Preparation and performance characteristics of short‐glass‐fiber/maleated styrene–ethylene–butylene–styrene/polypropylene hybrid composites

Eighty/twenty polypropylene (PP)/styrene–ethylene–butylene–styrene (SEBS) and 80/20 PP/maleated styrene–ethylene–butylene–styrene (SEBS‐g‐MA) blends reinforced with 30 wt % short glass fibers (SGFs) were prepared by extrusion and subsequent injection molding. The influence of the maleic anhydride (MA) functional group grafted to SEBS on the properties of SGF/SEBS/PP hybrid composites was studied. Tensile and impact tests showed that the SEBS‐g‐MA copolymer improved the yield strength and impact toughness of the hybrid composites. Extensive plastic deformation occurred at the matrix interface layer next to the fibers of the SGF/SEBS‐g‐MA/PP composites during impact testing. This was attributed to the MA functional group, which enhanced the adhesion between SEBS and SGF. Differential scanning calorimetry measurements indicated that SEBS promoted the crystallization of PP spherulites by acting as active nucleation sites. However, the MA functional group grafted to SEBS retarded the crystallization of PP. Finally, polarized optical microscopy observations confirmed the absence of transcrystallinity at the glass‐fiber surfaces of both SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrid composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1303–1311, 2002     

Preparation and properties of styrene–ethylene–butylene–styrene block copolymer/clay nanocomposites: I. Effect of clay content and compatibilizer types

BACKGROUND: Polymer/clay (silicate) systems exhibit great promise for industrial applications due to their ability to display synergistically advanced properties with relatively small amounts of clay loads. The effects of various compatibilizers on styrene–ethylene–butylene–styrene block copolymer (SEBS)/clay nanocomposites with various amounts of clay using a melt mixing process are investigated. RESULTS: SEBS/clay nanocomposites were prepared via melt mixing. Two types of maleated compatibilizers, styrene–ethylene–butylene–styrene block copolymer grafted maleic anhydride (SEBS‐g‐MA) and polypropylene grafted maleic anhydride (PP‐g‐MA), were incorporated to improve the dispersion of various amounts of commercial organoclay (denoted as 20A). Experimental samples were analyzed using X‐ray diffraction and transmission electron microscopy. Thermal stability was enhanced through the addition of clay with or without compatibilizers. The dynamic mechanical properties and rheological properties indicated enhanced interaction for the compatibilized nanocomposites. In particular, the PP‐g‐MA compatibilized system conferred higher tensile strength or Young's modulus than the SEBS‐g‐MA compatibilized system, although SEBS‐g‐MA seemed to further expand the interlayer spacing of the clay compared with PP‐g‐MA. CONCLUSION: These unusual results suggest that the matrix properties and compatibilizer types are crucial factors in attaining the best mechanical property performance at a specific clay content. Copyright © 2007 Society of Chemical Industry     

Rheological behaviors of glass bead‐ and wollastonite‐filled polypropylene composites modified with thermoplastic elastomers

Steady‐ and oscillatory‐shear rheological behaviors of polypropylene/glass bead (PP/GB) and PP/wollastonite (PP/W) melts modified with thermoplastic elastomers, poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and the corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were examined by means of a parallel‐plate rheometer. With adding the elastomers (SEBS and SEBS‐g‐MA) and fillers (spherical GB and acicular W) to PP, viscosity especially at low shear rates and shear‐thinning flow behavior at high shear rates were pronounced as evidenced quantitatively by Carreau–Yasuda (CY) parameters, but Cox–Merz analogy became weakened. Besides, melt‐elasticity in terminal region and relaxation time (t_c) in crossing point increased, indicating an enhancement in quasi‐solid behavior of molten PP. Comparing with the elastomers, rheological behaviors of molten PP were more influenced with adding the rigid fillers, especially with W due to distinct acicular shape of W particles. SEBS‐g‐MA elastomer more affected rheological behaviors of the ternary composites than SEBS elastomer, implying that SEBS elastomer and the filler particles behaved individually (i.e., development of separate microstructure) in (PP/GB)/SEBS and (PP/W)/SEBS ternary composites, but core‐shell microstructure developed with strong interfacial adhesion by adding SEBS‐g‐MA elastomer, and the filler particles encapsulated with the thick SEBS‐g‐MA elastomer interlayer (i.e., core‐shell particles) acted like neither big elastomer particles nor like individual rigid particles in melt‐state. Moreover, effects of SEBS‐g‐MA elastomer reached a maximum on rheological behaviors of (PP/W)/SEBS‐g‐MA ternary composite, indicating a synergy between core‐shell microstructure and acicular W particles. Correlations between oscillatory‐shear flow properties and microstructures of the blends and composites were evaluated using Cole–Cole (CC), Han–Chuang (HC), and van Gurp–Palmen (vGP) plots. COMPOS., 2012. © 2012 Society of Plastics     

