis (CE). The device allows for positioning of the working electrode at the end of the capillary column without the aid of micropositioners or microscopes. The design facilitates the exchange of electrodes and capillaries without the need of refabricating the entire capillary-electrode setup. The system can be assembled in a very short period of time. Alignment with the self-guided system proved to be reproducible for the electrodes used (carbon, nickel, copper). The advantages of reduced downtime and low cost, make the device very attractive for the routine analysis of electroactive species by CE with electrochemical detection.     

On-column electrochemical detection for microchip capillary electrophoresis

The development of a cellulose acetate decoupler for on-column electrochemical detection in microchip capillary electrophoresis is presented. The capillary based laser-etched decoupler is translated to the planar format to isolate the detector circuit from the separation circuit. The decoupler is constructed by aligning a series of 20 30-microm holes through the coverplate of the microchip with the separation channel and casting a thin film of cellulose acetate within the holes. The decoupler shows excellent isolation of the detection circuit for separation currents up to 60 microA, with noise levels at or below 1 pA at a carbon fiber electrode. Detection limits of 25 nM were achieved for dopamine. This decoupler design combines excellent mechanical stability, effective shunting of high separation currents, and ease of manufacture.     

Boron-doped diamond microelectrodes for use in capillary electrophoresis with electrochemical detection

The fabrication and characterization of boron-doped diamond microelectrodes for use in electrochemical detection coupled with capillary electrophoresis (CE-EC) is discussed. The microelectrodes were prepared by coating thin films of polycrystalline diamond on electrochemically sharpened platinum wires (76-, 25-, and 10-microm diameter), using microwave-assisted chemical vapor deposition (CVD). The diamond-coated wires were attached to copper wires (current collectors), and several methods were explored to insulate the cylindrical portion of the electrode: nail polish, epoxy, polyimide, and polypropylene coatings. The microelectrodes were characterized by scanning electron microscopy, Raman spectroscopy, and cyclic voltammetry. They exhibited low and stable background currents and sigmoidally shaped voltammetric curves for Ru(NH3)6(3+/2+) and Fe(CN)6(3-/4-) at low scan rates. The microelectrodes formed with the large diameter Pt and sealed in polypropylene pipet tips were employed for end-column detection in CE. Evaluation of the CE-EC system and the electrode performance were accomplished using a 10 mM phosphate buffer, pH 6.0, run buffer, and a 30-cm-long fused-silica capillary (75-microm i.d.) with dopamine, catechol, and ascorbic acid serving as test analytes. The background current (approximately 100 pA) and noise (approximately 3 pA) were measured at different detection potentials and found to be very stable with time. Reproducible separation (elution time) and detection (peak current or area) of dopamine, catechol, and ascorbic acid were observed with response precisions of 4.1% or less. Calibration curves constructed from the peak area were linear over 4 orders of magnitude, up to a concentration between 0.1 and 1 mM. Mass limits of detection for dopamine and catechol were 1.7 and 2.6 fmol, respectively (S/N = 3). The separation efficiency was approximately 33,000, 56,000, and 98,000 plates/m for dopamine, catechol, and ascorbic acid, respectively. In addition, the separation and detection of 1- and 2-naphthol in 160 mM borate buffer, pH 9.2, was investigated. Separation of these two analytes was achieved with efficiencies of 118,000 and 126,000 plates/m, respectively.     

Carbon film-based interdigitated array microelectrode used in capillary electrophoresis with electrochemical detection

A carbon film based interdigitated ring-shaped array (IDRA) microelectrode was applied to capillary electrophoresis with electrochemical detection to enhance the detection sensitivity on the basis of the redox cycling of electrochemical reversible species at the IDRA microelectrode. We propose a simple capillary-electrode connection device that consists of an X-Y-Z fiber aligner, an electrochemical cell, and a Nafion tubing joint that will enable the detection capillary to be aligned easily on the IDRA microelectrode and isolate the separation voltage from the electrochemical detection system. We used the off-column amperometric detection of aqueous ferrocene and catecholamines by capillary electrophoresis with an IDRA microelectrode to investigate the effects of the capillary-to-electrode distance and the separation voltage on the response currents in single and dual modes and the collection efficiencies (CE) and redox cycles (Rc) at the IDRA microelectrode. The results show that CE and Rc increase when we increase the distance and lower the separation voltage. The limiting currents also increase as the separation voltage decreases in the dual mode. Under optimum conditions, the CE and Rc of catechol, with good reversibility, reach 83.9% and 3.67, respectively. Our results showed that dual-mode detection with the IDRA microelectrode was capable of achieving lower detection limits than single-mode detection.     

