Comparative analysis of natural and conventional working fluids for use in transcritical Rankine cycle using low‐temperature geothermal source

Theoretical analyses of natural and conventional working fluids‐based transcritical Rankine power cycles driven by low‐temperature geothermal sources have been carried out with the methodology of pinch point analysis using computer models. The regenerator has been introduced and analyzed with a modified methodology considering the considerable variation of specific heat with temperature near the critical state. The evaluations of transcritical Rankine cycles have been performed based on equal thermodynamic mean heat rejection temperature and optimized gas heater pressures at various geothermal source temperature levels ranging from 80 to 120°C. The performances of CO₂, a natural working fluid most commonly used in a transcritical power cycle, have been indicated as baselines. The results obtained show: optimum thermodynamic mean heat injection temperatures of transcritical Rankine cycles are distributed in the range of 60 to 70% of given geothermal source temperature level; optimum gas heater pressures of working fluids considered are lower than baselines; thermal efficiencies and expansion ratios (Exp_r) are higher than baselines while net power output, volume flow rate at turbine inlet (V₁) and heat transfer capacity curves are distributed at both sides of baselines. From thermodynamic and techno‐economic point of view, R125 presents the best performances. It shows 10% higher net power output, 3% lower V₁, 1.0 time higher Exp_r, and 22% reduction of total heat transfer areas compared with baselines given geothermal source temperature of 90°C. With the geothermal source temperature above 100°C, R32 and R143a also show better performances. R170 shows nearly the same performances with baselines except for the higher V₁ value. It also shows that better temperature gliding match between fluids in the gas heater can lead to more net power output. Copyright © 2010 John Wiley & Sons, Ltd.     

低温地热发电有机朗肯循环的优化

采用(火用)分析方法及PR状态方程,建立了低温地热发电有机朗肯循环的工质优选及主要参数优化热力学方法.比较计算了以10种干流体有机工质为循环工质的低温地热发电有机朗肯循环的输出功率、(火用)效率及其余主要热力性能.结果表明,低温地热发电有机朗肯循环的性能极大地受工质的物性及蒸发温度的影响.总体来看,随着工质临界温度的升...     

Thermodynamic analysis and performance optimization of organic rankine cycles for the conversion of low‐to‐moderate grade geothermal heat

The present study considers a thermodynamic analysis and performance optimization of geothermal power cycles. The proposed binary‐cycles operate with moderately low temperature and liquid‐dominated geothermal resources in the range of 110°C to 160°C, and cooling air at ambient conditions of 25°C and 101.3 kPa reference temperature and atmospheric pressure, respectively. A thermodynamic optimization process and an irreversibility analysis were performed to maximize the power output while minimizing the overall exergy destruction and improving the First‐law and Second‐law efficiencies of the cycle. Maximum net power output was observed to increase exponentially with the geothermal resource temperature to yield 16–49 kW per unit mass flow rate of the geothermal fluid for the non‐regenerative organic Rankine cycles (ORCs), as compared with 8–34 kW for the regenerative cycles. The cycle First‐law efficiency was determined in the range of 8–15% for the investigated geothermal binary power cycles. Maximum Second‐law efficiency of approximately 56% was achieved by the ORC with an internal heat exchanger. In addition, a performance analysis of selected pure organic fluids such as R123, R152a, isobutane and n‐pentane, with boiling points in the range of ?24°C to 36°C, was conducted under saturation temperature and subcritical pressure operating conditions of the turbine. Organic fluids with higher boiling point temperature, such as n‐pentane, were recommended for non‐regenerative cycles. The regenerative ORCs, however, require organic fluids with lower vapour specific heat capacity (i.e. isobutane) for an optimal operation of the binary‐cycle. Copyright © 2015 John Wiley & Sons, Ltd.     

Thermodynamic and exergo-economic assessments of a new geothermally driven multigeneration plant

In this paper, a new geothermal-based multigeneration system is designed and investigated in both thermodynamic and economic analyses. The reason to select the geothermal source is that geothermal power is a renewable and sustainable power resource, and also it is not weather dependent. The proposed geothermal-based multigeneration plant is able to produce power, heating, cooling, swimming pool heating, and hydrogen. The main idea in this renewable-based multigeneration system is to create valuable products by using waste heat of subsystems. Then, by applying thermodynamic analyses, the energy and exergy performances of proposed multigeneration system are computed. Also, parametric work has been performed in order to see the impacts of the reference temperature, geothermal fluid temperature, and geothermal water mass flow rate. Finally, exergo-economic analysis based on exergy destruction or thermodynamic losses is done to gain more information about the system and to evaluate it better. According to the calculations, the overall plant's energy and exergy performances are 32.28% and 25.39%. Economic analysis indicates that hydrogen production cost can be dropped down to 1.06 $/kg H₂.     

