Comparison of Drying Kinetics of Paddy Using a Pneumatic Conveying Dryer with and without a Cyclone

The objective of the present work is to find the possibility of reducing the high initial moisture content of wet paddy using a small-scale, low-cost pneumatic conveying dryer that can be provided for each farming household. The dryer without a cyclone equipped at the exit of the dryer is studied and the data obtained from this system is compared with those obtained previously from the dryer with a cyclone. Parametric effects of the following variables are examined: velocity of drying air from 20 to 30 m/s, feed rate of rough rice from 150 to 350 kg/h, and drying air temperature from 35 to 70°C. From the experimental results it is found that the drying process with and without a cyclone are able to lead to very rapid drying without any grain quality problems such as cracks in the rice kernel. For the same experimental conditions, the cyclone-equipped dryer gives around 1% higher decrease of moisture content, 2°C higher average surface temperature of paddy, 3–4% higher average percentage of head rice yield, and 2 kg/h higher average evaporation rate. However, the energy consumption per evaporated mass of water is 20–30% lower than the non-cyclone-equipped dryer.     

A Small-Scale Pneumatic Conveying Dryer of Rough Rice

This article studies the possibility of reducing the high initial moisture content of wet rough rice using a small-scale low-cost pneumatic conveying dryer as a first stage dryer. The parameters investigated are final moisture content, surface temperature of rough rice, head rice yield, drying rate, power consumption per unit mass of evaporated water, and physical characteristics of rice. Parametric effects of the following variables are examined: velocity of drying air from 20 to 30 m/s, feed rate of rough rice from 150 to 350 kg/h, initial moisture content from 22 to 26% (wet basis), and drying air temperature from 35 to 70°C. From the experimental results, it is found that this drying method can be used for fresh rough rice with an initial moisture content of over 24% (wet basis). The drying process is able to lead to very rapid drying without any grain quality problems such as cracks in the rice kernel. The moisture content can be reduced to approximately 18% (wet basis) or about 5-6% of the initial moisture content within 3-4 s. The optimal drying air temperature is in the range of 50 to 60°C. A comparison of pneumatic conveying drying data obtained from the present study with fluidized bed drying data reported in the open literature is also discussed.     

A Superheated-Steam Fluidized-Bed Dryer for Parboiled Rice: Testing of a Pilot-Scale and Mathematical Model Development

This article describes the testing of a pilot-scale superheated-steam fluidized-bed dryer for parboiled rice along with development of a mathematical model for predicting the changes in temperature of steam and moisture content of parboiled rice during drying. Based on the obtained results, it was found that the superficial velocity of steam from 1.3 to 1.5 times of the minimum fluidization velocity had no significant effect on the drying rates of rice. The energy consumption for reducing the moisture content of paddy from 0.43 to 0.22 kg/kg dry basis was approximately 7.2 MJ/kg water evaporated. Drying temperature caused the appreciable change of parboiled rice qualities as characterized by water adsorption, whiteness and pasting viscosities, white belly, and hardness. Soaking paddy at a temperature of 70°C for 7-8 h before drying was sufficiently enough for producing parboiled rice, with no white belly. The gelatinization of starch during drying resulted in higher head rice yield of the product as compared to that of raw paddy.     

MOBILE FLUIDIZED BED PADDY DRYER

The objectives of this research are to design, construct and test a mobile fluidized bed paddy dryer with a drying capacity of 2.5-4.0 t/h. Suitable drying conditions are recommended as follows : drying capacity 3.8 t/h, bed velocity 2.8 m/s, average drying air temperature 144 °C, bed height 13.5 cm, fraction of air recycled 0.8. Residence time of paddy was approximately 1.3 minutes. Test results showed that moisture content of paddy was reduced from 32.6 % dry-basis to 25.8 % dry-basis. Consumption of electrical power and diesel fuel was 12.9 kW and 21.71 1/h respectively. Primary energy consumption was 910.9 MJ/h. The dryer could evaporate water 218.8 kg/h. Specific primary energy consumption was 4.2 MJ/kg-water evaporated. Cost of paddy drying was 1.48 baht/kg-water evaporated of which 0.53 was fixed cost and 0.95 was energy cost (US$1 =34baht).     