Separation of serotonin from catechols by capillary zone electrophoresis with electrochemical detection

Capillary zone electrophoresis with electrochemical detection is demonstrated with columns having only 9-microns inner diameter. Amperometric detection limits of 0.7 amol are reported for serotonin. The difficult problem of resolving serotonin and dopamine--two neurotransmitters of interest having similar electrophoretic mobilities--is addressed by chemical means to improve selectivity. These include buffer modification with 2-propanol and a system employing borate complexation of the catechol in combination with sodium dodecyl sulfate micelles.     

Adsorption-based electrochemical detection of nonelectrochemically active analytes for capillary electrophoresis

A sensitive electrochemical detection method (ECD) for capillary electrophoresis has been developed that is applicable to a much wider range of analytes than more conventional ECD methods. Using a modified Osteryoung square-wave voltammetry method, the adsorption of what are normally considered nonelectrochemically active analytes onto a platinum electrode was found to produce a concentration-proportional response. Although the mechanisms that cause this response may be complex, it appears that it is due to changes in the electrode/solution interface that accompany adsorption of the analyte onto the electrode rather than a simple redox process. Analytes that possess pi-electron density appeared to chemisorb rather than only physically adsorb onto the electrode and gave the best response with detection limits of < 10(-8) M while maintaining good linearity. Because this detection method requires only that the analyte adsorb onto the electrode, it has the advantage of much wider applicability than previously reported electrochemical detection methods. The applicability of this detection method was investigated for a variety of analytes and background electrolyte conditions (varied pH, ionic strength, buffer additives). Comparisons of the sensitivity of this method to UV detection showed that, even for analytes that have good UV chromophores, sensitivities greater than 1 order of magnitude were obtained using adsorption-based electrochemical detection.     

Cellulose acetate decoupler for on-column electrochemical detection in capillary electrophoresis.

A new decoupler for on-column electrochemical detection in capillary electrophoresis is presented. The decoupler is constructed by etching a series of holes through the side of the separation capillary with a CO2 laser and then coating the holes with cellulose acetate. The decoupler shows isolation of the detection circuit for separation currents up to 30 microA. Detection limits below 1 nM were achieved for four model compounds, including anions, neutrals, and cations, using the laser-etched decoupler. This decoupler design combines excellent mechanical stability, effective shunting of high separation currents, and ease of manufacture.     

Microchip capillary electrophoresis with electrochemical detection of thiol-containing degradation products of V-type nerve agents

A microchip protocol for the capillary electrophoresis separation and electrochemical detection of thiol-containing degradation products of V-type nerve agents is described. The microchip assay relies on the derivatization reaction of 2-(dimethylamino)ethanethiol (DMAET), 2-(diethylamino)ethanethiol (DEAET), and 2-mercaptoethanol (ME) with o-phthaldialdehyde in the presence of the amino acid valine along with amperometric monitoring of the isoindole derivatives. Both off-chip and on-chip derivatization reactions have led to highly sensitive and rapid detection of the thiol degradation products. Various parameters influencing the derivatization, separation, and detection processes were examined and optimized. These include the amino acid co-reagent, reagent-mixing ratio, reaction time, injection time, separation voltage, and detection potential. The chip microsystem offers a rapid (<4 min) simultaneous detection of micromolar concentrations of DMAET, DEAET, and ME. Linear calibration plots were observed for the V-type nerve agent thiol degradation products, along with good stability and reproducibility (RSD < 8.0%). Detection limits of 5 and 8 microM were obtained for the off-chip reaction of DMAET and DEAET, respectively, following a 2-s injection. The suitability for assays of environmental matrixes was demonstrated for the determination of DMAET and DEAET in untreated tap and river water samples. The favorable analytical performance makes the new microfluidic device attractive for addressing the needs of various security scenarios.     

