Influence of Post Hot Isostatic Pressing on the Microstructural Development and Critical Current Density of YBa2Cu3O7-x

Samples of nearly theoretical density are produced by post hot isostatic pressing (post-HIP) of presintered YBa₂Cu₃O_7-x using argon as the pressure medium. The hot isostatically pressed samples show improved values for critical current density at 77 K. Experimental aspects of post-HIP are described, and microstructural development of YBa₂Cu₃O_7-x during sintering and post-HIP is discussed.     

Hot Isostatic Pressing of YBa2Cu3O7-x

Hot isostatic pressing (HIPing) with an oxygen donor was studied as a method for processing bulk superconductors. Superconducting powder was derived from the calcination of nitrated Y₂O₃, CuO, and BaCO₃ powder. The powder was HIPed using pressures of 69, 138, and 207 MPa at 820°C. BaO₂ was used as an oxygen donor during HIPing. The density, hardness, and Young's modulus of HIPed samples were higher than those of sintered control samples. Superconducting transition temperatures > 92 K were achieved without post-HIP annealing of the samples in oxygen.     

Water Corrosion of YBa2Cu3O7−δ Superconductors

Solid-state sintering was used to make YBa₂Cu₃O_7−δ superconducting bulk materials. Corrosion of the YBa₂Cu₃O_7−δ superconductor material was investigated in a humid environment. The superconducting materials exhibited significant corrosion after 4 h at 80° and 100% relative humidity. A grain-boundary phase was formed, and the percent superconducting phase in the material decreased by approximately 60%. The transition temperature (T_c) decreased with corrosion time. After 2 h of corrosion, T_c decreased from 87 to 81 K.     

Transmission Electron Microscopy Study on the Annealing of YBa2Cu3O7-δ

Annealing in oxygen-rich atmosphere at temperatures between 400° and 600°C is an important step in the manufacture of superconducting YBa₂Cu₃O_7-δ. The symmetry of the orthorhombic phase requires that if more than one type of twin plane is present within a grain, a distorted region should exist inside the multiple twinned grain. This distorted region hinders the tetragonal-to-orthorhombic transformation and may account for some retained tetragonal phase inside an otherwise orthorhombic grain. A physical model is presented describing the formation of such regions and their eventual transformation into low-angle grain boundaries after long annealing. Extended annealing at intermediate temperatures apparently leads to the formation of planar faults in off-stoichiometric samples. Transmission electron microscope image contrast and energy dispersive X-ray analyses of highly defective regions suggest these defects are CuO _x ( x = 1, 2) extra layers. These extra layers tend to form near grain boundaries or free surfaces, where oxygen is readily available.     

Novel Solution-Soaking Method for Adding Dopants to YBa2Cu3O7−x to Achieve Higher Sintered Densities

YBa₂Cu₃O_7−x was doped with various metal ions by a new technique in which a pellet (after binder burnout) was soaked in a solution containing the appropriate ions and then dried. The sintered density of the treated pellets depended on the dopant in the solution, and in many cases it was much higher than that obtained for pure YBa₂Cu₃O_7−x (93% to 96% as compared with 85% to 90%). A study of the microstructure revealed that, in those cases where higher sintered densities were obtained, the grain size was much smaller. The grain morphology, however, did not change. It is likely that the high concentration of dopant adsorbed on the grain surface during solution soaking enhanced the rate of sintering.     

Experimental and Thermodynamic Study of Nonstoichiometry in 〈YBa2Cu3O7-x〉

The dependence of the nonstoichiometry of 〈YBa₂Cu₃O_7−x〉 (solid) has been studied over 5 orders of magnitude in oxygen pressure and from 573 to 1173 K. Hydrogen-reduction methods for determining the absolute oxygen to-metal ratio were developed. The resulting data were used to derive a chemical thermodynamic representation of the experimental variables. The data were used to derive a chemical thermodynamic representaltion of the experimental variables. The data were also compared with several other investigations to indentify the selfconsistent sets of data. The present data and thermodynamic data from the literature were correlated on an Ellingham diagram.     

Superplastic Deformation in Fine-Grained YBa2Cu3O7−x

The superplastic behavior of YBa₂Cu₃O_{7− x} ceramic superconductors was studied. Large compressive deformation over 100% strain was measured in the temperature range of 775°–875°C, with a strain rate of 1 × 10⁻⁵ to 1 × 10⁻³/s, and a grain size of 0.5–1.4 μm. The nature of the deformation was investigated in terms of three deformation parameters: the stress exponent ( n ), the grain size exponent ( p ), and the activation energy ( Q ). The measured values of these parameters were n = 2 ± 0.3, p = 2.7 ± 0.7, and Q = 745 ± 100 kJ/mol. With the aid of the deformation map, the deformation mechanism was identified as grain boundary sliding accommodated by grain boundary diffusion. The conclusion is consistent with the microstructural observations made by SEM and TEM: the invariance of equiaxed grain shape, the absence of significant dislocation activity, no grain boundary second phases, and no significant texture development.     

