Use of C-factor for monitoring of fouling in a shell and tube heat exchanger

Heat exchangers operating in process industries are fouled during operations and results in decrease in the thermal efficiency of a heat exchanger. Once the thermal efficiency decreases to a minimum acceptable level, cleaning of the equipment becomes necessary to restore the performance. This paper uses C-factor as a tool for investigation of the performance of a heat exchanger due to fouling which consequently gives information regarding the extent of fouling developed on the heat transfer surfaces. The fouling parameters are predicted by measurements of flow rate and pressure drop. In contrast to most conventional methods, the extent of fouling can be detected considering the flow rate and pressure drop when the heat exchanger operates in transient states. The C-Factor is first calculated through out cleaning period and then compared with the clean and the design value. The results show that the proposed tool is very effective in detecting the fouling developed and the corresponding degradation in heat transfer efficiency of a heat exchanger. Hence the results of this work can find applications in predicting the reduction in heat transfer efficiency due to fouling in heat exchangers that are in operation and assist the exchanger operators to plan cleaning schedules.     

Performance analysis of finned tube and unbaffled shell-and-tube heat exchangers

This work considers an optimum design problem for the different constraints involved in the designing of a shell-and-tube heat exchanger consisting of longitudinally finned tubes. A Matlab simulation has been employed using the Kern's method of design of extended surface heat exchanger to determine the behavior on varying the values of the constraints and studying the overall behavior of the heat exchanger with their variation for both cases of triangular and square pitch arrangements, along with the values of pressure drop. It was found out that an optimum fin height existed for particular values of shell and tube diameters when the heat transfer rate was the maximum. Moreover it was found out that the optimum fin height increased linearly with the increase in tube outer diameter. Further studies were also performed with the variation of other important heat exchanger design features and their effects were studied on the behavior of overall performance of the shell-and-tube heat exchanger. The results were thereby summarized which would proclaim to the best performance of the heat exchanger and therefore capable of giving a good idea to the designer about the dimensional characteristics to be used for designing of a particular shell and tube heat exchanger.     

Thermal performance and pressure drop of the helical-coil heat exchangers with and without helically crimped fins

In the present study, the thermal performance and pressure drop of the helical-coil heat exchanger with and without helical crimped fins are studied. The heat exchanger consists of a shell and helically coiled tube unit with two different coil diameters. Each coil is fabricated by bending a 9.50 mm diameter straight copper tube into a helical-coil tube of thirteen turns. Cold and hot water are used as working fluids in shell side and tube side, respectively. The experiments are done at the cold and hot water mass flow rates ranging between 0.10 and 0.22 kg/s, and between 0.02 and 0.12 kg/s, respectively. The inlet temperatures of cold and hot water are between 15 and 25 °C, and between 35 and 45 °C, respectively. The cold water entering the heat exchanger at the outer channel flows across the helical tube and flows out at the inner channel. The hot water enters the heat exchanger at the inner helical-coil tube and flows along the helical tube. The effects of the inlet conditions of both working fluids flowing through the test section on the heat transfer characteristics are discussed.     

Thermal and hydraulic characteristics of nanofluid flow in a helically coiled tube heat exchanger

The effects of using different geometrical parameters with the combination of nanofluid on heat transfer and fluid flow characteristics in a helically coiled tube heat exchanger (HCTHE) are numerically investigated. A CuO nanoparticle with a diameter of 25 nm dispersed in water with a particle concentration of 4% was used as the working fluid. The three dimensional governing equations (continuity, momentum and energy) along with the boundary conditions are solved using the finite volume method (FVM). The mass flow rate of water in the annulus was kept constant and the nanofluid flow rate in the inner tube was varied. The effect of flow configuration (parallel and counter) was also examined in this study. The performance of the HCTHE was evaluated in terms of Nusselt number, heat transfer rate, pressure drop, effectiveness and performance index. The results reveal that certain geometrical parameters such as the helix radius and inner tube diameter do affect the performance of the HCTHE under laminar flow conditions. It is also found that counter-flow configuration produced better results as compared to parallel-flow configuration.     

