Separation characteristics of acetic acid–water mixtures using poly(vinyl alcohol‐g‐4‐vinyl pyridine) membranes by pervaporation and temperature difference evapomeation techniques

The separation of acetic acid–water mixtures was carried out using pervaporation (PV) and temperature difference evapomeation (TDEV) methods. For the separation process, 4‐vinyl pyridine was grafted on poly(vinyl alcohol). Membranes were prepared from the graft‐copolymer by casting method and crosslinked by heat treatment. The effects of feed composition on the separation characteristics were studied and the performances of the separation methods were compared. Permeation rates were found to be high in PV whereas separation factors were high in TDEV method. Membranes gave permeation rates of 0.1–3.0 kg/m²h and separation factors of 2.0–61.0 depending on the composition of the feed mixture and the method. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1385–1394, 2006     

Permeation and separation characteristics of acetic acid/water mixtures through poly(vinyl alcohol‐g‐itaconic acid) membranes by pervaporation,evapomeation, and temperature‐difference evapomeation

In this study, itaconic acid (IA) was grafted onto poly(vinyl alcohol) (PVA) with cerium(IV) ammonium nitrate as an initiator at 45°C. The grafted PVA was characterized with Fourier transform infrared spectroscopy, proton nuclear magnetic resonance spectroscopy, and differential scanning calorimetry. IA‐grafted PVA membranes were prepared with a casting method, and the permeation and separation characteristics of acetic acid/water mixtures were investigated with pervaporation (PV), evapomeation (EV) and temperature‐difference evapomeation (TDEV) methods. The effects of the feed composition, operating temperature, and temperature of the membrane surroundings on the permeation rate and separation factor for the acetic acid/water mixtures were studied. The permeation rates in EV were lower than those in PV, whereas the separation factors were higher. With the TDEV method, the permeation rates decreased and the separation factors increased as the temperature of the membrane surroundings decreased. The prepared membranes were also tested in PV, EV, and TDEV to separate the various compositions of the acetic acid/water mixtures (20–90 wt % acetic acid) at 40°C. The highest separation factor, 686, was obtained in TDEV with a 90 wt % acetic acid concentration in the feed. The activation energies of permeation in PV and EV were calculated to be 8.5 and 10.2 kcal/mol, respectively, for a 20 wt % acetic acid solution. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2322–2333, 2004     

Separation of Acetic Acid‐Water Mixtures through Poly(Vinyl Alcohol)/Poly(Acrylic Acid) Alloy Membranes by Using Evapomeation and Temperature Difference Evapomeation Methods

Abstract

Separation of acetic acid‐water mixtures by using evapomeation (EV) method were carried out over the full range of compositions at temperatures varying from 30 to 55°C using poly(vinyl alcohol)/poly(acrylic acid) (PVA/PAA) (75/25) (v/v) alloy membranes. PVA/PAA membranes gave separation factors of 110–5711 and permeation rates of 2.3×10^?4–1.53×10^?1 kg/m²h, depending on the operation temperature and feed mixture composition. The temperature dependence of the permeation in EV was expressed by the Arrhenius type expression and the activation energy was calculated as 9.15 kcal/mol. More efficient EV technique, which is called temperature difference evapomeation method (TDEV) was also applied to PVA/PAA membranes to separate acetic acid‐water mixtures; high permeation rates (1.7×10^?3–3.0×10^?1 kg/m²h) and separation factors (1335–8924) were obtained for each of the studied feed compositions. Azeotropic mixture of acetic acid and water was also separated by TDEV method with a separation factor of 297 and permeation rate of 1.50×10^?1 kg/m²h.     

Separation Characteristics of Dimethylformamide/Water Mixtures through Alginate Membranes by Pervaporation,Vapor Permeation and Vapor Permeation with Temperature Difference Methods

Abstract

In this study permeation and separation characteristics of dimethylformamide (DMF)/water mixtures were investigated by pervaporation (PV), vapor permeation (VP), and vapor permeation with temperature difference (TDVP) methods using alginate membranes crosslinked with calcium chloride. The effects of membrane thickness (30–90 µm), feed composition (0–100 wt%), operating temperature (30–50°C) on the permeation rates and separation factors were investigated. The permeation rate was found to be inversely proportional to the membrane thickness whereas separation factor increased as the membrane thickness was increased. It was observed that the permeation rates in VP and TDVP were lower than in PV however the highest separation factors were obtained with TDVP method. Alginate membranes gave permeation rates of 0.97–1.2 kg/m² h and separation factors of 17–63 depending on the operation conditions and the method. In addition, sorption‐diffusion properties of the alginate membranes were investigated at the operating temperature and the feed composition. It was found that the sorption selectivity was dominant factor for the separating of DMF/water mixtures.     

