Synthesis and characterization of biodegradable lactic acid‐based polymers by chain extension

BACKGROUND: Poly(lactic acid) (PLA), coming from renewable resources, can be used to solve environmental problems. However, PLA has to have a relatively high molecular weight in order to have acceptable mechanical properties as required in many applications. Chain‐extension reaction is an effective method to raise the molecular weight of PLA. RESULTS: A high molecular weight biodegradable lactic acid polymer was successfully synthesized in two steps. First, the lactic acid monomer was oligomerized to low molecular weight hydroxyl‐terminated prepolymer; the molecular weight was then increased by chain extension using 1,6‐hexamethylene diisocyanate as the chain extender. The polymer was characterized using ¹H NMR analysis, gel permeation chromatography, differential scanning calorimetry and Fourier transform infrared spectroscopy. The results showed that the obtained polymer had a M_n of 27 500 g mol^?1 and a M_w of 116 900 g mol^?1 after 40 min of chain extension at 180 °C. The glass transition temperature (T_g) of the low molecular weight prepolymer was 47.8 °C. After chain extension, T_g increased to 53.2 °C. The mechanical and rheological properties of the obtained polymer were also investigated. CONCLUSION: The results suggest that high molecular weight PLA can be achieved by chain extension to meet conventional uses. Copyright © 2008 Society of Chemical Industry     

Polymerization of aqueous lactic acid to prepare high molecular weight poly(lactic acid) by chain-extending with hexamethylene diisocyanate

In order to synthesize the high molecular weight poly(lactic acid) [PLA], Hexamethylene diisocyanate [HDI] was used as a chain extender connecting the terminal group of polymers. Poly(lactic acid) of high molecular weight, 76000 (M_W) and 33000 (M_n), was obtained by using antimony trioxide catalyst after chain-extending with HDI. Without chain-extending, the molecular weight of PLA was about 7000 (M_n). T_m in the 2nd-scan DSC thermogram was not found when PLA was chain-extended with HDI. In order to check the degree of crystallization of polymers, annealing of these polymers was carried out at 120 °C. Peaks of XRD (X-Ray Diffraction) were sharpened as the duration of annealing was lengthened. The analysis of polymers reacted with HDI by ¹H-NMR showed the broad peaks at 1.32 and 3.14 ppm assigned to HDI units. The molecular weight of polymers increased with the increase in the mole ratio of-NCO/-OH.     

Stereocomplex formation between poly(L‐lactic acid) and poly(D‐lactic acid) with disproportionately low and high molecular weights from the melt

Poly(L ‐lactic acid) (PLLA) and poly(D ‐lactic acid) (PDLA) with very different weight‐average molecular weights (M_w) of 4.0 × 10³ and 7.0 × 10⁵ g mol^?1 (M_w(PDLA)/M_w(PLLA) = 175) were blended at different PDLA weight ratios (X_D = PDLA weight/blend weight) and their crystallization from the melt was investigated. The presence of low molecular weight PLLA facilitated the stereocomplexation and thereby lowered the cold crystallization temperature (T_cc) for non‐isothermal crystallization during heating and elevated the radial growth rate of spherulites (G) for isothermal crystallization, irrespective of X_D. The orientation of lamellae in the spherulites was higher for the neat PLLA, PDLA and an equimolar blend than for the non‐equimolar blends. It was found that the orientation of lamellae in the blends was maintained by the stereocomplex (SC) crystallites. Although the G values are expected to decrease with an increase in X_D or the content of high‐molecular‐weight PDLA with lower chain mobility compared with that of low‐molecular‐weight PLLA, G was highest at X_D = 0.5 where the maximum amount of SC crystallites was formed and the G values were very similar for X_D = 0.4 and X_D = 0.6 with the same enantiomeric excess. This means that the effect of SC crystallites overwhelmed that of chain mobility. The nucleating mechanisms of SC crystallites were identical for X_D = 0.1–0.5 in the T_c range 130–180 °C. Copyright © 2011 Society of Chemical Industry     

Highly enhanced accelerating effect of melt‐recrystallized stereocomplex crystallites on poly(L‐lactic acid) crystallization: effects of molecular weight of poly(D‐lactic acid)

