Synthesis and thermal properties of poly(urethane‐imide)

The synthesis and thermal properties of thermoplastic poly(urethane‐imide) (PUI) resins were studied. Model reaction studies on the reactions of 4,4′‐diphenylcarbamatodiphenylmethane and 4,4′‐diisocyanatodiphenylmethane with phthalic anhydride were performed. We found that the reaction of anhydrides with urethane groups could take place under certain reaction conditions. According to the model reaction studies, N‐2‐methyl‐pyrrolidone was employed as a solvent, and no catalyst was used in the polymerization. To restrain the side reaction of anhydrides with urethane groups, we adopted a two‐step chain‐extending procedure in a chain‐extending reaction. The inherent viscosity of PUI was 0.83–0.99 dL/g. The prepared polymers not only exhibited improved solubility in organic solvents but also formed flexible films. Thermogravimetric analysis showed that PUI exhibited a two‐step thermal weight‐loss pattern. The first step of the thermal degradation of PUI was attributed to the thermooxidizing cleavage of weak and labile linkage, such as urethane groups, isopropylidene, and methylene, except for imide rings. The polymer inherent viscosity decreased sharply during the first step of thermal degradation. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 773–781, 2001     

Synthesis of poly(amide‐ester)s by microwave methods

The polycondensation of sebacic acids and ω‐amino alcohols by microwave irradiation was studied. The results were compared to those obtained from conventional melt polycondensation of poly(amide‐ester)s. It was found that the reaction proceeded at a much higher rate upon microwave irradiation. A high yield of thermally stable poly(amide‐ester)s was obtained. The microwave‐synthesized compounds were fully characterized by FTIR and ¹H‐NMR spectroscopy, gel permeation chromatography, and a solubility test. The thermal properties of the poly(amide‐ester)s also were investigated. The results showed that the chemical‐physical properties of the polymers were in good agreement with those of polymers obtained by conventional synthesis. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1952–1958, 2007     

Preparation and properties of flame retardant poly(urethane‐imide)s containing phosphine oxide moiety

The preparation of new poly(urethane‐imide)s (PUIs) having acceptable thermal stability and higher flame resistance was aimed. Two new aromatic diisocyanate‐containing methyldiphenylphosphine oxide and triphenylphosphine oxide moieties were synthesized via Curtius rearrangement in situ and polymerized by various prepared diols. Four aliphatic hydroxy terminated aromatic based diols were synthesized by the reaction between ethylene carbonate and various diphenolic substances. Chemical structures of monomers and polymers were characterized by FTIR, ¹H NMR, ¹³C NMR, and ³¹P NMR spectroscopy. Thermal stabilities and decomposition behaviors of the PUIs were tested by DSC and TGA. Thermal measurements indicate that the polymers have high thermal stability and produce high char. Polymers exhibit quite high fire resistance, evaluated by fire test UL‐94. The films of the polymers were prepared by casting the solution. Inherent viscosities, solubilities, and water absorbtion behaviors of the polymers were reported in. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of biodegradable poly(ester‐urethanes) based on bacterial poly(R‐3‐hydroxybutyrate)

A series of poly(R‐3‐hydroxybutyrate)/poly(ε‐caprolactone)/1,6‐hexamethylene diisocyanate‐segmented poly(ester‐urethanes), having different compositions and different block lengths, were synthesized by one‐step solution polymerization. The molecular weight of poly(R‐3‐hydroxybutyrate)‐diol, PHB‐diol, hard segments was in the range of 2100–4400 and poly(ε‐caprolactone)‐diol, PCL‐diol, soft segments in the range of 1080–5800. The materials obtained were investigated by using differential scanning calorimetry, wide angle X‐ray diffraction and mechanical measurements. All poly(ester‐urethanes) investigated were semicrystalline with T_m varying within 126–148°C. DSC results showed that T_g are shifted to higher temperature with increasing content of PHB hard segments and decreasing molecular weight of PCL soft segments. This indicates partial compatibility of the two phases. In poly(ester‐urethanes) made from PCL soft segments of molecular weight (M_n ≥ 2200), a PCL crystalline phase, in addition to the PHB crystalline phase, was observed. As for the mechanical tensile properties of poly(ester‐urethane) cast films, it was found that the ultimate strength and the elongation at the breakpoint decrease with increasing PHB hard segment content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 703–718, 2002     

The effect of the soft segment of prepolymers on properties of poly(urethane‐ester) and its biodegradability

