The reaction in water of UF resins with isocyanates at short curing times: A 13C NMR investigation

CP MAS ¹³C NMR spectra of hardened resins have shown that urethane bridges derived from the reaction of the isocyanate group with the hydroxymethyl group of urea do form even at fast curing times comparable to what was used in the wood panels industry, in lower proportions than what was shown earlier. Polyureas and biurets obtained from the reaction of isocyanate with water are the predominant crosslinking reactions of pMDI alone and in UF/pMDI resin systems under fast curing conditions. Residual, unreacted isocyanate groups in the hardened network are consistently observed. Their proportion markedly decreases when the original proportion of urea–formaldehyde (UF) resin is high and that of pMDI is low. Under these fast curing conditions, the UF resin appears to self‐condense through an unusually high proportion of methylene ether links rather than methylene bridges alone. A marked proportion of residual, unreacted hydroxymethyl groups is also noticeable, initially, in the UF self‐condensation network. Direct NMR tests on thin hardboard bonded under fast pressing conditions with different proportions of UF/pMDI confirmed that crosslinking due to polyureas and biurets formation are predominant in the crosslinking of pMDI when alone and in UF/pMDI resin systems. They confirmed that residual, unreacted isocyanate groups are present in the finished panel. Their proportion is higher when the proportion of pMDI in the system is high. The presence or absence of urethanes could not be confirmed directly on the panels as the relevant peaks are masked by the wood carbohydrates signals of wood cellulose and hemicelluloses. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1624–1632, 2006     

Copolymerization in UF/pMDI adhesives networks

Kinetic evidence in thermomechanical analysis experiments and carbon‐13 nuclear magnetic resonance spectroscopy (¹³C NMR) evidence indicates that the strength of a joint bonded with UF (urea–formaldehyde)/polymeric 4,4'‐diphenylmethane diisocyanate (pMDI) glue mixes is improved by coreaction of the methylol groups of UF resins with pMDI to form a certain number of methylene cross‐links. The formation of these methylene cross‐links is predominant, rather than formation of urethane bridges which still appear to form but which are in great minority. This reaction occurs in presence of water and under the predominantly acid hardening conditions, which is characteristic of aminoplastic resins (thus, in presence of a hardener). Coreaction occurs to a much lesser extent under alkaline conditions (hence, without UF resins hardeners). The predominant reaction is then different in UF/pMDI adhesive systems than that observed in phenol‐formaldehyde (PF)/pMDI adhesive systems. The same reaction observed for UF/pMDI system at higher temperatures has also been observed in PF/pMDI systems, but only at lower temperatures. The water introduced in the UF/pMDI mix by addition of the UF resin solution has been shown not to react with pMDI to an extent such as to contribute much, if at all, to the increase in strength of the hardened adhesive. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3681–3688, 2002     

Study of hybrid isocyanate and high-mono-hydroxymethyl urea content urea-formaldehyde resins

Based on the difference in the reaction rate of different groups of urea-formaldehyde resins and isocyanate resins, this study designed two different urea-formaldehyde resins: a normal urea-formaldehyde resin (UF) and one with high mono-hydroxymethylurea content (UF*) to react with polymeric methylene diphenyl diisocyanate (pMDI) resin. The difference in mono- and di-hydroxymethyl urea content between UF and UF* resins was analyzed by nuclear magnetic resonance (NMR) spectroscopy, and results showed that the mono-hydroxymethyl urea content of the UF* resin was much higher than that of the conventional UF resin. The fourier transform infrared spectrometer (FTIR) analysis of differences between UF* and UF resin showed that the UF* process did not change the main structure of the conventional urea formaldehyde resin. Differential scanning calorimeter (DSC) analysis showed that the curing temperature of the hybrid UF*-pMDI resin was reduced 27.3°C compared to that of the UF-pMDI resin. When these hybrid resins were used to bond plywood respectively, test results showed that the UF*-pMDI resin improved the dry and wet bonding strength by 2.6% and 3.9%, respectively, compared with the UF-pMDI resin under the condition of hot pressing time (3 min) and temperature (140°C), meeting the requirement of Chinese standard of GB/T 9846–2015 for Class III board. This study provides a new path for further improving the performance and design of hybrid resins based on isocyanate and urea-formaldehyde resin.     