Thermal performance enhancement of melting and solidification process of phase‐change material in triplex tube heat exchanger using longitudinal fins

Efficient application of intermittent renewable energy sources, like solar, waste heat recovery, and so forth, depends on a large extent on the thermal energy storage methods. Latent heat energy storage with the use of phase‐change material (PCM) is the most promising one because it stores large energy in the form of latent heat at a constant temperature. The current study investigates melting and solidification of PCM in the triplex tube heat exchanger (TTHX) numerically. The two‐dimensional numerical model has been developed using Ansys Fluent 16.2, which considers the effects of conduction as well as natural convection. To overcome the limitation imposed by the poor thermal conductivity of PCM, use of fins is the better solution. In the current study, longitudinal fins are used for better performance of TTHX, which increases heat‐transfer area between PCM and heat‐transfer fluid. The effects of location of fins, that is, internal, external, and combined internal‐external fins, are observed. All three configurations improve melting as well as solidification process. During the melting process, internal and combined internal‐external fins are equally efficient, in which maximum 59% to 60% reduction in melting time is achieved. For solidification, internal‐external fins combination gives maximum 58% reduction in solidification time.     

Turbulent heat transfer enhancement in a heat exchanger using helically corrugated tube

The augmentation of convective heat transfer in a single-phase turbulent flow by using helically corrugated tubes has been experimentally investigated. Effects of pitch-to-diameter ratio (P/D_H = 0.18, 0.22 and 0.27) and rib-height to diameter ratio (e/D_H = 0.02, 0.04 and 0.06) of helically corrugated tubes on the heat transfer enhancement, isothermal friction and thermal performance factor in a concentric tube heat exchanger are examined. The experiments were conducted over a wide range of turbulent fluid flow of Reynolds number from 5500 to 60,000 by employing water as the test fluid. Experimental results show that the heat transfer and thermal performance of the corrugated tube are considerably increased compared to those of the smooth tube. The mean increase in heat transfer rate is between 123% and 232% at the test range, depending on the rib height/pitch ratios and Reynolds number while the maximum thermal performance is found to be about 2.3 for using the corrugated tube with P/D_H = 0.27 and e/D_H = 0.06 at low Reynolds number. Also, the pressure loss result reveals that the average friction factor of the corrugated tube is in a range between 1.46 and 1.93 times over the smooth tube. In addition, correlations of the Nusselt number, friction factor and thermal performance factor in terms of pitch ratio (P/D_H), rib-height ratio (e/D_H), Reynolds number (Re), and Prandtl number (Pr) for the corrugated tube are determined, based on the curve fitting of the experimental data.     

Thermal-hydraulic performance of novel louvered fin using flat tube cross-flow heat exchanger

Experimental studies were conducted to investigate the air-side heat transfer and pressure drop characteristics of a novel louvered fins and flat tube heat exchangers. A series of tests were conducted for 9 heat exchangers with different fin space and fin length, at a constant tube-side water flow rate of 2.8 m³/h. The air side thermal performance data were analyzed using the effectiveness-NTU method. Results were presented as plot of Colburn j factor and friction factor f against the Reynolds number in the range of 500–6500. The characteristics of the heat transfer and pressure drop of different fin space and fin length were analyzed and compared. In addition, the curves of the heat transfer coefficients vs. pumping power per unit heat transfer area were plotted. Finally, the area optimization factor was used to evaluate the thermal hydraulic performance of the louvered fins with differential geometries. The results showed that the j and f factors increase with the decrease of the fin space and fin length, and the fin space has more obvious effect on the thermal hydraulic characteristics of the novel louvered fins. __________ Translated from Journal of Shanghai Jiaotong University, 2007, 41(3): 380–383 [译自: 上海交通大学学报]     

Experimental study on the heat transfer enhancement of MWNT-water nanofluid in a shell and tube heat exchanger

Heat transfer enhancement of multi-walled carbon natube(MWNT)/water nanofluid in a horizontal shell and tube heat exchanger has been studied experimentally. Carbon nanotubes were synthesized by the use of catalytic chemical vapor deposition (CCVD) method over Co–Mo/MgO nanocatalyst. Obtained MWNTs were purified using a three stage method. COOH functional groups were inserted for making the nanotubes hydrophilic and increasing the stability of the nanofluid. The results indicate that heat transfer enhances in the presence of multi-walled nanotubes in comparison with the base fluid.     