Design and optimization of a downhole coaxial heat exchanger for an enhanced geothermal system (EGS)

The present study considers the design, performance analysis and optimization of a downhole coaxial heat exchanger for an enhanced geothermal system (EGS). The optimum mass flow rate of the geothermal fluid for minimum pumping power and maximum extracted heat energy was determined. In addition, the coaxial pipes of the downhole heat exchanger were sized based on the optimum geothermal mass flow rate and steady-state operation. Transient effect or time-dependent cooling of the Earth underground, and the optimum amount and size of perforations at the inner pipe entrance region to regulate the flow of the geothermal fluid were disregarded to simplify the analysis. The paper consists of an analytical and numerical thermodynamic optimization of a downhole coaxial heat exchanger used to extract the maximum possible energy from the Earth's deep underground (2 km and deeper below the surface) for direct usage, and subject to a nearly linear increase in geothermal gradient with depth. The thermodynamic optimization process and entropy generation minimization (EGM) analysis were performed to minimize heat transfer and fluid friction irreversibilities. An optimum diameter ratio of the coaxial pipes for minimum pressure drop in both limits of the fully turbulent and laminar fully-developed flow regime was determined and observed to be nearly the same irrespective of the flow regime. Furthermore, an optimum geothermal mass flow rate and an optimum geometry of the downhole coaxial heat exchanger were determined for maximum net power output. Conducting an energetic and exergetic analysis to evaluate the performance of binary power cycle, higher Earth's temperature gradient and lower geofluid rejection temperatures were observed to yield maximum first- and second-law efficiencies.     

Exergetic analysis of various types of geothermal power plants

Based on available surveys, it has been shown that Iran has substantial geothermal potential in the north and north-western provinces, where in some places the temperature reaches 240 °C. In order to better exploit these renewable resources, it is necessary to study this area. Thus, the aim of this paper is a comparative study of the different geothermal power plant concepts, based on the exergy analysis for high-temperature geothermal resources. The considered cycles for this study are a binary geothermal power plant using a simple organic Rankine cycle (ORC), a binary geothermal power plant using an ORC with an internal heat exchanger (IHE), a binary cycle with a regenerative ORC, a binary cycle with a regenerative ORC with an IHE, a single-flash geothermal power plant, a double-flash geothermal power plant and a combined flash-binary power plant. With respect to each cycle, a thermodynamic model had to be developed. Model validation was undertaken using available data from the literature. Based on the exergy analysis, a comparative study was done to clarify the best cycle configuration. The performance of each cycle has been discussed in terms of the second-law efficiency, exergy destruction rate, and first-law efficiency. Comparisons between the different geothermal power plant concepts as well as many approaches to define efficiencies have been presented. The maximum first-law efficiency was found to be related to the ORC with an IHE with R123 as the working fluid and was calculated to be 7.65%. In contrast, the first-law efficiency based on the energy input into the ORC revealed that the binary cycle with the regenerative ORC with an IHE and R123 as the working fluid has the highest efficiency (15.35%). Also, the maximum first-law efficiency was shown to be given by the flash-binary with R123 as the working fluid and was calculated to be 11.81%.     

Analysis of output power smoothing method of the solar chimney power generating system

Severe fluctuation of the output power is a common problem in the generating systems of various renewable energies. The concept of output power fluctuation factor of renewable energy power generating systems was put forward in this paper. Aiming to decrease the fluctuation factor of output power in solar chimney power generating systems (SC), a novel hybrid energy storage system made of water, and sandstone was employed to replace the traditional sandstone energy storage system. The mathematical models of fluid flow, heat transfer and power generating features of SC were established and the influences of material, depth, areas and location of the energy storage layer upon output power were analyzed. The simulation results indicated that adopting the hybrid energy storage of water and sandstone can effectively decrease the fluctuation factor of SC output power and hence smooth the SC output power. In addition, according to the largest daily power generating capability or the smallest peak fluctuation factor, the corresponding optimum depth of the water energy storage layer would be 5 cm or 20 cm, respectively. Copyright © 2012 John Wiley & Sons, Ltd.     

