Morphology of EVA based nanocomposites under shear and extensional flow

Shear and extensional rheological measurements were conducted in conjunction with laser light scattering (LLS) on ethylene‐vinyl acetate copolymer (EVA) nanocomposites. The materials were prepared by melt‐mixing EVA and commercially acquired layered silicates. Wide Angle X‐Ray Scattering (WAXS) was used to ascertain the degree of layer swelling. This could be attributed to the intercalation of polymer chains into the interlayer of the silicates. The nanocomposites prepared were determined to be predominantly intercalated in nature. In shear rheological tests, the nanocomposites exhibited an increase in viscoelastic properties compared to the pure EVA. The extent of this property enhancement was not as pronounced as had been reported in many instances with respect to other polymer nanocomposites. This could be attributed to the absence of a network structure normally observed in an exfoliated system. The extensional rheological tests showed an increase in extensional flow properties. This was confirmed by the LLS, which indicated that the filled systems had higher deformability than the unfilled one. Polym. Eng. Sci. 44:1220–1230, 2004. © 2004 Society of Plastics Engineers.     

Nanostructure of EVA/organoclay nanocomposites: Effects of kinds of organoclays and grafting of maleic anhydride onto EVA

Nanostructure of poly(ethylene‐co‐vinyl acetate)/organically modified montmorillonite (MMT; EVA/organoclay) nanocomposites prepared by melt intercalation process was investigated using X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Three kinds of organoclays were used to see their influences on the nanostructure of the EVA hybrids. The effects of the polar interactions between the polymer and the silicate layers of organoclays were also investigated by grafting maleic anhydride onto EVA. It was found that the strong polar interactions between the polymer and the silicate layers of organoclays are critical to the formation of polymer‐layered silicate nanocomposites. The results also showed that increasing the mixing temperature was unfavorable to improve the dispersion of organoclays in the EVA matrix. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1901–1909, 2003     

Flame retardant properties of EVA‐nanocomposites and improvements by combination of nanofillers with aluminium trihydrate

Flame retardant nanocomposites are synthesized by melt‐blending ethylene–vinyl acetate copolymers (EVA) with modified layered silicates (montmorillonites). Thermogravimetric analysis performed under different atmospheres (nitrogen and air) demonstrated a clear increase in the thermal stability of the layered silicate‐based nanocomposites. The use of the cone calorimeter to investigate the fire properties of the materials indicated that the nanocomposites caused a large decrease in heat release. The char‐formation is the main factor important for improvement and its function is outlined. Further improvements of the flame retardancy by combinations of nanofillers and traditional FR‐additives on the basis of metal hydroxides were also studied. Copyright © 2002 John Wiley & Sons, Ltd.     

Ethylene vinyl acetate/Mg‐Al LDH nanocomposites by solution blending

Partially exfoliated ethylene vinyl acetate (EVA‐40, 40% vinyl acetate content)/layered double hydroxide (LDH) nanocomposites using organically modified layered double hydroxide (DS‐LDH) have been synthesized by solution intercalation method. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) studies of nanocomposites shows the formation of exfoliated LDH nanolayers in EVA‐40 matrix at lower DS‐LDH contents and partially intercalated/exfoliated EVA‐40/MgAl LDH nanocomposites at higher DS‐LDH contents. These EVA‐40/MgAl LDH nanocomposites demonstrate a significant improvement in tensile strength and elongation at break for 3 wt% of DS‐LDH filler loading compare to neat EVA‐40 matrix. Thermogravimetric analysis also shows that the thermal stability of the nanocomposites increases with DS‐LDH content in EVA‐40. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Ethylene propylene diene terpolymer/ethylene vinyl acetate/layered silicate ternary nanocomposite by solution method

A new ternary nanocomposite has been developed using ethylene propylene diene terpolymer (EPDM), ethylene vinyl acetate (EVA‐45) copolymer, and organically modified layered silicate (16 Me‐MMT) from sodium montmorillonite (Na⁺‐MMT). Wide angle X‐ray diffraction and transmission electron microscopic analysis confirmed the intercalation of the polymer chains in between the organosilicate layers and the nanoscale distribution of 16 Me‐MMT in polymer matrix, respectively. The measurement of mechanical properties for 2–8 wt% of 16 Me‐MMT loadings showed a significant increase in tensile strength, elongation at break, and modulus at different elongations. Such an improvement in mechanical properties has been correlated based on the fracture behavior of nanocomposite by SEM analysis. Thermal stability of EPDM/EVA/layered silicate ternary nanocomposites also showed substantial improvements compared with the neat EPDM/EVA blend, confirming thereby the formation of a high performance nanocomposite. POLYM. ENG. SCI., 46:437–843, 2006. © 2006 Society of Plastics Engineers     