Microstructural characteristics of glass bead‐ and wollastonite‐filled isotactic‐polypropylene composites modified with thermoplastic elastomers

Microstructural characteristics of isotactic‐polypropylene/glass bead (iPP/GB) and iPP/wollastonite (iPP/W) composites modified with thermoplastic elastomers, poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were investigated. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and dynamic mechanical analyses (DMA) showed that the iPP/SEBS and iPP/SEBS‐g‐MA blends were partially compatible two‐phase systems. Well‐dispersed spherical GB and acicular W particles without evidence of interfacial adhesion were observed in the iPP/GB and iPP/W binary composites respectively. Contrary to the blends, melt flow rates of the iPP/GB and PP/W composites decreased more with SEBS‐g‐MA than with SEBS because of enhanced interfacial adhesion with SEBS‐g‐MA elastomer. The SEM analyses showed that the ternary composites containing SEBS exhibited separate dispersion of the rigid filler and elastomer particles (i.e., separate microstructure). However, SEBS‐g‐MA elastomer not only encapsulated the spherical GB and acicular W particles completely with strong interfacial adhesion (i.e., core‐shell microstructure) but also dispersed separately throughout iPP matrix. In accordance with the SEM observations, the DSC and DMA revealed quantitatively that the rigid filler and SEBS particles in iPP matrix acted individually, whereas the rigid filler particles in the ternary composites containing SEBS‐g‐MA acted like elastomer particles because of the thick elastomer interlayer around the filler particles. The Fourier transform infrared analyses revealed an esterification reaction inducing the strong interfacial adhesion between the SEBS‐g‐MA phase and the filler particles. POLYM. COMPOS., 31:1265–1284, 2010. © 2009 Society of Plastics Engineers     

Influences of compatibilizers on rheology and mechanical properties of propylene random copolymer/styrene‐ethylene‐butylene‐styrene block copolymer/organic‐montmorillonite nanocomposites

Propylene random copolymer (PPR)/styrene‐ethylene‐butylene‐styrene block copolymer (SEBS)/compatibilizer/organic‐montmorillonite (OMMT) quaternary nanocomposites and PPR/compatibilizer/OMMT ternary nanocomposites were prepared via two‐stage melt blending and influences of compatibilizers, maleic anhydride (MA) grafted styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA), poly(octene‐co‐ethylene) (POE‐g‐MA), or propylene block copolymers (PPB‐g‐MA), on rheology and mechanical properties of the nanocomposites were investigated. The results of X‐ray diffraction measurement and transmission electron microscopy observation showed that OMMT layers were mainly intercalated in the nanocomposites except for the mainly exfoliated structure in the quaternary nanocomposites using POE‐g‐MA as compatibilizer. The nanocomposites exhibited pseudo‐solid like viscoelasticity in low frequencies and shear‐thinning in high shear rates. As far as OMMT dispersion was concerned, POE‐g‐MA was superior to SEBS‐g‐MA and PPB‐g‐MA, which gives rise to the highest viscosities in both the ternary and quaternary nanocomposites. The quaternary nanocomposites containing POE‐g‐MA were endowed with balanced toughness and rigidity. It was suggested that a suitable combination of compatibilizer and SEBS was an essentially important factor for adjusting the OMMT dispersion and distribution, the rheological and mechanical performances of the nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Process–structure–property relationship in ternary short‐glass‐fiber/elastomer/polypropylene composites