The effects of the molecular weight of poly(D ‐lactic acid) (PDLA), which forms stereocomplex (SC) crystallites with poly(L ‐lactic acid) (PLLA), and those of processing temperature T_p on the acceleration (or nucleation) of PLLA homocrystallization were investigated using PLLA films containing 10 wt% PDLA with number‐average molecular weight (M_n) values of 5.47 × 10⁵, 9.67 × 10⁴ and 3.67 × 10⁴ g mol^–1 (PDLA‐H, PDLA‐M and PDLA‐L, respectively). For the PLLA/PDLA‐H and PLLA/PDLA‐M films, the SC crystallites that were ‘non’‐melted and those that were ‘completely’ melted at T_p values just above their endset melting temperature and recrystallized during cooling were found to act as effective accelerating (or nucleation) agents for PLLA homocrystallization. In contrast, SC crystallites formed from PDLA‐L, having the lowest M_n, were effective accelerating agents without any restrictions on T_p. In this case, the accelerating effects can be attributed to the plasticizer effect of PDLA‐L with the lowest M_n. The accelerating effects of SC crystallites in the PLLA/PDLA‐H and PLLA/PDLA‐M films was dependent on crystalline thickness for T_p values below the melting peak temperature of SC crystallites, whereas for T_p values above the melting peak temperature the accelerating effects are suggested to be affected by the interaction between the SC crystalline regions and PLLA amorphous regions.     

Study on biodegradable polymer materials based on poly(lactic acid). I. Chain extending of low molecular weight poly(lactic acid) with methylenediphenyl diisocyanate

Methylenediphenyl diisocyanate (MDI) was used as the chain extender for low molecular weight poly(lactic acid) (PLA) to produce high molecular weight biodegradable polymer material with a better heat resistance. PLA prepolymer with a number‐average molecular weight (M_n) of 5800 and a weight‐average molecular weight (M_w) of 9800 was produced by direct polycondensation using stannous octoate as the catalyst. After 40 min of chain extension at 175°C, the resulting polymer had a M_n of 15,000 and a M_w of 57,000. The glass transition temperature (T_g) of the low molecular weight PLA prepolymer was 48.6°C. After chain extension, the T_g of the resulting polymer was raised to 67.9°C, as determined by DSC. DMA results also indicate that the heat resistance was improved by the chain extension. The DSC spectrum and X‐ray diffraction pattern of annealed samples showed that both the crystallinity and rate of crystallization of PLA were lowered by chain‐extension reaction due to the formation of branched molecular structure. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2546–2551, 1999     

High glass transition temperature polyester coatings for the protection of stones

Copolymers of lactic acid with mandelic or salicylic acid were synthetized through ring‐opening polymerization (ROP) and tested as protective coatings for stones. Most notably, glass transition temperature (T_g), hydrophobicity, and UV barrier properties were increased, making these materials more suitable as protective coating for outdoor stones than poly(lactic acid). A T_g of 76°C was obtained for the alternating copolymer lactic acid/mandelic acid and it was considerably higher than the one of poly(lactic acid) with similar molecular weight (50–55°C). Furthermore, the introduction of a perfluorinated moiety as chain‐end group, using a perfluoro alcohol as initiator of the ROP process, allowed to increase the hydrophobicity and stability of the new coatings. These polymers showed a good protective efficiency when applied on marble stones and preliminary stability tests under solar light showed low degradation, good stability to photo‐oxidative conditions, and negligible color changes after an aging time of 1000 h. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42323.     

Preparation and characterization of polylactide‐block‐poly(butylene adipate) polyurethane thermoplastic elastomer

Polylactide‐block‐poly(butylene adipate) poly(ester‐urethane) (PLAEU) thermoplastic elastomer was obtained by melt chain extending reaction with polylactide‐block‐poly(butylene adipate)‐block‐polylactide (PBLA) and hexamethylene diisocyanate (HDI). PBLA was previously prepared with L ‐lactide and poly(butylene adipate) diol (PBA diol). Experimental parameters including feed ratio, polymerization temperature, and time were optimized. The weight average molecular weight (M_w) of PLAEU surpassed 10⁵ g/mol. In contrast to corresponding PBLA, the crystallinity and melt temperature (T_m) of PLAEU decreased, whereas its glass transition (T_g) shifted to high temperature due to the “pseudoextension” structure of polylactide (PLA) block. Additionally, the crystallinity and T_m of PLAEU were subject to crystallization method and molecular weight. The tensile strength of PLAEU varied from 6.61 to 24.41 MPa and elongation from 190% to 780%. Therefore, the mechanical properties of PLAEU can be regulated by altering the length ratio of PLA to PBA block. The high elasticity of PLAEU can be explained with phase separation mechanism. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Higher‐order structural analysis of nylon‐66 nanofibers prepared by carbon dioxide laser supersonic drawing and exhibiting near‐equilibrium melting temperature

