Rheological characterization of HDPE/sisal fiber composites

The present paper summarizes an experimental study on the molten viscoelastic behavior of HDPE/sisal composites under steady and dynamic mode. Variations of the melt viscosity and die swell of the composites with an increase in shear rate, fiber loading, and coupling agent concentration have been investigated using capillary rheometer. The shear rate γ at the wall was calculated using Rabinowitsch correction applied to the apparent shear rate values. It was observed that the melt viscosity of the composites increased with the addition of fibers and maleic anhydride-grafted PE (MAPE). Die swell of HDPE also decreased with the addition of sisal fibers and MAPE. Further, the dynamic viscoelastic behavior of the composites was measured employing parallel plate rheometer. Time–temperature superposition was applied to generate various viscoelastic master curves. Temperature sweeps were also carried out to study the flow activation energy determined from Arrhenius equation. The fiber–matrix morphology of the extrudates was also examined using scanning electron microscopy. POLYM. ENG. SCI., 47:1634–1642, 2007. © 2007 Society of Plastics Engineers     

The influence of matrix viscosity on properties of polypropylene/polyaniline composite fibers—Rheological,electrical, and mechanical characteristics

Electrically conductive composites containing polypropylene (PP) and polyaniline (PANI) were prepared using PP with three different melt flow rates (MFRs) and a commercial PANI‐complex in proportions of 80% by weight and 20%, respectively. Composite blends were melt‐spun to fibers under different solid‐state draw ratios. Rheological studies of dynamic viscosity, as well as the storage modulus and loss modulus showed that the prepared PANI‐complex/PP blends exhibit different dynamic rheological behavior, depending on the PP used. This confirms the blends' morphological differences. PP matrix viscosity was found to play an important role in the electrical properties of the prepared fibers. Fibers prepared using the matrix with the lowest viscosity, showed a larger dispersed phase size in the cross‐sectional SEM micrographs, maximum conductivity observed at higher draw ratios and a more linear resistance–voltage relationship than those of the fibers prepared using the higher viscosity matrices. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Melt rheological behavior of intimately mixed short sisal–glass hybrid fiber‐reinforced low‐density polyethylene composites. I. Untreated fibers

The melt rheological behavior of intimately mixed short sisal–glass hybrid fiber‐reinforced low‐density polyethylene composites was studied with an Instron capillary rheometer. The variation of melt viscosity with shear rate and shear stress at different temperatures was studied. The effect of relative composition of component fibers on the overall rheological behavior also was examined. A temperature range of 130 to 150°C and shear rate of 16.4 to 5470 s^?1 were chosen for the analysis. The melt viscosity of the hybrid composite increased with increase in the volume fraction of glass fibers and reached a maximum for the composite containing glass fiber alone. Also, experimental viscosity values of hybrid composites were in good agreement with the theoretical values calculated using the additive rule of hybrid mixtures, except at low volume fractions of glass fibers. Master curves were plotted by superpositioning shear stress and temperature results. The breakage of fibers during the extrusion process, estimated by optical microscopy, was higher for glass fiber than sisal fiber. The surface morphology of the extrudates was analyzed by optical and scanning electron microscopy. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 432–442, 2003     

Melt rheological behavior of intimately mixed short sisal–glass hybrid fiber‐reinforced low‐density polyethylene composites. II. Chemical modification

The effect of chemical modification of both fiber and matrix on melt rheological behavior of intimately mixed short sisal–glass hybrid fiber‐reinforced low‐density polyethylene composites was studied with an Instron capillary rheometer. The variations of melt viscosity with different shear rate and shear stress values for different temperatures were studied. A temperature range of 130 to 150°C and shear rates of 16.4 to 5468 s^?1 were chosen for the analysis. Chemical modifications with stearic acid, maleic anhydride, silane, and peroxides were tested for their ability to improve the interaction between the matrix and fiber. The viscosity of the hybrid composites increases with every chemical modification. In the case of peroxide‐treated composites, the increase can be attributed to the peroxide‐induced grafting of the polyethylene matrix to the fiber surface and to the crosslinking of the polyethylene matrix. These phenomena are both activated by temperature, whereas temperature causes a reverse effect for all other chemical modifications. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 443–450, 2003     

Impact toughness,viscoelastic behavior,and morphology of polypropylene–jute–viscose hybrid composites

