Effect of the addition of hydrophobic clay on the electrochemical property of polyacrylonitrile/LiClO4 polymer electrolytes for lithium battery

In this study, an organoclay, ALA-MMT, was prepared by the ionic exchange reaction of montmorillonite (MMT) with 12-aminododecanoic acid (ALA). ALA-MMT was then used as a filler to prepare a series of composite polymer electrolytes based on polyacrylonitrile (PAN) and LiClO₄. The effect of the addition of ALA-MMT on the properties of the composite polymer electrolytes (CPEs) was investigated by XRD, FT-IR, DSC, tensile strength, AC impedance, and cyclic voltammetry measurements. It was found that the ALA-MMT particles were well dispersed in the CPEs. Owing to the incorporation of ALA-MMT, a higher fraction of the free anions was obtained, indicating that the lithium salt dissolved in the PAN matrix more effectively for the CPE than in the PAN/LiClO₄ polymer electrolyte. Moreover, the glass-transition temperature was reduced, benefiting the ion transport. The best ionic conductivity at room temperature was obtained from the CPE with 7 wt% of the modified clay and 0.6 M LiClO₄ per PAN repeat unit (CPE-7) and was more than seven times higher than that from the corresponding PAN/LiClO₄ polymer electrolyte (CPE-0). The mechanical property and the cation transference number, t₊, of CPE-7 are largely increased compared to that of CPE-0. Besides, the CPEs were electrochemically stabilized up to 4.75 V and the corresponding cell exhibited excellent electrochemical stability and cyclability over the potential range between 0 V and 4.0 V vs. Li/Li⁺.     

Poly(methyl methacrylate) based nanocomposite gel polymer electrolytes with enhanced safety and performance

The study presents preparation of poly methyl methacrylate (PMMA) based nanocomposite gel polymer electrolytes consisting of, salt lithium perchlorate (LiClO₄), plasticizer PC/DEC and different proportions of SiO₂ nanofiber by solution casting process. The effect of the composition of the electrolytes on their ionic, mechanical and thermal characteristics was investigated. Morphology of the nanocomposite electrolyte films has been observed by scanning and transmission electron microscopes. Interactions among the constituents of the composite and structural changes of the base polymer were investigated by Fourier Transform Infrared (FTIR) spectroscopy and X-ray diffraction (XRD) techniques. The maximum conductivity i.e. 10^?3 Scm^?1 at room temperature is obtained with the electrolyte composition of 0.6(PMMA)-0.15(PC + DEC)-0.1LiClO₄ (wt%) containing 10 wt% SiO₂ nanofiber and the temperature dependent conductivity data of the electrolyte follows Vogel-Tamman-Fulcher (VTF) behavior.     

Polymer electrolytes based on poly(ethylene glycol) and cyanoresin

Polymer electrolytes based on a mixed polymer matrix consisting of poly(ethylene glycol) (PEG) and cyanoresins with lithium salt and plasticizer were prepared with an in situ blending process to improve both the mechanical properties and the ionic conductivity (σ). The PEG/lithium perchlorate (LiClO₄) complexes, including blends of cyanoethyl pullulan (CRS) and cyanoethyl poly(vinyl alcohol) (CRV), exhibited higher σ's than a simple PEG/LiClO₄ complex when the blend compositions of CRS/CRV were 5 : 5 or 3 : 7 or than CRV alone. When the CRS/CRV blend was compared with a copolymer of cyanoethyl pullulan and cyanoethyl poly(vinyl alcohol) (CRM) in the same molar ratio, the σ values of the polymer electrolytes containing the CRM copolymer series were slightly higher than those of the CRS/CRV blends containing PEG/LiClO₄ complexes. Moreover, the addition of cyanoresin to PEG/LiClO₄/(ethylene carbonate–propylene carbonate) polymer electrolytes provided better thermal stability and dynamic mechanical properties. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2402–2408, 2007     

Characterization of PEO-PAN hybrid solid polymer electrolytes

Hybrid solid polymer electrolytes (HSPE) of high ionic conductivity were prepared using polyethylene oxide (PEO), polyacrylonitrile (PAN), propylene carbonate (PrC), ethylene carbonate (EC), and LiClO₄. These electrolyte films were dry, free standing, and dimensionally stable. The HSPE films were characterized by constructing symmetrical cells containing nonblocking lithium electrodes as well as blocking stainless steel electrodes. Studies were made on ionic conductivity, electrochemical reaction, interfacial stability, and morphology of the films using alternating current impedance spectroscopy, infrared spectroscopy, and scanning electron microscopy. The properties of HSPE were compared with the films prepared using (i) PEO, PrC, and LiClO₄; and (ii) PAN, PrC, EC, and LiClO₄. The specific conductivity of the HSPE films was marginally less. Nevertheless, the dimensional stability was much superior. The interfacial stability of lithium was similar in the three electrolyte films. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 2191–2199, 1997     