Extended chains and/or extended chain crystals (ECC) are important structures for improving the mechanical properties of polymer fibers. ECC have so far been produced using specially prepared materials or manufacturing methods. In our study on the production of nanofibers by carbon dioxide (CO₂) laser supersonic drawing, we succeeded in producing nylon‐66 nanofibers having a high melting point near the equilibrium melting point (T_m⁰). Two melting points (T_m) of 260 and 276°C were observed for the nanofibers, with the latter temperature being close to the T_m⁰ (280°C) of nylon‐66. A nanofiber that was heat treated at 279°C for 10 min displayed a large stacked lamellar structure with an average crystal thickness of 140 nm. That value was close to the average molecular chain length of 212 nm, which was calculated from the average molecular weight of the nanofibers. It was inferred from these results that ECC corresponding to the average molecular chain length were present in the nanofibers. The CO₂ laser supersonic drawing process is applicable to general purpose thermoplastic polymers and uses a simple drawing system. It is expected that this drawing method will help to improve the fundamental performance of general purpose polymers. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40361.     

Peroxide induced cross‐linking by reactive melt processing of two biopolyesters: Poly(3‐hydroxybutyrate) and poly(l‐lactic acid) to improve their melting processability

Poly(3‐hydroxybutyrate) (PHB) and poly(l ‐lactic acid) (PLLA) were individually cross‐linked with dicumyl peroxide (DCP) (0.25–1 wt %) by reactive melt processing. The cross‐linked structures of the polymer gel were investigated by nuclear magnetic resonance (NMR) and Fourier transform infrared (FTIR) spectroscopies. The size of the polymer crystal spherulites, glass transition temperature (T_g), melting transition temperature (T_m), and crystallinity were all decreased as a result of cross‐linking. Cross‐linking density (ν_e) was shown to increase with DCP concentration. Based on parallel plate rheological study (dynamic and steady shear), elastic and viscous modulus (G″ and G′), complex viscosity (η^*) and steady shear viscosity (η) were all shown to increase with cross‐linking. Cross‐linked PHB and PLLA showed broader molar mass distribution and formation of long chain branching (LCB) as estimated by RheoMWD. Improvements in melt strength offer bioplastic processors improved material properties and processing options, such as foaming and thermoforming, for new applications. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41724.     

Preparation and characterization of high‐molecular‐weight poly(l‐lactic acid) by chain‐extending reaction with phosphites

Poly(l ‐lactic acid) (PLLA) of high molecular weight was prepared by a chain‐extending reaction in a microcompounder. Phosphites were used as chain extenders to increase the molecular weight of the PLLA prepolymer, which was prepared by the bulk polycondensation of l‐lactic acid. The effects of the amount of phosphite, the temperature, and the screw speed on the torque of the PLLA melt were studied. Under the optimal conditions, the molecular weight of PLLA increased from 62,100 to 126,000 g/mol. The chemical structure and crystallinity of PLLA were characterized by Fourier transform infrared spectroscopy, ¹H‐NMR and ¹³C‐NMR, differential scanning calorimetry, and X‐ray diffraction. The mechanical properties of PLLA were measured. The results indicate that triphenyl phosphite (TPPi) was an effective chain extender for PLLA. The role of the TPPi in chain extending is suggested to be an esterification‐promotion agent. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and properties of crystalline dicarboxylated poly(L‐lactic acid) prepolymers