Experiments on In-Store Paddy Drying Under Tropical Climate: Simulation and Product Quality

The main objective of this work is to study the rice whiteness and paddy qualities of rice in terms of hardness, stickiness, cohesiveness, and germination of rice. The prediction results of moisture content and whiteness are compared with the experimental results using a near-equilibrium drying model, which is modified by including whiteness kinetics of rice kernel. The long grain rice (Suphanburi 1 high amylose indica variety), which consists of 27% amylose was used for all experiments. The experiments were carried out at the average ambient temperature range of 28.6-30.8°C, average relative humidity of 65.2-80.6% with a fixed bed depth of 1.0 m. Specific air flow rates of 0.65 and 0.93 m³/min-m³ of paddy were forced continuously through the paddy bulk at initial moisture contents of 18.5% and 20.1% wet basis, respectively. The desired final moisture content of paddy is about 13.3 ± 0.6% wet basis. The results show that drying rate and the whiteness predictions are in good agreement with those from the experiments. The in-store drying using ambient air condition did not produce notable effect on the rice whiteness, head rice yield, and the percentage of paddy germination. However, the hardness, stickiness, and cohesiveness of rice were changed.     

PERFORMANCE STUDY OF A RE-CIRCULATING CABINET DRYER USING A HOUSEHOLD DEHUMIDIFIER

The performance and operating characteristics of a low temperature re-circulating cabinet dryer using a dehumidifier loop were studied using alfalfa. Chopped alfalfa, initially at 70% moisture content, was dried to 10% moisture content in the dryer. Two dryer setups were used. The dryers in each case had a partitioned cabinet with trays of material on one side and a stack of one or two small household dehumidifiers on the other side. Air was re-circulated through the material from bottom to the top and back through the dehumidifiers. Two drying configurations were tested. In one, the material was left on the trays until drying was complete (batch or fixed tray drying). In the other configuration, the trays were moved from top to bottom, introducing a new tray at the top while removing an old tray from bottom. Drying air temperature ranged from 25 to 45°C. The average air velocity through the material was 0.38 m/s. Alfalfa chops dried in 5 h in the fixed tray drying and in 4 h in the moving tray drying. The specific moisture extraction rate ranged from 0.35 to 1.02 kg/kWh for batch drying and stayed at an average value of 0.50 kg/kWh for continuous/moving tray drying.     

Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

DRYING OF CARROTS IN A FLUIDIZED BED. I. EFFECTS OF DRYING CONDITIONS AND MODELLING

Drying curves were determined in a mechanically agitated fluidized bed dryer, at temperatures between 70°C and 160°C, air velocities between 1.1 m/s and 2.2 m/s and stirring rates between 30 rpm and 70 rpm for batch drying of 3 kg lots of carrot slices, measuring the moisture content and shrinking of the particles in time. This was complemented by a study of the rate and degree of swelling of dried carrot particles in water between 20 and 75°C. Drying kinetics were modeled by Fick's second law, for which an optimal agreement with the experimental data was obtained when the effective diffusivity (D_e) was determined by a correlation based on the air velocity (v), the air temperature (T) and the dimensional moisture content of the carrot particles (X/X_o). Loss of carotenes is minimized when dehydration is carried out at about 130°C with a drying time below 12 min.     

