Electro‐optic properties of CO2 fixed‐polymer/nematic LC composite films

Bis(cyclic carbonate) was obtained from the epoxide and CO₂ reaction with a quaternary ammonium halide salt catalyst. Cyclic carbonate derivatives were then reacted with amine to obtain quantitatively poly(hydroxy)urethanes that were reacted with isophorone diisocyanate (IPDI) and end capped with acrylate to form prepolymers. These prepolymers were mixed with reactive diluents and nematic LCs, and subjected to UV cure to form polymer/LC composite films in a transparent cell. Three types of diglycidyl ether [poly(propyleneglycol), cyclohexane, bisphenol A], three types of end‐capping acrylates [2‐hydroxyethyl acrylate (HEA), 2‐hydroxypropyl acrylate (HPA), and 2‐hydroxyethyl methacrylate (HEMA)], three types of multyfunctional diluents [tripropylene glycol diacrylate (TPGDA), trimethylolpropane triacrylate (TMPTA), dipentaerythritol hydroxy penta/hexa acrylate (DPHPA)], and three types of photoinitiators (Irgacure‐651, Irgacure‐184, Darocure‐1173) were incorporated to control the morphology, and hence, the electro‐optic properties of the polymer/nematic LC composite films. Poly(propylene glycol) diglycidyl ether segment of polyurethane acrylate (PUA) showed lower viscosity and gave larger domain size resulting in lower threshold (V₁₀) and driving (V₉₀) voltages, together with larger nematic–isotropic transition temperature depression. HEA end‐capped PUA gave larger polymer–LC phase separation and smaller V₁₀ as well as V₉₀. TPGDA‐based PUA showed the lowest V₁₀ and V₉₀ and the shortest response time. Among the three types of photoinitiators used Irgacure‐651 showed the larger LC domain, and smaller V₁₀ and V₉₀. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2744–2753, 2001     

Studies on electro‐optical properties of polymer matrix/LC/SiO2 nanoparticles composites

Polymer‐dispersed liquid crystal (PDLC) films were prepared by ultraviolet light‐induced polymerization of photopolymerizable monomers in nematic liquid crystal (LC)/monomers/SiO₂ nanoparticles composites, and the effect of SiO₂ nanoparticles on the electro‐optical properties of PDLC films was studied. The observed effect showed that by the adjustment of the SiO₂ nanoparticles content, the refractive index ratio of the LC and polymer could be modulated, and the electro‐optical properties of the polymer matrix/LC/SiO₂ nanoparticles composites could be optimized. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Ultraviolet‐curing behavior and mechanical properties of a polyester acrylate resin

Ultraviolet (UV) curing technology has been widely used in many applications because it has several distinct advantages compared to solvent‐based processes or thermal‐curing technology. The effects of photoinitiator types and their contents as well as reactive diluent types and their contents on the UV‐curing behavior and mechanical properties of a UV‐curable polyester acrylate resin were investigated in this study. Three photoinitiators, Irgacure 184, Darocur 1173, and benzophenone, were used in this study. Hexanediol diacrylate, tripropylene glycol diacrylate, and trimethylol propane triacrylate were used as reactive diluents to modify the properties of the acrylate resin. The change of chemical structure during UV curing was monitored by FTIR. A universal testing machine was used to measure the tensile properties of various UV‐cured acrylate films of different compositions. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3921–3928, 2004     

超支化聚氨酯丙烯酸酯的性能与UV固化动力学研究

采用2-羟基-2-甲基-1-苯基-1-丙酮（Darocur 1173）作为超支化聚氨酯丙烯酸酯（HBUA）的紫外光（UV）固化引发剂,研究了Darocur 1173用量、活性单体种类及用量对HBUA固化膜机械性能的影响,并用光差扫描量热法（Photo—DSC）对HBUA的光固化动力学进行了表征。结果表明,随着Darocur 1173用量的增加,光固化膜的摆杆硬度及冲击强度增大,最大光固化反应速率Rp^max提高,到达Rp^max的时间缩短。己二醇二丙烯酸酯（HDDA）作活性单体更有利于提高光固化膜的机械性能,并有利于促进光固化反应的进行。Darocur 1173和HDDA的适宜用量分别为4％（wt）和20％（wt）。     