Crystalline dicarboxylated poly(L ‐lactic acid)s (dcPLLAs) with number‐average molecular weights (M_n's) of 10³ to 10⁴ g/mol were synthesized via the melt polycondensation of L ‐lactic acid (LLA) in the presence of succinic anhydride (SAD), with tin(II) chloride and toluene‐4‐sulfonic acid as binary catalysts. They were characterized by end‐group titration, ¹H‐NMR, differential scanning calorimetry, and wide‐angle X‐ray diffraction. The terminal COOH percentage reached over 98%, and the molecular weight could be controlled by the molar ratio of LLA to SAD. The thermal behaviors depended on the molecular weight. The poly(L ‐lactic acid)s (PLLAs) crystallized slowly for M_n ≤ 2000 but quickly for M_n ≥ 4000. The crystallinity increased from 27 to 40% when M_n grew from 4000 to 10,000. With comparison to ordinary PLLA, the dcPLLA had the same crystallization structure but a slightly lower crystallizability. The glass‐transition temperature was clearly higher than that of amorphous dcPLLAs. With a controllable molecular weight, high COOH percentage, and crystallinity, the dcPLLA with M_n ≥ 4000 appeared to be a suitable prepolymer for the preparation of high‐molecular‐weight crystalline PLLA via chain extension. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Europium‐containing cholesteric liquid crystalline polymers in the side chain

Europium‐containing cholesteric liquid crystalline polymers were graft copolymerized using poly(methylhydrogeno)siloxane, cholesteryl 4‐(allyloxy)benzoate (M₁), cholesteryl acrylate (M₂), and a europium complexes monomer (M₃). The chemical structures of the monomers were characterized by Fourier transform infrared and ¹H‐nuclear magnetic resonance. The mesomorphic properties and phase behavior were investigated by differential scanning calorimetry, thermo gravimetric analysis, polarizing optical microscopy, and X‐ray diffraction. With an increase of europium complexes units in the polymers, the glass transition temperature (T_g) did not change significantly; the isotropic temperature (T_i) and mesophase temperature range (ΔT) decreased. All polymers showed typical cholesteric Grandjean textures, which was confirmed by X‐ray diffraction. The temperatures at which 5% weight loss occurred (T_d) were greater than 300°C for the polymers. The introduction of europium complexes units did not change the liquid crystalline state of polymer systems; on the contrary, the polymers were enabled with the significant luminescent properties. With Eu³⁺ ion contents ranging between 0 and 1.5 mol %, luminescent intensity of polymers gradually increased and luminescent lifetimes were longer than 0.45 ms for the polymers. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40866.     

Preparation and characterization of the molecular weight controllable poly(lactide-<Emphasis Type="Italic">co</Emphasis>-glycolide)

A series of poly(d,l-lactide-co-glycolide) (PLGA) polymers with various molecular weight were synthesized by a ring-opening polymerization method using stannous 2-ethyl hexanoate (Sn(Oct)₂) as the catalyst. The molecular weight of these polymers was controlled in a novel way, using t-butyldimethylsilanol (TBDS) or triphenylsilanol (TPS). The silicon-end group attached to the PLGA copolymer was removed at room temperature using either hydrochloric acid (HCl) or trifluoroacetic acid (TFA). The structures of these polymers before and after end group removal were characterized by ¹HNMR spectroscopy, while the molecular weight and polydispersity index (PDI) were determined by viscosity method and gel permeation chromatography (GPC). The residual amounts of stannum in PLGA and the glass transition temperature (T _g) of copolymer before and after end group removal were determined by the atomic absorption spectrum (AAS) and differential scanning calorimetry (DSC), respectively. The results showed that the removal method was effective. This study demonstrated that the molecular weight of PLGA could be easily controlled by altering the monomers/silanol molar ratio and the molecular weight and the purity of PLGA copolymer materials after silicon-end group removal could meet the demand of drug release.     

Synthesis and structure control of l‐lactic acid–glycolic acid copolymer by homo‐copolymerization

A two‐step direct melt copolymerization process of l ‐lactic acid (L ‐LA)/glycolic acid (GA) was developed: poly(l ‐lactic acid) (PLLA) and poly(glycolic acid) (PGA) with different molecular weight was first synthesized respectively by binary catalyst (tin chloride/p‐toluenesulfonic or tin chloride); and then poly(l ‐lactic‐co‐glycolic acid) (b‐PLGA) was produced by melt polymerization of the as‐prepared PLLA and PGA, wherein the composition and chain structure of b‐PLGA copolymers could be controlled by the molecular weight of PLLA. The chain structure and thermal properties of copolymers were studied by Wide‐angle X‐ray diffraction, nuclear magnetic resonance, differential scanning calorimetry, and thermogravimetric analysis. In comparison with the random PLGA (r‐PLGA) synthesized by one‐step direct melt polymerization, the average l ‐lactic blocks length (L_LA) in b‐PLGA was longer while the average glycolic blocks length (L_GA) in b‐PLGA was shorter which further resulted in the improved crystallinity and thermostability. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41566.     