A Novel Design of Crop Dryer for Use in Developing Countries

The dryer is required for drying of grain as well as drying of the processed products in small catchment agro processing centers in the developing world. However, due to varied material characteristics of grain and secondary processed product, two entirely different types of dryers are required. The grain is dried in a recirculatory dryer, whereas processed product is dried in a tray dryer, where it is frequently mixed and trays are also intermittently changed. To avoid the need for two dryers, a novel design of a low-cost hot air dryer was developed where just by changing the trays the dryer can be converted from an LSU grain dryer to a tray-type product dryer. The dryer was tested for drying soybean grain as well as processed soy products like blanched soybean dal and soyflakes. The capacity of the dryer was 100 kg/batch in a tray dryer with each tray accommodating 10 kg of wet material. In case of LSU mode, the capacity of the dryer was 250 kg of grain per batch. The drying time required was 5 h for 250 kg of wet soybean from 24 to 10% moisture content, whereas in a tray dryer 100 kg blanched soybean dal was dried from 60 to 10% in 5 h and 100 kg of soyflakes from 25% moisture content to 10% moisture in 1.75 h. The cost of the dryer is estimated at US$580.00 and it can be fabricated in a moderately equipped workshop in developing countries.     

Drying Characteristics of Malaysian Paddy: Kinetics & Grain Cracking Quality

Drying kinetics of Malaysian paddy dried in a laboratory scale batch rapid bin dryer was studied. Quality of paddy after drying at temperatures of 60 and 80°C, bed heights of 2 and 4 cm, and at different drying stages was presented in terms of cracking percentage. Moisture content of paddy reduced exponentially with time and became stable at equilibrium moisture content. Characteristic drying rate curves exhibited mainly falling rate period, with an induction period in deep beds, but without the constant rate period. A custom-made light box was built to visually analyze the cracking in paddy kernel. The extent of breakage is directly related to the crack percentage. The percentage of cracks increased with drying and tempering temperatures and was higher after 2 weeks of storage before milling. Bed heights did not significantly affect the head rice yield as much as tempering between two drying stages. Temperatures above 80°C caused severe cracking in paddy kernel and produced miserable yield of head rice after milling, which could be slightly improved by tempering. The use of a proper miller is also important in ensuring good head yield results and whiteness quality.     

A Study of the Limitations to Spray Dryer Outlet Performance

The concept of the product moisture locus was tested in this work using a pilot-scale modified Niro spray dryer (diameter 0.8 m, height 2 m), where the residence time of the particles inside this spray dryer is lower compared with larger industrial spray dryers. The moisture contents of skim milk powder produced from spray drying skim milk (solids content 8.8% w/v) at different operating conditions, namely different swirl vane angles (0°, 25°, 30°), inlet air temperatures (170°C, 200°C, 230°C) and process fluid flowrates (1.4 kg h^-1, 1.6 kg h^-1, 1.8 kg h^-1), were compared with the predicted equilibrium moisture contents. In addition, the residence time of the particles was also increased in the spray dryer by decreasing the inlet air mass flowrate from 0.016 to 0.013 kg s^-1. The outlet moisture contents of the skim milk powder for all the 23 runs carried out in this work were within 0.4% of the equilibrium values. Thus, the skim milk powder particles were in close equilibrium with the gas inside the drying chamber. These equilibrium limitations are confirmed by other literature data (Boonyai, P. Comparative Evaluation of Soymilk Drying in a Spray Dryer and Spouted Bed of Inert Particles. M.Sc. Thesis. Asian Institute of Technology: Bangkok, Thailand, 2000; 90 pp; Harvie, D.J.E.; Langrish, T.A.G.; Fletcher, D.F. A computational fluid dynamics study of a tall-form spray dryer. Trans IChemE 2002, in press). The use of this finding to predict spray dryer performance is demonstrated by mass and energy balance calculations.     

