Effect of different curing systems on heat shrinkability and mechanical properties of ethylene vinyl acetate/epoxidized natural rubber blends

Ethylene vinyl acetate (EVA)/epoxidized natural rubber (ENR) blends containing 10 and 30 wt % ENR were prepared by using an internal mixer. Five different types of curing systems were employed: dicumyl peroxide (DCP), sulfur (S), phenolic resin (Ph), DCP + S, and DCP + Ph. DCP could crosslink with both EVA and ENR while S and Ph were curing agents for ENR. The DCP system provided the lowest tensile properties and tear strength because of low crosslinking in ENR phase. Addition of sulfur or phenolic resin increased the mechanical properties due to a better vulcanization of the rubber phase. The mechanical properties of the blends decreased with increasing ENR content. The rubber particle size in the blends containing 30% ENR played a more important role in the mechanical properties than the blends containing 10% ENR. ENR particle size did not affect heat shrinkability of EVA and a well vulcanized rubber phase was not required for high heat shrinkage. Furthermore, heat shrinkage of the blends slightly changed as the ENR content increased for all curing systems. With regard to the mechanical properties and heat shrinkability, the most appropriate curing system was DCP + Ph and in the case the 10 wt % ENR content produced a more favorable blend. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of different types of peroxides on properties of vulcanized EPDM + PP blends

Mechanical and tribological behavior of several dynamic vulcanizate blends of polypropylene (PP) with ethylene‐propylene‐diene rubber (EPDM) was examined and compared with those of uncrosslinked blends. Vulcanization was performed using two types of organic peroxides combined with (meth)acrylate coagent. The effect of different types and concentrations of peroxides as crosslinking agents on the properties of the resulting materials were investigated. Dicumyl peroxide (DCP) provides higher reactivity and exhibits nearly the same crosslinking efficiency for both 60/40 and 50/50 blends; almost fully crosslinked samples are obtained if the compound contains 1.0 or 2.0 wt% DCP. These results correlate to the gel content and mechanical properties of our materials. Variation of PP + elastomer ratio does not have a significant influence on friction. From 60/40 group of composites, lower friction values were obtained for samples cured with 0.5 wt% benzoyl peroxide (BP) and 1.0 wt% DCP. The tribological properties of the samples with higher amount of DCP show rubbery rather than a toughened thermoplastic behavior. Wear of the composites decreases with the increasing concentration of the curing agent. Compared to BP, the samples cured with DCP display lower wear. POLYM. COMPOS., 31:1678–1691, 2010. © 2010 Society of Plastics Engineers.     

The use of EVA-containing mercapto groups in natural rubber-EVA blends. II. The effect of curing system on mechanical and thermal properties of the blends

Natural rubber (NR)-poly(ethylene-co-vinyl acetate) (EVA) blends have been studied by incorporation of mercapto-modified EVA (EVASH) combined with dicumyl peroxide (DCP) as a curing agent. The mechanical, thermal, and morphological properties of NR-EVA blends as functions of blend composition and compatibilizer and/or curative additions were investigated. An EVASH-DCP combined system leads to the greatest improvement in tensile strength when EVA is dispersed within the NR matrix. Higher performance on Shore A hardness was also achieved with this combined system. For blends characterized by NR domains dispersed in the EVA matrix, the efficiency of pure DCP in improving the tensile strength is higher. Morphological observations and selective extraction experiments indicate the cross-linking of NR phase in both systems. A cross-linking of the EVA phase is also suggested by DCP or an EVASH-DCP combined system, based on the decreasing degree of crystallinity of this phase. © 1996 John Wiley & Sons, Inc.     

