Interacting Blends of Novel Acrylated Poly(Ester Amide)s Based on DGEBC with Styrene Monomer

Bisphthalamic acids were prepared by reaction of phthalic anhydride and aromatic diamines. Novel poly(ester amide) resins (PEAs) were prepared by reaction between diglycidyl ether of bisphenol-C with bisphthalamic acids using a base catalyst. Post reactions of all these PEAs were carried out with acryloyl chloride. The resultant products are designated as acrylated poly(ester amide) resins (APEAs). The PEAs and APEAs were characterized by elemental analysis and number average molecular weight determined by nonaqueous conductometric titration method. IR spectra of PEAs and APEAs were also recorded. Blending of these APEAs with styrene monomer were carried out. The curing of these APEAs-styrene blends was monitored on a differential scanning calorimeter (DSC) by using benzoyl peroxide as a catalyst. Based on DSC data, glass fiber-reinforced composites of APEAs-styrene blends have been fabricated and their chemical, mechanical and electrical properties have been evaluated. Unreinforced cured samples of APEAs-styrene blends were analyzed thermogravimetrically.     

Novel Interacting Blends of Unsaturated Polyester-s-Triazine and Epoxy Resin

2-(4-ethyl-1-piperazinylo)-4,6-bismaleatedethylamino-1,3,5-triazine (EBT) was prepared by the reaction of 2-(4-ethyl-1-piperazinylo)-4,6-bishydroxyethylamino-1,3,5-triazine and maleic anhydride. The EBT derivative was characterized by elemental analysis, acid value and spectral studies.

EBT was then polycondensed respectively with three commercial epoxy resins, namely diglycidyl ether of bisphenol-A (DGEBA), diglycidyl ether of bisphenol-F (DGEBF) and diglycidyl ether of bisphenol-C (DGEBC). The resultant polymers are designated as unsaturated polyester-s-triazine (UPETs) and were characterized by elemental analysis, spectral study, molecular weight determination, differential scanning calorimeter (DSC)and thermogravimetry. The interacting blends of UPETs with DGEBA epoxy resin was made at stoichiometric ratio. The blending of these systems was monitored on a differential scanning calorimeter (DSC), and based on DSC data the glass-reinforced composites (GRC_s) were prepared and characterized by physical and mechanical properties.     

Thermal stability of modified end‐capped poly(lactic acid)

The influence of functional end groups on the thermal stability of poly(lactic acid) (PLA) in nitrogen‐ and oxygen‐enriched atmospheres has been investigated in this article using differential scanning calorimetry, thermogravimetric analysis (TGA), and dynamic mechanical analysis (DMA). Functional end groups of PLA were modified by succinic anhydride and l ‐cysteine by the addition–elimination reaction. PLA was synthesized by azeotropic condensation of l ‐lactic acid in xylene and characterized by nuclear magnetic resonance. The values of the activation energies determined by TGA in nitrogen and oxygen atmospheres revealed that the character of functional end groups has remarkable influence on the thermal stability of PLA. Moreover, DMA confirmed the strong influence of functional end groups of PLA on polymer chains motion. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41105.     

The effect of formaldehyde/phenol (F/P) molar ratios on function and curing kinetics of high‐solid resol phenolic resins

A series of high‐solid resol phenolic resins (HSRPRs) were synthesized with different molar ratios (1.6, 1.8, 2.0, 2.2, and 2.4) of formaldehyde to phenol using calcium oxide and sodium hydroxide as catalyst. The effects of F/P molar ratios on physical properties, free formaldehyde and phenol, activity, structure, and thermally resistant properties of HSRPRs were fully investigated by chemical assays, liquid and solid ¹³C‐NMR, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The curing kinetics of different F/P molar ratios were explored with differential scanning calorimeter at four different heating rates (5, 10, 15, 20°C/min) from 35 to 200°C. Overall, HSRPRs with F/P = 2.0 had excellent comprehensive properties. The study was significant in solving the wastewater problem during the process of industry‐scale preparation of HSRPRs. We believed that the experimental findings would provide a new avenue for further study and application of HSRPRs. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis,Characterization and Glass/Carbon Reinforcement of Acetone-Formaldehyde-1,5-Dihydroxynaphthalene-Epoxy Resin System

Acetone-formaldehyde (AF) resin containing the methylol group (–CH₂OH) has been prepared and condensed with 1,5-dihydroxynaphthalene (DN) in the presence of an alcoholic alkali catalyst at varying ratios of AF:DN: 1:1, 1:1.5 and 1:2, respectively. The resultant AFDN resins were characterized by elemental analyses, IR spectral studies, and number average molecular weight determined by the nonaqueous conductometric titration method. Further reaction of the AFDN resins was carried out with different epoxy resins (i.e., DGEBA, DGEBC and DGEBF). The curing of these resins was monitored by differential scanning calorimeter (DSC) and their kinetic parameters have been evaluated. Based on DSC thermograms both glass and carbon fiber-reinforced composites have been laminated and characterized for chemical, mechanical and electrical properties. The unreinforced cured resins were subjected to thermogravimetric analysis (TGA).     