Modelling of organic Rankine cycle system and heat exchanger components

Numerical models of a standard organic Rankine cycle (ORC) system and the heat exchangers comprising the system are developed as a design tool platform for a flexible design. The objective is design of an efficient, cost-effective ORC power plant that can effectively exploit low-grade industrial waste heat or low to medium-temperature geothermal fluid. Typical heat exchanger configurations were modelled, including the circular finned-tube evaporator, air-cooled condenser, and flat-plate preheater. A published ORC configuration and process conditions from experiments are used for the thermodynamic cycle analysis in order to validate of the system model. Heat transfer correlations and friction factors are described for the modelling of the heat exchangers. The simulation results of the ORC system provide the design requirements for the heat exchangers. Geometric specifications and performance of the heat exchangers are determined by iterative simulations.     

Geothermal‐based hydrogen production using thermochemical and hybrid cycles: A review and analysis

Geothermal‐based hydrogen production, which basically uses geothermal energy for hydrogen production, appears to be an environmentally conscious and sustainable option for the countries with abundant geothermal energy resources. In this study, four potential methods are identified and proposed for geothermal‐based hydrogen production, namely: (i) direct production of hydrogen from the geothermal steam, (ii) through conventional water electrolysis using the electricity generated through geothermal power plant, (iii) by using both geothermal heat and electricity for high temperature steam electrolysis and/or hybrid processes, and (iv) by using the heat available from geothermal resource in thermochemical processes. Nowadays, most researches are focused on high‐temperature electrolysis and thermochemical processes. Here we essentially discuss some potential low‐temperature thermochemical and hybrid cycles for geothermal‐based hydrogen production, due to their wider practicality, and examine them as a sustainable option for hydrogen production using geothermal heat. We also assess their thermodynamic performance through energy and exergy efficiencies. The results show that these cycles have good potential and attractive overall system efficiencies over 50% based on a complete reaction approach. The copper‐chlorine cycle is identified as a highly promising cycle for geothermal‐hydrogen production. Copyright © 2009 John Wiley & Sons, Ltd.     

Buoyancy organic Rankine cycle

In the scope of renewable energy, we draw attention to a little known technique to harness solar and geothermal energy. The design here proposed and analyzed is a conceptual hybrid of several patents. By means of a modified organic Rankine cycle, energy is obtained utilizing buoyancy force of a working fluid. Based on thermodynamic properties we propose and compare the performance of Pentane and Dichloromethane as working fluids. Theoretical efficiencies up to 0.26 are estimated for a 51 m (Pentane) and 71.5 m (Dichloromethane) high column of water in a regime below 100 °C operation temperature. These findings are especially relevant in the scope of distributed energy systems, combined cycle plants, and low-temperature Rankine cycles.     

Geothermal energy utilization trends from a technological paradigm perspective

The use of geothermal energy and its associated technologies has been increasing worldwide. However, there has been little paradigmatic research conducted in this area. This paper proposes a systematic methodology to research the development trends for the sustainable development of geothermal energy. A novel data analysis system was created to research the geothermal energy utilization trends, and a technological paradigm theory was adopted to explain the technological changes. A diffusion velocity model was used to simulate and forecast the geothermal power generation development in the diffusion phase. Simulation results showed that the development of installed capacity for geothermal generation had a strong inertia force along with the S-curve. Power generation from geothermal power sources reached a peak in 2008 and is estimated to be saturated by 2030. Geothermal energy technologies in hybrid power systems based on other renewable energy sources look to be more promising in the future.     

Low‐grade heat‐driven Rankine cycle,a feasibility study

Conversion of low‐grade heat to high‐quality energy such as electricity using the Rankine cycle poses serious challenges. When such conversion is possible, it is invariably expensive or unacceptable due to environmental concerns associated with the working medium. The low‐grade heat can either be from exhaust systems or from solar radiation. Thus, the topic addresses a very useful subject, combining energy efficiency and renewable energy. Although high‐grade heat recovery and energy conversion is a mature technology widely covered by the literature, low‐grade energy conversion, especially using thermodynamic cycles, has not been sufficiently addressed to date. This paper addresses the feasibility of a low‐grade heat‐driven Rankine cycle to produce power using a scroll expander, a low toxicity, low flammability, and ozone‐neutral working fluid. A cost benefit analysis of the recommended system shows that it is a viable option for solar power generation, at about one‐third the cost of a comparable photovoltaic system. Copyright © 2008 John Wiley & Sons, Ltd.     