Enhancement of heat transfer in a tube with regularly-spaced helical tape swirl generators

Influence of helical tapes inserted in a tube on heat transfer enhancement is studied experimentally. A helical tape is inserted in the tube with a view to generating swirl flow that helps to increase the heat transfer rate of the tube. The flow rate of the tube is considered in a range of Reynolds number between 2300 and 8800. The swirling flow devices consisting of: (1) the full-length helical tape with or without a centered-rod, and (2) the regularly-spaced helical tape, are inserted in the inner tube of a concentric tube heat exchanger. Hot air is passed through the inner tube whereas cold water is flowed in the annulus. The experimental data obtained are compared with those obtained from plain tubes of published data. Experimental results confirmed that the use of helical tapes leads to a higher heat transfer rate over the plain tube. The full-length helical tape with rod provides the highest heat transfer rate about 10% better than that without rod but it increased the pressure drop. To overcome this, different free-spacing ratio (s = L_s/L_h) of 0.5, 1.0, 1.5, and 2.0 were examined. It was found that the space ratio value should be about unity for Re < 4000. The regularly-spaced helical tape inserts at s = 0.5 yields the highest Nusselt number which is about 50% above the plain tube.     

Concentration solar dryer water-to-air heat exchanger: Modeling and parametric studies

In this paper we present a modeling and parametric studies of a water-to-air heat exchanger. This exchanger is formed of a fan blowing the air to be heated through a battery of smooth tubes where the hot water—coming from solar concentrators—circulates. The heated air is injected into a thermal room to dry the clay bricks.In the first part, we study the most used models in the estimation of the heat transfer and air flow pressure drop across a tube bundle, and subsequently calculate the required transmitted power to the air.In the second part, we focus on the parametric study of the influence of the different geometric parameters of the exchanger on the heat flow rate, the air outlet temperature, the pressure drop and the requested transferred power to the air. The considered parameters are: The water heat flow rate, the heat exchanger compactness, the rows arrangement, the tube diameter, the transverse pitch, the total number of tubes, the number of rows and the air velocity.Simulations have shown that the heat exchanger performance could be improved essentially throughout the design and manufacturing process by modifying the different geometrical parameters and filling certain conditions.     

Experimental investigation of heat transfer in a triple tube heat exchanger with coiled spring inserts

Experiments have been performed to investigate the effect of coiled spring inserts on heat transfer, pressure drop, and performance parameters of a triple tube heat exchanger (TTHX). Three different spring inserts having a pitch of 5, 10, and 15 mm are used and the diameter of the spring wire is taken as 1 mm. The experiments were carried out under a turbulent flow regime, with water as a working medium in parallel and counter flow configurations. The variation in different performance characteristics like heat transfer coefficient, Nusselt number, and effectiveness have been compared at various Reynolds numbers ranging between 4000 and 16,000 in the considered flow patterns. The Nusselt number of TTHX with the lowest pitch spring is found to be higher than that of the plain TTHX by 57.27% at Re = 4000 for the counter flow configuration. Both the thermal performance factor and effectiveness increased as the pitch of the spring insert was decreased. The effectiveness of TTHX with the lowest pitch spring insert is found higher than that of the plain TTHX by 43.84% in the counter flow pattern.     

Use of segmental baffle in shell and tube heat exchanger for nano emulsions

Among the heat exchangers (HE), the shell and tube type is being widely used in different applications like oil, chemical, and power plant Industries. The incorporation of segmental baffles (SB) improves the HE capacity from higher temperature fluid to lower temperature fluid. Nanofluids can be effectively used to enhance the heat transfer rate. In this study, numerical simulations have been carried out in a shell and tube heat exchanger (STHX). Among HE design methods, Tubular Exchanger Manufacturers Association (TEMA) standard is being used for better design by many researchers. In this paper, the computational fluid dynamics analysis was carried out with Al₂O₃, CuO, and SiO₂ nanofluids amid 1, 3, and 5 vol. % with water emulsion to enhance the heat transfer coefficient of STHX. The nanofluid has been used in the cold fluid of the HE and on the other side hot water is used. From the results, it is noticed that with the increase of Nanofluids, the value of heat transfer coefficients is found to be increasing. The overall heat transfer coefficient has been enhanced for Al₂O₃, CuO, and SiO₂ about 10.41%, 12.27%, and 9.56%, respectively, at 0.22 kg/s for the 5 vol. % addition. It is also depicted that the pressure drop is increasing with the incorporation of nanofluids.     