Preparation and antidehydration of interpenetrating polymer network hydrogels based on 2‐hydroxyethyl methacrylate and N‐vinyl‐2‐pyrrolidone

This work reports the preparation of 2‐hydroxyethyl methacrylate (HEMA)/N‐vinyl‐2‐pyrrolidone (NVP) interpenetrating polymer network (IPN) hydrogels by UV‐initiated polymerization in the presence of free radical photoinitiator Darocur 1173 and cationic photoinitiator 4,4′‐dimethyl diphenyl iodonium hexafluorophosphate. The polymerization mechanism was investigated by the formation of gel network. The structure and morphology of the HEMA/NVP IPN hydrogels were characterized by fourier transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM). The results showed that the IPN gels exhibited homogeneous morphology. The dehydration rates of HEMA/NVP IPN hydrogels were examined by the gravimetric method. The results revealed that the hydrogels had a significant improvement of antidehydration ability in comparison with poly(2‐hydroxyethyl methacrylate)(PHEMA) hydrogel embedded physically with poly(N‐vinyl‐2‐pyrrolidone)(PVP). © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Photopolymerization behavior and phase separation effects in novel polymer dispersed liquid crystal mixture based on urethane trimethacrylate monomer

Polymer dispersed liquid crystals (PDLCs) are often formed by polymer induced phase separation, based on photopolymerization of multifunctional acrylate monomers. The emerged morphology is controlled by the interplay between polymerization rate and phase separation dynamics, which depends on different parameters such as monomer structure and functionality. In this work, a new PDLC formulation containing urethane trimethacrylate (UTMA) monomer is introduced, which has different molecular weight evolution, polymer gel point, and polymerization kinetics in comparison with some common ester acrylate (such as TMPTA and DPHPA) based PDLC compositions. UTMA is synthesized and characterized by Fourier transform infrared, ¹H‐NMR, and ¹³C‐NMR spectroscopic techniques. Simultaneous examination of polymer evolution and LC phase separation by real‐time infrared spectroscopy shows that the UTMA based PDLC, which contains trifunctional urethane acrylate monomer, has greater amount of bond conversion, polymerization rate, and liquid crystal (LC) phase separation in comparison with TMPTA based PDLC. In spite of the acrylate monomers, which show gel point conversions as low as 1.83–5.72%, UTMA reaches to its maximum rate at 19.5% conversion, which causes higher phase separation and therefore greater LC domain size. The experimental results are explained more precisely by means of SEM and optical microscopy analyses. The results are confirmed by electro‐optics measurements. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of a chiral dopant on the electro‐optical properties of polymer‐dispersed liquid‐crystal films

Polymer‐dispersed liquid crystal (PDLC) films were prepared by the ultraviolet‐light‐induced polymerization of photopolymerizable monomers in nematic liquid crystal/monomer/chiral dopant composites, and the effect of the chiral dopant on the electro‐optical properties of the PDLC films was studied. It was demonstrated that the addition of a small amount of the chiral dopant increased the driving voltage somewhat but decreased the turn‐off time significantly. Furthermore, the transmittance of ultraviolet, visible, and near‐infrared light of the off state of PDLC films showing light scattering increased with increasing content of the chiral dopant, and the optimum electro‐optical properties of the PDLC films were obtained when the content of the chiral dopant was not more than 2 wt %. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Optimization of LC droplet size and electro‐optical properties of acrylate‐based polymer‐dispersed liquid crystal by controlling photocure rate

We investigated the effects of the different content ratios of 2‐ethylhexylacrylate (2‐EHA) and 2‐ethylhexylmethacrylate (2‐EHMA) on the relationships among the photopolymerization rate, morphology of liquid crystals (LCs) droplets, and electro‐optical properties of trifunctional urethane acrylate‐based polymer‐dispersed liquid crystal (PDLC) systems. Photo‐differential scanning calorimetry (DSC) analysis and resistivity measurement revealed that increasing 2‐EHMA content gradually decreased the photocure rate of trifunctional urethane acrylate‐based PDLCs, which prolonged the phase separation between the LC molecules and the prepolymers. Morphological observations and electro‐optical measurements demonstrated that trifunctional urethane acrylate‐based PDLCs with the 2‐EHA:2‐EHMA ratios from 4:1 to 3:2 in weight percent formed the favorable microstructures of LC droplets being within the range of 1–5 µm to scatter light efficiently and showed the satisfactory off‐state opacity and on‐state transmittance and the relatively low‐driving voltage. The microstructures of LC droplets and electro‐optical properties of trifunctional urethane acrylate‐based PDLCs could be usefully optimized by controlling the photocure rate using the different 2‐EHA/2‐EHMA content ratios. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3098–3104, 2013     

