Preparation and characterization of poly(L‐lactide) membranes prepared by γ‐radiation‐induced grafting of N‐vinyl pyrrolidone

A copolymer, poly(L ‐lactide)‐g‐poly(N‐vinyl pyrrolidone) (PLLA‐g‐PVP) was prepared with poly(L ‐lactide) (PLLA) and N‐vinyl pyrrolidone in the presence of methanol as a solvent by γ‐ray irradiation. The structure of PLLA‐g‐PVP was characterized by ¹H‐NMR and Fourier transform infrared spectroscopy. The PLLA‐g‐PVP graft ratio calculated by the percentage increase in weight increased with the increase of absorbed dose, and the percentage crystallinity of PLLA‐g‐PVP decreased with increasing graft ratio. The introduction of the poly(N‐vinyl pyrrolidone) chain into PLLA resulted in a decrease in the contact angle of PLLA‐g‐PVP with increasing graft ratio. In vitro degradation testing showed that PLLA‐g‐PVP had a higher degradation rate both in the weight‐loss test and molecular weight measurement because of a lower crystalline percentage and higher hydrophilicity compared to PLLA. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Medicated wound dressings based on poly(vinyl alcohol)/poly(N‐vinyl pyrrolidone)/chitosan hydrogels

Poly(vinyl alcohol)/poly(N‐vinyl pyrrolidone) (PVP)/chitosan hydrogels were prepared by a low‐temperature treatment and subsequent ⁶⁰Co γ‐ray irradiation and then were medicated with ciprofloxacin lactate (an antibiotic) and chitosan oligomer (molecular weight = 3000 g/mol). The gel content, swelling ratio, tensile strength, and crystallinity of the hydrogels were determined. The effects of the chitosan molecular weight, the low‐temperature treatment procedure, and the radiation dosage on the hydrogel properties were examined. The molecular weight of chitosan was lowered by the irradiation, but its basic polysaccharide structure was not destroyed. Repeating the low‐temperature treatment and γ‐ray irradiation caused effective physical crosslinking and chemical crosslinking, respectively, and contributed to the mechanical strength of the final hydrogels. The incorporation of PVP and chitosan resulted in a significant improvement in the equilibrium swelling ratio and elongation ratio of the prepared hydrogels. The ciprofloxacin lactate and chitosan oligomer were soaked into the hydrogels. Their in vitro release behaviors were examined, and they were found to follow diffusion‐controlled kinetics. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2453–2463, 2006     

Controlled degradation of polylactic acid grafting N‐vinyl pyrrolidone induced by gamma ray radiation

Polylactic acid (PLA) films were surface modified by gamma ray irradiation‐induced grafting of N‐vinyl pyrrolidone (NVP). The in vitro degradation behavior of polylactic acid grafting N‐vinyl pyrrolidone (PLA‐g‐PVP) copolymer was analyzed in terms of weight loss, molecular weight, and thermal properties. Grafting NVP significantly accelerated the degradation of PLA. The mass losses of the copolymers, which were less than that of pure PLA at the beginning of the degradation period, sharply accelerated with increasing degradation time. Moreover, the crystallization temperature decreased with increasing degradation time in the same graft ratio, and the degree of crystallinity increased. Cytotoxicity experiments and animal experiments in vivo were carried out to evaluate the biocompatibility of PLA‐g‐PVP copolymer. Varying graft ratios of PVP could control the degradation rate of copolymers, and thus broadening the applications of this material, such as in tissue engineering scaffolds, drug delivery, and prevention of postsurgical adhesion. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and antidehydration of interpenetrating polymer network hydrogels based on 2‐hydroxyethyl methacrylate and N‐vinyl‐2‐pyrrolidone

This work reports the preparation of 2‐hydroxyethyl methacrylate (HEMA)/N‐vinyl‐2‐pyrrolidone (NVP) interpenetrating polymer network (IPN) hydrogels by UV‐initiated polymerization in the presence of free radical photoinitiator Darocur 1173 and cationic photoinitiator 4,4′‐dimethyl diphenyl iodonium hexafluorophosphate. The polymerization mechanism was investigated by the formation of gel network. The structure and morphology of the HEMA/NVP IPN hydrogels were characterized by fourier transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM). The results showed that the IPN gels exhibited homogeneous morphology. The dehydration rates of HEMA/NVP IPN hydrogels were examined by the gravimetric method. The results revealed that the hydrogels had a significant improvement of antidehydration ability in comparison with poly(2‐hydroxyethyl methacrylate)(PHEMA) hydrogel embedded physically with poly(N‐vinyl‐2‐pyrrolidone)(PVP). © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Evaluation of two chemical crosslinking methods of poly(vinyl alcohol) hydrogels for injectable nucleus pulposus replacement