The influence of soft‐segment prepolymers prepared through the polymerization of δ‐valerolactone (VL) and 2,2‐dimethyl‐1,3‐propandiol (DP) monomers on the structure and properties of poly(urethane‐ester) as well as its biodegradability were investigated. Poly(urethane‐ester) was prepared in two steps. The first step was the preparation of prepolymers with various chain lengths by polymerizing VL and DP monomers in the presence of a distannoxane catalyst at 100 °C under nitrogen atmosphere. The second step was the preparation of poly(urethane‐ester) by polymerizing 4,4′‐methylene‐bis(phenyl isocyanate) (MDI) and prepolymers with various chain lengths in the absence of catalysts. The poly(urethane‐ester) was characterized through an analysis of functional groups (FTIR), thermal properties (differential thermal analysis/TGA), mechanical properties (tensile tester), crystallinity (XRD) and biodegradability. An increased chain length of the prepolymer used in polymerization with MDI leads to an increase in the thermal properties and crystallinity of poly(urethane‐ester). However, the maximum biodegradability in the activated sludge was observed in the poly(urethane‐ester) prepared by polymerizing MDI and prepolymers with a molar VL/DP ratio of 20/1. The amorphous parts of polymers were more easily decomposed by microorganism enzymes than were the crystalline parts after an incubation period of 30 days. Copyright © 2011 Society of Chemical Industry     

Synthesis,characterization, and pervaporation properties of segmented poly(urethane‐urea)s

Poly(urethane‐urea)s (PUUs) from 2,4‐tolylene diisocyanate (2,4‐TDI), poly(oxytetramethylene)diols (PTMO) or poly(butylene adipate)diol (PBA), and various diamines were synthesized and characterized by Fourier transform infrared spectroscopy, gel permeation chromatography, differential scanning calorimetry, and density measurements. Transport properties of the dense PUU‐based membranes were investigated in the pervaporation of benzene–cyclohexane mixtures. It was shown that the pervaporation characteristics of the prepared membranes depend on the structure and length of the PUU segments. The PBA‐based PUUs exhibit good pervaporation performance along with a very good durability in separation of the azeotropic benzene–cyclohexane mixture. They are characterized by the flux value of 25.5 (kg μm m⁻² h⁻¹) and the separation factor of 5.8 at 25°C, which is a reasonable compromise between the both transport parameters. The PTMO‐based PUUs display high permeation flux and low selectivity in separation of the benzene‐rich mixtures. At the feed composition of 5% benzene in cyclohexane, their selectivity and flux are in the range of 3.2 to 11.7 and 0.4 to 40.3, respectively, depending on the length of the hard and soft segments. The chemical constitution of the hard segments resulting from the chain extender used does not affect the selectivity of the PUU membranes. It enables, however, the permeability of the membranes to be tailored. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1615–1625, 1999     

Synthesis and characterization of novel thermoplastic poly(oligophosphazene‐urethane)s

BACKGROUND: Polyurethanes are some of the most popular polymers used in a variety of products, such as coatings, adhesives, flexible and rigid foams, elastomers, etc. Despite the possibility of tailoring their properties, polyurethanes suffer a serious disadvantage of poor thermal stability. Many attempts have been made in order to improve the thermal stability of polyurethanes. RESULTS: A new hydroxyl‐terminated oligomer containing sulfone groups, 2,2‐bis(4‐hydroxy‐4,4‐sulfonyldiphoneloxy)tetraphenoxyoligocyclotriphosphazene (HSPPZ), was synthesized. HSPPZ was characterized using Fourier transform infrared (FTIR), NMR and gel permeation chromatography analyses. A series of novel thermoplastic poly(oligophosphazene‐urethane)s were then synthesized via the reaction of NCO‐terminated polyurethane prepolymer with HSPPZ containing chain‐extender diols. Their structure and properties were investigated using FTIR spectroscopy, thermogravimetric analysis, differential scanning calorimetry, X‐ray diffraction, water contact angle measurement and tensile measurements. CONCLUSION: Compared to conventional thermoplastic polyurethanes, poly(oligophosphazene‐urethane)s exhibit better thermal stability, low‐temperature resistance and hydrophobicity, but their mechanical properties are slightly poorer. Copyright © 2009 Society of Chemical Industry     

The effect of processing routes on the thermal and mechanical properties of poly(urethane‐isocyanurate) nanocomposites