In this investigation, we studied the impact toughness and viscoelastic behavior of polypropylene (PP)–jute composites. In this study, we used viscose fiber as an impact modifier and maleated PP as a compatibilizer. The toughness of the composites was studied with conventional Charpy and instrumental falling‐weight impact tests. The composites’ viscoelastic properties were studied with dynamic mechanical analysis. The results show that the incorporation of viscose fibers improved the impact strength and toughness to 134 and 65% compared to those of the PP–jute composites. The tan δ peak amplitude also increased with the addition of the impact modifier and indicated a greater degree of molecular mobility. The thermal stability of the composites was evaluated with thermogravimetric analysis. The addition of 2 wt % maleated polypropylene (MAPP) to the impact‐modified composite improved the impact strength and toughness to 144 and 93%, respectively. The fiber–matrix morphology of the fracture surface and the Fourier transform infrared spectra were also studied to ascertain the existence of the type of interfacial bonds. Microstructural analysis showed the retention of viscose fibers in the composites compared to the more separated jute fibers. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42981.     

Effect of wood fibers on the rheological properties of i‐PP/wood fiber composites

The effects of wood fibers on the melt rheological behavior of isotactic poly(propylene) (i‐PP)/wood fiber (WF) composites have been studied at WF concentrations of 0–32.2 vol % at 493 K. Shear stress–shear rate variations obeyed a power law equation, and the composites exhibited shear thinning, which increased with filler content. At a low shear rate, the apparent melt viscosity increased, while melt elasticity, after an initial decrease, also increased with WF concentration. At a higher shear rate, after an initial decrease, the melt viscosity showed an increase, as did melt elasticity, with increase in filler content. A titanate coupling agent, LICA 38, used to modify the wood fiber surface, modified these rheological parameters by functioning as a plasticizer/lubricant. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 644–650, 2004     

Studies on thermal,mechanical, morphological,and viscoelastic properties of polybenzimidazole fiber reinforced high density polyethylene composites

High density polyethylene (HDPE) and polybenzimidazole fiber (PBI) composites were prepared by melt blending in a twin screw extruder. The thermomechanical properties of PBI fiber reinforced HDPE composite samples (1%, 4%, and 8%) of fiber lengths 3 mm and 6 mm were investigated using differential scanning calorimeter (DSC), universal testing machine, rheometer, and scanning electron microscopy (SEM). The effects of fiber content and fiber lengths on the thermomechanical properties of the HDPE‐PBI composites were studied. The DSC analysis showed a decrease in crystallinity of HDPE‐PBI composites with an increase of fiber loading. SEM images revealed homogeneous distribution of the fibers in the polymer matrix. The thermal behavior of the composites was evaluated from thermogravimetric analysis and the thermal stability was found to increase with the addition of fibers. The evidence of homogeneous distribution was verified by the considerably high values of tensile strength and flexural strength. In the rheology study, the complex viscosities of HDPE‐PBI composites were higher than the HDPE matrix and increased with the increasing of PBI fiber loading. POLYM. COMPOS., 5–13, 2016. © 2014 Society of Plastics Engineers     

Rheological analysis of vapor‐grown carbon nanofiber‐reinforced polyethylene composites

The melt rheological analysis of high‐density polyethylene reinforced with vapor‐grown carbon nanofibers (VGCNFs) was performed on an oscillatory rheometer. The influence of frequency, temperature, and nanofiber concentration (up to 30 wt %) on the rheological properties of composites was investigated. Specifically, the viscosity increase is accompanied by an increase in the elastic melt properties, represented by the storage modulus G′, which is much higher than the increase in the loss modulus G″. The composites and pure PE exhibit a typical shear thinning behavior as complex viscosity decreases rapidly with the increase of shearing frequency. The shear thinning behavior is much more pronounced for the composites with high fiber concentration. The rheological threshold value for this system was found to be around 10 wt % of VGCNF. The damping factor was reduced significantly by the inclusion of nanofibers into the matrix. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 155–162, 2004     

Investigation of rheology and morphology to follow physical fibrillar network evolution through fiber spinning of PP/PA6 blend fiber

This work is aimed at investigating the influence of fibrillar morphology of deformed Polyamide 6 (PA6) droplets dispersed in Polypropylene (PP) matrix on the melt viscoelastic behavior of their blends. The blends of PP with various amounts of PA6 (1%, 6%, 10%, and 20%) were prepared by melt mixing in a co‐rotating twin screw extruder and fibrillated by fiber spinning process. Scanning Electron Microscopy revealed that the PA6 spherical droplets form fibrillar inclusions after fiber spinning. The steady and transient shear rheological responses of samples were evaluated in both linear and nonlinear ranges of deformation. Non‐terminal behavior of storage modulus at low frequency appeared as a typical characteristic of fibrillar morphology whose width and value depend on fibril growth. Storage modulus and complex viscosity of the blends containing PA6 fibrillated structure were remarkably enhanced compared to as‐extruded samples. The fibrillar‐induced elasticity of the fibers is a distinguishable behavior which was revealed by conducting transient stress and creep‐recovery measurements and upon appearing mature fibrils, elasticity of the polymer blend fibers increased significantly. POLYM. ENG. SCI., 58:1251–1260, 2018. © 2017 Society of Plastics Engineers     