Novel Poly(vinyl alcohol)‐tetraethoxysilane hybrid matrix membranes as oxygen barriers

Novel type of membranes based on poly(vinyl alcohol) crosslinked with tetraethoxysilane have been prepared by solution casting and solvent‐evaporation method. The membranes thus formed were characterized by Fourier transform infrared spectroscopy (FTIR) to study the chemical interactions, X‐ray diffraction (XRD), and thermogravimetry (TGA) to investigate morphological and thermal properties. Membranes were prepared in two different thicknesses (30 and 55 μm) and used for measuring the oxygen permeability under varying feed pressures (maintaining the desired pressure differential across the membrane) in the range from 1 to 50 kg/cm² pressure. Oxygen permeability of the membranes ranged from 0.0091 to 1.6165 Barrer for 30 μm and 0.0305 to 0.1409 Barrer for 55‐μm thick membranes by increasing the feed pressures on the feed side. Except at 50 kg/cm² pressure, the observed oxygen permeability values are almost close to total permeability. Membranes of this study could be useful as oxygen barriers for applications in food packaging industries. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 273–278, 2007     

Poly(acrylic acid)–poly(vinyl alcohol) semi- and interpenetrating polymer network pervaporation membranes

A series of poly(acrylic acid) (PAA)–poly(vinyl alcoho) (PVA) semiinterpenetrating (SIPN) and interpenetrating (IPN) polymer network membranes were prepared by crosslinking PVA alone or by crosslinking both PVA and PAA. Glutaraldeyde and ethylene glycol were used as crosslinking agents for the PVA and PAA networks, respectively. The presence of PAA increases the permeability of the membranes while the presence of PVA improves their mechanical and film-forming properties. The mechanical properties of the membranes were investigated via tensile testing. These hydrophilic membranes are permselective to water from ethanol–water mixture and to ethanol from ethanol–benzene mixtures. The IPN membranes were employed for the former mixtures and the SPIN membranes for the latter, because the IPN ones provided too low permeation rates. The permeation rates and seperation factors were determined as functions of the IPN or SIPN composition, feed composition, and temperature. For the azeotropic ethanol–water mixture (95 wt % ethanol), the separation factor and permeation rate at 50°C of the PAA-PVA IPN membrane, containing 50 wt % PAA, were 50 and 260 g/m²h, respectively. For the ethanol–benzene mixture, the PAA–PVA SIPN membranes had separation factors between 1.4 and 1200 and permeation rates between 6 and 550 g/m²h, respectively, depending on the feed composition and temperature. © 1996 John Wiley & Sons, Inc.     

Use of Sodium Alginate-Poly(vinyl pyrrolidone) Membranes for Pervaporation Separation of Acetone/Water Mixtures

Pervaporative separation of acetone from water at a concentration range of 0–100 wt% were studied using sodium alginate (NaAlg)/Poly vinyl pyrrolidone (PVP) membranes. Membranes were prepared in different ratios (w/w) (100/0, 95/5, 90/10, 85/15, 80/20, 75/25) of NaAlg/PVP by crosslinking with CaCl₂. Experimental studies were carried out to investigate the effects of the operating temperature, feed composition, and membrane thickness on the pervaporation performance. The optimum operating temperature, membrane thickness, NaAlg/PVP ratio, and feed composition were determined as 40°C, 70 µm, 75/25 (w/w), and 20 wt% acetone, respectively. The effect of PVP content in the membranes was investigated on pervaporation performance. The permeation rate was increased with increasing the PVP content; however, there was no appreciable change about the separation factor. The permeation rate and separation factor values were found to be in the range of 0.304–1.023 kg/m² h and 16–57, respectively. In addition, the sorption-diffusion properties of the alginate membranes were investigated at the operating temperature and the feed composition. It was found that the sorption selectivity was the dominant factor for the separation of acetone/water mixtures.     