Mesomomorphism enhancement of modified side‐chain liquid‐crystalline polysiloxanes by copolymerization

The liquid‐crystalline (LC) monomer 4‐allyoxybenzoyloxy‐4′‐buthylbenzoyloxy‐p‐phenyl (M₁), whose LC phase appeared at lower temperatures, from 137 to 227°C, and the modified mesogenic monomer 4‐allyoxybenzoyloxy‐4′‐methyloxybenzoyloxy‐p‐biphenyl (M₂), whose LC phase appeared at higher temperatures, from 185 to 312°C, were prepared. A series of side‐chain LC polysiloxanes containing M₁ and M₂ were prepared by graft copolymerization. Their LC properties were characterized by differential scanning calorimetry, thermogravimetric analysis, polarizing optical microscopy, and X‐ray diffraction. The results show that the introduction of the modified mesogenic monomer M₂ into the polymeric structure caused an additional increase in the clearing point (isotropic transition temperature) of the corresponding polysiloxanes, compared with unmodified polysiloxanes, but did not significantly affect the glass‐transition temperature. Moreover, the modified polysiloxanes exhibited nematic phases as the unmodified polymer did. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1196–1201, 2005     

Preparation of polymer‐dispersed liquid crystal films containing a small amount of liquid crystalline polymer and their properties

Polymer‐dispersed liquid crystal (PDLC) films were synthesized by the copolymerization of liquid crystalline polymer (LCP) precursor, urethane acrylate (UA), and mesogenic monomer (AI) at different conditions. The morphology of polymer matrix changed with the weight ratio of polymer/liquid crystal (LC) ratio and curing temperature, resulting in a large change in the droplet size of LC domains in the PDLC film. The components used in the synthesis of polymer matrix, that is, the weight ratio of LCP, AI, and UA, also strongly influenced the morphology of PDLC films. A small amount of LCP was copolymerized with UA and AI in the preparation of polymer matrix to improve the electrooptical properties such as the viewing angle. Added LCP also affected the morphology and the properties of PDLC. The hydrophobicity of LCP caused changes in the droplet size of LC domain in PDLC films and the anchoring energy between matrix polymer and LC droplets. As the hydrophobicity of the matrix increases, the droplet size of LC domain also increases; on the contrary, anchoring energy decreased, leading to the decrease of driving voltage. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 3178–3188, 2000     

Synthesis and characterization of oligomers containing the α‐aminoalkylphenone chromophore as oligomeric photoinitiator

An oligomeric photoinitiator containing α‐aminoalkylphenone photoactive chromophore in the main chain was prepared from diphenyl ether, α‐chloroisobutyryl chloride, and piperazine through acylation, bromination, epoxidation, and polycondensation. The obtained oligomeric photoinitiator was characterized by GPC, TGA, traditional DSC, FTIR, NMR, UV–vis absorption, and fluorescence spectroscopy. The number‐average molecular weight (M_n) of the oligomeric photoinitiator was determined to be 2000–4000. The excitation and emission wavelengths of the fluorescence spectra were 376 and 473 nm, respectively. The thermal stability of the oligomer was found to be perfect with a decomposition temperature greater than 300°C. All the spectroscopic and thermal analyses clearly confirmed the consistence of property and structure. In a comparative photo‐DSC investigation, the oligomeric photoinitiator showed high photoinitiating efficiency while using 1,6‐hexanediol diacrylate as monomer. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3417–3424, 2006     