Fully integrated on-chip electrochemical detection for capillary electrophoresis in a microfabricated device

Microfabricated lab-on-a-chip devices employing a fully integrated electrochemical (EC) detection system have been developed and evaluated. Both capillary electrophoresis (CE) channels and all CE/EC electrodes were incorporated directly onto glass substrates via traditional microfabrication techniques, including photolithographic patterning, wet chemical etching, DC sputtering, and thermal wafer bonding. Unlike analogous CE/EC devices previously reported, no external electrodes were required, and critical electrode characteristics, including size, shape, and placement on the microchip, were established absolutely by the photolithography process. For the model analytes dopamine and catechol, detection limits in the 4-5 microM range (approximately 200 amol injected) were obtained with the Pt EC electrodes employed here, and devices gave stable analytical performance over months of usage.     

Dual-electrode electrochemical detection for poly(dimethylsiloxane)-fabricated capillary electrophoresis microchips

The development of a poly(dimethylsiloxane)-based (PDMS-based) microchip electrophoresis system employing dual-electrode electrochemical detection is described. This is the first report of dual-electrode electrochemical detection in a microchip format and of electrochemical detection on chips fabricated from PDMS. The device described in this paper consists of a top layer of PDMS containing the separation and injection channels and a bottom glass layer onto which gold detection electrodes have been deposited. The two layers form a tight reversible seal, eliminating the need for high-temperature bonding, which can be detrimental to electrode stability. The channels can also be temporarily removed for cleaning, significantly extending the lifetime of the chip. The performance of the chip was evaluated using catechol as a test compound. The response was linear from 10 to 500 microM with an LOD (S/N = 3) of 4 microM and a sensitivity of 45.9 pA/microM. Collection efficiencies for catechol ranged from 28.7 to 25.9% at field strengths between 200 and 400 V/cm. Dual-electrode detection in the series configuration was shown to be useful for the selective monitoring of species undergoing chemically reversible redox reactions and for peak identification in the electropherogram of an unresolved mixture.     

Portable high-voltage power supply and electrochemical detection circuits for microchip capillary electrophoresis

Miniaturized, battery-powered, high-voltage power supply, electrochemical (EC) detection, and interface circuits designed for microchip capillary electrophoresis (CE) are described. The dual source CE power supply provides +/- 1 kVDC at 380 microA and can operate continuously for 15 h without recharging. The amperometric EC detection circuit provides electrode potentials of +/-2 VDC and gains of 1, 10, and 100 nA/V. The CE power supply power is connected to the microchip through an interface circuit consisting of two miniature relays, diodes, and resistors. The microchip has equal length buffer and separation channels. This geometry allows the microchip to be controlled from only two reservoirs using fixed dc sources while providing a consistent and stable sample injection volume. The interface circuit also maintains the detection reservoir at ground potential and allows channel currents to be measured likewise. Data are recorded, and the circuits are controlled by a National Instruments signal interface card and software installed in a notebook computer. The combined size (4 in. x 6 in. x 1 in.) and weight (0.35 kg) of the circuits make them ideal for lab-on-a-chip applications. The circuits were tested electrically, by performing separations of dopamine and catechol EC and by laser-induced fluorescence visualization.     

In-channel electrochemical detection for microchip capillary electrophoresis using an electrically isolated potentiostat

A new electrode configuration for microchip capillary electrophoresis (CE) with electrochemical (EC) detection is described. This approach makes it possible to place the working electrode directly in the separation channel. The "in-channel" EC detection was accomplished without the use of a decoupler through the utilization of a specially designed, electrically isolated potentiostat. The effect of the working electrode position on the separation performance (in terms of plate height and peak skew) of poly(dimethylsiloxane)-based microchip CEEC devices was evaluated by comparing the more commonly used end-channel configuration with this new in-channel approach. Using catechol as the test analyte, it was found that in-channel EC detection decreased the total plate height by a factor of 4.6 and lowered the peak skew by a factor of 1.3. A similar trend was observed for the small, inorganic ion nitrite. Furthermore, a fluorescent and electrochemically active amino acid derivative was used to directly compare the separation performance of in-channel EC detection to that of a widely used laser-induced fluorescence (LIF) detection scheme. In this case, it was found that the plate height and peak skew for both detection schemes were essentially equal, and the separation performance of in-channel EC detection is comparable to LIF detection.     

Integrated on-capillary electrochemical detector for capillary electrophoresis

An on-capillary electrochemical detector for capillary electrophoresis is described. It consists of a gold wire mounted permanently at the end of the capillary perpendicular to the direction of flow. This mode of detection eliminates the need for the micromanipulators or specially machined cell holders for alignment that are used for in-capillary detection modes. It also makes it possible to perform relatively fast CEEC separations using very short capillaries. The use of this detector for both off-column detection of catecholamines and end-column detection of carbohydrates by CE-PAD is described.     