MANAGING MOIST PADDY BY DRYING, TEMPERING AND AMBIENT AIR VENTILATION

This paper describes a strategy for reducing moisture in paddy by fluidized bed drying, tempering and ambient air cooling. Experimental results showed that after the three processes, moisture content was reduced from 33 % to 16.5 % dry-basis within approximately 53 minutes. During the first process, a fluidized-bed dryer was used to reduce the moisture content of paddy down to 19.5 % dry-basis within 3 minutes. Then the paddy was tempered for 30 minutes. Finally, it was cooled by ambient air (temperature and relative humidity of 30 °C and 55-60% respectively) with air velocity of 0.15 m/s for 20 minutes. Quality of paddy in terms of head rice yield and whiteness was acceptable.     

An Experimental Study of the Thermal Performance of a Screw Conveyor Dryer

In the present study drying of fine crystalline solid was carried out in a non-insulated jacketed screw conveyor dryer SCD of 3 m length and 0.072 m screw diameter. It is nitrogen-swept to carry off the evaporated moisture. Dryer performance was evaluated in terms of the final moisture content, heat-transfer coefficient, thermal efficiency and power consumption. From the experimental results it was observed that drying under low pressure gives 92% moisture removal compared to 30-40% using low flow rates of nitrogen. The initial moisture content was in the range of 5 to 6%. Over the parameter range studied, the overall heat transfer coefficient was found to be in the range of 46-102 W/m²K. The average rise in the temperature of the product was 40 to 50°C. Thermal efficiency (based on sensible and latent heat) of the dryer obtained was found to be in the range of 25-62%, typical values obtained in falling rate drying period. Power consumption per metric ton of dried material was found to be a strong function of screw speed and material feed rate, material properties, and drive efficiency.     

Drying Kinetics and Color Retention of Dehydrated Rosehips

Freshly harvested rosehips (Rosa canina L.) were dehydrated in a parallel flow type air dryer at six air temperatures (30, 40, 50, 60, and 70°C) at air velocities of 0.5, 1.0, and 1.5 m/s. Drying air temperature and velocity significantly influenced drying time and energy requirement. Minimum and maximum energy requirement for drying of rosehips were determined as 6.69 kWh/kg for 70°C at 0.5 m/s, and 42.46 kWh/kg for 50°C, 1.5 m/s. In order to reduce drying energy consumption, it is recommended that the drying air velocity must not be more than 0.5 m/s and drying air temperature should be 70°C. In addition, the influence of drying air temperature and air velocity on the color of dried rosehip has been studied. Hunter L, a, b values were used to evaluate changes in the total color difference (ΔE) on dried rosehips. 70°C drying air temperature and 1 m/s air velocity were found to yield better quality product.     

DRYING OF HIGH MOISTURE CONTENT PADDY IN A PILOT SCALE TRIANGULAR SPOUTED BED DRYER

From the successful drying of paddy in a lab-scale triangular spouted bed (TSB), a pilot scale unit with a capacity of 500kg/batch was constructed and used to dry paddy of high moisture contents. The drying tests showed that air temperatures of up to 160°C in the first stage, followed by a lower temperature of 80-100°C in the second stage, can be used to dry paddy from more than 25% down to around 15% (w.b.) without significantly changing grain quality in terms of head rice recovery. Moisture distribution in the pilot-scale TSB was observed to be satisfactorily uniform.     

DRYING OF SOY PULP (OKARA) IN A BED OF INERT PARTICLES

Drying of okara, an insoluble pulp residue waste byproduct of tofu production, was investigated in a continuously moving bed of inert particles subjected to vortex-like motion. The experimental variables in their respective ranges included the mass of Teflon pellets used as inert particles (0.4-1.2 kg), feed rate (0.5-1.4 kg/h), inlet air temperature (100-145°C) and airflow rate (195-271 m³/h). The dryer showed good performance in general and produced dry okara with moisture content ranging from 5 to 33% wb depending upon the operating conditions. The product recovery ranged from 80 to 90% on dry basis in most experiments. The specific water evaporation rate in okara drying increased with increasing of the feed rate and mass of Teflon pellets. However, the specific heat consumption decreased with an increase in the okara feed rate. Results showed that specific heat consumption for okara drying in a bed of inert particles was about 3 to 4 times higher in comparison with that of free water.     