Polymeric Michler's ketone photoinitiator containing coinitiator amine

Novel polymeric photoinitiator based on Michler's ketone (MK) (PMKPR) was synthesized by introducing coinitiator amine and MK into the same polymeric chain as well as the low‐molecular weight model compounds. UV–vis spectra show that PMKPR has the characteristic UV–vis absorption of MK. The photobleaching behavior of PMKPR and the model compounds were studied, indicating that the photobleaching rate of PMKPR is much faster than that of model compounds. Two types of monomer with different functionality, 2,2‐bis[4‐(acryloxypolyethoxy)phenyl] propane (A‐BPE‐10) and trimethylopropane triacrylate (TMPTA), were chosen to be initiated by these photoinitiators. The result indicates that PMKPR is an efficient photoinitiator for polymerization of A‐BPE‐10 and TMPTA. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Synthesis of 4-Methacryloylmethyldiphenylsulphone and its Copolymerization

This paper presents the synthesis of two new compounds: 4-chloromethylphenylsulphone (4-CmDPhSu) and 4-methacryloylmethylphenylsulphone (4-McMDPhSu) which are derivatives of diphenylsuphone. Introduction of the methacryloyl group into 4-CmDPhSu transferred this compound into the vinyl monomer 4-McMDPhSu. This monomer was polymerized and copolymerized with the use of two types of initiators: a mixture containing benzoyl peroxide (BP) and N,N-dimethylaniline (DMA), as well as the photoinitiators Irgacure 651 or Darocur 1173. In further studies, its copolymers with methyl methacrylate were used. Their thermomechanical properties were studied.     

Preparation and characterization of an amphiphilic macrophotoinitiator based on 2‐hydroxyl‐2‐methyl‐1‐phenylpropanone

On the basis of 2‐hydroxyl‐2‐methyl‐1‐phenylpropanone (HMPP) and poly(ethylene glycol) (PEG), we prepared amphiphilic macrophotoinitiators (HMPP–PEG–HMPP) by first reacting HMPP with isophorone diisocyanate and subsequently reacting it with PEGs with different chain lengths. Fourier transform infrared spectroscopy, high‐performance liquid chromatography, and ¹H‐NMR were used to confirm the structure of the amphiphilic macrophotoinitiators. Ultraviolet (UV) absorption spectra showed that the amphiphilic macrophotoinitiators had maximum absorption wavelengths that were similar to those of the low‐molecular‐weight photoinitiator HMPP. The photolysis rate of the amphiphilic macrophotoinitiators was slightly lower than that of HMPP, but the migration rate of the amphiphilic macrophotoinitiators from a UV‐cured matrix was much lower compared to that of HMPP. Because of their amphiphilic nature, these macrophotoinitiators may play roles as both photoinitiators and emulsifiers, and they have been applied to the solution polymerization of water‐soluble monomer acrylamide in water and the emulsion polymerization of methyl methacrylate. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43910.     

An investigation into the morphology and electro‐optical properties of 2‐hydroxy ethyl methacrylate polymer dispersed liquid crystals

Polymer dispersed liquid crystal (PDLC) films are fabricated using E7 liquid crystals, tetraethylene glycol diacrylate (TeGDA) crosslinking agent, and 0–66.49 mol % 2‐hydroxy ethyl methacrylate (HEMA). The effects of different levels of HEMA addition on the microstructure and electro‐optical properties of the PDLC samples are examined using scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and UV‐Vis spectroscopy, respectively. The results show that the refractive index of the PDLC films is insensitive to the level of HEMA addition. However, an increasing HEMA content improves the degree of phase separation during the polymerization process and increases the size and uniformity of the liquid crystal domain. As a result, the electro‐optical properties of the PDLC films are significantly improved as the level of HEMA addition is increased. Overall, the results show that a PDLC comprising 40 wt % E7 liquid crystals, 33.51 mol % TeGDA and 66.49 mol % HEMA has a high contrast ratio (13 : 1) and a low driving voltage (10 V) and is therefore an ideal candidate for a wide variety of intelligent photoelectric applications. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Electro–optic studies on polymer‐dispersed liquid crystal composite films. I. Composites of PVB–E7

