Performance improvement mechanisms of P3HT:PCBM inverted polymer solar cells using extra PCBM and extra P3HT interfacial layers

A novel P3HT:PCBM inverted polymer solar cell (IPSC) was fabricated and investigated. An extra PCBM and an extra P3HT interfacial layers were inserted into the bottom side and the top side of the P3HT:PCBM absorption layer of the IPSCs to respectively enhance electron transport and hole transport to the corresponding electrodes. According to the surface energy, X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) measurement results, the extra PCBM interfacial layer could let more P3HT to form on the top side of the P3HT:PCBM blends. It revealed that the non-continuous pathways of P3HT in the P3HT:PCBM absorption layer could be reduced. Consequently, the carrier recombination centers were reduced in the absorption layer of IPSCs. The power conversion efficiency (PCE) of the P3HT:PCBM IPSCs with an extra PCBM interfacial layer greatly increased from 3.39% to 4.50% in comparison to the P3HT:PCBM IPSCs without an extra PCBM interfacial layer. Moreover, the performance of the P3HT:PCBM IPSCs with an extra PCBM interfacial layer could be improved by inserting an extra P3HT interfacial layer between the absorption layer and the MoO₃ layer. The PCE of the resulting IPSCs increased from 4.50% to 4.97%.     

Flexible solar cells based on PCBM/P3HT heterojunction

[6,6]-phenyl-C61-butyric acid methyl ester (PCBM) / poly (3-hexylthiophene) (P3HT) heterojunction has not only the absorption in ultraviolet light for PCBM,but also the absorption in visible light for P3HT, which widens the incident light harvest range, improving the photoelectrical response of hybrid solar cell effectively.Using conducting polymers blend heterojunetion consisting of C60 derivatives PCBM and P3HT as charge carrier transferring medium to replace I3-/I- redox electrolyte and dye, a novel flexible solar cell was fabricated in this study.The influence of PCBM/P3HT mass ratio on the photovoltaic performance of the solar cell was also studied.flexible solar cell achieved a light-to-electric energy conversion efficiency of 1.04%, an open circuit voltage fill factor (FF) of 0.46.     

Comparative study of spectral and morphological properties of blends of P3HT with PCBM and ICBA

We report a comparative study on spectral and morphological properties of two blend systems for polymer solar cells: the donor material poly(3-hexylthiophene) (P3HT) in combination with the acceptor material of either [6,6]-phenyl-C₆₁ butyric acid methyl ester (PCBM) or indene-C₆₀ bisadduct (ICBA) that was reported to enhance efficiencies of polymer solar cells. Optical microscopy and grazing incidence X-ray scattering reveal the stronger tendency of PCBM to from larger and more ordered domains/grains than ICBA either in pure or blend films. Compared to PCBM, the presence of ICBA also substantially perturbs the organization and longer-range ordering of P3HT in increasing the ICBA ratio in blends. With larger and more ordered phase-separated domains, the P3HT/PCBM blend films exhibit significant optical scattering at higher PCBM ratios. Yet, such optical scattering is not significant for P3HT/ICBA blends (even with high ICBA ratios). Overall, results here suggest the reported higher efficiencies of P3HT/ICBA solar cells (vs. P3HT/PCBM cells) cannot be attributed to larger and/or more ordered phase-separated donor–acceptor domains and other characteristics play more important roles in this case.     

Modeling of optimum size and shape for high photovoltaic performance of poly(3-hexylthiophene) nanopore in interdigitated bilayer organic solar cells

The interdigitated design for donor–acceptor in solar cell has been studied in some detail, but the optimum size and shape leading to direct enhancement in nanopore (or nanopillar) structure is still not well understood. Here, we demonstrate a modeling method to forecast the optimum size and shape for poly(3-hexylthiophene) (P3HT) nanopores in interdigitated P3HT: [6, 6]-phenyl C₆₁ butyric acid methyl ester (PCBM) photovoltaic device, based on experimental results of P3HT:PCBM bilayer solar cell. In our analysis, the energy generated at unit nanopore is supposed to the same as the one generated at infinite point of P3HT:PCBM bilayer solar cell with variable layer thickness. A definitive function in terms of a radius of unit nanopore with various shapes is established, substituting a regression function derived from the results of power conversion efficiency in bilayer solar cell. Interpreting the function, we finally showed that the effective radius for P3HT nanopores with rectangular or cylinder, cut-cone, cone shape should be less than 135, 53, 2 nm respectively.     