热氧老化对长玻璃纤维增强PP材料动态流变性能影响

通过熔融共混法制备长玻璃纤维增强聚丙烯(LGFPP)复合材料,采用旋转流变仪和扫描电子显微镜测试研究了不同热氧老化时间下复合材料的动态流变行为。结果表明,热氧老化过程PP发生降解,分子量降低,同时随老化程度的加深分子链的缠结以及分子间相互作用力逐渐被削弱,分子链松弛能力增加;树脂的降解过程容易在纤维与基体的界面区域进行,使得纤维与基体的界面性能下降,粘结力下降。因此,随老化时间的增加复合材料的储能模量、损耗模量、损耗因子以及复数黏度都呈现下降趋势。     

Online measurement of rheological properties of PVC/wood‐flour composites

By using a factorial design approach, this study examined the effect of the component materials on the viscoelastic properties of PVC/wood‐flour composites. Statistical analysis was performed to determine the effects of wood‐flour content, acrylic modifier content, and plasticizer content on the die swell ratio and viscosity of the composites measured online on a conical twin‐screw extrusion capillary rheometer. The viscoelastic properties of the samples also were measured using dynamic mechanical analyzer (DMA). Wood‐flour content and acrylic modifier content were the two important variables affecting the die swell ratio, whereas the addition of a low level of plasticizer did not affect this ratio. The die swell increased with the increased acrylic modifier content, but it was reduced considerably by adding wood flour into the PVC matrix. The true viscosity of neat PVC and PVC/wood‐flour composites decreased with the plasticizer content, irrespective of the acrylic modifier content. However, the addition of acrylic modifier significantly increased the viscosity of unfilled PVC, while an opposite trend was observed for the composites, owing to the differing effect of acrylic modifier on the melt elasticity and viscosity of these materials. J. Vinyl Addit. Technol. 10:121–128, 2004. © 2004 Society of Plastics Engineers.     

Performance of long glass fiber‐reinforced polypropylene composites at different injection temperature

Long glass fiber‐reinforced polypropylene composites were prepared using self‐designed impregnation device. Effects of the different injection temperature on mechanical properties, crystallization, thermal, and dynamic mechanical properties of long glass fiber‐reinforced polypropylene composites were discussed. The differential scanning calorimetry (DSC) results indicate that the melting peak temperature of PP/LGF composites gradually reduced, however, the crystallinity of PP/LGF composites gradually increased with increasing injection temperature. Thermo‐gravimetric analyzer (TGA) results demonstrate that with increasing injection temperature, the temperature of the PP/LGF composites melt increased, the viscosity of the PP/LGF composites melt lowered, the mold filling of the PP/LGF composites melt was easy, the shear force of glass fiber was relatively low, which made the residual length of glass fiber in products increase. Dynamic thermal mechanical analyzer (DMA) results show that the storage modulus of PP/LGF composites is the highest while the injection temperature is at 290°C, and the peak value of tan σ of PP /LGF composites at 290°C is minimal, which indicates that the mechanical properties of PP /LGF composites at 290°C is the best. What' more, the injection temperature at 290°C significantly ameliorated “glass fiber rich skin” of products of glass fiber‐reinforced composites. J. VINYL ADDIT. TECHNOL., 24:233–238, 2018. © 2016 Society of Plastics Engineers     