Rheological properties and crystalline structure of the dynamically cured EPDM and PP/HDPE ternary blends

The rheological properties and crystalline structure of the polyolefin ternary blends of EPDM/polypropylene/high density polyethylene were studied. Blends were prepared in a laboratory internal mixer by two different methods. In blend–cure process, blending and curing were performed simultaneously and EPDM was cured by dicumyl peroxide (DCP) in the presence of PP/HDPE under shear. The cure–blend was to cure EPDM alone first under shear (dynamic curing) and then mix the cured EPDM with PP and HDPE. The effect of DCP concentration, intensity of the shear mixing, and the rubber/plastic composition were studied using capillary rheometer and X-ray diffractometer. The PP-rich ternary blends showed the effect of the mechanooxidative degradation of PP by shear and peroxide. The melt viscosity increased with increasing DCP concentration in blends of EPDM-rich compositions. X-ray diffraction studies revealed that the inclusion of 25 wt % of linear EPDM in the PP/HDPE mixture for the PP-rich ternary blends changed the crystal structure of polypropylene component in the ternary blends. However, the dynamic curing did not alter the crystal structure of PP or HDPE in the blends.     

Dynamic vulcanization of recycled milk pouches (LDPE–LLDPE) and EPDM blends using dicumyl peroxide

The viability of thermomechanical recycling of post‐consumer milk pouches (blend of low‐density polyethylene (LDPE) and linear low‐density polyethylene (LLDPE)) and its scope for suitable engineering applications were investigated. The effects of blending with ethylene‐propylene‐diene monomer (EPDM) rubber and subsequent curing using dicumyl peroxide (DCP) on the macromolecular structure and properties of recycled polyethylene (PE) blends were studied. The crosslinking efficiency of recycled PE/EPDM blends and possible thermooxidative degradation of recycled polymer upon peroxide curing was assessed using torque and gel content measurements along with infrared spectroscopic analysis. Both the torque and gel content of the blends varied with DCP crosslinking reactions and also were affected by oxidative degradation. In view of the electrical application area of this recycled blend material, the dielectric breakdown strength and volume resistivity were measured. The mechanical performance and thermal stability of recycled PE/EPDM blends improved with progressive crosslinking by DCP but deteriorated somewhat at higher DCP dose. Scanning electron microscopy showed good interface bonding between recycled polymer and dispersed EPDM phase in the cured blends compared to the non‐cured blends. Copyright © 2007 Society of Chemical Industry     

Mechanical and aging properties of cross‐linked ethylene propylene diene rubber / styrene butadiene rubber blends

The mechanical properties and aging characteristics of blends of ethylene propylene diene monomer (EPDM) rubber and styrene butadiene rubber (SBR) were investigated with special reference to the effect of blend ratio and cross‐linking systems. Among the blends, the one with 80/20 EPDM/SBR has been found to exhibit the highest tensile, tear, and abrasion properties at ambient temperature. The observed changes in the mechanical properties of the blends have been correlated with the phase morphology, as attested by scanning electron micrographs (SEMs). The effects of three different cure systems, namely, sulfur (S), dicumyl peroxide (DCP), and a mixed system consisting of sulfur and peroxide (mixed) on the blend properties also were studied. The stress‐strain behavior, tensile strength, elongation at break, and tear strength of the blends were found to be better for the mixed system. The influence of fillers such as high‐abrasion furnace (HAF) black, general‐purpose furnace (GPF) black, silica, and clay on the mechanical properties of 90/10 EPDM/SBR blend was examined. The ozone and water aging studies also were conducted on the sulfur cured blends, to supplement the results from the mechanical properties investigation. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2606–2621, 2004     

HNBR/EPDM blends: Covulcanization and compatibility

The covulcanization characteristics, mechanical properties, compatibility, and hot‐air aging resistance of hydrogenated nitrile‐butadiene rubber (HNBR)/ethylene‐propylene‐diene rubber (EPDM) blends cured with either sulfur or dicumyl peroxide (DCP) were studied. The difference between M_H and M_L (M_H ? M_L), rheometer graphs, selective swelling and a dynamic mechanical analysis of HNBR/EPDM blends confirmed that the peroxide curing system gives better covulcanization characteristics than the sulfur curing system and peroxide exhibited higher crosslink efficiency on EPDM while sulfur showed larger crosslink efficiency on HNBR. Dynamic mechanical analysis and morphology indicated that the compatibility between HNBR and EPDM is limited. Tensile strength and elongation at break of the sulfur‐cured blends are greater than those obtained with peroxide and increase with the HNBR fraction. The blends crosslinked with peroxide retain their tensile strength but not their elongation at break after hot air ageing better than blends vulcanized by sulfur. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of rubber content on mechanical properties and heat shrinkage of ethylene vinyl acetate copolymer blended with epoxidized natural rubber