Modification of urea-formaldehyde resin adhesives with blocked isocyanates using sodium bisulfite

Polymeric 4-4 diphenyl methane diisocyanate (pMDI) was blocked with an aqueous sodium bisulfite solution to obtain water-dispersible blocked pMDI (B-pMDI) resin with different HSO₃/–NCO mole ratios for the modification of urea-formaldehyde (UF) resin. Fourier transform infrared (FTIR) spectra of the B-pMDI resin clearly showed that all isocyanate groups of the pMDI resin were successfully blocked by sodium bisulfite. As the HSO₃/–NCO mole ratio increased, the de-blocking temperature of the B-pMDI resin also increased. Two addition levels (1% and 3%) of the B-pMDI resin with different HSO₃/–NCO mole ratios were mixed with UF resins and used as an adhesive for plywood. The gel time of the UF/B-pMDI resins decreased to a minimum at a mole ratio of 0.9 and then increased with the HSO₃/–NCO mole ratio, and was consistent with the peak temperature (Tp). However, as the HSO₃/–NCO mole ratio increased, the viscosity of the modified UF resins by 1% B-pMDI resin addition slightly increased, whereas those of modified resins with 3% B-pMDI resin addition rapidly increased. The adhesion strengths of plywood bonded with the hybrid resins were greater for 1% B-pMDI resin addition than for 3% B-pMDI resin addition. Formaldehyde emission of plywood bonded with the UF/B-pMDI resins significantly decreased up to 34% by the addition of B-pMDI resin at a mole ratio of 1.8. These results suggest that the modification of UF resins by mixing with water-dispersible B-pMDI resin can be a method for improving the water resistance and formaldehyde emission of UF resins for wood-based composites.     

Improving the properties of ionic liquid-treated lignin-urea-formaldehyde resins by a small addition of isocyanate for wood adhesive

The aim of this research was to investigate the effect of polymeric 4, 4 diphenyl methane diisocyanate (pMDI) on the physical and mechanical properties of plywood panels bonded with an ionic liquid (IL)-treated lignin-urea-formaldehyde resin. Soda lignin modified by 1-ethyl-3-methylimidazolium acetate ([Emim][OAc]) IL was added to a urea formaldehyde (UF) resin during resin synthesis to prepare a lignin-urea-formaldehyde (LUF) resin. pMDI at various contents (2, 4, and 6% on resin solids) was then added to prepare a LUF resin. The thermal and physicochemical properties of the resins prepared as well as the water absorption, shear strength, and formaldehyde emission of the plywood panels bonded with them were measured according to standard methods. DSC analysis indicated that the addition of pMDI decreases the gel onset and curing temperatures of the LUF resin. According to the results obtained, the addition of pMDI significantly increased the viscosity and solid content and accelerated the gelation time of LUF resins. Based on the findings of this research, the addition of pMDI dramatically improves the performance of LUF resins as a new adhesive for wood-based panels. The LUF resins with isocyanate added yielded panels presenting lower formaldehyde emission and lower water absorption content when compared to those bonded with the control LUF resins. Greater dry and wet shear strength can be obtained by a small addition of pMDI to LUF resins.     

Synthesis–structure–performance relationship of cocondensed phenol–urea–formaldehyde resins by MALDI‐ToF and 13C NMR

Matrix assisted laser desorption ionization time of flight (MALDI‐ToF) mass spectrometry has consistently confirmed on a number of PUF resins that phenol–urea cocondensates exist in phenol–urea–formaldehyde (PUF) resins. A noticeable proportion of methylene‐linked phenol to urea cocondensates were detected in all the PUF resins tried, alongside methylene bridges connecting phenol to phenol and urea to urea. The PUF, PF, and UF oligomers formed were identified. Variations of the PUF preparation procedure did always yield a certain proportion of the mixed phenol to urea cocondensates. Their relative proportion was determined and related the synthesis procedure used. Comparison of the MALDI‐ToF results with a ¹³C NMR investigation showed that in a real PUF resin in which phenol to urea cocondensates were identified the methylene bridge NMR signal at 44 ppm, characteristic of phenol to urea unsubstituted model compound cocondensates, does not appear at all. This confirmed that this peak cannot be taken as an indication of the existence of phenol and urea condensation under actual resin preparation conditions. The peak indicating cocondensation in PUF resins in which the phenolic nuclei and urea are substituted appears instead at 54.7–55.0 ppm. Thermomechanical analysis has again confirmed that the resin gel times greatly accelerates with increasing urea molar content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Comparative 13C‐NMR and matrix‐assisted laser desorption/ionization time‐of‐flight analyses of species variation and structure maintenance during melamine–urea–formaldehyde resin preparation

