Malted and unmalted oats in brewing

Using oats as a raw material in brewing has recently become the focus of increased interest. This is due to research findings that have shown that oats can be consumed safely by coeliac sufferers. It is also a response to consumer demand for products with novel sensory properties. In this study, beer was produced entirely from oat malt, from barley malt and from oat and barley malts mixed with various quantities of unmalted oats. Compared with barley wort, wort made from malted oats provided a lower extract content and had a higher protein content, but a lower free amino nitrogen content (FAN). The oat wort also showed increased viscosity and haze. The addition of unmalted oats during wort production produced significant changes in the physico‐chemical parameters of both oat and barley worts and beers. Unmalted oats caused an increase in wort viscosity and haze, and a reduction in total soluble nitrogen and FAN. Unmalted oats also contributed to lowering the concentration of higher alcohols and esters. Beer made from 100% oat and barley malts exhibited a similar alcohol content. The use of an oat adjunct in both cases resulted in a lower ethanol content. The introduction of enzyme preparations during the production of wort with oat adjunct had many benefits: increased extract content and FAN; a higher volume of wort; and a lower viscosity that led to faster wort filtration. This research suggests that the use of enzymes is necessary to make production using a high proportion of oats in the grist profitable. Copyright © 2014 The Institute of Brewing & Distilling     

ROLE OF ALPHA-GLUCOSIDASE IN THE FERMENTABLE SUGAR COMPOSITION OF SORGHUM MALT MASHES*

The cause of the high glucose to maltose ratio in sorghum malt worts was studied. Mashing temperature and pH strongly affected both the amount of glucose and the proportion of glucose relative to total fermentable sugars. The relative proportion of glucose was higher when mashing was performed. at pH 4.0, close to the pH optimum for sorghum alpha-glucosidase, than at the natural pH of the mash (pH 6.0–5.5). Mashing according to the EBC procedure using an enzymic malt extract with pre-cooked malt insoluble solids producing a wort containing maltose and glucose in an approximately 4:1 ratio, whereas mashing with a malt extract without pre-cooking the malt insoluble solids resulted in a wort with approximately equal amounts of maltose and glucose. Both treatments gave the same quantity of total fermentable sugars and amount of wort extract. Sorghum alpha-glucosidase was confirmed to be highly insoluble in water. All or virtually all activity was associated with the insoluble solids. Hence, it appears that the high amount of glucose formed when sorghum malt is mashed conventionally is due to alpha-glucosidase activity. Pre-cooking the malt insoluble solids inactivates the alpha-glucosidase, preventing the hydrolysis of maltose to glucose.     

Effect of varying starch properties and mashing conditions on wort sugar profiles

The aim of this research was to investigate the relationship between starch composition in barley and its malted counterpart alongside malt enzyme activity and determine how these factors contribute to the fermentable sugar profile of wort. Two Australian malting barley varieties, Commander and Gairdner, were sourced from eight growing locations alongside a commercial sample of each. For barley and malt, total starch and gelatinisation temperature were taken, and for malt, α‐ and β‐amylase activities were measured. Samples were mashed using two mashing profiles (infusion and Congress) and the subsequent wort sugar composition and other quality measures (colour, original gravity, soluble nitrogen) were tested. Variety had no significant (<0.05) effect on any barley, malt, enzyme or wort characteristics. However, growing location impacted gelatinisation temperature, colour, malt protein content and original gravity. The gelatinisation temperature in malt samples was higher, by ~0.8°C, than in the equivalent barley sample. Several malt samples, even with protein contents <12.0%, had gelatinisation temperature >65°C. The fermentable sugars measured in the malt prior to mashing showed a higher proportion of maltose than glucose or maltotriose. In addition, there were significant differences in the amount of sugar produced by each mashing method with the high temperature infusion producing a higher amount of sugar and proportionally more maltose. There is scope for further research on the effect of genetics and growing environment on gelatinisation temperature, mash performance and fermentable sugar development. Routinely measuring gelatinisation temperature and providing this information on malt specification sheets could help brewers optimise performance. © 2019 The Institute of Brewing & Distilling     

α-GLUCOSIDASE ACTIVITY OF SORGHUM AND BARLEY MALTS

Sorghum malt α-glucosidase activity was highest at pH 3.75 while that of barley malt was highest at pH 4.6. At pH 5.4 employed in mashing sorghum malt α-glucosidase was more active than the corresponding enzyme of barley malt. α-Glucosidase was partly extracted in water but was readily extracted when L-cysteine was included in the extraction buffer, pH 8. Sorghum malt made at 30°C had higher α-glucosidase activities than the corresponding malts made at 20°C and 25°C. Nevertheless, the sorghum malts made at 20°C and 25°C produced worts which contained more glucose than worts of malt made at 30°C. Although barley malts contained more α-glucosidase activity than sorghum malts, the worts of barley had the lowest levels of glucose. The limitation to maltose production in sorghum worts, produced at 65°C, is due to inadequate gelatinization of starch and not to limitation to β-amylase and α-amylase activities. Gelatinization of the starch granules of sorghum malt in the decantation mashing procedure resulted in the production of sorghum worts which contained high levels of maltose, especially when sorghum malt was produced at 30°C. Although the β-amylase and α-amylase levels of barley malt was significantly higher than those of sorghum malted optimally at 30°C, sorghum worts contained higher levels of glucose and equivalent levels of maltose to those of barley malt. It would appear that the individual activities of α-glucosidase, α-amylase and β-amylase of sorghum malts or barley malts do not correlate with the sugar profile of the corresponding worts. In consequence, specifications for enzymes such as α-amylase and β-amylase in malt is best set at a range of values rather than as single values.     