Short‐glass‐fiber (SGF)‐reinforced polypropylene (PP) composites toughened with a styrene/ethylene butylene/styrene (SEBS) triblock copolymer were injection molded after extrusion. Furthermore, a maleic anhydride (MA)‐grafted SEBS copolymer (SEBS‐g‐MA) was used as an impact modifier and compatibilizer. The effects of the processing conditions and compatibilizer on the microstructure and tensile and impact performance of the hybrid composites were investigated. In the route 1 fabrication process, SGF, PP, and SEBS were blended in an extruder twice, and this was followed by injection molding. In route 2, or the sequential blending process, the elastomer and PP were mixed thoroughly before the addition of SGF. In other words, either PP and SEBS or PP and SEBS‐g‐MA pellets were premixed in an extruder. The produced pellets were then blended with SGF in the extruder, and this was followed by injection molding. The SGF/SEBS‐g‐MA/PP hybrid fabricated by the route 2 process exhibited the highest modulus, yield stress, tensile stress at break, Izod impact energy, and Charpy drop weight impact strength among the composites investigated. This was due to the formation of a homogeneous SEBS elastomeric interlayer at the SGF and matrix interface of the SGF/SEBS‐g‐MA/PP hybrid. This SEBS rubbery layer enhanced the interfacial bonding between SGF and the matrix of the SGF/SEBS‐g‐MA/PP hybrid. The correlations between the processing, microstructure, and properties of the hybrids were investigated. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1384–1392, 2003     

Tensile deformation mechanisms of polypropylene/elastomer blends reinforced with short glass fiber

Polypropylene hybrid composites reinforced with short glass fiber (SGF) and toughened with styrene–ethylene butylenes–styrene (SEBS) elastomer were prepared using extrusion and injection‐molding techniques. Moreover, hybrids compatibilized with SEBS‐grafted maleic anhydride (SEBS‐g‐MA) and hybrid compatibilized with PP grafted with maleic anhydride (PP‐g‐MA) were also fabricated. The matrix of the latter hybrid was designated as mPP and consisted of 95% PP and 5% PP‐g‐MA. Tensile dilatometry was carried out to characterize the fracture mechanisms of hybrid composites. Dilatometric responses showed that the elastic deformation was the dominant deformation mechanism for the SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrids. However, cavitation deformation prevailed over shearing deformation for both hybrids at the higher strain regime. The cavitation strain resulted from the debonding of glass fibers and from the crazing of the matrix in the SGF/SEBS/PP hybrid. In contrast, the cavitation was caused by the debonding of SEBS particles from the matrix of the SGF/SEBS‐g‐MA/PP hybrid. The use of PP‐g‐MA resulting in elastic deformation was the main mode of deformation in the low‐strain region for the SGF/SEBS/mPP and SEBS/SEBS‐g‐MA/mPP hybrids; thereafter, shearing appeared to dominate at the higher strain regime. This was attributed to the MA functional group improving the bonding between the SGF and PP. The correlation between fracture morphology and dilatometric responses also is presented in the article. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 441–451, 2003     

A compatibilized composite of recycled polypropylene filled with cellulosic fiber from recycled corrugated paper board: Mechanical properties,morphology, and thermal behavior

This article deals with the feasibility of using recycled corrugated paper board (rPF) as the reinforcing material for recycled plastics. The composites of recycled polypropylene (rPP) and rPF were prepared by extrusion compounding and injection molding, and the rPP/rPF composites compatibilized by maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted ethylene‐1‐octene copolymer (POE‐g‐MA), and maleic anhydride grafted styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA) were also prepared. The crystallization and melting behavior, mechanical properties, thermal stability, and morphology of these composites were studied. The results indicated that rPF promoted the crystallization, enhanced the strength and toughness of rPP/rPF composites to some extent while decreased thermal stability at the same time. PP‐g‐MA and POE‐g‐MA improved the dispersion and interface adhesion of rPF, and further upgraded the mechanical properties and vicat softening temperatures. Among these compatibilizers, PP‐g‐MA was most favorable to the strength improvement while POE‐g‐MA was most favorable to the toughness improvement. As for SEBS‐g‐MA, it had no obvious modification effect. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Drop weight impact and work of fracture of short glass fiber reinforced polypropylene composites toughened with elastomer

Short glass fiber (SGF) reinforced polypropylene composites toughened with styrene‐ethylene butylene‐styrene (SEBS) or maleated SEBS (SEBS‐g‐MA) triblock copolymer were injection molded. Charpy drop‐weight impact properties and the impact essential work of fracture (EWF) of the SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrids were investigated. Drop‐weight impact results revealed that the SGF/SEBS/PP hybrid exhibits higher impact strength than the SGF/SEBS‐g‐MA/PP hybrid at low impact speeds. This was derived from the pull‐out of fibers from the SGF/SEBS/PP hybrid. At high impact speeds, the impact strength of the SGF/SEBS‐g‐MA/PP hybrid was slightly higher than that of the SGF/SEBS/PP hybrid. Impact EWF measurements showed that the hybrids only exhibit specific essential work (W_e) at a high impact speed of 3 ms⁻¹. The non‐essential work does not occur in the hybrids under high impact rate loading conditions. Moreover, SEBS or SEBS‐g‐MA addition was beneficial in enhancing the high‐rate specific essential work of the SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrid composites.     