Optical,electrical and mechanical properties of indium tin oxide on polyethylene terephthalate substrates: Application in bulk-heterojunction polymer solar cells

We investigated optical, electrical and mechanical properties of indium tin oxide (ITO) on flexible polyethylene terephthalate (PET) substrate, considering bulk-heterojunction (BHJ) polymer solar cells applications. Encapsulation of flexible solar cells with the architecture PET/ITO/PEDOT:PSS/P3HT:PCBM (or P3HT:PCBM:AZ-NDI-4)/Al was done by direct brush-painting with nail enamel. Active cell layer blends of [6,6]-phenyl C₆₁ butyric acid methyl ester (PCBM) with regioregular or regiorandom poly(3-hexylthiophene-2,5-diyl) (P3HT) were applied. Additionally for this role the mixture of regioregular P3HT:PCBM with naphthalene diimide–imine with four thiophene rings AZ-NDI-4 was tested. Obtained photovoltaic (PV) and optical (UV–vis) results of the flexible polymer solar cells were compared with the same architecture of devices on the glass/ITO substrate.     

Photo stability enhancement of Poly(3-hexylthiophene)-PCBM nanocomposites by addition of multi walled carbon nanotubes under ambient conditions

Poly(3-hexylthiophene)-Phenyl-C61-butyric acid methyl ester (P3HT–PCBM) composites find wide application in optoelectronic devices, especially bulk-hetero junction (BHJ) solar cells. These composites, even though could give efficient polymer solar cells with ∼4–5% power conversion efficiencies (PCE), a major problem of photo stability is associated with it and remains unsolved. P3HT–PCBM composite was found to be degrading on irradiation with ultraviolet radiation or a solar simulator providing AM1.5G illumination (1000 W m^–2, 72 ± 2 °C or 330 W m⁻², 25 °C), in presence of oxygen and moisture. Here, we have studied the photo stability of P3HT–PCBM under ambient conditions and showed that a new ternary composite, P3HT–PCBM–MWCNT (multi walled carbon nanotube) has superior photo stability even on extended UV–Vis exposure. A total of 7% (w/w) PCBM and 3% (w/w) MWCNT with respect to P3HT resulted in optimum stability. UV–Visible and fluorescence spectral analysis have been used to study the photo stability, both in solution state and solid/film state. Transmission electron micrograph (TEM) along with selected area electron diffraction (SAED) pattern and Field Emission Scanning Electron Microscopy (FE-SEM) micrographs have been used to show the well coating of MWCNT on P3HT–PCBM composite. Since MWCNT is one of the very important carbon based nanomaterial with several supreme characteristics, this new ternary composite has great importance for optoelectronic applications.     

Annealing‐Free High Efficiency and Large Area Polymer Solar Cells Fabricated by a Roller Painting Process

Polymer solar cells are fabricated by a novel solution coating process, roller painting. The roller‐painted film – composed of poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) – has a smoother surface than a spin‐coated film. Since the roller painting is accompanied by shear and normal stresses and is also a slow drying process, the process effectively induces crystallization of P3HT and PCBM. Both crystalline P3HT and PCBM in the roller‐painted active layer contribute to enhanced and balanced charge‐carrier mobility. Consequently, the roller‐painting process results in a higher power conversion efficiency (PCE) of 4.6%, as compared to that for spin coating (3.9%). Furthermore, annealing‐free polymer solar cells (PSCs) with high PCE are fabricated by the roller painting process with the addition of a small amount of octanedi‐1,8‐thiol. Since the addition of octanedi‐1,8‐thiol induces phase separation between P3HT and PCBM and the roller‐painting process induces crystallization of P3HT and PCBM, a PCE of roller‐painted PSCs of up to 3.8% is achieved without post‐annealing. A PCE of over 2.7% can also be achieved with 5 cm² of active area without post‐annealing.     