A systematic investigation of four processing routes was implemented so as to evaluate the thermal and mechanical properties of nanosilica (NS) reinforced poly(urethane‐isocyanurate) nanocomposites (NC). The NS dispersion in the Polmix and the Isomix routes was performed in the polyol and the isocyanate precursor, respectively. The Isopol and the Solvmix routes consisted on the dispersion of the filler after the mixing of the precursors and with the aid of solvents, respectively. The NS dispersion, fractography (SEM, TEM), flexural and tensile mechanical properties, thermogravimetric analysis and FTIR analysis of NCs was performed as a function of processing route, isocyanate index, and NS concentration. Each route produced a NC with distinct properties, which were correlated to the NS agglomeration degree and how the NS affected the thermal transitions of the HS and the relative ratio of urethane and isocyanurate chemical groups. For example, the NC prepared with the Polmix route had substantial improvements of σ_t and ε_t of around +40 and +52%, respectively and an improved thermal resistance of the Hard Segments. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42750.     

Synthesis and characterization of hyperbranched poly(silyl ester)s

Hyperbranched poly(silyl ester)s were synthesized via the A₂ + B₄ route by the polycondensation reaction. The solid poly(silyl ester) was obtained by the reaction of di‐tert‐butyl adipate and 1,3‐tetramethyl‐1,3‐bis‐β(methyl‐dicholorosilyl)ethyl disiloxane. The oligomers with tert‐butyl terminal groups were obtained via the A₂ + B₂ route by the reaction of 1,5‐dichloro‐1,1,5,5‐tetramethyl‐3,3‐diphenyl‐trisi1oxane with excess amount of di‐tert‐butyl adipate. The viscous fluid and soft solid poly(silyl ester)s were obtained by the reaction of the oligomers as big monomers with 1,3‐tetramethyl‐1,3‐bis‐β(methyl‐dicholorosilyl)ethyl disiloxane. The polymers were characterized by ¹H NMR, IR, and UV spectroscopies, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The ¹H NMR and IR analysis proved the existence of the branched structures in the polymers. The glass transition temperatures (T_g's) of the viscous fluid and soft solid polymers were below room temperature. The T_g of the solid poly(silyl ester) was not found below room temperature but a temperature for the transition in the liquid crystalline phase was found at 42°C. Thermal decomposition of the soft solid and solid poly(silyl ester)s started at about 130°C and for the others it started at about 200°C. The obtained hyperbranched polymers did not decompose completely at 700°C. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3430–3436, 2006     

Synthesis and characterization of silicon‐containing poly(amide‐amide)s

A modified new aromatic diacid, bis[(4‐carboxyphenyl) 4‐benzamide] dimethylsilane (IV) with preformed amide linkages and a silicon moiety was synthesized and characterized by IR, NMR, mass spectroscopy, and a physical constant. Novel poly(amide‐amide)s were synthesized from IV and aromatic diamines by Yamazaki's direct polyamidation method in N‐methyl pyrrolidinone. The polymers were obtained in excellent yields and showed reduced viscosities in the range of 0.42–6.15 dL/g. They were readily soluble in aprotic polar solvents. These poly(amide‐amide)s showed glass‐transition temperatures of 303–378°C as measured by DSC and showed no weight loss below 377°C in a nitrogen atmosphere. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1610–1617, 2001     

Effects of ion group content and polyol molecular weight on physical properties of HTPB‐based waterborne poly(urethane‐urea)s

A series of waterborne poly(urethane‐urea)s, WPUUs, based on using nonpolar hydroxyl‐terminated polybutadiene (HTPB) as the soft segment, were successfully synthesized in this article. The effects of the COOH group content and soft‐segment molecular weight (Mn_s) on the dispersion, morphology, and physical properties were investigated. Variations of the particle size, viscosity, and zeta potential were first governed by the hydrophilicity of the polymer chain, and then by the swelling derived from water. Fourier transfer infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) indicated that the degree of phase separation decreased as the COOH group content increased or as Mn_s decreased. However, the hydrogen bonding between the soft and hard segments and the two‐phase mixing could not occur in this nonpolar HTPB‐based WPUU system, indicating that the hard segments tended to form smaller domains and to pack more loosely. It was attributed to the fact that the presence of bulky ionic salt groups destroyed the ordered arrangement of the hard segments. In this case, the increases of the interface area between the soft and hard phases resulted in that the present behaviors were similar to the phase mixing. In tensile properties, HTPB‐based WPUUs exhibited higher tensile stress, elongation at break, and modulus as the COOH group content decreased or as Mn_s decreased. In thermal degradation, the introduction of HTPB polyol improved the thermal stability of WPUU. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Poly(imide‐amide)s and poly(imide‐ester)s obtained from N,N′‐(4,4′‐Me,R‐diphthaloyl)‐bis‐glycine acid dichloride (R = Me,Et): Synthesis,characterization, and thermal studies