Blending poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile) as composite polymer electrolyte

A blend of poly(methyl methacrylate) (PMMA) and poly(styrene‐co‐acrylonitrile) (PSAN) has been evaluated as a composite polymer electrolyte by means of differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy, ac impedance measurements, and linear sweep voltammetry (LSV). The blends show an interaction with the Li⁺ ions when complexed with lithium perchlorate (LiClO₄), which results in an increase in the glass‐transition temperature (T_g) of the blends. The purpose of using PSAN as another component of the blend is to improve the poor mechanical properties of PMMA‐based plasticized electrolytes. The mechanical property is further improved by introducing fumed silica as inert filler, and hence the liquid electrolyte uptake and ionic conductivity of the composite systems are increased. Room‐temperature conductivity of the order of 10^?4 S/cm has been achieved for one of the composite electrolytes made from a 1/1 blend of PSAN and PMMA containing 120% liquid electrolyte [1M LiClO₄/propylene carbonate (PC)] and 10% fumed silica. These systems also showed good compatibility with Li electrodes and sufficient electrochemical stability for safe operation in Li batteries. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1319–1328, 2001     

New solid polymer electrolytes based on PEO/PAN hybrids

Hybrid polymer dry electrolytes comprised of poly(ethylene oxide) (PEO), polyacrylonitrile (PAN), and LiClO₄ were investigated. The impedance spectroscopy showed that the effect of PAN on the ion conductivity of PEO‐based electrolytes depends on the concentration of lithium salt. When the mole ratio of lithium to oxygen is 0.062 (15%LiClO₄‐PEO), adding PAN will increase the ionic conductivity. Differential scanning calorimetry, NMR, and IR data suggested that the enhanced conductivity was due to both the decreasing of the PEO crystallinity and increasing of the degree of ionization of lithium salt. There was obviously no interaction between PAN and lithium ions, and PAN acts as a reinforcing filler, and hence contributes to the mechanical strength besides reducing the crystallinity of the polymer electrolytes. When the LiClO₄‐PEO‐PAN hybrid polymer electrolyte was heated at 200°C under N₂, PAN crosslinked partially, which further decreased the crystallinity of PEO and increased the ionic conductivity, and at the same time prevented the recrystallization of PEO upon sitting at ambient environment. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1530–1540, 2006     

Composite polymer electrolytes based on the low crosslinked copolymer of linear and hyperbranched polyurethanes

Low crosslinked copolymer of linear and hyperbranched polyurethane (CHPU) was prepared, and the ionic conductivities and thermal properties of the composite polymer electrolytes composed of CHPU and LiClO₄ were investigated. The FTIR and Raman spectra analysis indicated that the polyurethane copolymer could dissolve more lithium salt than the corresponding polymer electrolytes of the non crosslinked hyperbranched polyurethane, and showed higher conductivities. At salt concentration EO/Li = 4, the electrolyte CHPU30‐LiClO₄ reached its maximum conductivity, 1.51 × 10^?5 S cm^?1 at 25°C. DSC measurement was also used for the analysis of the thermal properties of polymer electrolytes. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3607–3613, 2007     

Review on composite polymer electrolytes for lithium batteries

This paper reviews the state of the art of composite polymer electrolytes (CPE) in view of their electrochemical and physical properties for the applications in lithium batteries. This review mainly encompasses on composite polymer electrolyte hosts namely poly(ethylene oxide) (PEO), poly(acrylonitrile) (PAN), poly(methyl methacrylate) (PMMA) and poly(vinylidene fluoride) (PVdF) studied so far. Also the ionic conductivity, transference number, compatibility and the cycling behavior of poly(vinylidene fluoride-hexafluoro propylene) (PVdF-HFP)-[AlO(OH)]_n-LiPF₆/LiClO₄ composite electrolytes have been studied and the results are discussed.     