The electro‐optic performance characteristic of polymer‐dispersed liquid crystal (PDLC) composite films out of poly(vinyl butyral) (PVB) and nematic liquid crystal (E7) have been studied for a wide range of PVB–E7 composite compositions (20–70 wt % of E7). Composites were prepared by solvent casting from chloroform at room temperature. A scanning electron microscopy study showed that a E7 phase is continuously embedded in chink‐like structure of PVB matrix. Optical transmittance of the composite films (of 60 and 70 wt % loading of E7) under an alternating current (ac) electric field (0–250, V_p‐p) and frequency (50 Hz to 1 KHz) were measured employing He Ne laser (λ = 632.8 nm). The results indicate that the (PVB–E7) composite exhibits a memory effect. In the memory state, higher transmittance is preserved without applying voltage. The memory state can be erased and changed to the scattering Off‐state by heating the film to the clearing temperature of the liquid crystal. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 3485–3491, 1999     

Swelling behavior of poly(n‐butyl acrylate/1,6‐hexane‐diol‐di‐acrylate)/nematic liquid crystal E7 systems: Experimental measurements and modeling by factorial design method

The swelling process of poly(n‐butyl acrylate/1,6‐hexane‐diol‐di‐acrylate) [Poly(Abu/HDDA)] networks, immersed in a liquid crystalline (LC) solvent, was investigated in order to obtain improved swelling ratio values upon application of an original method using a central composite design. The polymer/LC systems under investigation were elaborated via a photopolymerization/crosslinking phase separation process induced by UV radiation of initial mixtures composed of mono‐ and bifunctional monomers, a photoinitiator, and the low‐molar‐weight nematic LC blend E7. The parameters which strongly impact the swelling behavior of Poly(Abu/HDDA)/E7 systems were identified as temperature and concentration of the bifunctional monomer in the initial photopolymerizable mixture, thus controlling the crosslinking density of the final polymer network. The existence of interactions and synergies between these two parameters were also examined. The quality of the model was verified by a good agreement between experimental results and predicted response. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45230.     

Polymeric Michler's ketone photoinitiators: The effect of chain flexibility

Through introducing Michler's ketone (MK) moiety and diglycidyl ether monomers of different molecular chain into the same polymeric chain, polymeric photoinitiators of different chain flexibility, PMKPR, PMKPG and PMKPP were synthesized. These polymeric photoinitiators possess the similar characteristic UV–vis absorption of parent MK, and their photobleaching behavior is similar. The T_g of PMKPR, PMKPG and PMKPP is 58.1 °C, −24.9 °C and −12.5 °C, respectively. Three types of monomer with different functionality, phenoxy ethyleneglycol acrylate (AMP-10G), 2,2-bis[4-(acryloxypolyethoxy) phenyl]propane (A-BPE-10) and trimethylopropane triacrylate (TMPTA), were chosen to be initiated by these photoinitiators. The result indicates the chain structure of photoinitiators has significant influence on the polymerization of monomers. PMKPG is the most efficient polymeric photoinitiator for initiating the polymerization of AMP-10G and A-BPE-10, while PMKPP is the most efficient for TMPTA.     

Thermoplastic Polyurethane Elastomers with Aliphatic Hard Segments Based on Plant‐Oil‐Derived Long‐Chain Diisocyanates

Novel plant‐oil‐derived long‐chain (C₁₉ and C₂₃) α,ω‐diisocyanates, optionally in combination with the corresponding long‐chain diols, provide entirely aliphatic hard segments in segmented thermoplastic polyurethane elastomers (TPUs), with carbohydrate‐based poly(trimethylene glycol) soft segments. Compared to materials based on a mid‐chain monomer analog, phase separation is higher due to an increased flexibility of the aliphatic segments. Although melting points are slightly lower than for HDPE, the long‐chain TPU's solid‐state structure is still dominated by hydrogen‐bonding.     

Modification of adhesive properties of a polyethylene film by photografting

Graft polymerization of acrylic acid from monomer solutions in water or in bulk onto low‐density polyethylene film substrate was carried out by the method of continuous process under UV radiation. Effects of the nature of photoinitiator on acrylic acid grafting was first studied. One PI₂ and two PI₁ photoinitiators were used. Benzophenone was then retained for the following study. The influence of photoinitiator and monomer concentration was investigated by determining polymerization kinetics and grafted polymer amount. A study of surface wetting and morphological structure was then carried out on a bulk system and as a function of the photoinitiator concentration. Finally, such surface modification was studied with respect to its effect on the adhesion of an acrylic stick on its surface. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2803–2811, 2004