Energy performance and numerical optimization of a screw expander–based solar thermal electricity system in a wide range of fluctuating operating conditions

This paper provides fundamental principles to study the thermodynamic performance of a new screw expander–based solar thermal electricity plant. While steam turbines are generally used in direct steam generation solar systems without admitting fluid in two-phase conditions, steam screw expanders, as volumetric machines, can convert thermal to mechanical energy also by expanding liquid-steam mixtures without a decline in efficiency. In effect, steam turbines are not as competitive as screw expanders when the net power is smaller than 2 MW and for low-grade heat sources. The solar electricity generation system proposed in this paper is based on the steam Rankine cycle: Water is used as both working fluid and storage, parabolic trough collectors are used as a thermal source, and screw expanders are used as power machines. Since screw expanders can operate at off-design working conditions in several situations when installed in direct steam generation solar plants, studying expander performance under fluctuating working situations is a crucial issue. The main aim of the present paper is to establish a thermodynamic model to study the energetic benefits of the proposed power system when off-design operating conditions and variable solar radiation occur. This entails, first and foremost, developing overexpansion and underexpansion numerical models to describe the polytropic expansion phase, which considers all the losses affecting performance of the screw expander under real operating conditions. To assess the best operating conditions and maximum efficiency of the whole power system at part-load working conditions under fluctuating solar radiations, parametric optimization is then improved in a wide range of variable working conditions, assuming condensation pressures of water increasing from 0.1 to 1 bar, under an evaporation temperature rising from 170°C to 300°C.     

Design Sensitivity Analysis of a Plate-Finned Air-Cooled Condenser for Low-Temperature Organic Rankine Cycles

ABSTRACT

Due to increasing world energy demand and environmental concerns, sustainable energy production has become crucial. Among sustainable energy sources such as solar, wind, and geothermal, industrial waste heat (heat normally released to the environment) has a big potential. Organic Rankine cycles (ORCs) are promising systems for utilizing low-temperature (100–250°C) waste heat. For an ORC system, the condenser is a key component. An accurate condenser design is important for cycle efficiency and system cost. In the literature, there are in-tube condensation correlations that are used to design condensers. However, they are not necessarily valid for low-temperature ORC conditions and working fluids, and that might lead to inaccurate end designs. This study comprises a summarized literature survey about in-tube condensation correlations. Then an iterative heat exchanger design methodology is proposed that allows performing a design sensitivity analysis on a V-shaped condenser within an input range of geometric parameters and boundary conditions. Nineteen correlations are implemented to calculate rating parameters like pressure drops, total transferred heat, overall heat transfer coefficient, size, cost and degree of subcooling. The deviations at these parameters are represented as the coefficient of variation that indicates the design condition regions where the prediction methods differ or not.     

Current status of ground source heat pumps in Korea

In Korea, ground source heat pumps (GSHP) have been gaining popularity for space heating and cooling. Because there are few sources of high-temperature geothermal energy in the country, public baths (25–40 °C) and geothermal heat pumps (～15 °C) using low-temperature groundwater or ground are the most dominant direct geothermal uses. The Promotion Law of the New and Renewable Energy Development, Use and Dissemination, enacted in 2004, imposed an obligatory installation of space heating and cooling systems using new and renewable energy sources including geothermal energy for newly constructed public buildings (more than 5% of total construction cost). Between 2004 and 2007, ground source heat pump systems occupied about 60% of the total public installation of new and renewable energy equipment. Starting with 35.2 kW of two facilities in 2000, systems with the capacity of over 127.1 MWt have been installed in 551 buildings (facilities) as of August 2008. The vertical closed heat pump system (closed loop) and the groundwater heat pump system (standing column well type; SCW) occupied 65.1% and 29.3%, respectively, among the total GSHP systems installed. The depth of the vertical loops ranged between 65 and 250 m (average 159 m) and the well depth of the SCW system ranged between 150 and 600 m (average 391 m). The number of geothermal energy companies, installing the GSHP systems, that are officially registered in the relevant authority increased from 5 in 2000 to 397 in July 2008. This paper presents details of the current status of ground source heat pumps in Korea.     