Low back pain caused by intervertebral disc degeneration is one of the most common spinal disorders among patients seeking medical treatment. The most common surgical treatments are spinal fusion and total disc arthroplasty, both of which are very invasive surgical procedures. Nucleus pulposus replacement is an earlier stage intervention for disc degeneration. One of the material classes being studied for this application is hydrogels: a three‐dimensional hydrated network of polymer(s), which mimics the mechanical and physiological properties of the nucleus. Poly(vinyl alcohol) (PVA), poly(vinyl pyrrolidone) (PVP), and poly(ethylene glycol) (PEG) hydrogels have previously been shown to be great candidate materials for injectable nucleus pulposus replacement, but have experienced issues with swelling and mass retention. The addition of chemical crosslinking to the PVA/PVP/PEG hydrogel system will allow tailoring of the swelling, mechanical, injectability, and mass loss properties of the hydrogel network. Two chemical crosslinking methods were evaluated for the PVA/PVP/PEG hydrogel system by characterizing the hydrogels with compression, swelling, and spectroscopy experiments. The results of these experiments led to the selection of the difunctional crosslinking strategy using PEG functionalized with terminal epoxide group (PEG diglycidyl ether) as the preferred crosslinking method. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40843.     

Adsorption of surfactant by hydrophobically modified poly[2‐(diethylamino)ethylmethacrylate‐co‐N‐vinyl‐2‐pyrrolidone/octadecyl acrylate)] hydrogels and effect of surfactant adsorption on the volume phase transition

Hydrophobically modified poly[2‐(diethylamino)ethylmethacrylate‐co‐N‐vinyl‐2‐pyrrolidone/octadecyl acrylate) [P(DEAEMA‐co‐NVP/OA)] hydrogels were synthesized by free‐radical crosslinking copolymerization of 2‐(diethylamino)ethylmethacrylate (DEAEMA), N‐vinyl‐2‐pyrrolidone (NVP) with different amounts of hydrophobic comonomer octadecyl acrylate (OA) in tert‐butanol with ethylene glycole dimethacrylate (EGDMA) as a crosslinker. The swelling equilibrium of the hydrogels was investigated as a function of temperature and hydrophobic comonomer content in aqueous solutions of the anionic surfactant sodium dodecyl sulfate (SDS) and the cationic surfactant dodecyltrimethylammonium bromide (DTAB). The results indicated that the swelling behavior and temperature sensitivity of the hydrogels were affected by the type and concentration of surfactant solutions. Additionally, the amount of the adsorbed SDS and DTAB molecules onto the hydrogels was determined by fluorescence measurements. An increase of OA content in the hydrogel caused an increase in the amount of adsorbed surfactant molecules in both media. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3771–3775, 2007     

Novel biodegradable amphiphilic poly(ε‐caprolactone)/poly(N‐vinylpyrrolidone) blends via successive in situ polymerizations

In this study, biodegradable blends of poly(ε‐caprolactone) (PCL) and poly(N‐vinylpyrrolidone) (PVP) were prepared by a new strategy in the following steps: (1) free radical polymerization of N‐vinyl‐2‐pyrrolidone (NVP) in ε‐caprolactone (CL); (2) ring‐opening polymerization of ε‐caprolactone in the presence of PVP to obtain the target blends. The structure of the blends was confirmed by FTIR and ¹H NMR, and the molecular weight of PCL and PVP were determined by GPC. SEM study revealed that this polymerization method could decrease the disperse phase size and improve the interphase when compared with solution‐blending method. The phase inversion occurred when PVP content was 15–20 wt %. Subsequently, the PCL sphere dispersed in PVP matrix and its size decreased with the increase of PVP content. The contact angle results showed that PVP has a profound effect on hydrophilic properties of PCL/PVP blends. PCL/PVP blends are believed to be promising for drug delivery, cell therapy, and other biomedical applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