Effects of silane coupling agent and maleic anhydride‐grafted polypropylene on the morphology and viscoelastic properties of polypropylene–mica composites

In this study, morphology, and dynamic and mechanical properties of polypropylene–mica (PP–Mica) composites were investigated. To enhance the adhesion between PP and mica, maleic anhydride‐grafted PP (MAPP) and treated mica with silane coupling agent were used. MAPP (as a compatibilizer) and silane coupling agent (as a filler surface modifier) caused an interfacial bonding in the mica filled polypropylene composites. The effect of mica content, MAPP, and treated mica with silane coupling agent on the morphological properties were investigated by Scanning Electron Microscopy (SEM). The results showed that with increasing MAPP or silane coupling agent, dispersion of filler and adhesion between PP and filler were improved. Mechanical data showed that with increasing MAPP and mica treated with silane coupling agent, tensile modulus and flextural strength of composites were enhanced. Dynamic rheological behavior of composites was also investigated within the domain of linear viscoelasticity. The rheological observations indicated that the complex viscosity, storage and loss moduli increased, and tan δ decreased with increasing mica content. POLYM. COMPOS. 27:491–496, 2006. © 2006 Society of Plastics Engineers.     

Effects of compatibilizers and testing speeds on the mechanical properties of organophilic montmorillonite filled polyamide 6/polypropylene nanocomposites

In the present study, the fracture properties of different types of organophilic montmorillonite (OMMT) filled polyamide 6/polypropylene nanocomposites was investigated. Two types of compatibilizers, i.e., maleic anhydride grafted polypropylene (PP‐g‐MA) and maleic anhydride grafted styrene‐ethylene/butylene‐styrene (SEBS‐g‐MA) were used to compatibilize these systems. The tensile properties were studied through tensile test at two different testing speeds; 50 and 500 mm/min whereas the fracture properties were determined using single‐edge‐notch‐3 point‐bending (SEN‐3PB) specimens at three different testing speeds; 1, 100, and 500 mm/min. The presence of both PP‐g‐MA and SEBS‐g‐MA compatibilizers improved the tensile and fracture properties of nanocomposites due to the compatibilizing effect of both compatibilizers. SEBS‐g‐MA compatibilizer seemed to be more effective in improving the fracture toughness of nanocomposites than PP‐g‐MA especially at high testing speed. This was due to the elastomeric nature of SEBS‐g‐MA, which can provide a better toughening effect than the relatively harder PP‐g‐MA. POLYM. ENG. SCI., 50:1493–1504, 2010. © 2010 Society of Plastics Engineers     

Tribological behavior of polyamide 66‐based binary and ternary composites

Friction and wear characteristics of polyamide 66 (PA66) and the composites of organoclay modified by styrene–ethylene/butylene–styrene triblock copolymer grafted with 1.84 wt% of maleic anhydride (SEBS‐g‐MA) were studied using an Universal Micro Tribometer reciprocating friction and wear tester. The morphologies of the wear tracks of PA66 and the composites were observed using a scanning electron microscope. The results showed that plastic deformation induced by the traction of the harder steel ball occurred on the worn surfaces of PA66 and the composite which were reinforced by SEBS‐g‐MA copolymer. It was found that the average frictional coefficient and specific wear rate of PA66/SEBS‐g‐MA binary composite are lowest under the same conditions. This indicates that toughness and wear resistance of PA66 matrix are improved with the incorporation of SEBS‐g‐MA copolymer. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Effects of carbon nanofibers on the fracture,mechanical, and thermal properties of PP/SEBS‐g‐MA blends

Polypropylene/maleated (styrene‐ethylene‐butadiene‐styrene) (PP/SEBS‐g‐MA) blends reinforced with 0.2–2.5 wt% carbon nanofibers (CNFs) were prepared by injection molding. The structure, thermal, mechanical, and fracture behaviors of PP/SEBS‐g‐MA blends and their nanocomposites were studied. Wide‐angle X‐ray diffraction (WAXD) results showed that the SEBS‐g‐MA and/or CNF additions do not induce a structural change of PP. Tensile measurements showed that the Young's modulus and tensile yield strength increase with the increasing filler content. Izod impact and essential work of fracture test results demonstrated that CNFs are beneficial to improve the impact strength and specific essential work of fracture of PP/SEBS‐g‐MA blends. Therefore, tough PP‐nanocomposites can be achieved by melt‐blending low fractions of CNFs and appropriate elastomer contents. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Effect of fiber pretreatment condition on the interfacial strength and mechanical properties of wood fiber/PP composites