Ethylene vinyl acetate (EVA, 18 mol % vinyl acetate) and epoxidized natural rubber (ENR, 50 mol % epoxidation) were blended in an internal mixer and compared to EVA. Dicumyl peroxide (DCP) was used as a curing agent. The blends consisted of 10–50 wt % of ENR and were compared with crosslinked EVA in terms of heat shrinkage, mechanical properties, and degree of crystallinity. It is found that the blends showed a decrease in mechanical properties with increasing ENR content because DCP was not a good vulcanizing agent of ENR. The addition of ENR did not affect heat shrinkability of EVA. The maximum heat shrinkage obtained was 80% for EVA and the blends. ENR did not affect thermal properties of EVA investigated by the differential scanning calorimetry. The X‐ray diffractometry showed discrepancy in degree of crystallinity before and after specimen stretching and after heat shrinking. It is believed that ENR particles decreased molecular orientation of EVA resulting in a decrease in degree of crystallinity but the remained orientation was sufficient for heat shrinking. The blend showed better extrudability than EVA after increasing take‐up speed. Therefore, the extruded tube prepared from the blend provided higher heat shrinkage than EVA tube. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of peroxide and phenolic cure systems on characteristics of the filled ethylene–propylene–diene monomer rubber (EPDM)

The effects of three curing systems, peroxide, peroxide–phenolic combination, and phenolic on selected properties of cured carbon black‐filled ethylene–propylene–diene monomer rubber (EPDM) were investigated. The cured rubbers immersed in hot amine solution to evaluate their suitability for seal and gasket industry at elevated temperature and amine environments. These tests were essential for evaluating the durability of the gasket in a gas refinery. The Fourier transform infrared spectroscopy spectrums revealed that the phenolic crosslink was constructed between rubber macromolecules during the curing process. The changing curing system from peroxide to peroxide–phenolic and phenolic increased the glass transition temperature of the filled cured rubbers between 3 and 5 °C. There was not any significant difference between thermogravimetric analysis thermographs of the selected cured rubbers with various cure systems and the residues ranged between 45% and 47%. Unlike of peroxide curing system, a dual phase was observed from scanning electron microscopy micrographs for peroxide–phenolic and phenolic cure systems. The phenolic cure system was not beneficial for rubber curing although, it reduced scorch time of the curing process. For the most studied mechanical properties, phenolic cure system deteriorated mechanical properties for both, aged and unaged cured rubbers. Increasing the amount of diene monomer in EPDM structure was beneficial for phenolic rubber cure system. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46213.     

The effect of mercapto‐modified ethylene–vinyl acetate (EVA) on curing parameters,mechanical properties,and thermal properties of vulcanized styrene–butadiene rubber (SBR)/EVA blends

The effect of EVA functionalized with mercapto groups (EVALSH) on the compatibilization of SBR and EVA copolymer blends was investigated in vulcanized systems based on sulfur or dicumyl peroxide (DCP). The presence of EVALSH resulted in an improvement of the tensile properties, indicating the reactive compatibilizing effect of this compound. The best mechanical performance was achieved with the sulfur‐curing system for both compatibilized and noncompatibilized blends. The blend systems were also analyzed by scanning electron microscopy, differential scanning calorimetry, and dynamic‐mechanical analysis. The crystallinity of the EVA phase was significantly affected by the presence of the EVALSH, whereas no substantial change was detected on the damping properties or the glass transition temperature of the SBR phase. Considering the aging properties, the presence of EVALSH increases the thermal stability of the blends vulcanized with DCP. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 239–249, 2002     