Processing and characterization of injection moldable polymer–particle composites applicable in brazing processes

A novel method has been developed to process highly filled polymer–particle composites to test samples as braze metal preforms. Polypropylene (PP), low‐density polyethylene (LD‐PE) and high‐density polyethylene (HD‐PE) were used as polymer matrices. Two types of nickel‐based braze metal microparticles (Ni 102 and EXP 152) were compounded to the polymer matrices at filler contents up to 65 vol %. With enhancing filler content, torque at kneading rotors, and injection molding parameter were significantly affected by increasing viscosity. Injection molded composites show well‐distributed spherical microparticles and particle–particle interactions. Polymers decompose residue‐free at temperatures above 550°C, even for their composites. Adding particles reduces polymer crystallinity, whereas defined cooling at 5°C/min significantly increases the crystallinity and melt peak temperature of polymers compared to undefined cooling prior injection molding. Storage modulus of polymers increases significantly by adding filler particles. LD‐PE + 65 vol % EXP 152 show the most suitable composite performance. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Thermal behavior of vinyl ester resin matrix composites reinforced with alkali‐treated jute fibers

The thermal behavior of vinyl ester resin matrix composites reinforced with jute fibers treated for 2, 4, 6, and 8 h with 5% NaOH was studied with Thermo‐gravimetric analysis and differential scanning calorimetry. The moisture desorption peak shifted to a higher temperature, from 37 to 58.3°C, for all the treated‐fiber composites because of improved wetting of the fibers by the resin and stronger bonding at the interface. The degradation temperature of the vinyl ester resin in the composites was lowered to 410.3°C from that of the neat resin, 418.8°C. The X‐ray diffraction studies showed increased crystallinity of the treated fibers, which affected the enthalpy of the α‐cellulose and hemicellulose degradation. The hemicellulose degradation temperature remained the same (299.7°C) in all the treated‐fiber composites, but the enthalpy associated with the hemicellulose degradation showed an increasing trend in the treated composites with a small increase in the weight loss. This could be attributed to the increased hydrogen bonding between the more accessible ? OH groups of the hemicellulose in the noncrystalline region of the jute fiber and the resin. The degradation temperature of α‐cellulose was lowered from 364.2 to 356.8°C in the treated composites. The enthalpy of α‐cellulose degradation showed a decreasing trend with a lowering of the weight loss. The crystalline regions of the fiber, consisting of closely packed α‐cellulose chains, were bonded with the resin mainly on the surface through hydrogen bonds and became more resistant to thermal degradation; this reduced the weight loss. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 123–129, 2004     

Recovery of heavy metals from aqueous solution by using radiation crosslinked poly(vinyl alcohol)

Crosslinked poly(vinyl alcohol) (PVA) and PVA/acrylic acid hydrogels, prepared by γ‐irradiation, were used in the removal of heavy metals from aqueous solution. Comparative studies of the properties of the two hydrogels were made. The application of the prepared hydrogels as adsorbent materials for Cu²⁺, Co²⁺, and Ni²⁺ from aqueous solution was studied. The chemical and physical properties of the hydrogels, before and after adsorption of the heavy metal ions, were investigated by means of thermogravimetric analysis, differential scanning calorimetry, and scanning electron microscopy. The efficiency of such hydrogels for the recovery of metal ions was determined by atomic absorption and UV spectroscopic analysis. The effect of changing pH on the metal uptake was also studied. It was found that the prepared hydrogels have a substantial ability to adsorb metal ions from their solution. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1649–1656, 2004     

Fabrication,characterization, and properties of poly(ethylene‐co‐vinyl acetate)/magnetite nanocomposites