Time‐Dependent Morphology Evolution by Annealing Processes on Polymer:Fullerene Blend Solar Cells

Changes in the nanoscale morphologies of the blend films of poly (3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM), for high‐performance bulk‐heterojunction (BHJ) solar cells, are compared and investigated for two annealing treatments with different morphology evolution time scales, having special consideration for the diffusion and aggregation of PCBM molecules. An annealing condition with relatively fast diffusion and aggregation of the PCBM molecules during P3HT crystallization results in poor BHJ morphology because of prevention of the formation of the more elongated P3HT crystals. However, an annealing condition, accelerating PCBM diffusion after the formation of a well‐ordered morphology, results in a relatively stable morphology with less destruction of crystalline P3HT. Based on these results, an effective strategy for determining an optimized annealing treatment is suggested that considers the effect of relative kinetics on the crystallization of the components for a blend film with a new BHJ materials pair, upon which BHJ solar cells are based.     

Non-peripheral octahexylphthalocyanine doping effects in bulk heterojunction polymer solar cells

The improvement of long-wavelength sensitivity in bulk heterojunction organic thin-film solar cells based on poly(3-hexylthiophene) (P3HT) by the addition of the soluble phthalocyanine derivative, 1,4,8,11,15,18,22,25-octahexylphthalocyanine (C6PcH₂) is reported. C6PcH₂ possesses near-infrared absorption and can be mixed with a P3HT:1-(3-methoxy-carbonyl)-propyl-1-1-phenyl-(6,6)C61 (PCBM) bulk heterojunction active layer. By doping C6PcH₂, the photosensitivity in the long-wavelength region was improved, and the energy conversion efficiency reached 3.0% at a composition ratio of P3HT:C6PcH₂:PCBM = 10:3:10. We discuss the principle of photoconversion in the bulk heterojunction solar cell based on the P3HT:C6PcH₂:PCBM active layer by taking into consideration the existence of both highly ordered P3HT domains and hexagonal columnar structures of C6PcH₂, and the microphase separation of P3HT and C6PcH₂ in the active layer.     

Enhanced performance of inverted organic solar cell by a solution-based fluorinated acceptor doped P3HT:PCBM layer

An inverted organic solar cell based on strong electron acceptor 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4-TCNQ) doped poly (3-hexylthiophene) P3HT: [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM) was fabricated to figure out the p-type doping effect on the device performance. It was found that the doping concentration played a critical role on the electrical output of the devices. An enhanced power conversion efficiency (PCE) of 4.22% was achieved, in comparison of PCE of 3.68% for the device based on pristine P3HT:PCBM. The topography morphology of the active film, the hole mobility, the ultraviolet–visible absorption spectrum, the photoluminescence (PL) lifetime and the Fermi energy level of P3HT film with and without F4-TCNQ doping were characterized to investigate the doping effect. The measured results indicated that the hole mobility and absorption of P3HT film was slightly modified with F4-TCNQ doping. On the contrary, the active film morphology, the PL lifetime and the Fermi energy level of P3HT changed dramatically with doping. It was found that F4-TCNQ preferred to approach to the air/liquid interface during the solvent dry process, leading to F4-TCNQ-rich upper layer due to its low surface energy. The layer with proper thickness between anode and active layer dramatically improve the interface contact, resulting in the enhanced device performance.     

Abrupt Morphology Change upon Thermal Annealing in Poly(3‐Hexylthiophene)/Soluble Fullerene Blend Films for Polymer Solar Cells

The in situ morphology change upon thermal annealing in bulk heterojunction blend films of regioregular poly(3‐hexylthiophene) (P3HT) and 1‐(3‐methoxycarbonyl)‐propyl‐1‐phenyl‐(6,6)C₆₁ (PCBM) is measured by a grazing incidence X‐ray diffraction (GIXD) method using a synchrotron radiation source. The results show that the film morphology—including the size and population of P3HT crystallites—abruptly changes at 140 °C between 5 and 30 min and is then stable up to 120 min. This trend is almost in good agreement with the performance change of polymer solar cells fabricated under the same conditions. The certain morphology change after 5 min annealing at 140 °C is assigned to the on‐going thermal transition of P3HT molecules in the presence of PCBM transition. Field‐emission scanning electron microscopy measurements show that the crack‐like surface of blend films becomes smaller after a very short annealing time, but does not change further with increasing annealing time. These findings indicate that the stability of P3HT:PCBM solar cells cannot be secured by short‐time annealing owing to the unsettled morphology, even though the resulting efficiency is high.     