Poly(imide‐amide)s (PIAs) and poly(imide‐ester)s (PIEs) containing two Si‐atoms in the repeating unit were synthesized from acid dichlorides and diamines and diphenols, respectively. The acid dichlorides were obtained from the dianhydrides, which reacted first with glycine and then with thionyl chloride. The dianhydrides were obtained from the tetramethyl derivatives, which were oxidized to the tetra acids and then the dianhydrides were obtained with acetic anhydride. PIAs were obtained in N,N‐dimethylacetamide solution at low temperature and the PIEs in a CHCl₃ solution. Monomers and polymers were characterized by IR and 1H, 13C, and 29Si‐NMR spectroscopy and the results were in agreement with the proposed structures. The η_inh values were indicative of low molecular weight species and of oligomeric nature. The glass transition (T_g) and thermal decomposition temperatures (TDT) values of PIAs were higher than those of PIEs due to the presence of the aromatic rings of the diamine. The aliphatic groups bonded to the Si atom of the acid dichloride moiety promoted the decrease of the thermal stability. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Hydrolytic resistance of model poly(ether urethane ureas) and poly(ester urethane ureas)

Poly(ester urethane ureas) (PesURUs) and poly(ether urethane ureas) (PetURUs) synthesized from diphenylmethane-4,4′-diisocyanate and poly(butylene adipate) diol, and poly(tetramethylene oxide) diol or poly(propylene oxide) diol, respectively, were hydrolyzed at 70°C for various periods up to 16 weeks. Differences in thermal and mechanical properties of as-received dry samples are correlated with the number and strength of hydrogen bonds formed between urea/urethane groups of hard segments and polyester or polyether groups of soft segments. Gel permeation chromatography measurements show that the molar mass of linear PesURUs markedly decreases with the hydrolysis time, whereas that of linear PetURUs remains almost unaffected. PesURU crosslinked by polymeric isocyanate has lower crystallinity, but shows somewhat better resistance to hydrolysis than its linear counterpart because of its more stable three-dimensional molecular structure. Water uptake at 37°C, dynamic mechanical thermal analysis, and differential scanning calorimetry thermograms determined for redried hydrolyzed specimens concurrently show that advancing hydrolysis accounts for decrease in the crystallinity (if any) of soft polyester segments, in the efficacy of hydrogen bonding and in crosslinking density. Experimental data indicate that hydrolytic resistance of PetURUs is primarily determined by (1) the hydrolytic stability of individual types of present groups, (2) steric hindrances affecting the access of water molecules to these groups, and (3) the hydrophilicity of backbones. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 577–586, 1998     

Synthesis and characterization of poly(urethane‐co‐imidine)s having pendent phenyl and benzylidene groups using bisphthalides,bislactones and blocked polyurethane prepolymers

Poly(urethane‐co‐imidine)s were prepared using amine blocked polyurethane (PU) prepolymer. The PU prepolymer was prepared by the reaction of poly(propylene glycol) (PPG₂₀₀₀) and 2,4‐tolylene diisocyanate (TDI) and end capped with N‐methyl aniline. The PU prepolymer was then reacted with bisphthalides and bislactones, until the evolution of carbon dioxide ceased. Polymerization reactions with bispthalides and bislactone took more time than with dianhydrides. Polymers were characterized by FTIR, GPC, TG and DSC analyses. Molecular weights of the poly(urethane‐co‐imidine)s were found to be lower than that of poly(urethane‐co‐imide)s. Compared to poly(urethane‐co‐imide)s all poly(urethane‐co‐imidine)s showed high glass transition temperature and crystallization peak in DSC. The thermal stability of the polyurethanes was found to increase with the introduction of imidine component. © 2001 Society of Chemical Industry     

Synthesis of poly(urethane)s based on diphenyl‐silane/germane and oxyphenyl units: Structure–properties relationship