Defect Equilibria and Transport in YBa2Cu3O7-x at Elevated Temperatures: III, Defect Model and Conductivity Mechanism

Based on the measurements of electrical conductivity and thermopower (Seebeck coefficient) as a function of oxygen partial pressure, the defect structure and corresponding conduction mechanisms at elevated temperatures are considered for the Y-Ba-Cu-O (1:2:3) system. It has been postulated that the simple hopping model is not applicable to YBa₂Cu₃O_7-x. A modified conduction hopping mechanism has been proposed and equations describing the mobility of charge carriers in the studied system are derived. The most important advantage of the present model, in comparison to previous models, involves considering interactions between both electrons and electron holes and the resulting effect on their mobility terms. The observed departure of experimental data from the Heikes formula is explained by a very high concentration of defects and resulting substantial interactions between the defects which must be taken into account. The proposed transport model exhibits good agreement with experimental data of nonstoichiometry and the presently determined electrical conductivity and thermopower. It has been argued that the charge transfer mechanism depends substantially on the oxygen partial pressure and resulting oxygen content in the oxide lattice.     

Hot Isostatic Pressing of YBa2Cu3O7-δ and YBa2Cu3O7–δ/Ag Composites

Hot isostatic pressing (HIP) can be used to produce fully dense shapes of high-temperature ceramic superconductors. Densification modeling of monolithic YBa₂Cu₃O_7-δ and the composite YBa₂Cu₃O_7-δ/Ag systems allows an understanding of the HIP process and has led to the development of successful protocols for HIP of these materials. Ag metal is the best encapsulation material found for both systems. HIP of monolithic YBa₂Cu₃O_7-δ requires a slow ramp of pressure in order to prevent decomposition into more basic oxides such as Y₂BaCuO₅ and CuO. HIP of composite YBa₂Cu₃O_7-δ/Ag requires careful powder processing to obtain dense material with a fine dispersion of Ag.     

Defect Equilibria and Transport in YBa2Cu3O7-x at Elevated Temperatures: II, Nonstoichiometry

Aspects of nonstoichiometry for the Y-Ba-Cu (1: 2: 3) system are considered. The general formula YBa₂Cu₃O_7-x has been assumed for considerations of nonstoichiometry in 1: 2:3 oxide cuprates. Assuming that copper ions may occupy different lattice positions (independently of their valency), the equilibrium constants for oxygen intercalation were determined:     

Formation of Grain-Boundary Carbon-Containing Phase During Annealing of YBa2Cu3O6+x

In situ annealing studies of YBa₂Cu₃O_6+x performed in an optical hot stage revealed that, at temperatures ∧450°, localized melting occurred. On subsequent cooling, a discrete second phase was observed at the YBa₂Cu₃O_6+x grain boundaries. Quantitative chemical analysis using X-ray wavelength dispersive spectroscopy indicated that the second phase was composed of a barium oxycarbonate. The source of the carbon in the second phase was identified to be CO₂ in the atmosphere.     

Type II Magnetic Levitation on Sinter-Forged YBa2Cu3Ox Superconductor

Submicrometer powder of singlephase YBa₂Cu₃O_x (YBC), prepared from nitrate salts, were free-sintered and sinter-forged at 1223 K. The levitation force on magnets exerted by the superconductor was found to depend on the thickness of the superconductor, the shear strain imposed during sinter-forging, and the time and temperature of the high-pressure oxygen anneal after sinter-forging. The first result is direct proof of the type II nature of the YBC superconductor. In the second experiment a shear strain of 300% increased the levitation force by a factor of 3. The third result confirmed that YBC transforms to the tetragonal structure at 1223 K, which must be restored to the orthorhombic structure by annealing at lower temperature. Optimum results were obtained when the specimens were annealed in pressurized oxygen (3 MPa) for 50 h at 673 K.     

Yttrium α-Sialon Ceramics by Hot Isostatic Pressing and Post-Hot Isostatic Pressing

Dense α-sialon materials were produced by hot isostatic pressing (HIP) and post-hot isostatic pressing (post-HIP) using compositions with the formula Y _x (Si_{12–4.5 x} , Al_{4.5 x} )-(O_{1.5 x} ,N_{16–1.5 x} ) with 0.1 ≤ x ≤ 0.9 and with the same compositions with extra additions of yttria and aluminum nitride. X-ray diffraction analyses show how the phase content changes from large amounts of β-sialon ( x = 0.1) to large amounts of α-sialon ( x = 0.4) and increasing amounts of mellilite and sialon polytypoids ( x = 0.8). Samples HIPed at 1600°C for 2 h contained unreacted α-silicon nitride, while those HIPed at 1750°C for 1 h did not. This could be due to the fact that the time is to short to achieve equilibrium or that the high pressure (200 MPa) prohibits α-sialon formation. Sintering at atmospheric pressure leads to open porosity for all compositions except those with excess yttria. Therefore, only samples with excess yttria were post-HIPed. Microstructrual analyses showed that the post-HIPed samples had the highest α-sialon content. A higher amount of α-sialon and subsequently a lower amount of intergranular phase were detected at x = 0.3 and x = 0.4 in the post-HIPed samples in comparison to the HIPed. The hardness (HV10) and fracture toughness ( K _IC) did not differ significantly between HIPed and post-HIPed materials but vary with different x values due to different phase contents. Measurements of cell parameters for all compositions show a continuous increase with increasing x value which is enhanced by high pressure at high x values.     