Effect of layered silicate on EPDM/EVA blend nanocomposite: Dynamic mechanical,thermal, and swelling properties

Polymer blend nanocomposites have been developed by solution method using ethylene propylene diene terpolymer (EPDM), ethylene vinyl acetate (EVA‐45) copolymer, and organically modified layered silicate. Morphological investigation made by wide‐angle X‐ray diffraction and transmission electron microscopic analysis indicates intercalated structure of EPDM/EVA nanocomposites with partial disorder. Scanning electron microscopic studies exhibit the phase behavior of EPDM/EVA blend nanocomposites. Dynamic mechanical thermal analysis shows a significant increase in storage modulus in the rubbery plateau. The decrease in damping (tan δ) value and enhanced glass‐transition temperature (T_g) demonstrate the reinforcing effect of layered silicate in the EPDM/EVA blend matrix. The tensile modulus of these nanocomposites also showed a significant improvement with the filler content. The main chain scission of EPDM/EVA blend nanocomposites compared with the neat EPDM/EVA blend showed substantial improvement in thermal stability in nitrogen, whereas a sizeable increase is observed in air. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Natural rubber/poly(ethylene‐co‐vinyl acetate)‐blend‐based nanocomposites

Natural rubber (NR)/poly(ethylene‐co‐vinyl acetate) (EVA) blend–clay nanocomposites were prepared and characterized. The blend nanocomposites were prepared through the melt mixing of NR/EVA in a ratio of 40/60 with various amounts of organoclay with an internal mixer followed by compression molding. X‐ray diffraction patterns revealed that the nanocomposites formed were intercalated. The formation of the intercalated nanocomposites was also indicated by transmission electron microscopy. Scanning electron microscopy, used to study the fractured surface morphology, showed that the distribution of the organoclay in the polymer matrix was homogeneous. The tensile modulus of the nanocomposites increased with an increase in the organoclay content. However, an increase in the organoclay content up to 5 phr did not affect the tensile strength, but the organoclay reduced this property when it was increased further. This study also indicated that a low silicate content dispersed in the blend matrix was capable of increasing the storage modulus of the material. The addition of the organoclay also increased the decomposition temperature of the NR/EVA blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 353–362, 2006     

Rubber/LDH nanocomposites by solution blending

The rubber nanocomposites containing ethylene vinyl acetate (EVA) having 60 wt % of vinyl acetate content and organomodified layered double hydroxide (DS‐LDH) as nanofiller have been prepared by solution intercalation method and characterized. The XRD and TEM analysis demonstrate the formation of completely exfoliated EVA/DS‐LDH nanocomposites for 1 wt % filler loading followed by partially exfoliated structure for 5–8 wt % of DS‐LDH content. EVA/DS‐LDH nanocomposites show improved mechanical properties such as tensile strength (TS) and elongation at break (EB) in comparison with neat EVA. The maximum value of TS (5.1 MPa) is noted for 3 wt % of DS‐LDH content with respect to TS value of pure EVA (2.6 MPa). The data from thermogravimetric analysis show the improvement in thermal stability of the nanocomposites by ≈15°C with respect to neat EVA. Limiting oxygen index measurements show that the nanocomposites act as good flame retardant materials. Swelling property analysis shows improved solvent resistance behavior of the nanocomposites (1, 3, and 5 wt % DS‐LDH content) compared with neat EVA‐60. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Short communication: Carbon nanotubes as flame retardants for polymers

Flame retardant nanocomposites were synthesized by melt‐blending ethylene‐vinyl acetate copolymer (EVA) with multi wall carbon nanotubes. Fire property measurements by cone calorimeter revealed that the incorporation of multi wall carbon nanotubes into EVA significantly reduced the peak heat release rates compared with the virgin EVA. Peak heat release rates of EVA with multi‐wall carbon nanotubes were slightly improved compared with EVA nanocomposites based on modified layered silicates. Char formation is the main important factor for these improvements. There was also a synergistic effect by the combination of carbon nanotubes and organoclays resulting in an overall more perfect closed surface with improved heat release values. Copyright © 2002 John Wiley & Sons, Ltd.     