Thermal performance of a single-row fin-and-tube heat exchanger

Experiments were carried out to study the heat transfer characteristics of a single-row aluminum fin-and-tube crossflow heat exchanger with an emphasis in the regime of low flow rate of the in-tube fluid. The Chilton-Colburn analogy, in conjunction with the least-squares power-law technique, was used to correlate experimental data. Both air- and water-side heat transfer correlations were developed in the form of the Nusselt numbers as a function of Reynolds and Prandtl numbers. The experimental observations are quantitatively compared to the predictions of correlations available in the published literature. Different transfer mechanisms were found to be operative in the ranges of water-side Reynolds numbers based on the hydraulic diameter. In a range of Reynolds number from 1,200 to 6,000, the water-side thermal resistance accounts for less than ten percent of the overall thermal resistance. The dominant thermal resistance is always on the air-side. On the other hand, the thermal resistance of water-side is nearly equal to that of air-side in a Reynolds number range from 500 to 1,200.     

Design and investigation of hydriding alloy based hydrogen storage reactor integrated with a pin fin tube heat exchanger

The reaction between metal hydride (MH) and hydrogen gas generates substantial amount of heat. It must be removed rapidly to sustain the reaction in the metal hydride hydrogen storage reactor. Previous studies indicate that the performance of the reactor can be improved by inserting an efficient heat exchanger design inside the metal hydride bed. In the present study, a cylindrical shaped metal hydride system containing LaNi₅, integrated with a finned tube heat exchanger assembly made of copper pin fins and tubes, is presented. A 3-D numerical model is formulated in COMSOL Multiphysics 4.4 to study the transient behavior of sorption process inside the reactor. Experimental data obtained from the literature is used to approve the legitimacy of the proposed model. Influence of various operating and geometric parameters on the total absorption time of the reactor has been investigated. It is found that hydrogen supply pressure is the most influencing factor to increase the absorption rate of hydrogen. Total absorption time of the reactor is found to be 636 s with maximum storage capacity of 1.4 wt% at the operating conditions of 15 bar H₂ gas supply pressure, heat transfer fluid temperature of 298 K and flow rate of 6.75 l/min.     

Numerical investigation on the single phase forced convection heat transfer characteristics of TiO2 nanofluids in a double-tube counter flow heat exchanger

In this study, forced convection flows of nanofluids consisting of water with TiO₂ and Al₂O₃ nanoparticles in a horizontal tube with constant wall temperature are investigated numerically. The horizontal test section is modeled and solved using a CFD program. Palm et al.'s correlations are used to determine the nanofluid properties. A single-phase model having two-dimensional equations is employed with either constant or temperature dependent properties to study the hydrodynamics and thermal behaviors of the nanofluid flow. The numerical investigation is performed for a constant particle size of Al₂O₃ as a case study after the validation of its model by means of the experimental data of Duangthongsuk and Wongwises with TiO₂ nanoparticles. The velocity and temperature vectors are presented in the entrance and fully developed region. The variations of the fluid temperature, local heat transfer coefficient and pressure drop along tube length are shown in the paper. Effects of nanoparticles concentration and Reynolds number on the wall shear stress, Nusselt number, heat transfer coefficient and pressure drop are presented. Numerical results show the heat transfer enhancement due to presence of the nanoparticles in the fluid in accordance with the results of the experimental study used for the validation process of the numerical model.     