Permeation and Separation Characteristics of Acetic Acid‐Water Mixtures by Pervaporation through Acrylonitrile and Hydroxy Ethyl Methacrylate Grafted Poly(vinyl alcohol) Membrane

Abstract

In this study, acrylonitrile (AN) and hydroxyl ethyl methacrylate (HEMA) were grafted onto poly(vinyl alcohol) (PVA) using cerium (IV) ammonium nitrate as initiator at 30°C. The graft copolymer was characterized using the Fourier transform infrared spectroscopy (FTIR) and elemental analysis. The grafted PVA membranes (PVA‐g‐AN/HEMA) were prepared by a casting method, and used in the separation of acetic acid‐water mixtures by pervaporation. The effects of the membrane thickness, operating temperature, and feed composition on the permeation rate and separation factor for acetic acid‐water mixtures were studied. Depending on the membrane thickness, the temperature and feed composition PVA‐g‐AN/HEMA membranes gave separation factors 2.26–14.60 and permeation rates of 0.18–2.07 kg/m²h. It was also determined that grafted membranes gave lower permeation rates and greater separation factors than PVA membranes. Diffusion coefficients of acetic acid‐water mixtures were calculated from permeation rate values. The Arrhenius activation parameters were calculated for the 20 wt.% acetic acid content in the feed using the permeation rate and the diffusion data obtained at between 25–50°C.     

Preparation of PFSA‐PVA/PSf hollow fiber membrane for IPA/H2O pervaporation process

Using Na⁺ form of perfluorosulfonic acid (PFSA) and poly(vinyl alcohol) (PVA) as coating materials, polysulfone (PSf) hollow fiber ultrafiltration membrane as a substrate membrane, PFSA‐PVA/PSf hollow fiber composite membrane was fabricated by dip‐coating method. The membranes were post‐treated by two methods of heat treatment and by both heat treatment and chemical crosslinking. Maleic anhydride (MAC) aqueous solution was used as chemical crosslinking agent using 0.5 wt % H₂SO₄ as a catalyst. PFSA‐PVA/PSf hollow fiber composite membranes were used for the pervaporation (PV) separation of isopropanol (IPA)/H₂O mixture. Based on the experimental results, PFSA‐PVA/PSf hollow fiber composite membrane is suitable for the PV dehydration of IPA/H₂O solution. With the increment of heat treatment temperature, the separation factor increased and the total permeation flux decreased. The addition of PVA in PFSA‐PVA coating solution was favorable for the improvement of the separation factor of the composite membranes post‐treated by heat treatment. Compared with the membranes by heat treatment, the separation factors of the composite membranes post‐treated by both heat treatment and chemical crosslinking were evidently improved and reached to be about 520 for 95/5 IPA/water. The membranes post‐treated by heat had some cracks which disappeared after chemical crosslinking for a proper time. Effects of feed temperature on PV performance had some differences for the membranes with different composition of coating layer. The composite membranes with the higher mass fraction of PVA in PFSA‐PVA coating solution were more sensitive to temperature. It was concluded that the proper preparation conditions for the composite membranes were as follows: firstly, heated at 160°C for 1 h, then chemical crosslinking at 40°C for 3 h in 4% MAC aqueous solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Nonionic water‐soluble polymer: Preparation,characterization, and application of poly(1‐vinyl‐2‐pyrrolidone‐co‐hydroxyethylmethacrylate) as a polychelatogen

The free‐radical copolymerization of water‐soluble poly(1‐vinyl‐2‐pyrrolidone‐co‐hydroxyethylmethacrylate) was carried out with a feed monomer ratio of 75:25 mol %, and the total monomer concentration was 2.67M. The synthesis of the copolymer was carried out in dioxane at 70°C with benzoyl peroxide as the initiator. The copolymer composition was obtained with elemental analysis and ¹H‐NMR spectroscopy. The water‐soluble polymer was characterized with elemental analysis, Fourier transform infrared, ¹H‐ and ¹³C‐NMR spectroscopy, and thermal analysis. Additionally, viscosimetric measurements of the copolymer were performed. The thermal behavior of the copolymer and its complexes were investigated with differential scanning calorimetry (DSC) and thermogravimetry techniques under a nitrogen atmosphere. The copolymer showed high thermal stability and a glass transition in the DSC curves. The separation of various metal ions by the water‐soluble poly(1‐vinyl‐2‐pyrrolidone‐co‐hydroxyethylmethacrylate) reagent in the aqueous phase with liquid‐phase polymer‐based retention was investigated. The method was based on the retention of inorganic ions by this polymer in a membrane filtration cell and subsequent separation of low‐molar‐mass species from the polymer/metal‐ion complex formed. Poly(1‐vinyl‐2‐pyrrolidone‐co‐hydroxyethylmethacrylate) could bind metal ions such as Cr(III), Co(II), Zn(II), Ni(II), Cu(II), Cd(II), and Fe(III) in aqueous solutions at pHs 3, 5, and 7. The retention percentage for all the metal ions in the polymer was increased at pH 7, at which the maximum retention capacity could be observed. The interaction of inorganic ions with the hydrophilic polymer was determined as a function of the pH and filtration factor. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 178–185, 2006     