Ethylene vinyl acetate/ethylene propylene diene terpolymer‐blend‐layered double hydroxide nanocomposites

Ethylene vinyl acetate (EVA‐45)/ethylene propylene diene terpolymer (EPDM) blend‐layered double hydroxide (LDH) nanocomposites have been prepared by solution blending of 1:1 weight ratio of EVA and EPDM with varying amounts of organo LDH (DS‐LDH). X‐ray diffraction and transmission electron microscopy analysis suggest the formation of partially exfoliated EVA/EPDM/DS‐LDH nanocomposites. Measurement of mechanical properties of the nanocomposites (3 wt% DS‐LDH content) show that the improvement in tensile strength and elongation at break are 35 and 12% higher than neat EVA/EPDM blends. Dynamic mechanical thermal analysis also shows that the storage modulus of the nanocomposites at glass transition temperature is higher compared to the pure blend. Such improvements in mechanical properties have been correlated in terms of fracture behavior of the nanocomposites using scanning electron microscopy analysis. Thermal stability of the prepared nanocomposites is substantially higher compared to neat EVA/EPDM blend, confirming the formation of high‐performance polymer nanocomposites. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Effect of vinyl acetate content on the mechanical and thermal properties of ethylene vinyl acetate/MgAl layered double hydroxide nanocomposites

Ethylene vinyl acetate (EVA)/Mg‐Al layered double hydroxide (LDH) nanocomposites using EVA of different vinyl acetate contents (EVA‐18 and EVA‐45) have been prepared by solution blending method. X‐ray diffraction and transmission electron microscopic studies of nanocomposites clearly indicate the formation of exfoliated/intercalated structure for EVA‐18 and completely delaminated structure for EVA‐45. Though EVA‐18 nanocomposites do not show significant improvement in mechanical properties, EVA‐45 nanocomposites with 5 wt % DS‐LDH content results in tensile strength and elongation at break to be 25% and 7.5% higher compared to neat EVA‐45. The data from thermogravimetric analysis show that the nanocomposites of EVA‐18 and EVA‐45 have ≈10°C higher thermal decomposition temperature compared to neat EVA. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Rheological behavior of polypropylene/layered silicate nanocomposites prepared by melt compounding in shear and elongational flows

Melt rheology and processability of exfoliated polypropylene (PP)/layered silicate nanocomposites were investigated. The nanocomposites were prepared by melt compounding process in the presence or absence of a PP‐based maleic anhydride compatibilizer. PP/layered silicate nanocomposites showed typical rheological properties of exfoliated nanocomposites such as nonterminal solid‐like plateau behavior at low frequency region in oscillatory shear flow, higher steady shear viscosity at low shear rate region, and outstanding strain hardening behavior in uniaxial elongational flow. The melt processability of exfoliated PP/layered silicate nanocomposites was significantly improved due to good dispersion of layered silicates and increased molecular interaction between the PP matrix and the layered silicate organoclay. Small‐angle X‐ray scattering and transmission electron microscopy results revealed that the layered silicate organoclay was exfoliated and good interaction between PP matrix and organoclay was achieved by using the PP‐g‐MAH compatibilizer. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3506–3515, 2007     

Heat Induced Structure Modifications in Polymer‐Layered Silicate Nanocomposites

Summary: The success of the use of layered silicates in polymer nanocomposites, to improve physical and chemical properties is strictly related to a deeper knowledge of the mechanistic aspects on which the final features are grounded. This work shows the temperature induced structural rearrangements of nanocomposites based on poly[ethylene‐co‐(vinyl acetate)] (EVA) intercalated‐organomodified clay (at 3–30 wt.‐% silicate addition) which occur in the range between 75 and 350 °C. In situ high temperature X‐ray diffraction (HT‐XRD) studies have been performed under both nitrogen and air to monitor the modifications of the nanocomposite structure at increasing temperatures under inert/oxidative atmosphere. Heating between 75 and 225 °C, under nitrogen or air, causes the layered silicate to migrate towards the nanocomposite surface and to increase its interlayer distance. The degradation of both the clay organomodifier and the VA units of the EVA polymer seems to play a key role in driving the evolution of the silicate phase in the low temperature range. The structural modifications of the nanocomposites in the high temperature range (250–350 °C), depended on the atmosphere, either inert or oxidizing, in which the samples were heated. Heating under nitrogen led to deintercalation and thus a decrease of the silicate interlayer space, whereas exfoliation was the main process under air leading to an increase of the silicate interlayer space.