The preparation of an industrially used sequential formulation of a melamine–urea–formaldehyde resin was followed by matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry and ¹³C‐NMR analysis. The analysis allowed us to identify and follow the appearance, increase, decrease, and disappearance of a multitude of chemical species during the preparation of both the initial urea–formaldehyde (UF) phase of the reaction and the subsequent reaction of melamine with the UF resin that formed. The analysis indicated that (1) the increase and decrease in the species that formed proceeded through a cycle of the formation and degradation of species occurring continuously through what appeared to be a series of complex equilibria, (2) even at the end of the reaction a predominant proportion of methylene ether bridges was still present, (3) some small proportion of methylene bridges already had formed in the UF reaction phase of the resin even under rather alkaline conditions, and (4) the addition of melamine to the UF prepolymer induced some noticeable rearrangement of methylene ether bridges to methylene bridges. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

15N CP/MAS NMR Study of the Isocyanate/Wood Adhesive Bondline. Effects of Structural Isomerism

Structurally isomeric ¹⁵N-labeled polymeric methylenebis(phenylisocyanate), pMDI, adhesives were synthesized. One resin had a high content of 4,4'-MDI, and another was prepared with a high content of 2,4'-MDI. Both resins were cured with wood (Liriodendron tulipifera) for various times and temperatures and then analyzed using ¹⁵N CP/MAS NMR. It was found that resin polymerization occurs via the reaction of isocyanate with wood moisture to form polyurea. Biuret formation and isocyanate dimerization were detected. Urethane formation probably also occurs; however, signal overlap of urea and urethane signals prevents a definitive conclusion. These findings are similar to previous ones; however, subtle differences are noted. The structurally isomeric resins displayed similar chemistries. Of the two resins, the resin prepared with a high content of 2,4'-MDI cured more slowly, and resulted in a network that was more mobile in the midkilohertz frequency range. This leads to the prediction that resins high in 2,4'-MDI may have a superior performance in impact loading.     

Hydrolytic stability of cured urea‐formaldehyde resins modified by additives

Urea‐formaldehyde (UF) resins are prone to hydrolysis that results in low‐moisture resistance and subsequent formaldehyde emission from UF resin‐bonded wood panels. This study was conducted to investigate hydrolytic stability of modified UF resins as a way of lowering the formaldehyde emission of cured UF resin. Neat UF resins with three different formaldehyde/urea (F/U) mole ratios (1.4, 1.2, and 1.0) were modified, after resin synthesis, by adding four additives such as sodium hydrosulfite, sodium bisulfite, acrylamide, and polymeric 4,4′‐diphenylmethane diisocyanate (pMDI). All additives were added to UF resins with three different F/U mole ratios before curing the resin. The hydrolytic stability of UF resins was determined by measuring the mass loss and liberated formaldehyde concentration of cured and modified UF resins after acid hydrolysis. Modified UF resins of lower F/U mole ratios of 1.0 and 1.2 showed better hydrolytic stability than the one of higher F/U mole ratio of 1.4, except the modified UF resins with pMDI. The hydrolytic stability of modified UF resins by sulfur compounds (sodium bisulfate and sodium hydrosulfite) decreased with an increase in their level. However, both acrylamide and pMDI were much more effective than two sulfur compounds in terms of hydrolytic stability of modified UF resins. These results indicated that modified UF resin of the F/U mole ratio of 1.2 by adding acrylamide was the most effective in improving the hydrolytic stability of UF resin. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Phenol–urea–formaldehyde resin co-polymer synthesis and its influence on Elaeis palm trunk plywood mechanical performance evaluated by 13C NMR and MALDI-TOF mass spectrometry