Pervaporation of 1,2‐dimethoxyethane from aqueous solutions by crosslinked oligosilylstyrene–poly(dimethylsiloxane) composite membranes

Crosslinked oligosilylstyrene–poly(dimethylsiloxane) composite membranes were used to separate 1,2‐dimethoxyethane (1,2‐DME) from dilute aqueous solutions through a pervaporation process. The composite membranes were prepared through the casting of solutions of H‐terminated oligosilylstyrene and vinyl‐terminated poly(dimethylsiloxane) onto the surfaces of polysulfone ultrafiltration membranes. A crosslinked poly(dimethylsiloxane) gel was generated through the reaction of H‐terminated oligosilylstyrene and vinyl‐terminated poly(dimethylsiloxane), with a platinum complex used as a catalyst. The pervaporation characteristics of the composite membranes were investigated with respect to the feed composition of 1,2‐DME, the feed temperature, the downstream pressure, and the top‐layer thickness of the composite membranes. The composite membranes exhibited preferential selectivity to 1,2‐DME. Depending on the operation conditions, the separation factor and permeation rate of 1,2‐DME were 55–184 and 0.31–3.3 g/m² h, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2284–2294, 2004     

Pervaporation separation of water/dimethylformamide mixtures using poly(vinyl alcohol)‐g‐polyacrylamide copolymeric membranes

Grafted copolymeric membranes of poly(vinyl alcohol) with acrylamide (PVA‐g‐AAm) were developed and used in the pervaporation separation of water–dimethylformamide mixtures by varying the amount of water in the feed from 0 to 100%. From these data, the permeation flux, pervaporation separation index, diffusion coefficient, swelling index, and separation selectivity were calculated at 25, 35, and 45°C. The Arrhenius activation parameters for permeation flux ranged between 22 and 63 kJ/mol, while the activation energy for diffusion ranged between 23 and 67 kJ/mol. Separation selectivity was between 15 and 22. The highest permeation flux of 0.459 kg m^?2 h^?1 was obtained for the 93% grafted membrane at 90% of water in the feed mixture. The results are discussed using the principles of the solution–diffusion model. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 273–282, 2002     

Pervaporation separation of isopropanol–water mixtures using mixed matrix blend membranes of poly(vinyl alcohol)/poly(vinyl pyrrolidone) loaded with phosphomolybdic acid

Mixed matrix membranes of poly(vinyl alcohol) and poly(vinyl pyrrilidone) blends were prepared by loading with phosphomolybdic acid (PMA) and their pervaporation (PV) properties were investigated for the PV separation of isopropanol. Membrane performance shown a dependence on the extent of PMA loading. The 4 wt % PMA‐loaded blend membrane had the highest separation factor of 29991, which declined considerably at higher loading. The flux of 4 wt % PMA‐loaded membrane was lower than that of nascent blend membrane. Feed water composition and temperature influenced the PV performance. Solubility selectivity was higher than diffusion selectivity. Degree of swelling was smaller after PMA loading exhibiting better separation ability. The PV results were analyzed using the Flory‐Huggins theory and sorption was dominated by Langmuir's mode. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Pervaporation separation of acetic acid-water mixtures using modified membranes. I. Blended polyacrylic acid (PAA)-nylon 6 membranes

Membranes consisting of ionically crosslinked polyacrylic acid (PAA) and Nylon 6 were prepared and tested for the pervaporation separation of acetic acid-water mixtures. The polyacrylic acid (PAA) membranes were crosslinked in aluminum nitrate aqueous solution while the polyacrylic acid (PAA)-Nylon 6 blends were cast from homogeneous PAA-Nylon 6 mixtures to appropriate thicknesses and then crosslinked in aqueous aluminum nitrate solutions. Optimum pervaporation results were obtained from blends of Nylon 6 and PAA in the weight ratio of 60–75 wt% Nylon 6 and 25–40 wt% PAA which have separation factors (water/acetic acid) of over 60 and flux rates higher than 100 g/m² h at 15°C for the separation of acetic acid-water mixtures. The flux rates and separation factors could be altered by changing the blend composition of the membrane. The effects of the feed composition on the separation factors were investigated.     