Poly(ethylene‐co‐vinyl acetate) (EVA)/magnetite (Fe₃O₄) nanocomposite was prepared with different loading of Fe₃O₄ nanoparticles. The mixing and compounding were carried out on a two‐roll mixing mill and the sheets were prepared in a compression‐molding machine. The effect of loading of nanoparticles in EVA was investigated thoroughly by different characterization technique such as transmission electron microscopy (TEM), X‐ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), limiting oxygen index (LOI), and technological properties. TEM analysis showed the uniform dispersion of filler in the polymer matrix and the dispersion of filler decreased with increase in filler content. XRD of the nanocomposite revealed the more ordered structure of the polymer chain. An appreciable increase in glass transition temperature was observed owing to the restricted mobility of Fe₃O₄‐filled EVA nanocomposite. TGA and flame resistance studies indicated that the composites attain better thermal and flame resistance than EVA owing to the interaction of filler and polymer segments. Mechanical properties such as tensile strength, tear resistance, and modulus were increased for composites up to 7 phr of filler, which is presumably owing to aggregation of Fe₃O₄ nanoparticle at higher loading. The presence of Fe₃O₄ nanoparticles in the polymer matrix reduced the elongation at break and impact strength while improved hardness of the composite than unfilled EVA. The change in technological properties had been correlated with the variation of polymer–filler interaction estimated from the swelling behavior. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40116.     

Synthesis,Characterization and Glass Reinforcement of Poly(Ester Amido Imide)s

Poly(ester amido imide)s (PEAI)s (IIIa–e) were prepared by the intermolecular Diels-Alder (DA) reaction of bismaleimide (II) having epoxy resin segment with various bisfurans (Ia–e) having amide bridge. The DA reaction was carried out with tetrahydrofuran as a solvent, as well as in bulk, followed by aromatization of DA polyadduct intermediates in the presence of acetic anhydride. All the resultant polymers, designated as poly(ester amido imide)s (PEAI)s, were characterized by elemental analysis, number average molecular weight, IR spectral studies and thermogravimetry. The PEAIs exhibit good thermal stability. Bismaleimide (II) and bisfurans (Ia–e) were polymerized (at 150 ± 10°C) by in situ DA intermolecular reaction into moderately thermally stable PEAIs. The glass fiber-reinforced composites (i.e., laminates) of all PEAIs were prepared and characterized by their chemical resistance and mechanical properties.     

Thermal properties of extruded/injection‐molded poly(lactic acid) and biobased composites

To determine the degree of compatibility between poly(lactic acid) and different biomaterials (fibers), poly(lactic acid) was compounded with sugar beet pulp and apple fibers. The fibers were added in 85 : 15 and 70 : 30 poly(lactic acid)/fiber ratios. The composites were blended by extrusion followed by injection molding. Differential scanning calorimetry and thermogravimetric analysis were used to analyze the extruded and extruded/injection‐molded composites. After melting in sealed differential scanning calorimetry pans, the composites were cooled through immersion in liquid nitrogen and aged (stored) at room temperature for 0, 7, 15, and 30 days. After storage, the samples were heated from 25 to 180°C at 10°C/min. The neat poly(lactic acid) showed a glass‐transition transition at 59°C with a change in heat capacity (ΔC_p) value of 0.464. The glass transition was followed by crystallization and melting transitions. The enthalpic relaxation of the poly(lactic acid) and composites steadily increased as a function of the storage time. Although the presence of fibers had little effect on the enthalpic relaxation, injection molding reduced the enthalpic relaxation. The crystallinity percentage of the unprocessed neat poly(lactic acid) dropped by 95% after extrusion and by 80% for the extruded/injection‐molded composites. The degradation was performed in air and nitrogen environments. The degradation activation energy of neat poly(lactic acid) exhibited a significant drop in the nitrogen environment, although it increased in air. This meant that the poly(lactic acid) was more resistant to degradation in the presence of oxygen. Overall, injection molding appeared to reduce the activation energy for all the composites. Sugar beet pulp significantly reduced the activation energy in a nitrogen environment. In an air environment, both sugar beet pulp and apple fibers increased the activation energy. The enzymatic degradation of the composites showed a higher degradation rate for the extruded samples versus the extruded/injection‐molded composites, whereas the apple composites exhibited higher weight loss. The thermogravimetric analysis data showed that the degradation of unprocessed and extruded neat poly(lactic acid) followed a one‐step mechanism, whereas extruded/injection‐molded composites showed two‐step degradation. A higher fiber content resulted in up to three‐step degradation mechanisms. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Studies and characterization of RESOL/VAc–EHA/HMMM IPN systems in aqueous medium