The effect of fiber surface pretreatment on the interfacial strength and mechanical properties of wood fiber/polypropylene (WF/PP) composites are investigated. The results demonstrate that fiber surface conditions significantly influence the fiber–matrix interfacial bond, which, in turn, determines the mechanical properties of the composites. The WF/PP composite containing fibers pretreated with an acid–silane aqueous solution exhibits the highest tensile properties among the materials studied. This observation is a direct result of the strong interfacial bond caused by the acid/water condition used in the fiber pretreatment. Evidence from coupling chemistry, rheological and electron microscopic studies support the above conclusion. When SEBS‐g‐MA copolymer is used, a synergistic toughening effect between the wood fiber and the copolymer is observed. The V‐notch Charpy impact strength of the WF/PP/SEBS‐g‐MA composite is substantially higher than that of the WF/PP composite. The synergistic toughening mechanisms are discussed with respect to the interfacial bond strength, fiber‐matrix debonding, and matrix plastic deformation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1000–1010, 2000     

Influence of addition of styrene–ethylene/butylene–styrene copolymer on rheological,mechanical, and tribological properties of polyamide nanocomposites

To develop new tribomaterials for mechanical sliding parts, investigations were carried out on the influence of adding styrene–ethylene/butylene–styrene block copolymer (SEBS) on the rheological, mechanical, and tribological properties of polyamide 6 (PA6) nanocomposite, which is a commercial product of layered silicate (clay) filled polyamide 6 (PA6/Clay). Two kinds of block copolymers, unmodified SEBS (SEBS) and maleic anhydride‐grafted SEBS (SEBS‐g‐MA), were added with PA6/Clay nanocomposite. Dynamic viscoelastic properties in the molten state of these nanocomposites and their tensile, impact, and tribological properties of these nanocomposites were evaluated. Dynamic viscoelastic properties were found to increase with the addition of SEBS and were influenced, in particular, by block copolymers containing SEBS‐g‐MA. Influence of the addition of SEBS on mechanical properties of these systems differed for each mechanical property. Although tensile properties decreased with SEBS, Izod impact properties were improved with the addition of SEBS‐g‐MA. Tribological properties were improved with the addition of block copolymer, and the influence of the amount of addition was higher than the type of block copolymer used. These results indicate that new tribomaterials developed have sufficient balance amongst moldability, mechanical, and tribological properties. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Rice husk powder–filled polystyrene/styrene butadiene rubber blends

Natural fibers are rich in cellulose and they are a cheap, easily renewable source of fibers with the potential for polymer reinforcement. The presence of large amounts of hydroxyl groups makes natural fibers less attractive for reinforcement of polymeric materials. Composites made from polystyrene (PS)/styrene butadiene rubber (SBR) blend and treated rice husk powder (RHP) were prepared. The RHP was treated by esterification and acetylation. A similar series of composites was also prepared using maleic anhydride–polypropylene (MA–PP) as a coupling agent. The processing behavior, mechanical properties, effect of thermooxidative ageing, and surface morphology of untreated and chemically modified RHP were studied. There was a decrease in tensile strength (except MA–PP composites), elongation at break, and Young's modulus in chemically treated RHP composites. The postreaction process during thermooxidative ageing enhanced the tensile strength and Young's modulus of the esterified and MA–PP composites. Acetylation treatment was effective in reducing the percentage of water absorption in RHP/PS–SBR composites. In general chemically treated RHP/PS–SBR composites and MA–PP showed a better matrix phase and filler distribution. However, the degree of filler–matrix interaction was mainly responsible for the improvement of mechanical properties in the composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3320–3332, 2004     

Mechanical properties of wollastonite‐reinforced polypropylene composites modified with SEBS and SEBS‐g‐MA elastomers