Microstructure determination and thermal studies of n‐acryloylcarbazole/vinyl acetate copolymers

Copolymers of N‐acryloylcarbazole (A) and vinyl acetate (V) were synthesized by bulk polymerization using benzoyl peroxide (BPO) as free‐radical initiator at 65°C in different in‐feed ratios. The composition of the copolymer was determined by ¹H‐NMR spectrum. The comonomer reactivity ratios, determined by Kelen–Tudos (KT) and nonlinear error‐in‐variables (EVM) methods, were r_A= 16.75 ± 1.38, r_V = 0.015 ± 0.002, and r_A = 16.36, r_V = 0.015, respectively. Complete spectral assignments of the ¹H and ¹³C{¹H} NMR spectra of the copolymers were done by the help of distortionless enhancement by polarization transfer (DEPT) and two‐dimensional NMR techniques such as heteronuclear single quantum coherence (HSQC) and total correlation spectroscopy (TOCSY). The methine and methylene carbon resonances were found to be compositional as well as configurational sensitive. The signals obtained were broad pertaining to the restricted rotation of bulky carbazole group. The thermal stability and glass‐transition temperatures (T_g) of the copolymers were found to be dependant on polymer composition and characteristic of rotational rigidity of the polymer chain. Variation in the values of T_g with the copolymer composition was found to be in good agreement with theoretical values obtained from Johnston and Barton equations. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2720–2733, 2007     

Pervaporation characteristics and structure of poly(vinyl alcohol)/poly(ethylene glycol)/tetraethoxysilane hybrid membranes

Poly(vinyl alcohol) (PVA) blended with poly(ethylene glycol) (PEG) was crosslinked with tetraethoxysilane (TEOS) to prepare organic–inorganic PVA/PEG/TEOS hybrid membranes. The membranes were then used for the dehydration of ethanol by pervaporation (PV). The physicochemical structure of the hybrid membranes was studied with Fourier transform infrared spectra (FT‐IR), wide‐angle X‐ray diffraction WXRD, and scanning electron microscopy (SEM). PVA and PEG were crosslinked with TEOS, and the crosslinking density increased with increases in the TEOS content, annealing temperature, and time. The water permselectivity of the hybrid membranes increased with increasing annealing temperature or time; however, the permeation fluxes decreased at the same time. SEM pictures showed that phase separation took place in the hybrid membranes when the TEOS content was greater than 15 wt %. The water permselectivity increased with the addition of TEOS and reached the maximum at 10 wt % TEOS. The water permselectivity decreased, whereas the permeation flux increased, with an increase in the feed water content or feed temperature. The hybrid membrane that was annealed at 130°C for 12 h exhibited high permselectivity with a separation factor of 300 and a permeation flux of 0.046 kg m^?2 h^?1 in PV of 15 wt % water in ethanol. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Divinyl benzene cross‐linked HTPB‐based polyurethaneurea membranes for separation of p‐/o‐xylene mixtures by pervaporation

Cross‐linked hydroxy terminated polybutadiene (HTPB)‐based polyurethaneurea (PU), HTPB‐divinyl benzene (DVB)‐PU, was synthesized by a three‐step polymerization process. It was first used as membrane material to separate p‐/o‐xylene mixtures by pervaporation (PV). The effects of the content of cross‐linker DVB, feed concentration, and operating temperature on the PV performance of HTPB‐DVB‐PU membranes were investigated. The membranes demonstrated p‐xylene permselectivity as well as high total flux. The introduction of DVB significantly enhanced the temperature resistance ability of the HTPB‐DVB‐PU membranes. With increasing DVB content, the separation factor increased while the total flux decreased a little. The highest separation factor reaches 2.01 and the total flux is 33 g/m²h with feed concentration of 10 wt % p‐xylene at 30°C. These PV performances with increasing DVB content were explained in terms of the view point of chemical compositions and physical structures of the HTPB‐DVB‐PU membranes. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Water‐soluble copolymers of 1‐vinyl‐2‐pyrrolidone and acrylamide derivatives: synthesis,characterization, and metal binding capability studied by liquid‐phase polymer‐based retention technique