Acrylic rubber‐fluorocarbon rubber miscible blends: Effect of curatives and fillers on cure,mechanical, aging,and swelling properties

The cure characteristics and mechanical properties of gum and filled acrylic rubber (ACM), fluorocarbon rubber (FKM), and their blends of varying compositions were studied both under unaged and aged conditions. The rheometric study showed that optimum cure properties were obtained using a mixed curing system of blocked diamine, hexamethylenediamine carbamate (Diak #1), and ammonium benzoate. From varying the curing agents, the optimum levels of Diak #1 and ammonium benzoate were found to be 1.5 and 2.5 phr, respectively. The addition of different fillers and their loading influenced the cure properties, with increased torque and reduced scorch safety. The gum and filled 50:50 (w/w) ACM‐FKM showed overall performance in strength properties. Postcuring improved the strength of all the systems, especially the systems with a higher proportion of FKM. None of the properties changed significantly during aging of the blends. FKM and the blends containing a higher proportion of FKM were affected least by aging. Swelling of the blends was reduced by the addition of fillers. Dynamic mechanical thermal analysis showed a single tan δ peak corresponding to a single phase transition for both cured and filled blends. The storage modulus of the blend increased from the gum blend to the filled blend, indicating the presence of polymer‐filler interaction. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1442–1452, 2003     

Reactive compatibilization of the poly(butylene terephthalate)–EVA blend by maleic anhydride. II. Correlations among gel contents,grafting yields,and mechanical properties

Correlations among the degree of crosslinking of ethylene vinyl acetate copolymer (EVA), the grafting yield of maleic anhydride (MAH) onto EVA, and the mechanical properties of the blends of poly(butylene terephtalate) (PBT) with EVA‐g‐MAH were investigated. The EVA was functionalized by melt grafting reaction in the presence of MAH and dicumyl peroxide (DCP) using a plasticorder. The grafting yield of MAH was increased by increasing the concentration of MAH and DCP. The flexural strength of PBT–EVA‐g‐MAH blends depends on both the grafting yield of MAH and the degree of crosslinking of EVA, while the crosslinked parts of EVA‐g‐MAH hindered rather than improved the tensile strength regardless of the increase of the grafting yield of MAH. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1305–1310, 2003     

Tensile properties and morphology of the dynamically cured EPDM and PP/HDPE ternary blends

The tensile properties and morphology of the polyolefin ternary blends of ethylenepropylene–diene terpolymer (EPDM), polypropylene and high density polyethylene were studied. Blends were prepared in a laboratory internal mixer where EPDM was cured in the presence of PP and HDPE under shear with dicumyl peroxide (DCP). For comparison, blends were also prepared from EPDM which was dynamically cured alone and blended with PP and HDPE later (cure–blend). The effect of DCP concentration, intensity of the shear mixing, and rubber/plastics composition was studied. The tensile strength and modulus increased with increasing DCP concentration in the blends of EPDM-rich compositions but decreased with increasing DCP concentration in blends of PP-rich compositions. In the morphological analysis by scanning electron microscopy (SEM), the small amount of EPDM acted as a compatibilizer to HDPE and PP. It was also revealed that the dynamic curing process could reduce the domain size of the crosslinked EPDM phase. When the EPDM forms the matrix, the phase separation effect becomes dominant between the EPDM matrix and PP or HDPE domain due to the crosslinking in the matrix.     

Cure characteristics and mechanical properties of hydrogenated natural rubber/natural rubber blends