On the stability of the electrical and photoelectrical properties of P3HT and P3HT:PCBM blends thin films

New photoelectrical properties of poly(3-hexylthiophene-2,5-diyl), highly regioregular (P3HT): Methanofullerene Phenyl-C₆₁-Butyric-Acid-Methyl-Ester [60] PCBM films were putted in evidence. For the first time the electrical conductivity dependencies on temperature in dark and under different illuminations were studied for the P3HT and P3HT:PCBM blend films. These dependencies shows reversible processes and a high sensitivity of the P3HT and P3HT:PCBM to light. The decrease of the resistivity at the exposure to light is of 18% for P3HT films and of 20% for P3HT:PCBM blend films, for a irradiation under 0.5 W/m² white light at room temperature. By adding the fullerene molecules, in the 1:0.8 polymer:fullerene ratio, the electrical resistivity at room temperature of the blend films decrease compared to the polymer film by 40% in dark, and by 68% under 250 W/m² white light irradiance.The decrease of the resistivity with the temperature is more pronounced in the presence of light indicating a photon activated process.The existence of the open circuit voltage was evidenced even for planar geometry photodiodes and the values of the open circuit voltage under 1000 W/m² solar light illumination are coherent with the difference between the work functions of the electrodes.     

Cover Picture: Tuning the Dimensions of C60‐Based Needlelike Crystals in Blended Thin Films (Adv. Funct. Mater. 6/2006)

A new ordered structure of the C₆₀ derivative PCBM is obtained in thin films based on the blend PCBM:P3HT, as detailed by Swinnen, Manca, and co‐workers on p. 760. Needlelike crystalline PCBM structures, whose dimensions and spatial distribution ca be tuned by adjusting the blend ratio and annealing conditions, are formed. In typical solar‐cell applications of these blended films, these results indicate that during long‐term operation under normal conditions (50–70 °C) morphology changes and a decrease in cell performance could occur. A new ordered structure of the C₆₀ derivative PCBM ([6‐6]‐phenyl C₆₁‐butyric acid methyl ester) is obtained in thin films based on the blend PCBM:regioregular P3HT (poly(3‐hexylthiophene)). Rapid formation of needlelike crystalline PCBM structures of a few micrometers up to 100 μm in size is demonstrated by submitting the blended thin films to an appropriate thermal treatment. These structures can grow out to a 2D network of PCBM needles and, in specific cases, to spectacular PCBM fans. Key parameters to tune the dimensions and spatial distribution of the PCBM needles are blend ratio and annealing conditions. The as‐obtained blended films and crystals are probed using atomic force microscopy, transmission electron microscopy, selected area electron diffraction, optical microscopy, and confocal fluorescence microscopy. Based on the analytical results, the growth mechanism of the PCBM structures within the film is described in terms of diffusion of PCBM towards the PCBM crystals, leaving highly crystalline P3HT behind in the surrounding matrix.     

Effects of exciton blocking layer and cathode electrode work function on the performance of polymer solar cells

In this study the effects of some important processing and post-processing treatments on the performance of poly(3-hexylthiophene-2,5-diyl) (P3HT):[6,6]-phenyl-C₆₁-butyric acid methyl ester ([60]PCBM) solar cells were investigated. These parameters included the active layer film formation period, thermal annealing, electrical treatment, cathode work function modification, and exciton blocking layer type and thickness. Polymer bulk heterojunction solar cells having a glass/indium tin oxide (ITO)/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)/P3HT:PCBM/(Ca or LiF)/Al structure were fabricated. The morphology of the active layer was investigated using atomic force microscopy. The results showed that the morphology state of the active layer exactly after spin coating process was very important parameter, which could dictate different responses of solar cells to a certain treatment. Using solvent additives to prolong the film formation period and storing in small dish could reach the morphology of the active layer near its best state in which there was no need to apply common post-treatment processes. A thickness at about 20 nm was required for Ca layer to effectively act as exciton blocking layer while LiF with 1 nm thickness worked better.     