This study evaluated a new method of producing phenol–urea–formaldehyde (PUF) adhesives formulated differently under actual “in-situ” resin synthesis conditions. This was carried out by co-polymerizing urea formaldehyde (UF) resin with phenol–formaldehyde resin in the core layer of low molecular weight (LMW) phenol–formaldehyde (PF) resin treated Elaeis palm trunk veneers during the gluing process of Elaeis palm plywood. Matrix assisted laser desorption Ionization time of flight (MALDI-TOF) mass spectrometry (MS) illustrated and confirmed a series number of the phenol–urea co-condensates repeating unit in the prepared PUF resins which corroborated well with its mechanical properties (modulus of elasticity and modulus of rupture), bonding quality (dry test and weather boil proof or WBP test) and physical properties. A series of PF, UF and PUF resins oligomers forming repeating units up to 1833 Da were identified. Besides that, the solid state ¹³Carbon nuclear magnetic resonance (NMR) interpretation identified that the signal at 44–45 ppm and 54–55 ppm corresponding to methylene bridges were co-condensated in between phenol and urea in the PUF resin system. The ¹³C NMR investigation showed that the synthesis process of PUF resin contained no free formaldehyde elements. Furthermore, the proportion of urea and methylolureas in the mixture to synthesis PUF resin were sufficient and incorporated well into the formulation by reacting with LMWPF units to form co-condensed methylene bridges. This study showed a new and useful method to synthesize PUF resin during the gluing process of manufactured Elaeis palm plywood which can also enhance the performance of Elaeis palm plywood panels for structural instead of utility grade applications.     

Examination of selected synthesis and room‐temperature storage parameters for wood adhesive‐type urea–formaldehyde resins by 13C‐NMR spectroscopy. V

The effects of posttreatments of particleboard adhesive‐type urea–formaldehyde resins were studied. The resins were synthesized with formaldehyde/first urea (F/U₁) mol ratios of 1.40, 1.60, 1.80, 2.10, and 2.40 and then the second urea was added to give a final formaldehyde/urea ratio of 1.15 in alkaline pH. The resins were posttreated at 60°C for up to 13.5 h and the 2.5‐h heat‐treated resin samples were stored at room temperature for up to 27 days. Resins sampled during the posttreatments were examined by ¹³C‐NMR and evaluated by bonding particleboards. In the posttreatments, hydroxymethyl groups on the polymeric resin components dissociated to formaldehyde and reacted with the second urea, and methylene and methylene–ether groups were formed from reactions involving the second urea. Methylene–diurea and urea groups bonded to UF polymers were identified. As a result, the viscosity of the resins initially decreased but later increased along with the cloudiness of the resins. Bond‐strength and formaldehyde‐emission values of particleboard varied with posttreatment variables as well as with the F/U₁ mol ratios used in the resin syntheses. The results would be useful in optimizing resin synthesis and handling parameters. Various reaction mechanisms were considered. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1896–1917, 2003     

NMR study of the stabilities of urea–formaldehyde resin components toward hydrolytic treatments

The solid residues of nine urea–formaldehyde (UF) resins after hydrolytic treatment at pH4 and 86°C for 20 h and the solid residues of one UF resin after eight different hydrolytic treatments were examined by ¹³C-CP–MAS NMR. The relative stability toward hydrolysis of each structural component in each UF resin was established for various hydrolytic conditions. In general, UF resins prepared from starting mixtures with a formal F/U molar ratio of 1.00 show a high degree of stability toward hydrolysis. Cross-linking methylene linkages in the UF resins show a higher susceptibility to hydrolytic treatments at pH 4 and 86°C than do linear methylene linkages. UF resins prepared with an F/U molar ratio of 2.00 are susceptible to hydrolysis at pH 4 and 86°C. Dimethylene ether linkages, methylols attached to tertiary amides, and poly(oxymethylene glycol) moieties are probably the main formaldehyde emitters in UF resin products. © 1994 John Wiley & Sons, Inc.     

Chemical Structure and Curing Behavior of Phenol–Urea–Formaldehyde Cocondensed Resins of High Urea Content

Phenol–urea–formaldehyde cocondensed (PUF) resins of high urea content were prepared by adding different forms of urea to the reaction system. The structure, curing behavior, and water resistance of the PUF resins were investigated, and their relations were also discussed by liquid ¹³C nuclear magnetic resonance (NMR) and different scanning calorimetry (DSC). The liquid ¹³C-NMR analysis showed that urea added in the form of methylolureas was well incorporated into the cocondensed resins by reacting with phenolic methylols to form cocondensed methylene bridges, and that the PUF resins had no free formaldehyde with any form. Unreacted urea and low molecule monosubstituted urea of PUF resins play a dominant role in the curing behavior and water resistance of resins. The peak temperature, curing time, and curing enthalpy (ΔH) value correspondingly increased, however, the water resistance of PUF resins decreased when urea content in PUF resins increased. The PUF cocondensed resin with up to 89.4 % (W _U/W _P) urea has relatively low cost, and moreover can pass the requirements of China Industry Standard for the exterior grade of structural plywood after 4-h cyclic boiling test.     