Three-electrode electrochemical detector and platinum film decoupler integrated with a capillary electrophoresis microchip for amperometric detection

This article demonstrates that a three-electrode electrochemical (EC) detector and an electric decoupler could be fabricated in the same glass chip and integrated with an O2-plasma-treated PDMS layer using microfabrication techniques to form the capillary electrophoresis (CE) microchip. The platinized decoupler could mostly decouple the electrochemical detection circuit from the interference of an separation electric field in 10 mM 2-(N-morpholino)ethanesulfonic acid (MES, pH 6.5) solution. The baseline offset of background current recorded from the working electrode with and without application of a separation electric field was maintained at less than 0.05 pA in 10 mM MES. In addition, the platinized pseudoreference electrode was demonstrated to offer a stable potential in electrochemical detection. As a consequence, the limit of detection of dopamine was 0.125 microM at a S/N = 4. The responses for dopamine to different concentrations were found to be linear between 0.25 and 50 microM with a correlation coefficient of 0.9974 and a sensitivity of 11.76 pA/microM. The totally integrated CE-EC microchip should be able to fulfill the ideal of miniaturization and commercialization.     

Development of rotating electrochemical detectors for capillary electrophoresis

A rotating disk electrode (RDE) has been evaluated and optimized for the detection of electroactive species separated by capillary electrophoresis (CE). With catechol as a working model, the limit of detection was estimated to be 0.3 microM, i.e., approximately 2.5-fold better than that of the stationary disk electrode (0.7 microM). Separation efficiency was significantly improved as exemplified by an increase of theoretical plates from 26,000 plates/m at 0 rpm to 67,000 plates/m at 500 rpm. Of particular importance was the capability of RDE to alleviate electrode passivation and electrical interference associated with high separation potential fields. Therefore, rotation amperometry was especially useful for analytes such as phenolic compounds that tended to rapidly foul the electrode surface. The RDE/ CE system was capable of separation and determination of pentachlorophenol in contaminated soils, and the result obtained agreed well with conventional liquid chromatography, an EPA recommended procedure.     

An integrated decoupler for capillary electrophoresis with electrochemical detection: application to analysis of brain microdialysate.

An approach to capillary electrophoresis with electrochemical detection (CE-EC) suitable for determination of dopamine in 1-min brain microdialysate samples is described. The CE-EC system includes an electrochemical detection cell that permits easy, precise, and permanent alignment of a carbon fiber microelectrode with a separation capillary (30-micron i.d., 75-cm length). Amperometric detection was performed at a constant applied potential of 600 mV with respect to a Ag/AgCl reference electrode. Decoupling of the electrophoretic current from the amperometric detector was accomplished with an integrated end-column decoupler prepared by etching the capillary outlet with HF. The decoupler produces baseline noise of 50 fA, or less, in the presence of 10-20-muA current in the separation capillary. The low baseline noise affords low mass (attomoles) and low concentration (nanomolar) detection limits for dopamine and 4-methylcatechol. A peak attributable to dopamine was identified in electropherograms of brain microdialysate samples obtained from anesthetized rats. Identification of the dopamine peak was confirmed by pharmacological methods. Dopamine was readily detected in 1-min brain microdialysate samples. The dopamine concentration in 1-min brain microdialysis samples was significantly altered by drug treatments and by brief electrical stimulation of dopaminergic axons.     

Phase-sensitive fluorescence lifetime detection in capillary electrophoresis

A simple and highly sensitive fluorescence lifetime detection method for capillary electrophoresis has been introduced. The detection scheme is based on the integrated phase-sensitive fluorescence intensity. The integrative nature of the method results in high sensitivity of lifetime detection. The limit of detection is 7.8 amol of fluorescein injected, representing a 2 orders of magnitude improvement over the detection limits previously reported in the UV-visible region. Rayleigh scattering, Raman scattering, and background fluorescence can be effectively suppressed by setting the detector out of the phase from the background signal. Fluorescence background can be eliminated whether the fluorescence lifetime of the background is longer or shorter than the solute molecules of interest. The signal-to-noise ratio of measurements is optimized by varying the modulation frequency and the detector phase angle.