Heat induced structural modification of EVA‐clay nanocomposite under nitrogen and air.     

Mechanical and rheological properties of the maleated polypropylene–layered silicate nanocomposites with different morphology

Three types of maleated polypropylene–layered silicate nanocomposites with different dispersion states of layered silicate (deintercalated, intercalated, and exfoliated states) are prepared from two kinds of polypropylenes with different molecular weights, organically modified layered silicate and pristine montmorillonite to investigate the effect of the final morphology of the nanocomposite on the rheological and mechanical properties. Maleated polypropylene with high molecular weight intercalates slowly and the other with low molecular weight exfoliates fast into the organophilic layered silicates. Rheological properties such as oscillatory storage modulus, nonterminal behavior, and relative viscosity has close relationship with the dispersion state of layered silicates. The exfoliated nanocomposite shows the largest increase and the deintercalated nanocomposite shows almost no change in relative shear and complex viscosities with the clay content. The exfoliated nanocomposite shows the largest drop in complex viscosity due to shear alignment of clay layers in the shear flow. In addition, the final dispersion state of layered silicates intimately relates to the mechanical property. The dynamic storage moduli of nanocomposites show the same behavior as the relative shear and complex viscosities. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1526–1535, 2003     

Microstructure and thermal properties of ethylene‐(vinyl acetate) copolymer/rectorite nanocomposites

Ethylene‐(vinyl acetate) copolymer (EVA)/rectorite nanocomposites were prepared by direct melt extrusion of EVA and organo‐rectorite. The microstructures and thermal properties of EVA nanocomposites were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), solid‐state nuclear magnetic spectroscopy, positron annihilation spectroscopy, thermal gravimetric analysis (TGA) and dynamic mechanical analysis techniques. XRD pattern and SEM images show that the intercalated structure is formed and rectorite is finely dispersed in EVA matrix. When organoclay content of the hybrid increases to 7.5 wt%, or pristine rectorite was used instead of organoclay, the crystallization behavior of EVA nanocomposite changes greatly and the ratio of the monoclinic to orthorhombic crystal increases significantly. The relative fractional free volume of the nanocomposite decreases with the increasing organo‐rectorite content, and the values of damping factor (tan δ) for all nanocomposites are lower than that of pure EVA. These facts illuminate that intercalated structure restricts the segment motion and mobilization of polymer chain. TGA results of EVA nanocomposites in air indicate that deacylation of EVA is accelerated because of the catalytic effect and the thermal degradation of the main chain is delayed owing to the barrier effect of silicate layers. Copyright © 2005 Society of Chemical Industry     

Technological and processing properties of natural rubber layered silicate‐nanocomposites by melt intercalation process

Natural rubber nanocomposites were produced by melt‐mixing of natural rubber with organically modified silicates. For comparison, a pristine‐layered silicate and a nonlayered version [English Indian clay (EIC)] were also included in the study. The layered silicate used was sodium bentonite (BNT) and organoclays used were octadecylamine‐ modified montmorillonite (MMT‐ODA) and methyltallow bis‐2‐hydroxyethyl ammonium‐modified montmorillonite (MMT‐ TMDA). Accelerated sulfur system was used for the vulcanization of the nanocomposites. The dispersion of these silicates was studied by X‐ray diffraction and transmission electron microscopy. The organoclay‐incorporated composites exhibited faster curing and improved mechanical properties. The improvement in the mechanical properties of the composites followed the order MMT‐ODA > MMT‐TMDA > EIC > BNT. The property improvement was attributed to the intercalation/exfoliation of the organically modified silicates because of their high initial interlayer distance. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2537–2543, 2006     