Accelerated controlled radical polymerization of methacrylates

BACKGROUND: Nitroxide adducts 1,1‐ditertbutyl‐1‐(1‐methyl‐1‐cyanoethoxy)‐amine (AIBN/DBN), 1,1‐ditertbutyl‐1‐(benzoylperoxy)‐amine (BPO/DBN) and 2,2,6,6,‐tetramethyl‐4‐oxo‐1‐(1‐methyl‐1‐cyanoethoxy)‐piperidine (AIBN/4‐OXO‐TEMPO) were prepared and evaluated as stabilized unimolecular initiators for controlled radical polymerization of methacrylate monomers using sulfuric acid as an accelerating additive. Their effectiveness was evaluated from polymerization rates, molecular weight control and dispersity (D) of the polymers. Thermal stabilities of the polymers were also examined. The monomers used were methyl methacrylate, triethylene glycol dimethacrylate (TEGDMA) and ethoxylated bisphenol A dimethacrylate (EBPADMA). RESULTS: Polymerization was accomplished at 70 and 130 °C in 5 min to 144 h. The value of D of poly(methyl methacrylate) (PMMA) was 1.05–1.22. The glass transition temperature (T_g) for PMMA was 122–127 °C. The activity of the chain ends was established by chain extension and controlled polymerization was established by plotting M_n versus monomer conversion. First‐order kinetics in monomer consumption was established and an electron paramagnetic resonance study was conducted. Decomposition temperature (T_d) for PMMA was 360–380 °C, for poly(TEGDMA) was 300–380 °C and for poly(EBPADMA) was 360–440 °C. Photoinitiation without additive yielded no polymer. Thermal initiation by AIBN/4‐OXO‐TEMPO was the fastest. CONCLUSIONS: The initiators are applicable in low‐temperature additive‐enhanced controlled polymerization of methacylates and dimethacrylates, producing polymers with excellent attributes and a low value of D. Copyright © 2008 Society of Chemical Industry     

Synthesis,characterization, and reactivity ratios of copolymers derived from 4‐nitrophenyl acrylate and n‐butyl methacrylate

Free‐radical copolymerization of 4‐nitrophenyl acrylate (NPA) with n‐butyl methacrylate (BMA) was carried out using benzoyl peroxide as an initiator. Seven different mole ratios of NPA and BMA were chosen for this study. The copolymers were characterized by IR, ¹H‐NMR, and ¹³C‐NMR spectral studies. The molecular weights of the copolymers were determined by gel permeation chromatography and the weight‐average (M _w) and the number‐average (M _n) molecular weights of these systems lie in the range of 4.3–5.3 × 10⁴ and 2.6–3.0 × 10⁴, respectively. The reactivity ratios of the monomers in the copolymer were evaluated by Fineman–Ross, Kelen–Tudos, and extended Kelen–Tudos methods. The product of r₁, r₂ lies in the range of 0.734–0.800, which suggests a random arrangement of monomers in the copolymer chain. Thermal decomposition of the polymers occurred in two stages in the temperature range of 165–505°C and the glass transition temperature (T_g) of one of the systems was 97.2°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1817–1824, 2003     

Synthesis and characterization of soluble poly(arylene ether ketone)s with high glass transition temperature based on 3,6‐bi(4‐fluorobenzoyl)‐N‐alkylcarbazole

3,6‐bi(4‐fluorobenzoyl)‐N‐methylcarbazole and 3,6‐bi(4‐fluorobenzoyl)‐N‐ethylcarbazole were synthesized and used to prepare poly(arylene ether ketone)s (PAEKs) with high glass transition temperatures (T_g) and good solubility. High molecular weight amorphous PAEKs were prepared from these two difluoroketones with hydroquinone, phenolphthalein, 9,9‐bis(4‐hydroxyphenyl)fluorene and 4‐(4‐hydroxylphenyl)‐2,3‐phthalazin‐1‐one, respectively. All these polymers presented high thermal stability with glass transition temperatures being in the range 239–303 °C and a 5% thermal weight loss temperature above 460 °C. Compared with the T_g of phenolphthalein‐based PAEK (PEK‐C), fluorene‐based PAEK (BFEK) and phthalazinone‐based PAEK (DPEK) not containing a carbazole unit, these polymers presented a 30–50 °C increase in T_g. Meanwhile, PAEKs prepared from N‐ethylcarbazole difluoroketone showed good solubility in ordinary organic solvents, and all polymers exhibited excellent resistance to hydrochloric acid (36.5 wt%) and sodium hydroxide (50 wt%) solutions. In particular, phthalazinone‐based PAEK bearing N‐ethylcarbazole afforded simultaneously a T_g of 301 °C with good solubility. Tensile tests of films showed that these polymers have desirable mechanical properties. The carbazole‐based difluoroketones play an important role in preparing soluble PAEKs with high T_g by coordinating the relationship between chain rigidity resulting from the carbazole unit and chain distance from the side alkyl. © 2014 Society of Chemical Industry     