亲水-疏水PVP-semi-IPN-PCL水凝胶的制备与溶胀性能

N-乙烯基吡咯烷酮（NVP）在聚己内酯（PCL）的乙酸乙酯溶液中进行自由基聚合,制备了亲水-疏水性聚乙烯吡咯烷酮（PVP）/聚己内酯（PCL）半互穿网络水凝胶（PVP-semi-IPN-PCL）。凝胶中PCL的熔融温度T_m无明显变化,而T_m吸热峰形状随PVP含量变化。凝胶平衡溶胀率（ESR）随PVP含量的升高而增大,结合水量的增大尤其显著。由于“笼蔽效应”,低浓度引发剂时,偶氮二异丁睛（AIBN）引发制备的凝胶ESR低于过氧化苯甲酰（BPO）引发剂。交联剂浓度较低时,以戊二醛交联形成凝胶的ESR较N,N-亚甲基双丙烯酰胺（NMBA）交联形成的凝胶大。浓度较高时,戊二醛交联凝胶ESR较NMBA低。PVP含量（质量）分别为20%、40%、60%、80%时,凝胶溶胀动力学Fick模型中的n值分别为0.854、0.471、0.466、0.253,说明在合适的PVP含量时,凝胶的溶胀动力学符合Fick模型。     

Swelling and drug‐release behavior of the poly(AA‐co‐N‐vinyl pyrrolidone)/chitosan interpenetrating polymer network hydrogels

A series of novel hydrogels were prepared from acrylic acid (AA), N‐vinyl pyrrolidone (NVP), and chitosan by photopolymerization. The swelling behavior, gel strength, and drug release behavior of the poly(AA/NVP) copolymeric hydrogels and corresponding interpenetrating polymer network hydrogels were investigated. Results showed that the swelling ratios for the present hydrogels decreased with an increase of NVP content in the gel, but the gel strength increased with an increase of NVP content in the gel. Results also showed that the drug‐release behavior for the gels is related to the ionicity of drug and the swelling ratio of the gel. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2135–2142, 2004     

Sustained delivery of hydrocortisone acetate by CS/N‐vinyl‐2‐pyrrolidone/CaCO3 microparticle hybrid hydrogels

The goal of this research is to develop a composite hydrogel system for sustained release of therapeutic agents. The hybrid hydrogels were prepared by radiation crosslinking on aqueous solution of Chitosan (CS)/N‐vinyl‐2‐pyrrolidone (NVP) with different loads of CaCO₃ in the presence of hydrocortisone acetate (HCA), an anti‐inflammatory drugs. Physical characteristics of CS/NVP/CaCO₃ were studied using X‐ray diffraction (XRD) and infrared spectrophotometery (IR). The porous structure of resulted hydrogel was confirmed by SEM micrographs. The effect of doses and calcium carbonate amount on the swelling of the hydrogels was investigated. The ability of the prepared CS/NVP/CaCO₃‐based hybrid hydrogels to be used as drug carriers for anti‐inflammatory‐specific drug delivery system was estimated using HCA as a model drug. POLYM. COMPOS., 35:1176–1183, 2014. © 2013 Society of Plastics Engineers     

Preparation and antibacterial effects of PVA‐PVP hydrogels containing silver nanoparticles

The poly(vinyl alcohol)/poly(N‐vinyl pyrrolidone) (PVA–PVP) hydrogels containing silver nanoparticles were prepared by repeated freezing–thawing treatment. The silver content in the solid composition was in the range of 0.1–1.0 wt %, the silver particle size was from 20 to 100 nm, and the weight ratio of PVA to PVP was 70 : 30. The influence of silver nanoparticles on the properties of PVA–PVP matrix was investigated by differential scanning calorimeter, infrared spectroscopy and UV–vis spectroscopy, using PVA–PVP films containing silver particles as a model. The morphology of freeze‐dried PVA–PVP hydrogel matrix and dispersion of the silver nanoparticles in the matrix was examined by scanning electron microscopy. It was found that a three‐dimensional structure was formed during the process of freezing–thawing treatment and no serious aggregation of the silver nanoparticles occurred. Water absorption properties, release of silver ions from the hydrogels and the antibacterial effects of the hydrogels against Escherichia coli and Staphylococcus aureus were examined too. It was proved that the nanosilver‐containing hydrogels had an excellent antibacterial ability. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 125–133, 2007     

Radiation crosslinking and sorption properties of hydrogels based on 1‐vinyl‐2‐pyrrolidone,hydroxyethyl methacrylate,and their copolymers

This work has been concerned with the synthesis of the hydrogels of poly (vinyl pyrrolidone) (NVP), poly (hydroxy ethylmethacrylate) (HEMA), and their copolymer under the effect of gamma radiation in the presence of N,N‐methylenebisacryl‐amide (MBAm) as a crosslinking agent. The effect of the different factors that may affect the gelation and yield product, such as solvent composition and irradiation dose, was investigated. The formed hydrogels were characterized in terms of swelling in water and different organic solvents, X‐ray diffraction (XRD), and IR spectroscopic analysis. The sorption capability of these hydrogels towards some commercial basic and acid dyesstuffs was also studied. The results showed that a solvent mixture composed of equal contents of water and methanol is the most suitable to afford the minimum sol fraction and the highest yield product at a minimal irradiation dose of 10 kGy. It was observed that NVP hydrogel displayed the highest swelling in water, alcohols, and dimethyformamide of ～1300% and a lower tendency to swell in nonpolar solvents. The results showed that HEMA hydrogel has a high affinity to absorb basic dyes while NVP has a tendency for acid dyes. Also, the sorption of either the basic or acid dyes by the different hydrogels was found to greatly depend on the concentration of dye in solution and the mass of the used hydrogel. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3274–3280, 2004     