EFFECT OF TEMPERING ON SUBSEQUENT DRYING OF PADDY USING FLUIDISATION TECHNIQUE

Drying and tempering models for paddy drying by a fluidised bed technique have been developed to describe the moisture movement inside a single paddy kernel. The grain shape was considered as a finite cylinder. The internal diffusion is an important contribution to control the drying rate of paddy. The dependence of effective diffusion coefficient on drying temperature can be adequately explained based on Arrhenius form. The parameters of this equation were evaluated in the range of temperatures between 110°C and 170°C by using the regression analysis with 189 experimental drying data. As compared with no tempering, the faster drying rate can be obtained by tempering treatment between drying stages. The effect of degrees of tempering on determining the moisture reduction in the second stage has also been explored. According to the simulation results, a prediction equation of the required tempering time for the tempering index of 0.95 has been established in which the drying air temperature, initial moisture content and drying time are taken into account. The tempering time for 35 min is recommended for the continuous fluidised bed dryers being operated in rice mills.     

Simulation of Recirculating Circular Grain Dryer with Tempering Stage

The diiffusion model describing internal diiffusion of moisture within a grain kernel during drying and tempering stages was incorporated in the cross-flow drying model to simulate the recirculating circular grain dryer with drying and tempering stages. Experiments were conducted on an experimental prototype recirculating circular grain dryer for wheat and rough rice drying. The simulated grain temperature and moisture content were compared with the experimental data of drying wheat and rough rice, the maximum deviation of the outlet grain temperature was 5°C and the maximum deviation ofthe final grain moisture content was 0.3% w.b. The simulating program for recirculating circular grain dryer was used for analyzing the effects of structure parameters and hot air parameters on the dryer performance. Recommendations for design of the recirculating circular grain dryers are drawn from the experiments and simulation.     

Kinematic Model for a Far Infrared Vacuum Dryer

Energy analyses in drying of welsh onion from one source of far infrared radiation at an absolute pressure of 2.6 and 5 kPa were carried out to determine the energy input at which the highest level of efficiency would be attained. The experimental results were used not only to formulate an advanced mathematical model for the prediction of moisture content of onion as a function of drying time but also to study the dryer efficiencies. Less than half of energy input was utilized for evaporating water from the onion. Approximately 73-99% of operating efficiency, which was dependent on the dryer configuration, was converted into radiant energy. The highest radiant efficiency was obtained at 40 W initial power supply, which was equivalent to the source temperature of about 100°C. An 80 W initial electrical power supply at a 10 cm distance of heater from the onion surface showed the highest drying efficiencies. At 80 W power, efficiency decreased with increasing distance from the heater source but at the expense of quality. For optimum drying efficiency without compromising quality, distance of heater from onion surface was proposed to be 10 cm.     

Mechanism of Through Air Drying of Paper: Application in Hybrid Drying

During through air drying the internal sheet drying history develops as a succession of local moisture content profiles in the sheet thickness dimension. These profiles were determined by interrupting the through drying of 180 g/m² 6-ply sheets, then quickly delaminating and determining the moisture content of each 30 g/m² ply. On the through flow inlet side of the sheet, large moisture differences, about 0.4-0.6 kg/kg dry per 30 g/m² ply, develop and move into the interior of the sheet provided that local moisture content is in the range 0.45-1.75 kg/kg. On the through flow exit side, moisture gradients only become significant for moisture content below about 1.25 kg/kg. From the through flow exit side of the sheet much of the water is removed by diffusion to the flow entry side where most evaporation into the through flow occurs. The kinetics of through drying reflect the interaction between these two mechanisms, local evaporation into the through flow and thickness direction diffusion. The moisture diffusivity-moisture content relation controls this balance. In any combination with cylinder drying to give some kind of hybrid dryer, through drying should be at the dry end where air permeability is highest and cylinder drying rate is lowest.