1H NMR,thermal, and conductivity studies on PVAc based gel polymer electrolytes

The lithium‐ion conducting gel polymer electrolytes (GPE), PVAc‐DMF‐LiClO₄ of various compositions have been prepared by solution casting technique. ¹H NMR results reveal the existence of DMF in the gel polymer electrolytes at ambient temperature. Structure and surface morphology characterization have been studied by X‐ray diffraction analysis (XRD) and scanning electron microscopy (SEM) measurements. Thermal and conductivity behavior of polymer‐ and plasticizer‐salt complexes have been studied by differential scanning calorimetry (DSC), TG/DTA, and impedance spectroscopy results. XRD and SEM analyses indicate the amorphous nature of the gel polymer‐salt complex. DSC measurements show a decrease in T_g with the increase in DMF concentrations. The thermal stability of the PVAc : DMF : LiClO₄ gel polymer electrolytes has been found to be in the range of (30–60°C). The dc conductivity of gel polymer electrolytes, obtained from impedance spectra, has been found to vary between 7.6 × 10^?7 and 4.1 × 10^?4 S cm^?1 at 303 K depending on the concentration of DMF (10–20 wt %) in the polymer electrolytes. The temperature dependence of conductivity of the polymer electrolyte complexes appears to obey the VTF behavior. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and performance analysis of barium titanate incorporated in corn starch‐based polymer electrolytes for electric double layer capacitor application

Polymer electrolyte membranes composing of corn starch as host polymer, lithium perchlorate (LiClO₄) as salt, and barium titanate (BaTiO₃) as composite filler are prepared using solution casting technique. Ionic conductivity is enhanced on addition of BaTiO₃ by reducing the crystallinity and increasing the amorphous phase content of the polymer electrolyte. The highest ionic conductivity of 1.28 × 10^?2 S cm^?1 is obtained for 10 wt % BaTiO₃ filler in corn starch‐LiClO₄ polymer electrolytes at 75°C. Glass transition temperature (T_g) of polymer electrolytes decreases as the amount of BaTiO₃ filler is increased, as observed in differential scanning calorimetry analysis. Scanning electron microscopy and thermogravimetric analysis are employed to characterize surface morphological and thermal properties of BaTiO₃‐based composite polymer electrolytes. The electrochemical properties of the electric double‐layer capacitor fabricating using the highest ionic conductivity polymer electrolytes is investigated using cyclic voltammetry and charge‐discharge analysis. The discharge capacitance obtained is 16.22 F g^?1. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43275.     

Effect of modified montmorillonites on the ionic conductivity of (PEO)16LiClO4 electrolytes

Three kinds of modified montmorillonites were prepared by ion exchange method, and added into (PEO)₁₆LiClO₄ matrix to study the effect on the ionic conductivity of (PEO)₁₆LiClO₄ electrolytes. The structure of the modified montmorillonites and polymer composites were characterized by wide-angle X-ray diffraction. HP 4192A was used to measure the ionic conductivity of the polymer electrolytes. The results show that the addition of optimum content of 250-Li-mont enhances the ionic conductivity of the PEO based electrolyte by nearly 30 times more than the plain system and that is much higher than the other two modified montmorillonites. The difference of enhancement in conductivity caused by adding these three montmorillonites can be attributed to the difference in structure of the samples as characterized by wide-angle X-ray diffraction.     

Effect of PBMA on PVC‐based polymer blend electrolytes

Poly(vinyl chloride) (PVC)—poly(butyl methacrylate) (PBMA) blended polymer electrolytes with lithium perchlorate (LiClO₄) as the complexing salts are prepared by solution casting technique. The addition of PBMA into PVC matrix is found to induce considerable changes in physical and electrical properties of the polymer electrolytes. Addition of PBMA into PVC matrix is found to increase the conductivity by two orders of magnitude (1.108 × 10^?5 S cm^?1) when compared with that of the pristine PVC polymer electrolyte (10^?7 S cm^?1). Structural, thermal, mechanical, morphological, and polymer–salt interactions are ascertained from X‐ray diffraction (XRD), thermogravimetry/differential thermal analysis (TG/DTA), mechanical analysis, scanning electron microscope (SEM), and Fourier transform infrared spectroscopy (FTIR) respectively. A thermal stability upto 250 °C is asserted from the TG/DTA analysis. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44939.     