Radiation synthesis and characterization of poly(N‐vinyl‐2‐pyrrolidone/acrylic acid) and poly(N‐vinyl‐2‐pyrrolidone/acrylamide) hydrogels for some metal‐ion separation

Two different hydrogels, prepared from N‐vinyl‐2‐pyrrolidone/acrylic acid (NVP/AAc) and N‐vinyl‐2‐pyrrolidone/acrylamide (NVP/AAm), were studied for the separation and extraction of some heavy‐metal ions from wastewater. The hydrogels were prepared by the γ‐radiation‐induced copolymerization of the aforementioned binary monomer mixtures. Further modification was carried out for the NVP/AAc copolymer through an alkaline treatment to improve the swelling behavior by the conversion of the carboxylic acid groups into its sodium salts. The thermal stability and swelling properties were also investigated as functions of the N‐vinyl‐2‐pyrrolidone content. The characterization and some selected properties of the prepared hydrogels were studied, and the possibility of their practical use in wastewater treatment for heavy metals such as Cu, Ni, Co, and Cr was investigated. The maximum uptake for a given metal was higher for a treated NVP/AAc hydrogel than for an untreated NVP/AAc hydrogel and was higher for an untreated NVP/AAc hydrogel than for an NVP/AAm hydrogel. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2642–2652, 2004     

Swelling behavior and cell viability of dehydrothermally crosslinked poly(vinyl alcohol) hydrogel grafted with N‐vinyl pyrrolidone or acrylic acid using γ‐radiation

To improve equilibrium water content, dehydrothermally crosslinked poly(vinyl alcohol) (PVA) hydrogel was grafted with N‐vinyl pyrrolidone (NVP) or acrylic acid (AA) monomer using γ‐radiation. Swelling behavior of the grafted hydrogels was studied in phosphate‐buffered saline, and cell viability was evaluated using fibroblast cells from mouse connective tissue. Equilibrium water content of AA‐ and NVP‐grafted PVA hydrogel ranged between 40–60% and 60–80%, respectively, depending on radiation dose and monomer concentration. For maximum degree of swelling, the optimum monomer concentration and radiation dose were 20% by weight and 20 kGy, respectively. Fibroblast cells seeded on NVP‐grafted hydrogel had an extended oval morphology while those seeded on AA‐grafted PVA had a rounded spherical morphology. These results support the use of NVP for grafting PVA to increase swelling and improve cell viability. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2862–2868, 2004     

NVP接枝壳聚糖水凝胶的合成与溶胀性能

合成了N-乙烯基吡咯烷酮（NVP）接枝壳聚糖（CHI）水凝胶,讨论了NVP/CHI、引发剂、交联剂、聚合温度、乙酸浓度等因素对接枝率及凝胶溶胀性能的影响,NVP∶CHI为6时,接枝率达到300%以上. 溶胀温度、pH值、盐浓度等对凝胶溶胀性能的影响实验表明,凝胶表现出温度敏感性,在40 ℃出现最大平衡溶胀率,并观察到一级相转变;在中性或弱酸性介质中溶胀性能较好;与PVP凝胶相比,NVP接枝CHI凝胶表现出反聚电解质效应. 溶胀动力学研究表明,在溶胀前期,CHI含量较高时,凝胶趋向于非Fick溶胀,说明除了溶剂扩散外,凝胶网络链段弛豫、水分子与凝胶网络间及凝胶高分子链段间相互作用对凝胶溶胀性能的影响至关重要;CHI含量较高时则趋向于Fick溶胀.     