Polymerization compounding composites of nylon‐6,6/short glass fiber

Nylon‐6,6 was grafted onto the surface of short glass fibers through the sequential reaction of adipoyl chloride and hexamethylenediamine onto the fiber surface. Grafted and unsized short glass fibers (USGF) were used to prepare composites with nylon‐6,6 via melt blending. The glass fibers were found to act as nucleating agents for the nylon‐6,6 matrix. Grafted glass fiber composites have higher crystallization temperatures than USGF composites, indicating that grafted nylon‐6,6 molecules further increase crystallization rate of composites. Grafted glass fiber composites were also found to have higher tensile strength, tensile modulus, dynamic storage modulus, and melt viscosity than USGF composites. Property enhancement is attributed to improved wetting and interactions between the nylon‐6,6 matrix and the modified surface of glass fibers, which is supported by scanning electron microscopy (SEM) analysis. The glass transition (tan δ) temperatures extracted from dynamic mechanical analysis (DMA) are found to be unchanged for USGF, while in the case of grafted glass fiber, tan δ increases with increasing glass fiber contents. Moreover, the peak values (i.e., intensity) of tan δ are slightly lower for grafted glass fiber composites than for USGF composites, further indicating improved interactions between the grafted glass fibers and nylon‐6,6 matrix. The Halpin‐Tsai and modified Kelly‐Tyson models were used to predict the tensile modulus and tensile strength, respectively.     

The effect of fiber concentration on mechanical and thermal properties of fiber‐reinforced polypropylene composites

A novel composite material consisting of polypropylene (PP) fibers in a random poly(propylene‐co‐ethylene) (PPE) matrix was prepared and its properties were evaluated. The thermal and mechanical properties of PP–PPE composites were studied by dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) with reference to the fiber concentration. Although, by increasing PP fiber concentration in PPE, no significant difference was found in melting and crystallization temperatures of the PPE, the storage, and the tensile and flexural modulus of the composites increased linearly with fiber concentrations up to 50%, 1.5, 1.0, 1.3 GPa, respectively, which was approximately four times higher than that for the pure PPE. There is a shift in glass transition temperature of the composite with increasing fiber concentration in the composite and the damping peak became flatter, which indicates the effectiveness of fiber–matrix interaction. A higher concentration of long fibers (>50% w/w) resulted in fiber packing problems, difficulty in dispersion, and an increase in void content, which led to a reduction in modulus. Cox–Krenchel and Haplin–Tsai equations were used to predict tensile modulus of random fiber‐reinforced composites. A Cole–Cole analysis was performed to understand the phase behavior of the composites. A master curve was constructed based on time–temperature superposition (TTS) by using data over the temperature range from −50 to 90°C, which allowed for the prediction of very long and short time behavior of the composite. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2260–2272, 2005     

Investigating polypropylene–green coconut fiber composites in the molten and solid states through various techniques

A series of polypropylene (PP)–green coconut fiber (GCF) composites were prepared by melt mixing and their properties studied in the molten state using an advanced nonlinear harmonic testing technique, and in the solid state using standard mechanical testing and scanning electron microscopy (SEM). The effect of fiber loading as well as the role of maleated polypropylene as compatibilizing agent was investigated. PP–GCF composites are heterogeneous materials that, in the molten state, are found to exhibit essentially a nonlinear viscoelastic character, in contrast with the pure PP, which has a linear viscoelastic region up to 50–60% strain. Complex modulus increases with GCF content but in such a manner that the observed reinforcement is at best of hydrodynamic origin, without any specific chemical interaction occurring between the polymer matrix and the fibers. The addition of maleated polypropylene improves the wetting of fibers by the molten polymer but the effect is so small that specific chemical reactions could hardly be considered as occurring. Flexural modulus data confirm the reinforcing effects of the fiber and an improvement is noted when some maleated polypropylene is used, with an optimum level of around 1% (or the PP content). SEM microphotographs clearly show that maleated polypropylene imparts a better wetting of GC fibers by PP, but chemical interactions are unlikely to occur between the polymer and GCF. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1922–1936, 2006     

Studies on preparation of immersion‐type polypropylene fragrant fiber. I. Formation of matrix fiber in the melt‐spinning process and its technique of immersion essential oil

Polypropylene/ethylene vinyl acetate (PP/EVA) blends were prepared in a plastic extruder with a static mixer. The thermodynamic compatibility, morphology, crystal form, and rheological behavior of PP/EVA blends were investigated by SEM, DSC, and rheology instruments. The results showed that PP and EVA were thermodynamically incompatible, the viscosity of the PP/EVA blends decreased with increase of shear rate in a range of temperature, the PP/EVA blends had a sea‐islands structure, and the crystalline zones remained in their original state and could not form mixed crystals in the PP/EVA blends. The PP/EVA blends were melt spun to prepare matrix fibers and the spinning conditions such as EVA content, the matching factor between pump delivery and winding velocity, and the melt‐spinning temperature were also determined. The sorption process of a matrix fiber for essential oils, adsorbed under various sorption conditions such as sorption time, sorption temperature, and EVA content, was also studied. The results revealed that the composite isotherm of the adsorption of matrix fiber for essential oil was characteristic of a U model. Through adsorbing essential oil, the immersion‐type PP fragrant fibers could be prepared with the matrix fiber. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1970–1979, 2003     