Effect of plasticizers in poly(vinyl alcohol)‐based hybrid solid polymer electrolytes

Hybrid solid polymer electrolyte films consisting of poly(vinyl alcohol) (PVA), poly(methyl methacrylate) (PMMA), LiBF₄, and ethylene carbonate/propylene carbonate (EC/PC) were prepared with a solvent‐casting technique. The complexation was investigated with Fourier transform infrared and X‐ray diffraction. The ionic conductivities of the electrolyte films were determined with an alternating‐current impedance technique for various temperatures in the range of 302–373 K. The maximum conductivity value, 1.2886 × 10^?3 S/cm, was observed for a PVA–PMMA–LiBF₄–EC complex. Thermogravimetry/differential thermal analysis was performed to ascertain the thermal stability of the electrolyte with the maximum conductivity value. For an examination of the cyclic and reversible performance of the film, a cyclic voltammetry study was carried out. The surface morphology of the EC‐and PC‐based electrolytes was examined with scanning electron microscopy. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2794–2800, 2003     

Development and investigation on PMMA–PVC blend-based solid polymer electrolytes with LiTFSI as dopant salt

PMMA–PVC polymer blend systems with LiTFSI as dopant salt were prepared by solution casting technique. Studies were then performed to explore the ionic conductivity, crystallographic structure, morphology, and thermal properties of these polymer electrolytes. XRD and SEM reveal amorphous behavior and morphologies of polymer electrolytes, respectively. Coherent length was calculated to determine the amorphousity of polymer complexes. Ionic conductivity was calculated using ac-impedance spectroscopy. DSC measurements revealed a decrease in T _g, whereas T _m and T _d were enhanced. The thermal properties of polymer electrolytes were found to enhance upon addition of 30 wt% LiTFSI. Increase in thermal stability of polymer electrolytes were further confirmed through TGA studies.     

Synthesis of polymer gel electrolyte with high molecular weight poly(methyl methacrylate)-clay nanocomposite

Polymer nanocomposite gel electrolytes consisting of high molecular weight poly(methyl methacrylate) PMMA-clay nanocomposite, ethylene carbonate (EC)/propylene carbonate (PC) as plasticizer, and LiClO₄ electrolyte are reported. Montmorillonite clay was ion exchanged with a zwitterionic surfactant (octadecyl dimethyl betaine) and dispersed in methyl methacrylate, which was then polymerized to synthesize PMMA-clay nanocomposites. The nanocomposite was dissolved in a mixture of EC/PC with LiClO₄, heated and pressed to obtain polymer gel electrolyte. X-ray diffraction (XRD) of the gels indicated intercalated clay structure with d-spacings of 2.85 and 1.40 nm. In the gel containing plasticizer, the clay galleries shrink suggesting intercalation rather than partial exfoliation observed in the PMMA-clay nanocomposite. Ionic conductivity varied slightly and exhibited a maximum value of 8 × 10⁻⁴ S/cm at clay content of 1.5 wt.%. The activation energy was determined by modeling the conductivity with a Vogel-Tamman-Fulcher expression. The clay layers are primarily trapped inside the polymer matrix. Consequently, the polymer does not interact significantly with LiClO₄ electrolyte as shown by FTIR. The presence of the clay increased the glass transition temperature (Tg) of the gel as determined by differential scanning calorimetry. The PMMA nanocomposite gel electrolyte shows a stable lithium interfacial resistance over time, which is a key factor for use in electrochemical applications.     

Enhanced Ionic Conductivity in Poly(ethylene oxide)/Layered Double Hydroxide Nanocomposite Electrolytes

All solid-state poly(ethylene oxide) (PEO) nanocomposite electrolytes were made containing nanoscale fillers of layered double hydroxides (LDHs). Two kinds of oligo(ethylene oxide) modified LDHs were prepared by template method, and added into PEO/LiClO₄ matrix (with EO/Li molar ratio of 8) to study the effect on the ionic conductivity of PEO/LDH nanocomposite electrolytes. The structures of the modified LDHs were characterized by infrared spectra, thermogravimetric analysis and wide-angle X-ray diffraction. The results show that the oligo(ethylene oxide) with phosphonate anion can be effectively intercalated into the gallery region of LDHs and formed as an organic-inorganic hybrid (PLDH). With enhanced compatibility of LDH sheets by oligo(ethylene oxide) surface modification, the PEO/PLDH nanocomposite exhibits fully exfoliation morphology. The well dispersed LDH layers in PEO/LiClO₄/PLDH nanocomposite electrolytes rendering the formation of amorphous phase, results in an enhancement of ionic conductivity by three orders of magnitude compared to the pure PEO/LiClO₄ polymer electrolyte. This novel nanocomposite electrolytes system with high ionic conductivity will be benefited to fabricate the thin-film type of Li-polymer secondary battery. This revised version was published online in July 2006 with corrections to the Cover Date.     