Rheology of poly(N‐vinyl pyrrolidone)–poly(ethylene glycol) adhesive blends under shear flow

The rheological properties of adhesive miscible blends of high‐molecular‐weight poly(N‐vinyl pyrrolidone) (PVP) with short‐chain poly(ethylene glycol) (PEG) under oscillatory and steady‐state shear flow have been examined with dynamic mechanical and squeezing‐flow analysis. The latter allows the rheological characterization of adhesive blends under conditions modeling adhesive‐bond formation as a fixed compressive force is applied to an adhesive film. The most adhesive PVP blend with 36 wt % PEG has been established to flow like a viscoplastic (yield stress) liquid with a power‐law index of about 0.12. The study of the apparent yield stress as a function of the PVP–PEG composition, content of sorbed water, molecular weight of PVP, and temperature shows that the occurrence of a yield stress in the blends results most likely from a noncovalent crosslinking of PVP macromolecules through short PEG chains by means of hydrogen bonding of both terminal OH groups of PEG to the complementary functional groups in PVP monomer units. A molecular mechanism of PVP–PEG interaction was established earlier by direct and independent methods. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 522–537, 2006     

Structural insights into a novel molecular‐scale composite of soluble poly(vinyl pyrrolidone) supporting uniformly dispersed nanoscale poly(vinyl pyrrolidone) particles

Structural insights into a novel, molecular‐composite poly(vinyl pyrrolidone) consisting of a soluble, film‐forming poly(vinyl pyrrolidone) (PVP) polymer and in situ formed, minute, crosslinked, nanoscale, insoluble poly [poly(vinyl pyrrolidone)] (PPVP) polymer particles are reported. A technique for determining the PVP molecular weight and PPVP weight fraction by gel permeation chromatography/multi‐angle light scattering (MALS) is described. Particle size studies by quasi‐elastic light scattering and field flow fractionation/MALS demonstrate that the nanoscale, insoluble polymer particles are nominally 370 and 325 nm in diameter, respectively. Rheological experiments on this dispersed system yield a complex macroscopic behavior. Atomic force microscopy images confirm a substantial heterogeneous nature for a film cast from this molecular‐composite material. Finally, this polymeric molecular composite in film form exhibits, among many other interesting properties, a dramatic enhancement in water resistance, as demonstrated by a simple image water resistance test for an ink‐jet printing application. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 734–741, 2003     

Studies of UV crosslinked poly(N-vinylpyrrolidone) hydrogels by FTIR, Raman and solid-state NMR spectroscopies

Poly(N-vinylpyrrolidone) (PVP) hydrogels have become increasingly important materials for pharmaceutical and biomedical applications. UV-light initiated oxidative crosslinking of PVP represents a novel method for producing PVP based hydrogel materials. However, the mechanism of the gelation by this approach is poorly understood. In this study, the reaction mechanism for the crosslinking process is investigated by FTIR, Raman, and solid-state CP/MAS NMR techniques. Both FTIR and Raman spectra indicate that in the process of free radical oxidative crosslinking, the pyrrolidone ring is partially transformed into a succinimide ring. Solid-state NMR data have confirmed this change, and provided evidence that stable intermediates of 4-hydroperoxy-pyrrolidone (PVP-OOH) and its accompanied 4-hydroxy-pyrrolidone (PVP-OH) are formed. The pyrrolidone hydroperoxide intermediate can account for the efficient crosslinking, producing a sufficient level of macroradicals to form stable hydrogels.     

PVP单体的合成研究进展及其应用

聚乙烯吡咯烷酮 ( PVP)是 N-乙烯基吡咯烷酮 ( NVP)经自由基聚合而成的一类高分子精细化学品。我国有关 PVP的研究工作分为 PVP单体 NVP的合成研究和 NVP聚合及其聚合物的应用。本文详细讨论了合成 NVP的催化剂种类、合成方法及工艺路线 ,简单介绍了 NVP合成研究的发展趋势。     

Degradation behavior of hydrogels from poly(vinyl alcohol)‐graft‐[poly(rac‐lactide)/poly(rac‐lactide‐co‐glycolide)]: Influence of the structure and composition on the material's stability

The swellability and mass loss of poly(vinyl alcohol)‐graft‐[poly(rac‐lactide)/poly(rac‐lactide‐co‐glycolide)] hydrogels upon hydrolysis are strongly affected by the composition of the hydrogels. Hydrophobic hydrogels remain at a relatively constant mass for a couple of weeks, and the mass decreases dramatically thereafter, whereas more hydrophilic hydrogels lose mass right from the beginning. All hydrogels display water uptake values between 90 and 280% within 8 weeks. For longer periods of degradation, the water uptake increases up to a maximum of about 900%. Studies of the thermal properties of samples upon degradation and their IR measurements have shown that the degradation rate is related to the physical and chemical structure of the hydrogels and hence to the hydrophobic/hydrophilic balance; that is, the degradation increases with the increasing hydrophilicity of the material. As a result, degradation can be engineered through the variation of the composition and structure of the material. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009