硫磺改性聚丙烯纤维材料及其流变行为的研究

采用熔融接枝法制备了相容剂硫磺接枝聚丙烯(PP-g-S),同时制备了不同硫磺(S)含量的聚丙烯(PP)/PP-g-S/S改性纤维材料。分别用哈克转矩流变仪、红外光谱仪、核磁共振仪、熔体流动速率仪、扫描电子显微镜对接枝相容剂进行对比分析,再用旋转平板流变仪研究了S含量对PP/PP-g-S/S改性纤维材料的动态流变行为的影响。结果表明,在过氧化二异丙苯的引发下可以通过熔融接枝法制得相容剂PP-g-S,而且相容剂PP-g-S对PP/PP-g-S/S改性纤维材料起到了明显的增容作用;随着S含量的增加,PP/PP-g-S/S改性纤维材料的复数黏度、储能模量、损耗模量及损耗因子均增大,Cole-Cole曲线圆弧半径增大,零剪切黏度增大、S呈均相均匀分散。     

Effect of alkali‐resistant glass fiber on polypropylene/polystyrene blends: Modeling and characterization

Alkali‐resistant glass fiber (GF) reinforced polypropylene (PP)/polystyrene (PS) blends were prepared by melt mixing in a Thermo Haake Rheochord mixer. Variation in thermal and mechanical properties with the addition of glass fibers into the polypropylene/polystyrene blends was investigated. The characterization of PP/PS/GF composites was done by dynamic mechanical analysis (DMA), thermogravimetric analysis, scanning electron microscope, and transmission electron microscope. The experimentally observed tensile properties of glass fiber reinforced PP/PS blends were compared with various published models. It was found that the experimental results agree well with Hui‐ Shia and series models. DMA tests revealed an increase in storage modulus with fiber loading confirms the greater degree of stress transfer from the matrix to the fiber. TEM micrographs reveal that the glass fibers are located at the interface between the blend components. POLYM. COMPOS., 37:398–406, 2016. © 2014 Society of Plastics Engineers     

Dynamic rheological behavior of polypropylene melts with pulsatile pressure flow in a dynamic capillary rheometer

A self‐made dynamic capillary rheometer (DCR) was designed to investigate the dynamic viscoelastic characteristic of polypropylene (PP) melt during the pulsatile pressure extrusion. A vibration force field was parallel superposed upon steady shear flow in this DCR by means of a vibration driven piston. During the pulsatile pressure extruding process in DCR, the PP melt displayed apparent viscoelasticity. The experiment results proved the pressure pulsatile extrusion could reduce the viscosity of polymer melts effectively. The phase difference between the shear stress and the shear rate decreased with the superposed vibration. But, at large amplitude conditions, the viscosity has an increasing tendency. This maybe illuminated that large amplitude could be harmful for the vibration‐assistant polymer processing. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1834–1838, 2006     

Structural properties and mechanical behavior of injection molded composites of polypropylene and sisal fiber

Composites based on isotactic polypropylene (PP) and sisal fiber (SF) were prepared by melt mixing and injection molding. The melt mixing characteristics, thermal properties, morphology, crystalline structure, and mechanical behavior of the PP/SF composites were systematically investigated. The results show that the PP/SF composites can be melt mixed and injection molded under similar conditions as the PP homo‐polymer. For the composites with low sisal fiber content, the fibers act as sites for the nucleation of PP spherulites, and accelerate the crystallization rate and enhance the degree of crystallinity of PP. On the other hand, when the sisal fiber content is high, the fibers hinder the molecular chain motion of PP, and retard the crystallization. The inclusion of sisal fiber induces the formation of β‐form PP crystals in the PP/SF composites and produces little change in the inter‐planar spacing corresponding to the various diffraction peaks of PP. The apparent crystal size as indicated by the several diffraction peaks such as L_(110)α, L_(040)α, L_(130)α and L_(300)β of the α and β‐form crystals tend to increase in the PP/SF composites considerably. These results lead to the increase in the melting temperature of PP. Moreover, the stiffness of the PP/SF composites is improved by the addition of sisal fibers, but their tensile strength decreases because of the poor interfacial bonding. The PP/SF composites are toughened by the sisal fibers due to the formation of β‐form PP crystals and the pull‐out of sisal fibers from the PP matrix, both factors retard crack growth.