Using maleic anhydride grafted poly(lactic acid) as a compatibilizer in poly(lactic acid)/layered‐silicate nanocomposites

The goal of this work was to prepare exfoliated poly(lactic acid) (PLA)/layered‐silicate nanocomposites with maleic anhydride grafted poly(lactic acid) (PLA–MA) as a compatibilizer. Two different layered silicates were used in the study: bentonite and hectorite. The nanocomposites were prepared by the incorporation of each layered silicate (5 wt %) into PLA via solution casting. X‐ray diffraction of the prepared nanocomposites indicated exfoliation of the silicates. However, micrographs from transmission electron microscopy showed the presence of intercalated and partially exfoliated areas. Tensile testing showed improvements in both the tensile modulus and yield strength for all the prepared nanocomposites. The results from the dynamic mechanical thermal analysis showed an improvement in the storage modulus over the entire temperature range for both layered silicates together with a shift in the tan δ peak to higher temperatures. The effect of using PLA–MA differed between the two layered silicates because of a difference in the organic treatment. The bentonite layered silicate showed a more distinct improvement in exfoliation and an increase in the mechanical properties because of the addition of PLA–MA in comparison with the hectorite layered silicate. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1852–1862, 2006     

Synthesis and characterization of ethylene vinyl acetate/Mg–Al layered double hydroxide nanocomposites

Mg–Al layered double hydroxide (LDH)/Ethylene vinyl acetate (EVA‐28) nanocomposites were prepared through solution intercalation method using organically modified layered double hydroxide (DS‐LDH). DS‐LDH was made by the intercalation of sodium dodecyl sulfate (SDS) ion. The structure of DS‐LDH and its nanocomposites with EVA‐28 was determined by X‐ray diffraction (XRD) and transmission electron microscope (TEM) analysis. XRD analysis shows that the original peak of DS‐LDH shifted to lower 2θ range and supports the formation of intercalated nanocomposites while, TEM micrograph shows the presence of partially exfoliated LDH nanolayers in addition to orderly stacked LDH crystallites in the polymer matrix. The presence of LDH in the nanocomposites has been confirmed by Fourier transform infrared (FTIR) analysis. The mechanical properties show significant improvement for the nanocomposite with respect to neat EVA‐28. Thermogravimetric (TGA) analysis shows that thermal stability of the nanocomposites is higher than that of EVA‐28. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1845–1851, 2007     

Preparation and characterization of ethylene vinyl acetate copolymer/montmorillonite nanocomposite

Ethylene vinyl acetate copolymer (EVA) and monmorillonite (MMT) nanocomposites have been investigated as a function of vinyl acetate content and molecular weight of EVA and types of substituted alkyl ammonium of MMT. It is found that vinyl acetate content and type of substituted alkyl ammonium are important factors for the intercalation behaviour of MMT in MMT/EVA nanocomposite. Maleic anhydride grafted high‐density polyethylene was used as a compatibilizer to improve the intercalation behaviour of MMT. X‐ray diffraction and transmission electron microscopy were used to characterize the intercalation/exfoliation behaviour, and mechanical properties were measured. © 2003 Society of Chemical Industry     

Ethylene Vinyl Acetate and Polycaprolactone–Organoclay Nanocomposite: Thermal,Mechanical and Morphological Properties

Organoclay of the type Cloisite^® 20A (C-20A) with two structurally different but semicrystalline polymer matrices was studied. Polycaprolactone (PCL), a linear, biodegradable polymer, and ethylene vinyl acetate (EVA), a branched copolymer, were chosen to prepare polymer clay nanocomposites via the melt-blending method. The results show that the structure of a polymer matrix plays a significant role towards compatibilization with the silicate layers of the clay. Scanning electron microscopy and X-ray diffraction analyses revealed an exfoliated-intercalated mixed morphology for the PCL matrix. However, for the EVA matrix, silicate layers agglomerated to form tactoids and resulted primarily in an intercalated morphology. Fourier transform infrared spectroscopy was used to determine the nature of the interactions between the polymer and the filler. The thermal properties were investigated using thermogravimetric analysis and indicated that, with an increase in clay loading, the thermal stability was reduced for both matrices. Tensile tests suggested that Young’s modulus improved for the EVA matrix with an increase in clay dosage whereas for PCL the modulus was found to be highest for 8% clay loading.