The cure characteristics and mechanical properties of blends consisting of hydrogenated natural rubber (HNR) and natural rubber (NR) blends were investigated. The HNR/NR blends at 50/50 wt ratio were vulcanized using various cure systems: peroxide vulcanization, conventional vulcanization with peroxide, and efficient vulcanization with peroxide. The HNR/NR vulcanizates cured by the combination of peroxide and sulfur donor (tetramethylthiuram disulfide, TMTD) in the efficient vulcanization with peroxide exhibited the best mechanical properties. It was also found that the hydrogenation level of HNR did not affect the tensile strength of the vulcanizates. The tensile strength of the blends decreased with increasing HNR content because of the higher incompatibility to cause the noncoherency behavior between NR and HNR. However, the HNR/NR vulcanizate at 50/50 wt ratio showed the maximum ultimate elongation corresponding to a co‐continuous morphology as attested to by scanning electron micrographs. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Cure characteristics and mechanical properties of styrene-butadiene rubber/hydrogenated acrylonitrile-butadiene rubber/silica composites

Composites of styrene butadiene rubber (SBR), hydrogenated acrylonitrile–butadiene rubber (HNBR) and silica were prepared. Sulfur (S), dicumyl peroxide (DCP) and a combination of S and DCP (M) were used as curing agents, respectively. The morphology of the composites with different blend ratio was examined to correlate with observations on mechanical properties by scanning electron microscopy. The effects of blend ratio and curing systems on the curing characteristics and mechanical properties, such as stress–strain behavior, tensile strength, elongation at break and hardness of SBR/HNBR/Silica composites, were studied. Composites prepared by M curing systems showed comparatively better mechanical properties, wet traction and rolling resistance than S and D curing systems. The tensile strength, tear strength, and elongation at break were improved by adding HNBR for M curing systems. The wet traction of the vulcanizates containing HNBR was better than that of the vulcanizates without HNBR. A relatively uniform dispersion of silica was observed for SBR/HNBR/silica compositions compared with SBR/silica composites.     

The effect of curing system on the properties of the thermoplastic elastomer foams of ethylene‐vinyl acetate copolymer and styrene‐butadiene and ethylene‐propylene‐diene monomer rubbers

Thermoplastic elastomer (TPE) foams have important application in electrical, toys, and other industries. Several foams were prepared by ethylene‐vinyl acetate copolymer (EVA) lonely, and in combination with styrene‐butadiene and ethylene‐propylene‐diene monomer rubbers (SBR and EPDM). The effects of crosslinking and foaming agents and EVA type on density and mechanical properties of the cured foams with two curing systems, peroxide and sulfur‐peroxide with potential use in automotive applications, were studied. The results showed that proposed compounds formulations were foamed properly. The viscosity of the EVA was a key factor for the density values of the formed foams. The densities of the cured foams with peroxide system with various SBR contents were higher when compared with cured foams with sulfur‐peroxide system. With increasing foaming agent, the densities of the foams were reduced for studied curing systems. The densities of the EVA–EPDM foams were lower than those of the EVA–SBR foams in the same studied conditions. Increasing rubber in foam formulation had adverse effect on tensile properties of the foams. The existence of the talc powder in foam formulation had important role on the shape and type of the formed cells and resulted in foams with mostly closed cells. The results of this study help the automotive article designer to produce suitable TPE foam. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45357.     

Dynamically vulcanized polypropylene/styrene–butadiene rubber blends: The effect of a peroxide/bismaleimide curing system and composition

Polypropylene (PP)/styrene–butadiene rubber blends were studied with special attention given to the effects of the blend ratio and dynamic vulcanization. Dicumyl peroxide (DCP) was used as the curing agent in combination with N,N′‐m‐phenylene bismaleimide (BMI) as the coagent for the curing process. Outstanding mechanical performance, especially with regard to the elongation at break, and better resistance to compression set were achieved with the dynamic vulcanization; this indicated that the DCP/BMI system also acted as a compatibilizing agent. This phenomenon was also confirmed by Fourier transform infrared spectroscopy of the insoluble material, the crystallinity degree of the PP phase (as investigated by X‐ray diffractometry), and scanning electron microscopy. The dynamic mechanical properties of the nonvulcanized and vulcanized blends were also investigated. The aging resistance of the blends was also evaluated. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Ethylene vinyl acetate as compatibilizer on cure characteristics and mechanical properties of (natural rubber)/(Recycled acrylonitrile‐butadiene rubber) blends