Mechanical properties of isotactic polypropylene/wollastonite/styrene rubber block copolymers (iPP/wollastonite/SRBC) composites were studied as a function of elastomeric poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) triblock copolymer (SEBS) and SEBS grafted with maleic anhydride (SEBS‐g‐MA) content from 0 to 20 vol%. Microphase morphology was stronger influenced by SRBC elastomers than by different wollastonite types. Higher encapsulation ability of SEBS‐g‐MA than SEBS caused more expressive core‐shell morphology and consequently higher notched impact strength as well as yield parameters, but lower Young's modulus. Higher ductility of the composites with SEBS than with SEBS‐g‐MA has been primarily caused by better miscibility of the polypropylene chains with SEBS molecules. Surface properties of components and adhesion parameters also indicated that adhesion at SEBS‐g‐MA/wollastonite interface, which was stronger than the one at the SEBS/wollastonite interface, influenced higher encapsulation of wollastonite particles by SEBS‐g‐MA. POLYM. ENG. SCI., 47:1873–1880, 2007. © 2007 Society of Plastics Engineers     

SBS and SEBS block copolymers as impact modifiers for polypropylene compounds

Blends of polypropylene (PP) and thermoplastic elastomers (TPE), namely SBS (styrene‐butadiene‐styrene) and SEBS (styrene‐ethylene/1‐butene‐styrene) block copolymers, were prepared to evaluate the effectiveness of the TPE type as an impact modifier for PP and influence of the concentration of elastomer on the polymer properties. Polypropylene homopolymer (PP‐H) and ethylene–propylene random copolymer (PP‐R) were evaluated as the PP matrix. Results showed that TPEs had a nucleating effect that caused the PP crystallization temperature to increase, with SBS being more effective than SEBS. Microstructure characterization tests showed that in most cases PP/SEBS blends showed the smallest rubber droplets regardless of the matrix used. It was seen that SEBS is a more effective toughening agent for PP than SBS. At 0°C the Izod impact strength of the PP‐H/SEBS 30% b/w blend was twofold higher than the SBS strength, with the PP‐R/SEBS 30% b/w blend showing no break. A similar behavior on tensile properties and flexural modulus were observed in both PP/TPE blends. Yield stress and tensile strength decreased and elongation at break increased by expanding the dispersed elastomeric phase in the PP matrix. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 254–263, 2005     

Effect of a silane coupling agent on the properties of white rice husk ash–polypropylene/natural rubber composites

White rice husk ash (WRHA)–polypropylene (PP)/natural rubber (NR) composites were prepared using a Brabender Plasticorder at 180 °C and a rotor speed of 50 rev min^?1. The mechanical and water‐absorption properties were studied. The incorporation of WRHA into the PP/NR matrix has resulted in the improvement of the tensile modulus; however, the tensile strength, elongation at break and stress at yield decreased with increasing WRHA loading. Poor filler matrix interactions are believed to be responsible for the decrease in the properties. Incorporation of a silane coupling agent, 3‐aminopropyl triethoxysilane (3‐APE), improved tensile modulus, tensile strength and stress at yield of the composites. Water‐absorption studies indicate that the use of the coupling agent reduced the amount of water absorbed by the composites. © 2001 Society of Chemical Industry     

Mechanical properties of glass bead‐ and wollastonite‐filled isotactic‐polypropylene composites modified with thermoplastic elastomers

Mechanical properties of the isotactic‐polypropylene/glass bead (iPP/GB) and iPP/wollastonite (iPP/W) composites modified with thermoplastic elastomers, the poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were investigated. An increase in toughness of iPP with the elastomers was associated with a decrease in rigidity and strength. Mechanical performance of iPP increased more with acicular W than with spherical GB due to reinforcing effect of W. Comparing the (iPP/GB)/SEBS and (iPP/W)/SEBS composites having the separate microstructure, strength and toughness values of the iPP/GB and iPP/W composites increased more with SEBS‐g‐MA at the expense of rigidity due to the core‐shell microstructure with strong interfacial adhesion. Moreover, the iPP/W composite exhibited superior mechanical performance with 2.5 and 5 vol% of SEBS‐g‐MA because of a positive synergy between the core‐shell microstructure and reinforcing effect of acicular W. The extended models revealed that the elastomer and filler particles in the (iPP/GB)/SEBS and (iPP/W)/SEBS composites acted individually due to the separate microstructure. However, the rigid GB and W particles encapsulated with the thick elastomer interlayer (R₀/R₁ = 0.91) in the (iPP/GB)/SEBS‐g‐MA and (iPP/W)/SEBS‐g‐MA composites acted like neither big elastomer particles nor like individual rigid particles, inferring more complicated failure mechanisms in the core‐shell composites. POLYM. COMPOS., 31:1285–1308, 2010. © 2010 Society of Plastics Engineers