Thermotropic main‐chain liquid‐crystalline photodimerizable poly(vanillylidenealkyloxy alkylphosphate ester)s containing a cyclopentanone moiety

A new class of main‐chain liquid‐crystalline photodimerizable vanillylidene‐containing alkylpolyphosphate esters were synthesized from 2,5‐bis[m‐hydroxyalkyloxy(vanillylidene)] cyclopentanones with various alkylphosphoro‐ dichloridates by solution polycondensation in chloroform at ambient temperature. Their chemical structures were confirmed by FT‐IR, ¹H, ¹³C and ³¹P NMR spectroscopic analysis. Dilute‐solution viscosity values were measured in order to obtain the intrinsic viscosities of the synthesized polymers. Mesogenic properties and phase behavior were investigated by the use of hot‐stage optical polarized microscopy and differential scanning calorimetry. Thermogravimetric analysis revealed that all of the polymers were stable up to 170–230 °C and decomposed with high char yields. The shorter methylene‐chain‐containing polymers did not show a liquid‐crystalline phase, while the longer methylene‐chain‐ containing polymers showed grainy and nematic textures. The T_g, T_m and T_i values of the polymers decreased with increasing flexible methylene chain length in the polymer backbones. The photocrosslinking properties of the polymers were studied by UV light/UV spectroscopy; the crosslinking proceeds via 2π–2π cycloaddition reactions of the vanillylidene exocyclic double bonds of the polymers. The rate of crosslinking was faster for the pendant ethoxy‐containing polymers than that of the pendant methoxy‐containing polymers. Copyright © 2005 Society of Chemical Industry     

Vinyl polymerization of norbornene with dinuclear diimine nickel dichloride/MAO

Vinyl‐addition polymerization of norbornene was accomplished by two novel dinuclear diimine nickel dichloride complexes in combination with methylaluminoxane (MAO). The activities were moderate. The catalyst structure, Al/Ni molar ratio, solvents, and polymerization temperature all affected the catalytic activities. The obtained polynorbornenes were characterized by ¹H‐NMR, ¹³C‐NMR, FTIR, DSC, WAXD, and intrinsic viscosity measurements. The vinyl‐addition polymers were amorphous but with a short‐range order and high packing density. The polynorbornenes showed glass transition temperatures (T_g) above 240°C and decomposed above 400°C. The catalyst structure and polymerization conditions have effects on the molecular weight and the microstructure of the polymers. The nickel complex with bulkier substituents in the ligand produced polynorbornene with a higher packing density and higher regularity and, therefore, with higher T_g. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3273–3278, 2003     

Synthesis of star‐shaped poly(ε‐caprolactone)‐b‐poly(L‐lactide) copolymers: From star architectures to crystalline morphologies

Hexa‐armed star‐shaped poly(ε‐caprolactone)‐block‐poly(L ‐lactide) (6sPCL‐b‐PLLA) with dipentaerythritol core were synthesized by a two‐step ring‐opening polymerization. GPC and ¹H NMR data demonstrate that the polymerization courses are under control. The molecular weight of 6sPCLs and 6sPCL‐b‐PLLAs increases with increasing molar ratio of monomer to initiator, and the molecular weight distribution is in the range of 1.03–1.10. The investigation of the melting and crystallization demonstrated that the values of crystallization temperature (T_c), melting temperature (T_m), and the degree of crystallinity (X_c) of PLLA blocks are increased with the chain length increase of PLLA in the 6sPCL‐b‐PLLA copolymers. On the contrary, the crystallization of PCL blocks dominates when the chain length of PLLA is too short. According to the results of polarized optical micrographs, both the spherulitic growth rate (G) and the spherulitic morphology are affected by the macromolecular architecture and the length of the block chains. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010