Quantification of the European industrial heat demand by branch and temperature level

We present the first comprehensive estimate of the final energy demand for heat in all EU28 member states for the reference year 2012, differentiated by temperature levels, comparing two different approaches. Two different calculation approaches based on different data sets yielded estimates of the total final energy demand for heat in the EU28 of 8150 PJ and 8518 PJ in 2012, respectively. Approach 1 distinguishes between three different process heat (PH) temperature levels and results in final energy demand for heat <100°C: 2077 PJ, 100–400°C: 2214 PJ and >400°C: 3859 PJ. The second approach distinguishes between low temperature space heat and hot water (<100°C: 1161 PJ) and four different PH temperature levels with a resulting energy demand of <100°C: 1027 PJ, 100–500°C: 1785 PJ, 500–1000°C: 1679 PJ and >1000°C: 2865 PJ. The high share of high‐temperature heat illustrates the limits to the potential decarbonisation of industrial thermal processes with renewable energy sources such as (non‐concentrating) solar thermal, geothermal or environmental heat. Therefore specific information on required temperature levels is of the essence. This, in turn, points out the relevance of renewable electricity and synthetic fuels based on renewable power for a significant reduction of CO₂ emissions from the industry sector in Europe. Considering current data quality, it is recommended to develop a consistent, comprehensive methodology to significantly improve the data basis on industrial heat demand. Copyright © 2015 John Wiley & Sons, Ltd.     

Geothermal energy in Turkey: the sustainable future

Turkey is an energy importing nation with more than half of our energy requirements met by imported fuels. Air pollution is becoming a significant environmental concern in the country. In this regard, geothermal energy and other renewable energy sources are becoming attractive solution for clean and sustainable energy future for Turkey. Turkey is the seventh richest country in the world in geothermal energy potential. The main uses of geothermal energy are space heating and domestic hot water supply, greenhouse heating, industrial processes, heat pumps and electricity generation. The district heating system applications started with large-scale, city-based geothermal district heating systems in Turkey, whereas the geothermal district heating centre and distribution networks have been designed according to the geothermal district heating system (GDHS) parameters. This constitutes an important advantage of GDHS investments in the country in terms of the technical and economical aspects. In Turkey, approximately 61,000 residences are currently heated by geothermal fluids. A total of 665 MW_t is utilized for space heating of residential, public and private property, and 565,000 m² of greenhouses. The proven geothermal heat capacity, according to data from existing geothermal wells and natural discharges, is 3132 MWt. Present applications have shown that geothermal energy is clean and much cheaper compared to the other fossil and renewable energy sources for Turkey.     

Thermodynamic and economic assessments and multi-criteria optimization of a novel poly-generation plant using geothermal energy and multi heat recovery technique

Smart use of clean energy sources for achieving higher performance and designing cost-effective systems is recognized as an essential solution for reducing fossil fuel consumption. In this regard, this study supports a comprehensive evaluation and multi-criteria optimization of a novel poly-generation plant embracing geothermal energy from thermodynamic and thermoeconomic perspectives. Hence, the utilization of modified subsystems and smart use of multi heat recovery processes are projected and appraised. In this regard, the plant consists of a double-flash binary geothermal subsystem, an organic Rankine cycle in combination with an ejector refrigeration cycle considering a zeotropic working fluid (a mixture of pentane and R142b), a heating production heat exchanger, and a proton exchange membrane electrolyzer with the combined production of cooling, heating, power, and hydrogen. The crucial thermodynamic and thermoeconomic variables are investigated against key parameters and concluded that the sensitivity of outcomes is more evident with the variation in zeotropic working fluid composition and the vapor quality at the heating production heat exchanger's outlet. The attained results at the optimum mode demonstrated, the energy and exergy efficiencies of the plant as well as total unit costs of products are as being 44.5%, 35.8%, and 18.8 $/GJ, respectively.     

Study on Heat Transfer in Heat Exchangers for a New Supercritical Organic Rankine Cycle

Electrical power from geothermal heat is hardly efficient, if the temperature level of geothermal water is low. This situation is predominant in middle Europe, for example, in Germany, where even in hot-spot areas like Norddeutsches Becken, Oberrheingraben, and Molassebecken the temperature of geothermal water is less than 160°C. For this, efforts have to be made in optimizing the power cycle efficiency. Supercritical fluids provide a higher net energy output per unit mass than subcritical fluids but their physical properties strongly depend on temperature variations, especially close to the supercritical point. Based on the requirements of a new modular and mobile supercritical power cycle MONICA (modular low temperature power cycle Karlsruhe), which will be built within the next few years, different heat exchanger types are investigated within this study in order to determine the most compact design with respect to mobility, mountability, and efficiency. Changes in physical properties of propane, the working fluid of the new cycle, are taken into account by iterative, stepwise calculation of heat exchanger types like double-pipe, shell-and-tube, and plate heat exchangers. For this, common Nusselt number correlations are implemented in the stepwise iteration. Influence of geometry on flow conditions and analysis of part load sensitivity are provided.