Ethylene vinyl acetate (EVA) has been used as a compatibilizer for (natural rubber)/(recycled acrylonitrile‐butadiene rubber) (NR/NBRr) blends, vulcanized by sulfur. EVA offers excellent heat, ozone, and weather resistance, whereas the vinyl acetate groups provide oil resistance to the blend. It exhibits good tear resistance and may be crosslinked. However, EVA exhibits poor low‐temperature flexibility. NBR gloves have excellent resistance to punctures, tears, and many types of chemicals, while NR has good physical and mechanical properties. NR/NBRr blends were prepared with various compositions with the EVA content fixed. Tensile properties, hardness, and swelling behavior tests were performed to determine the compatibility of NR/NBRr blends in the presence of EVA. Results indicated that incorporation of EVA into NR/NBRr blends improved tensile strength, modulus, and elongation at break compared with NR/NBRr blends without EVA. The improvement in hardness and reduction in resilience on compatibilization are due to an increase in crosslink density, which gives NR/NBRr blends better swelling resistance. Scanning electron microscopy of the fracture surfaces indicates that, with the addition of EVA in NR/NBRr blends, better adhesion between NR and NBRr was obtained, thus improving the compatibility of NR/NBRr blends. J. VINYL ADDIT. TECHNOL., 23:135–141, 2017. © 2015 Society of Plastics Engineers     

Effect of dicumyl peroxide and phenolic resin as a mixed curing system on the mechanical properties and morphology of TPVs based on HDPE/ground tire rubber

Thermoplastic vulcanizates (TPVs) are a special group of thermoplastic elastomer with the characteristic that consists of rubber elasticity and the processability of thermoplastic polymers. TPVs based on high density polyethylene (HDPE)/ground tire rubber (GTR) with phenolic resin (HY‐2045) and dicumyl peroxide (DCP) as vulcanizing agents are prepared through dynamic vulcanization in this article. The blends consisting of 40/60 HDPE/GTR are melt‐mixed in an internal mixer and then pressed with a compression molding machine. The aim of this experiment is to study the influence of a compound curing agent system on the mechanical properties of the HDPE/GTR composites. The results indicate that the mechanical properties of the HDPE/GTR blends are improved significantly by adding 4 phr HY‐2045 and 0.3 phr DCP than those of TPVs without any vulcanizing agents after dynamic vulcanization. The X‐ray photoelectron spectroscopy study and the FTIR‐ATR analysis confirmed that the crosslinking phenomenon occurred in the preparation of TPVs; and the gel fraction analysis indicates that the GTR components and the HDPE components of the HDPE/GTR blends are all moderately crosslinked. In addition, the morphology of the HDPE/GTR blends has been investigated by scanning electron microscopy. POLYM. COMPOS., 36:1907–1916, 2015. © 2014 Society of Plastics Engineers     

Curing characteristics,morphology, thermal stability,mechanical properties,and irradiation resistance of methylethylsilicone/methylphenylsilicone rubber blends

Methylethylsilicone rubber (MESR)/methylphenylsilicone rubber (MPSR) blends were cured with 2,5‐dimethyl‐2,5‐di(tert‐butylperoxy)hexane. The curing characteristics, morphology, thermal behaviors, mechanical properties at different temperatures, radiation resistance, and thermal aging resistance of the MESR/MPSR blends were investigated. The results show that a high MPSR content could decrease the optimum curing time and improve the scorch safety. Dynamic mechanical analysis revealed that the glass‐transition temperature of the blends increased slightly with the addition of MPSR. Scanning electron microscopy showed that MESR and MPSR had good compatibility in the blends. Thermogravimetric analysis indicated that the thermal stability of the blends increased with increasing quantity of MPSR. The blends had excellent mechanical properties at low temperatures. However, these properties were significantly reduced when the temperature was increased. Moreover, changes in the mechanical properties decreased with increasing MPSR content at high temperatures, especially at temperatures higher than 100°C. In addition, the radiation resistance and thermal aging resistance of the blends increased with increasing MPSR content. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40529.