High‐Resolution Spectroscopic Mapping of the Chemical Contrast from Nanometer Domains in P3HT:PCBM Organic Blend Films for Solar‐Cell Applications

A high‐resolution near‐field spectroscopic mapping technique is successfully applied to investigate the influence of thermal annealing on the morphology of a poly(3‐hexylthiophene) and [6,6]‐penyl‐C₆₁ butyric acid methyl ester (P3HT:PCBM) blend film. Based on the simultaneously recorded morphological and spectroscopic information, the interplay among the blend film morphology, the local P3HT:PCBM molecular distribution, and the P3HT photoluminescence (PL) quenching efficiency are systematically discussed. The PL and Raman signals of the electron donor (P3HT) and acceptor (PCBM) are probed at an optical resolution of approximately 10 nm, which allows the chemical nature of the different domains to be identified directly. In addition, the local PL quenching efficiency, which is related to the electron transfer from P3HT to PCBM, is quantitatively revealed. From these experimental results, it is proposed that high‐resolution near‐field spectroscopic imaging is capable of mapping the local chemical composition and photophysics of the P3HT:PCBM blends on a scale of a few nanometers.     

Effects of incorporation of copper sulfide nanocrystals on the performance of P3HT: PCBM based inverted solar cells

It has been reported that performance of bulk heterojunction organic solar cells can be improved by incorporation of an additive like metal and semiconducting nanoparticles in the active layer. Here in, we have synthesized Cu₂S nanocrystals (NCs) by chemical route and studied its dispersion in poly (3-hexylthiophene) [6, 6]-phenyl C61-butyric acid methyl ester (P3HT: PCBM) matrix. Variation in the performance parameters with change in the concentration of Cu₂S NCs into the P3HT: PCBM matrix has also been studied and it was found that the inverted geometry device with concentration of 20 wt% of Cu₂S NCs and having the structure ITO/ZnO (NPs)/P3HT: PCBM:Cu₂S NCs/MoO₃/Al has shown maximum efficiency of 3.39% which is more than 100% increase in comparison with devices without Cu₂S NCs. Photoluminescence measurements studies unveiled that the incorporation of Cu₂S NCs into a P3HT: PCBM matrix has helped in quenching photoluminescence which suggests more effective exciton dissociation at the interfaces between the P3HT and PCBM domains. The Nyquist plots obtained from impedance spectroscopy at 1 V bias in the dark has suggested the effective lifetime and global mobilities for P3HT: PCBM as 0.267 ms and 1.17 × 10⁻³ cm²/V-S and for P3HT: PCBM:Cu₂S NCs (20 wt%) systems as 0.156 ms and 2.02 × 10⁻³ cm²/V-S respectively. Based on observed photoluminescence quenching, calculated effective lifetime and global mobility, we have tried to explain the possible reason for improvement in the efficiency with the very well dispersion of Cu₂S NCs into the P3HT: PCBM matrix.     

Charge transport properties of bulk-heterojunction organic solar cells investigated by displacement current measurement technique

We have investigated charge transport properties of bulk-heterojunction (BH) solar cells in which P3HT (Poly(3-hexylthiophene)) and PCBM ([6,6]-phenyl-C₆₁-butyric acid methyl ester) are used as the active layer, by using the displacement current measurement (DCM) method. In order to investigate the charge transport properties of the BH solar cells, we fabricated a dedicated device that consists of P3HT and PCBM, and used the DCM method to measure the charge distribution of the devices with different composition ratios of P3HT and PCBM. DCM data suggested that a BH film with 50 wt% of PCBM exhibits a preferable charge transport property suited for BH solar cells. We confirmed that the DCM results are consistent with the measured performance of the BH solar cells, indicating that the DCM method is a simple and effective method for optimizing the structure of BH solar cells as well as other electronic devices composed of binary materials.     