空气横掠矩形翅片椭圆管束换热规律的数值研究

采用Fluent软件对矩形翅片椭圆管束空气侧的对流换热情况进行了三维数值模拟,获得了不同流速下翅片表面温度分布,分析了迎面风速与换热系数之间的关系,随着速度的增大,空气侧的换热系数增加,并拟合了换热计算公式。同时分析了不同翅片间距对换热的影响因素,随着翅片间距的增大,空气侧换热系数增加,而且随着Rg数的增加,换热的强化更加明显。     

Pressure drop optimisation in debottlenecking of heat exchanger networks

Process integration technology is now widely applied in grass-roots design, energy saving retrofit and the debottlenecking of heat exchanger networks. This technology has been used in a variety of industries and proved to be reliable and applicable in engineering design. Debottlenecking may apply to a specific part or entire unit, whether it is due to increased throughput or process modifications. One of the advanced methods for debottlenecking that is currently used is based upon fixed allowable pressure drops, through which a retrofit can be achieved without a need for pump and/or compressor replacement. This research is trying to develop a new procedure for pressure drop optimisation in debottlenecking. This procedure enables the designer to study pump and/or compressor replacement whilst at the same time optimising the additional area and operating cost of the network. It deals with the problem of optimal debottlenecking of heat exchanger networks considering minimum total cost. Moreover, one can consider the possibility of the replacement of a given pump with a smaller one. The new procedure has been effectively applied to a crude oil pre-heat train, which was subject to some 20% increase in throughput, and the corresponding results proved to be accurate enough.     

Experiments on solid state hydrogen storage device with a finned tube heat exchanger

The absorption and desorption performances of a solid state (metal hydride) hydrogen storage device with a finned tube heat exchanger are experimentally investigated. The heat exchanger design consists of two “U” shaped cooling tubes and perforated annular copper fins. Copper flakes are also inserted in between the fins to increase the overall effective thermal conductivity of the metal hydride bed. Experiments are performed on the storage device containing 1 kg of hydriding alloy LaNi₅, at various hydrogen supply pressures. Water is used as the heat transfer fluid. The performance of the storage device is investigated for different operating parameters such as hydrogen supply pressure, cooling fluid temperature and heating fluid temperature. The shortest charging time found is 490 s for the absorption capacity of 1.2 wt% at a supply pressure of 15 bar and cooling fluid temperature and velocity of 288 K and 1 m/s respectively. The effect of copper flakes on absorption performance is also investigated and compared with a similar storage device without copper flakes.     

Performance evaluation of flattened tube in boiling heat transfer enhancement and its effect on pressure drop

An experimental investigation has been carried out to study heat transfer and pressure drop characteristics of R-134a flow boiling inside a horizontal plain tube and different flattened tubes. Round copper tubes with an inner diameter of 8.7 mm were flattened into an oblong shape with an internal height of 6.6 mm, 5.5 mm, 3.8 mm, and 2.8 mm. The test apparatus was basically a vapor compression refrigeration system equipped with all necessary measuring instruments. Analysis of the collected data showed that, by flattening the round tube, the heat transfer coefficient and pressure drop increased simultaneously. The performance of these tubes from the point of view of heat transfer enhancement and pressure drop increasing were evaluated. It was concluded that, the tube with an internal height of 5.5 mm has the best performance compared with the other flattened tubes. Finally, based on the present experimental pressure drop data, a correlation was developed to estimate the pressure drop in flattened tubes. This correlation predicts the experimental data of the present study within an error band of ± 20%.     

Twisted bundle heat exchangers performance evaluation by CFD (CJ12/5054)

Shell and tube heat exchanger with single twisted tube bundle in five different twist angles, are studied using computational fluid dynamics (CFD) and compared to the conventional shell and tube heat exchanger with single segmental baffles. Effect of shell-side nozzles configurations on heat exchanger performance is studied as well. Heat transfer rate and pressure drop are the main issues investigated in the paper. The results show that, for the same shell-side flow rate, the heat transfer coefficient of heat exchanger with twisted tube bundle is lower than that of the heat exchanger with segmental baffles while shell-side pressure drop of the former is even much lower than that of the latter. The comparison of heat transfer rate per unit pressure drop versus shell-side mass flow rate shows that heat exchanger with twisted tube bundle in both cases of perpendicular and tangential shell-side nozzles, has significant performance advantages over the segmental baffled heat exchanger. Optimum bundle twist angles for such exchangers are found to be 65 and 55° for all shell side flow rates.