Uron and uron–urea‐formaldehyde resins

The favored pH ranges for the formation of urons in urea‐formaldehyde (UF) resins preparation were determined, these being at pH's higher than 6 and lower than 4 at which the equilibrium urons ↔ N,N′‐dimethylol ureas are shifted in favor of the cyclic uron species. Shifting the pH slowly during the preparation from one favorable range to the other causes shift in the equilibrium and formation of a majority of methylol ureas species, whereas a rapid change in pH does not cause this to any great extent. UF resins in which uron constituted as much as 60% of the resin were prepared and the procedure to maximize the proportion of uron present at the end of the reaction is described. Uron was found to be present in these resins also as linked by methylene bridges to urea and other urons and also as methylol urons, the reactivity of the methylol group of this latter having been shown to be much lower than that of the same group in methylol ureas. Thermomechanical analysis (TMA) tests and tests on wood particleboard prepared with uron resins to which relatively small proportions of urea were added at the end of the reaction were capable of gelling and yielding bonds of considerable strength. Equally, mixing a uron‐rich resin with a low F/U molar ratio UF resin yielded resins of greater strength than a simple UF of corresponding molar ratio indicating that UF resins of lower formaldehyde emission with still acceptable strength could be prepared with these resins. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 277–289, 1999     

Interphase Reaction of Isocyanates with Epoxy Resins Containing Functional Groups of Different Reactivity

Interphase reactions between cured epoxy resins and isocyanates are investigated. The epoxy resins contain secondary hydroxyl groups as reactive groups only or secondary hydroxyl plus amine. The isocyanate diffuses into the epoxy resin forming an interphase with a thickness of some micrometers. Depending on the functional groups available in the epoxy resin, urethane and urea groups are formed in the interphase. If a monofunctional isocyanate is used, no difference between both kinds of epoxy resin could be detected regarding the formation of urethane. If the epoxy resins react with bifunctional isocyanates a crosslinked interphase is formed. Due to the higher reactivity between amine and isocyanate compared to hydroxyl and isocyanate, the urea is formed first. The resulting cross‐links restrict the further diffusion of isocyanate into the epoxy resin. The consequence is a lower urethane content in the interphase and a thinner interphase compared to the epoxy resin containing hydroxyl only. If a prepolymer with isocyanate end groups is used as isocyanate the formation of the interphase is slower compared to the low molecular weight isocyanate. This is due to the reduced mobility of the prepolymer.     

Syntheses and properties of low‐level melamine‐modified urea–melamine–formaldehyde resins

Syntheses of urea–melamine–formaldehyde (UMF) resins were studied using 2–12% melamine levels and UF base resins that were preadvanced to various different extents. The melamine reaction was carried out at pH 6.3 with F/(U + M) mole ratio of 2.1 until a target viscosity of V was reached (Gardener–Holdt) and then the second urea added at pH 8.0 to give a final F/(U + M) mole ratio of 1.15. Analyses with ¹³C‐NMR and viscosity measurements showed that MF components react fast and the UF components very slowly in the melamine reaction. Therefore, as the extent of preadvancement of UF base resin was decreased, the reaction time to reach the target viscosity became longer and the MF resin components showed high degrees of polymerization. The overpolymerization of MF components resulted in increasingly more opaque resins, with viscosity remaining stable for more than a month. As the preadvancement of UF base resin was increased, the extent of advancement of MF components decreased, to give clearer resins, with viscosity slowly increasing at room temperature. Overall, preadvancing the UF base resin components to an appropriate extent was found to be a key to synthesizing various low‐level melamine‐modified UMF resins. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2559–2569, 2004     

Examination of selected synthesis and room‐temperature storage parameters for wood adhesive‐type urea–formaldehyde resins by 13C‐NMR spectroscopy. IV

Typical particleboard wood‐adhesive urea–formaldehyde (UF) resins, synthesized with formaldehyde/first urea (F/U₁) mol ratios of 1.80, 2.10, and 2.40 and the second urea added to an overall F/U ratio of 1.15, in weak alkaline pH, were allowed to stand at room temperature over a period of 50 days. ¹³C‐NMR of time samples taken over the storage period showed gradual migration of hydroxymethyl groups from the polymeric first‐urea components to the monomeric second‐urea components and also an advancing degree of polymerization of resins by forming methylene and methylene ether groups involving the second urea. These phenomena that varied with the F/U₁ mol ratios used in the resin syntheses due to the varying polymer branching structures resulted in the first step of resin synthesis. Varying viscosity decreases and increases of the resins also occurred. Due to these chemical and physical changes, the particleboards that bonded with the sampled resins showed varying bond strength and formaldehyde‐emission values, indicating process optimizations possible to improve bonding and formaldehyde‐emission performances. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1155–1169, 2001     