Elaboration of P3HT/CNT/PCBM Composites for Organic Photovoltaic Cells

This Full Paper focuses on the preparation of single‐walled or multi‐walled carbon nanotube solutions with regioregular poly(3‐hexylthiophene) (P3HT) and a fullerene derivative 1‐(3‐methoxycarbonyl) propyl‐1‐phenyl[6,6]C₆₁ (PCBM) using a high dissolution and concentration method to exactly control the ratio of carbon nanotubes (CNTs) to the P3HT/PCBM mixture and disperse the CNTs homogeneously throughout the matrix. The CNT/P3HT/PCBM composites are deposed using a spin‐coating technique and characterized by absorption and fluorescence spectroscopy and by atomic force microscopy to underline the structure and the charge transfer between the CNTs and P3HT. The performance of photovoltaic devices obtained using these composites as a photoactive layer mainly show an increase of the short circuit current and a slight decrease of the open circuit voltage which generally leads to an improvement of the solar cell performances to an optimum CNT percentage. The best results are obtained with a P3HT/PCBM (1 : 1) mixture with 0.1 wt % multi‐walled carbon nanotubes with an open circuit voltage (V_oc) of 0.57 V, a current density at the short‐circuit (I_sc) of 9.3 mA cm^–2 and a fill factor of 38.4 %, which leads to a power conversion efficiency of 2.0 % (irradiance of 100 mW cm^–2 spectroscopically distributed following AM1.5).     

Understanding the role of organic polar solvent induced nanoscale morphology and electrical evolutions of P3HT:PCBM composite film

We investigated the effect of organic polar solvent on the properties of [6,6]-phenyl-C₇₁-butyric acid methyl ester (PCBM) films and poly(3-hexylthiophene) (P3HT):PCBM blend films employed as active layer in organic photovoltaic. The nanoscale morphology and the electrical characteristics of the P3HT:PCBM film can be controlled through organic polar solvent exposure, which exhibited with a short-circuit current density of 8.64 mA/cm², an open circuit voltage of 0.63 V, and a power conversion efficiency of 3.29% under AM 1.5 illumination with a light intensity of 100 mW/cm². By exposing the active layer films to organic polar solvent a favorable phase separation in the P3HT:PCBM films is obtained. The improved power conversion efficiency can be to the high conductivity and high surface area of the P3HT:PCBM layer treated with organic polar solvent.     

The Effect of Ageing on Exciton Dynamics,Charge Separation,and Recombination in P3HT/PCBM Photovoltaic Blends

A study of how light‐induced degradation influences the fundamental photophysical processes in the active layer of poly(3‐hexylthiophene)/[6,6]‐phenyl C₆₁‐butyric acid methyl ester (P3HT/PCBM) solar cells is presented. Non‐encapsulated samples are systematically aged by exposure to AM 1.5 illumination in the presence of dry air for different periods of time. The extent of degradation is quantified by the relative loss in the absorption maximum of the P3HT, which is varied in the range 0% to 20%. For degraded samples an increasing loss in the number of excitons within the P3HT domains is observed with longer ageing periods. This loss occurs rapidly, within the first 15 ps after photoexcitation. A more pronounced decrease in the population of polarons than excitons is observed, which also occurs on a timescale of a few picoseconds. These observations, complemented by a quantitative analysis of the polaron and exciton population dynamics, unravel two primary loss mechanisms for the performances of aged P3HT/PCBM solar cells. One is an initial ultrafast decrease in the polaron generation, apparently not related to the exciton diffusion to the polymer/fullerene interface; the second, less significant, is a loss in the exciton population within the photoexcited P3HT domains. The steady‐state photoinduced absorption spectra of degraded samples exhibits the appearance of a signal ascribed to triplet excitons, which is absent for non‐degraded samples. This latter observation is interpreted considering the formation of degraded sites where intersystem crossing and triplet exciton formation is more effective. The photovoltaic characteristics of same blends are also studied and discussed by comparing the decrease in the overall power conversion efficiency of solar cells.