Solid polymer electrolytes. XI. Preparation,characterization and ionic conductivity of new plasticized polymer electrolytes based on chemical‐covalent polyether–siloxane hybrids

A new hybrid polymer electrolyte system based on chemical‐covalent polyether and siloxane phases is designed and prepared via the sol–gel approach and epoxide crosslinking. FT‐IR, ¹³C solid‐state NMR, and thermal analysis (differential scanning calorimetry (DSC) and TGA) are used to characterize the structure of these hybrids. These hybrid films are immersed into the liquid electrolyte (1M LiClO₄/propylene carbonate) to form plasticized polymer electrolytes. The effects of hybrid composition, liquid electrolyte content, and temperature on the ionic conductivity of hybrid electrolytes are investigated and discussed. DSC traces demonstrate the presence of two second‐order transitions for all the samples and show a significant change in the thermal events with the amount of absorbed LiClO₄/PC content. TGA results indicate these hybrid networks with excellent thermal stability. The EDS‐0.5 sample with a 75 wt % liquid electrolyte exhibits the ionic conductivity of 5.3 × 10^?3 S cm^?1 at 95°C and 1.4 × 10^?3 S cm^?1 at 15°C, in which the film shows homogenous and good mechanical strength as well as good chemical stability. In the plot of ionic conductivity and composition for these hybrids containing 45 wt % liquid electrolyte, the conductivity shows a maximum value corresponding to the sample with the weight ratio of GPTMS/PEGDE of 0.1. These obtained results are correlated and used to interpret the ion conduction behavior within the hybrid networks. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1000–1007, 2006     

Thermal, electrical and mechanical properties of plasticized polymer electrolytes based on PEO/P(VDF-HFP) blends

The polymer electrolytes composed of a blend of poly(ethylene oxide) (PEO) and poly(vinylidene fluoride-co-hexafluoropropylene) (P(VDF-HFP)) as a host polymer, mixture of ethylene carbonate (EC) and propylene carbonate (PC) as a plasticizer, and LiClO₄ as a salt were prepared by a solution casting technique. SEM micrographs show that P(VDF-HFP) is very compatible with PEO. The ionic conductivity of the electrolytes increases with increasing plasticizer content, while the mechanical properties become obviously worse. By addition of a certain content of PEO in P(VDF-HFP) matrix, a good compromise between high ionic conductivity and mechanical stability can be obtained.     

Calcium phosphate incorporated poly(ethylene oxide)‐based nanocomposite electrolytes for lithium batteries. I. Ionic conductivity and positron annihilation lifetime spectroscopy studies

Nanocomposite polymer electrolytes (NCPEs) composed of poly(ethylene oxide), calcium phosphate [Ca₃(PO₄)₂], and lithium perchlorate (LiClO₄)/lithium bis(trifluoromethane sulfonyl)imide [LiN(CF₃SO₂)₂ or LiTFSI] in various proportions were prepared by a hot‐press method. The membranes were characterized by scanning electron microscopy, differential scanning calorimetry, thermogravimetry–differential thermal analysis, ionic conductivity testing, and transference number studies. The free volume of the membranes was probed by positron annihilation lifetime spectroscopy at 30°C, and the results supported the ionic conductivity data. The NCPEs with LiClO₄ exhibited higher ionic conductivities than the NCPE with LiTFSI as a salt. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Morphological,infrared, and ionic conductivity studies of poly(ethylene oxide)–49% poly(methyl methacrylate) grafted natural rubber–lithium perchlorate salt based solid polymer electrolytes

The potential of poly(ethylene oxide) (PEO) and 49% poly(methyl methacrylate) grafted natural rubber (MG49) as a polymer host in solid polymer electrolytes (SPE) was explored for electrochemical applications. PEO–MG49 SPEs with various weight percentages of lithium perchlorate salt (LiClO₄) was prepared with the solution casting technique. Characterization by scanning electron microscopy, Fourier transform infrared spectroscopy, and impedance spectroscopy was done to investigate the effect of LiClO₄ on the morphological properties, chemical interaction, and ionic conductivity behavior of PEO–MG49. Scanning electron microscopy analysis showed that the surface morphology of the sample underwent a change from rough to smooth with the addition of lithium salts. Infrared analysis showed that the interaction occurred in the polymer host between the oxygen atom from the ether group (C? O? C) and the Li⁺ cation from doping salts. The ionic conductivity value increased with the addition of salts because of the increase in charge carrier up to the optimum value. The highest ionic conductivity obtained was 8.0 × 10^?6 S/cm at 15 wt % LiClO₄. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012