Reactivity,chemical structure,and molecular mobility of urea–formaldehyde adhesives synthesized under different conditions using FTIR and solid‐state 13C CP/MAS NMR spectroscopy

This study was conducted to investigate the effects of reaction pH condition and hardener type on the reactivity, chemical structure, and molecular mobility of urea–formaldehyde (UF) resins. Three different reaction pH conditions, such as alkaline (7.5), weak acid (4.5), and strong acid (1.0), were used to synthesize UF resins, which were cured by adding four different hardeners (ammonium chloride, ammonium sulfate, ammonium citrate, and zinc nitrate) to measure gel time as the reactivity. FTIR and ¹³C‐NMR spectroscopies were used to study the chemical structure of the resin prepared under three different reaction pH conditions. The gel time of UF resins decreased with an increase in the amount of ammonium chloride, ammonium sulfate, and ammonium citrate added in the resins, whereas the gel time increased when zinc nitrate was added. Both FTIR and ¹³C‐NMR spectroscopies showed that the strong reaction pH condition produced uronic structures in UF resin, whereas both alkaline and weak‐acid conditions produced quite similar chemical species in the resins. The proton rotating‐frame spin–lattice relaxation time (T_1ρH) decreased with a decrease in the reaction pH of UF resin. This result indicates that the molecular mobility of UF resin increases with a decrease in the reaction pH used during its synthesis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2677–2687, 2003     

Novel polyurethane polyols for waterborne and high solids coatings

Recently developed oligomeric β-hydroxyalkyl urethane polyols are finding application as modifiers and crosslinkers for waterborne and high solids coatings. In waterborne coatings, urethane polyols can be used as modifiers for acrylic, polyester or alkyd melamine resin crosslinked coatings to replace the cosolvent. In high solids coatings, polyurethane polyols are being employed to raise the application solids, increase film hardness and water resistance, and exterior durability.

There are also applications for polyurethane diols as resin intermediates and in the preparation of blocked isocyanate crosslinkers. β-Hydroxyalkyl urethane diol or polyols can be prepared by an isocyanate reaction with a diol, such as 1,2-propylene glycol, but also by non-isocyanate processes. The non-isocyanate routes to urethanes can utilize carbon monoxide, carbon dioxide, urea or organic carbonates as a carbonyl source for the carbamic acid ester.

It is possible to split these urethanes to the isocyanate, but interest has concentrated on using the urethane intermediates directly in coating applications without going through the isocyanate. The structures reported are bis-hydroxyalkyl urethane intermediates and derivatives of these compounds.     

Kinetic study of the urethane and urea reactions of isophorone diisocyanate

Kinetic studies of the catalyzed urethane reactions between isophorone diisocyanate (IPDI) and alcohols and of the urea reactions between an isocyanate‐terminated prepolymer [IPDI–PPG2000–IPDI, where PPG2000 is poly(propylene glycol) with a number‐average molecular weight of 2000 g/mol] and water in the bulk state were performed with Fourier transform infrared (FTIR) spectroscopy. Dibutyltin dilaurate was used as the catalyst for the urethane reaction, and various tertiary amines were used as catalysts for the urea reactions. The reactions were followed through the monitoring of the change in the intensity of the absorbance band for NCO stretching at 2270 cm^?1 in the FTIR spectra; the activation parameters were determined through the evaluation of the kinetic data obtained at various temperatures (within the range of 30–60°C). The kinetic data indicated that the catalyzed isocyanate/alcohol and isocyanate/water reactions both followed second‐order kinetics during their initial stages but later followed third‐order kinetics resulting from the autocatalytic effects of hydrogen bonding between the hydroxyl groups and the newly formed urethane and urea groups. Furthermore, activation energies of 64.88 and about 80 kJ/mol for the isocyanate/alcohol and isocyanate/water reactions, respectively, indicated that the urea‐forming reactions were more sensitive to the reaction temperature than the urethane‐forming reactions. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008