A series of poly(urethane)s (PUs) based on diphenyl‐silane or ‐germane and oxyphenyl units were synthesized by polycondesation of 4‐[4‐[9‐[4‐(4‐aminophenoxy)‐3‐methyl‐phenyl]fluoren‐9‐yl]‐2‐methyl‐phenoxy]aniline (3) and four bis(chloroformate)s ( I–IV ). These monomers were prepared and characterized in previous works. The best conditions for the polymerization reactions were investigated by a kinetic study. Also, a selection of the best solvent for the reaction was developed. Polymers were characterized by IR and ¹H, ¹³C, and ²⁹Si‐NMR spectroscopy and the results were in agreement with the proposed structures. Poly(urethane)s showed inherent viscosity values between 0.12 and 0.31 dL/g, indicative of low molecular weight species, probably of oligomeric nature. The glass transition temperature (T_g) values were observed in the 127–168°C range by DSC analysis. Thermal decomposition temperature (TDT_10%) values were above 300°C. All PUs showed good transparency in the visible region (>80% at 350 nm) due to the incorporation of the bulky monomer (fluorene) and oxyether linkages. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis,characterization and properties of biodegradable poly(butylene succinate)‐block‐poly(propylene glycol) segmented copolyesters

BACKGROUND: To obtain a biodegradable thermoplastic elastomer, a series of poly(ester‐ether)s based on poly(butylene succinate) (PBS) and poly(propylene glycol) (PPG), with various mass fractions and molecular weights of PPG, were synthesized through melt polycondensation. RESULTS: The copolyesters were characterized using ¹H NMR, gel permeation chromatography, differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical analysis, mechanical testing and enzymatic degradation. The results indicated that poly(ester‐ether)s with high molecular weights were successfully synthesized. The composition of the copolyesters agreed very well with the feed ratio. With increasing content of the soft PPG segment, the glass transition temperature decreased gradually while the melting temperature, the crystallization temperature and the relative degree of crystallinity decreased. Mechanical testing demonstrated that the toughness of PBS was improved significantly. The elongation at break of the copolyesters was 2–5 times that of the original PBS. Most of the poly(ester‐ether) specimens were so flexible that they were not broken in Izod impact experiments. At the same time, the enzymatic degradation rate of PBS was enhanced. Also, the difference in molecular weight of PPG led to properties being changed to some extent among the copolyesters. CONCLUSION: The synthesized poly(ester‐ether)s having excellent flexibility and biodegradability extend the application of PBS into the areas where biodegradable thermoplastic elastomers are needed. Copyright © 2009 Society of Chemical Industry     

Synthesis of biodegradable amino‐acid‐based poly(ester amide)s and poly(ether ester amide)s with pendant functional groups

A new family of biodegradable amino‐acid‐based poly(ester amide)s (AA–PEAs) and amino‐acid‐based poly(ether ester amide)s (AA–PEEAs) consisting of reactive pendant functional groups (? COOH or ? NH₂) were synthesized from unsaturated AA–PEAs and AA–PEEAs via a thiol–ene reaction in the presence of a radical initiator (2,2′‐azobisisobutyronitrile). The synthetic method was a one‐step reaction with near 100% yields under mild reaction conditions. The resulting functional AA–PEA and AA–PEEA polymers were characterized by Fourier transform infrared spectroscopy, NMR, and differential scanning calorimetry. These new functional AA–PEA and AA–PEEA derivatives had lower glass‐transition temperatures than the original unsaturated AA–PEA and AA–PEEA polymers, and their solubility in some organic solvents also improved. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of poly(ester ether siloxane)s

A series of novel thermoplastic elastomers based on ABA‐type triblock prepolymers, poly[(propylene oxide)–(dimethylsiloxane)–(propylene oxide)] (PPO‐PDMS‐PPO), as the soft segments, and poly(butylene terephthalate) (PBT), as the hard segments, was synthesized by catalyzed two‐step melt transesterification of dimethyl terephthalate (DMT) with 1,4‐butanediol (BD) and α,ω‐dihydroxy‐(PPO‐PDMS‐PPO) (M?_n = 2930 g mol^?1). Several copolymers with a content of hard PBT segments between 40 and 60 mass% and a constant length of the soft PPO‐PDMS‐PPO segments were prepared. The siloxane‐containing triblock prepolymer with hydrophilic terminal PPO blocks was used to improve the compatibility between the polar comonomers, i.e. DMT and BD, and the non‐polar PDMS segments. The structure and composition of the copolymers were examined using ¹H NMR spectroscopy, while the effectiveness of the incorporation of α,ω‐dihydroxy‐(PPO‐PDMS‐PPO) prepolymer into the copolyester chains was controlled by chloroform extraction. The effect of the structure and composition of the copolymers on the transition temperatures (T_m and T_g) and the thermal and thermo‐oxidative degradation stability, as well as on the degree of crystallinity, and some rheological properties, were studied. Copyright © 2006 Society of Chemical Industry