Vapor Pressure of Barium and Copper Components in YBa2Cu3O7−x Superconductor Ceramics

Purified air is passed over a specimen of YBa₂Cu₃O_{7– x} at 890°C; the vaporized substances are condensed in a pure alumina tube, then subjected to inductively controlled plasma analysis. Vapor pressure values of 2.5 × 10⁻⁵ Pa for BaO( g ), 1.2 × 10⁻⁴ Pa for Cu( g ), and 2.2 × 10⁻⁵ Pa for CuO( g ) are obtained under 2.1 × 10⁴ Pa (0.21 bar) of oxygen pressure. No Y vapor is detected at this temperature.     

Effects of Temperature and Strain Rate on the Plastic Deformation of Fully Dense Polycrystalline Y1Ba2Cu3O7−x Superconductor

The knowledge of the steady-state stress for plastic deformation as a function of temperature and strain rate is essential for hot-forming superconducting material into commercially useful shapes. In this paper, results are presented on the experimental determination of the rheology of fully dense polycrystalline Y₁Ba₂Cu₃O_7−x superconducting material at temperatures ranging from 750° to 950°C and strain rates of 10⁻⁴, 10⁻⁵, and 10⁻⁶ s⁻¹. The data are best fitted by a power law: ε(s⁻¹)=8.9 × 10⁻¹⁷. (s⁻¹) σ^2.5 (Pa) exp [−2.01 × 10⁵(J·mol⁻¹)|RT]. X-ray analysis shows that the superconducting material retains its phase composition after nearly 70% total strain of the sample. A strong anisotropy in the resistivity of the deformed samples is observed because of the development of a preferred orientation of the a or b axis of Y₁Ba₂Cu₃O_7−x orthorhombic perovskite single crystals perpendicular to the principal maximum compressive stress.     

Simultaneous Thermogravimetry and Evolved-Gas Analysis of YBa2Cu3O7 and LaBa2Cu3O7 Superconductors

Concurrent thermogravimetry (TG) and evolved-gas analysis (EGA) were done for YBa₂Cu₃O_7-z and LaBa₂Cu₃-O_7-z superconductors. The sample weights were monitored by thermobalance and the evolved O₂ and CO₂ species were monitored by quadruple mass spectrometer (QMS). No diffraction peak for the impurity phase containing a carbonate group was observed in the X-ray diffraction patterns for these samples, but the release of CO₂ was detected by EGA. CO₂ gas began to evolve from YBa₂Cu₃O_7-z at 543°C and from LaBa₂Cu₃O_7-z at 692°C. Preparation of high-quality YBa₂Cu₃O_7-z and LaBa₂Cu₃O_7-z superconductors is discussed on the basis of results of these thermal analyses.     

Hot Deformation of YBa2Cu3O7-δ and Composite YBa2Cu3O7-δ/Ag

The response of ceramic superconductors and ceramic composites to compressive stresses at high temperatures has been examined. Monolithic YBa₂Cu₃O_7-δ and composite YBa₂Cu₃O₇-δ₆/Ag were tested at constant true strain rates from 10^-6 to 10^-3 s^-1 at temperatures from 800° to 950°C. Fine-grained monolithic YBa₂Cu₃O_7-δ appears to have a regime of superplastic deformation between temperatures of 850° and 950°C at strain rates from 10^-6 to 10^-4 S^-1. The addition of 20 vol% Ag to a coarser-grained material enhances the ductility of the ceramic and lowers the flow stress by a factor of 3 to 10. However, there is no evidence of superplasticity in the composite material in the range of temperature and strain rate where it was tested.     

Thermopower of YBa2Cu3O7-δ–Ag Composites

The percolation behavior of normal-state thermopower, resistivity, and superconductivity have been studied in YBa₂Cu₃O_7-δ─Ag (YBCO─Ag) composite systems. The normal-state resistivity and thermopower show a percolation threshold at a Ag volume fraction ( V _Ag) of 20% to 30%, whereas the superconducting network shows a threshold at a V _Ag of ≅70% to 80%. The results obtained from this study show that the YBCO─Ag composite obtained from Ag₂O and YBCO powders is uniformly distributed with Ag and YBCO remaining as separate phases without changing their characteristics. The measurements of thermopower indicate that the normal-state thermopower and phonon-drag thermopower are affected by the Ag addition. The stability of YBCO is increased when it is in composite form.