Resol was solution‐blended with vinyl acetate‐2‐ethylhexyl acrylate (VAc–EHA) resin in an aqueous medium, in varying weight fractions, with hexamethoxymethylmelamine (HMMM) as a crosslinker and the data were compared with a control. The present work was aimed to obtain an optimum combination of high‐temperature resistance by synthesis of an interpenetrating network (IPN) of the resins. The control gave a semi‐IPN system, in which the resol crosslinked, while the acrylic did not, whereas the blend, where HMMM was the crosslinker, gave a full‐IPN system. FTIR spectra of the blends of resol/VAc–EHA/HMMM indicated the formation of new stretching, which was generated due to crosslinking reactions among VAc–EHA and the crosslinker HMMM. TGA showed that, with an increase in the VAc–EHA percent in semi‐IPNs, the decomposition temperature decreased gradually, whereas in case of full‐IPNs, the decomposition temperature increased with increase in the VAc–EHA percent. However, the full‐IPNs had a higher decomposition temperature than that of the semi‐IPNs, at the same resol/(VAc–EHA) ratio. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3581–3588, 2002     

Preparation of segmented semifluorinated poly(aryl ether)s from aromatic trifluorovinyl ethers and oligo(ethylene glycol)s

A series of new segmented semifluorinated polyaryl ethers (PAEs) containing a biphenyl segmented by semifluorinated oligoethylene (SFE) units were prepared by nucleophilic addition of a commercial oligo(ethylene glycol)s to 4,4′‐bis(4‐trifluorovinyloxy)biphenyl. These new thermoplastics were characterized by ¹H and F¹⁹ nuclear magnetic resonance (NMR) and attenuated total reflectance Fourier transform infrared (ATR‐FTIR). Gel permeation chromatography (GPC) analysis displayed number average molecular weights (M_ns) from 9000 to 13,000. Thermal properties of the polymers were studied by differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). DSC chromatograms displayed glass transition temperatures (T_gs) from 11 to 1°C. The onsets of degradations were observed by TGA analysis between 313 to 333°C in air and 326 to 363°C in nitrogen, respectively. A second onset of degradation was observed from 452 to 470°C for all polymers. In addition, crystalline morphologies were studied by tapping mode atomic force microscopy (TM‐AFM) and showed needle‐like crystallites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41798.     

Charge dynamics and thermal properties of epoxy based micro and nano hybrid composites at high temperatures

This paper presents the effects of the filler type and testing temperature on the charge dynamics and thermal properties of the epoxy resin. The micro-nano hybrid composites with different content of the micro and nano aluminum nitride (AlN) fillers are fabricated. The morphology of micro-nano hybrid composites is characterized. Electrical testing and thermal analysis methods are adopted to analyze its electrical and thermal performance. The results show that the space charge accumulation is suppressed and the charge decay process is facilitated in the hybrid composites. The electrical performances of the hybrid composites are enhanced by the nano-fillers. The apparent mobility and activation energy are decreased with nano-AlN fillers in the composites at the high temperature. The glass transition temperature and thermal stability of the materials is improved with the nano-AlN. A hypothetical mechanism is proposed to explain the charge carrier injection and transport of the composites at different temperatures.     

Thermomechanically stable dielectric composites based on poly(ether ketone) and BaTiO3 with improved electromagnetic shielding properties in X‐band

High‐performance barium titanate (BaTiO₃) filled poly(ether ketone) (PEK) composites were prepared by melt compounding with an aim to investigate the effect of BaTiO₃ on thermal, thermomechanical, dielectric, and electromagnetic interference shielding behavior of PEK. The content of BaTiO₃ in the PEK matrix was varied from 0 to 18 vol %. Scanning electron microscopy studies shows that BaTiO₃ particles were uniformly distributed in the PEK matrix up to 13 vol % loading followed by the formation of agglomerates at higher loading (18 vol %). Rockwell hardness increased up to 13 vol % loading followed by a decrease at 18 vol % loading. Dynamic mechanical analysis revealed that storage modulus increases with increase in BaTiO₃ loading with a maximum value of 3192 MPa at 13 vol % compared to 2099 MPa for neat PEK. Dielectric constant of composites measured in the frequency range of 8.2–12.4 GHz increased approximately three times upon incorporation of 18 vol % of BaTiO₃. This increment in dielectric constant is reflected in improved electromagnetic shielding properties as loading of dielectric filler (BaTiO₃) increases. Total shielding effectiveness of ?11 dB (～92% attenuation) at loading of 18 vol % BaTiO₃ justifies the use of these composites for suppression of EM radiations. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46413.