Radical copolymerizations of 1‐vinyl‐2‐pyrrolidone with acrylamide and N,N′‐dimethylacrylamide at different feed ratios were investigated. The copolymers were characterized by Fourier transform infrared spectroscopy, ¹H NMR, and ¹³C NMR spectroscopy. The copolymer composition was determined from the ¹H NMR spectra and found to be statistical. The metal complexation of poly(acrylamide‐co‐1‐vinyl‐2‐pyrrolidone) and poly(N,N′‐dimethylacrylamide‐co‐1‐vinyl‐2‐pyrrolidone) for the metal ions Cu(II), Co(II), Ni(II), Cd(II), Zn(II), Pb(II), Fe(III), and Cr(III) were investigated in an aqueous phase. The liquid‐phase polymer‐based retention method is based on the retention of inorganic ions by soluble polymers in a membrane filtration cell and subsequent separation of low‐molecular compounds from the polymer complex formed. The metal ion interaction with the hydrophilic polymers was determined as a function of the pH and the filtration factor. Poly(N,N‐dimethylacrylamide‐co‐1‐vinyl‐2‐pyrrolidone) showed a higher affinity for the metal ions than poly(acrylamide‐co‐1‐vinyl‐2‐pyrrolidone). According to the interaction pattern obtained, Cr(III) and Cu(II) formed the most stable complexes at pH 7. Pb(II) and Zn(II) were not retained. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 741–750, 1999     

Modified poly(vinyl alcohol)/chitosan blended membranes for isopropanol dehydration via pervaporation: Synthesis optimization and modeling by response surface methodology

Box–Behnken (BB) design of response surface methodology (RSM) was effectively applied to optimize fabrication conditions of modified poly(vinyl alcohol) (PVA) and chitosan (CS) blended pervaporation (PV) membranes. The PVA/CS membranes were crosslinked either by chemical reaction with glutaraldehyde (GA) or by heat‐treating at different temperatures. The main objectives were to determine the optimal levels of fabricating parameters and also to investigate interactions among the variables. CS content in the blended membranes, concentration of crosslinking agent and heat‐treating temperature were the fabrication parameters, the main effects and interaction effects of which on membrane structure and PV performance toward isopropanol (IPA)/water dehydration were investigated, and for which regression models were established. The modified PVA/CS blended membranes were characterized by means of scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) as well as X‐ray diffraction (XRD). It was found that the CS content is the most significant factor influencing flux and separation factor among the three studied variables and the experimental results are in excellent accordance with predicted values from the developed RSM regression models. The RSM results indicated that under preparation conditions of 80 wt % CS in the blended membrane, 0.58 wt % GA concentration, and 77 °C heat‐treating temperature, the maximum separation factor of 5222.8 and the normalized flux of 9.407 kg µm/m²h can be acquired with feed content of 85 wt % IPA at 25 °C, showing that the prepared membrane is highly efficient for PV dehydration of IPA. The models were satisfactorily validated against experimental data. Furthermore, the optimum membrane presents excellent separation performance at different feed compositions and temperatures. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44587.     

Silicalite‐Filled PEBA Membranes for Recovering Ethanol from Aqueous Solution by Pervaporation

Pervaporation (PV) performances of silicalite‐filled polyether‐block‐amide (PEBA) membranes for separation of ethanol/water mixtures have been studied. The effects of silicalite content, ethanol concentration in feed, and feed temperature on the PV performances of the membranes have been investigated. It is found that addition of silicalite can improve PV performances of PEBA membranes. When the silicalite content is 2.0 wt %, both permeation flux and separation factor reach the maximum values, which are 833 g/m²h and 3.6, respectively. With increasing of ethanol in the feed and feed temperature, both separation factor and total flux increased. The higher permeation activation energy of ethanol (E_ethanol = 21.62 kJ/mol) compared to that of water (E_water = 18.33 kJ/mol) for the 2.0 wt% silicalite‐filled PEBA membrane accounts for the increase of the separation factor with feed temperature.