Comparison of the impact on the performance of small‐scale mashing with different proportions of unmalted barley,Ondea Pro®, malt and rice

The impact of using different combinations of unmalted barley, Ondea Pro® and barley malt in conjunction with a 35% rice adjunct on mashing performance was examined in a series of small scale mashing trials. The objective was to identify the potential optimal levels and boundaries for the mashing combinations of barley, Ondea Pro®, malt and 35% rice (BOMR) that might apply in commercial brewing. Barley and malt samples used for the trials were selected from a range of Australian commercial barley and malt samples following evaluation by small‐scale mashing. This investigation builds on previous studies in order to adapt the technology to brewing styles common in Asia, where the use of high levels of rice adjunct is common. Mashing with the rice adjunct, combined with differing proportions of barley, Ondea Pro® and malt, resulted in higher extract levels than were observed for reference mashing, using either 100% malt reference or 100% barley reference and Ondea Pro® enzymes. Synergistic mashing effects between barley, Ondea Pro® and malt were observed for mash quality and efficiency parameters, particularly wort fermentability. The optimum levels of barley in the grist (with the relative level of Ondea Pro®) were assessed to be in the range 45–55% when paired with 10–20% malt and 35% rice. When the proportion of malt was reduced below 10% of the grist, substantial reductions in wort quality were observed for wort quality parameters including extract, lautering, fermentability, free amino nitrogen and haze. Extension of this new approach to brewing with rice adjuncts will benefit from further research into barley varietal selection in order to better meet brewer's quality requirements for the finished beer. Copyright © 2016 The Institute of Brewing & Distilling     

Effect of unmalted oats (Avena sativa L.) on the quality of high-gravity mashes and worts without or with exogenous enzyme addition

Barley malt is the preferred brewing material these days because of its high extract content and high enzyme activities. However, when substituting malted barley with oats to create a unique beer flavor and aroma, endogenous malt enzymes become the limiting factor. Therefore, the objectives of this study were to evaluate the effect of 10–40 % unmalted oats on the quality of high-gravity mashes/worts and to investigate the limitations of endogenous malt enzymes as well as the benefits of the application of industrial enzymes. The enzyme mix Ondea^® Pro was found to be particularly suitable for mashing with unmalted oats and was therefore used in the present rheological tests and laboratory-scale mashing trials. In order to gain detailed information about the biochemical processes occurring during mashing, the quality of mashes was comprehensively analyzed after each mash rest using standard methods described by Mitteleuropäische Brautechnische Analysenkommission and Lab-on-a-Chip capillary electrophoresis. Mashing with up to 40 % oats resulted in increased mash consistencies, color/pH (20 °C) values, β-glucan concentrations, wort viscosities 12.0 %, and filtration times as well as decreased FAN and extract contents. The application of Ondea^® Pro enormously increased the color of worts despite lower pH values but considerably improved the quality and processability of 30 or 40 % oat-containing mashes/worts. However, the substitution of up to 20 % barley malt with unmalted oats can easily be realized without the addition of exogenous enzymes.     

Corn grist adjunct – application and influence on the brewing process and beer quality

In the brewing industry, barley malt is often partially replaced with adjuncts (unmalted barley, wheat, rice, sorghum and corn in different forms). It is crucial, however, to preserve constant quality in the beer to meet the expectations of consumers. In this work, how the addition of corn grist (10 and 20%) influences the quality of wort and beer was examined. The following parameters were analysed: wort colour, dimethyl sulphide (DMS) and protein content, non‐fermentable extract, extract drop during fermentation, alcohol content and the attenuation level of the beer, together with filtration performance. The samples (all‐malt, and adjunct at 10 and 20% corn grist) were industrial worts and the beers produced in a commercial brewery (3000 hL fermentation tanks). The application of 10 and 20% corn grist had an effect on the wort colour, making it slightly lighter (11.1 and 10.5°EBC, respectively) than the reference barley malt wort (12.2°EBC). The free amino nitrogen level, DMS and non‐fermentable extract were significantly lower in the worts produced with the adjunct; the alcohol content and attenuation levels were higher in the beers produced with adjunct. The use of corn grist, at the level of up to 20% of total load, appears to affect some of the technological aspects of wort and beer production, but it does not significantly influence the final product characteristics. Copyright © 2014 The Institute of Brewing & Distilling     

Effect of Amyloglucosidase on Wort Composition and Fermentable Carbohydrate Depletion in Sorghum Lager Beers

A three‐factorial experiment with a level of confidence of P < 0.05 was performed to study fermentable carbohydrate depletion and ethanol production during 144 h fermentations of lager beers produced with barley malt (BM), sorghum malt (SM), refined maize (MZ) or waxy sorghum (WXSOR) grits treated during mashing with or without amyloglucosidase (AMG). The percentage glucose, maltose and maltotriose, based on total fermentable carbohydrates for the BM wort was 20, 68 and 13% and for the SM wort 35, 48 and 17% respectively. Treatment with AMG increased wort glucose from 9.3 to 24.5 g/L wort and total fermentable sugar equivalents, expressed as g glucose/L, from 59.2 to 72.6 g/L wort. The SM worts had approximately 50% more glucose and 40% less initial maltose content respectively compared to the BM worts. The WXSOR grits produced worts and beers with similar properties to those produced from the MZ adjuncts. AMG addition led to a >2.5 fold increment in wort glucose and 23% in total fermentable carbohydrate content. Linear regression analysis determined that the consumption rate of fermentable carbohydrates during fermentation followed first order reaction kinetics. Depletion times to reach 50% of the initial concentrations of glucose, maltose and maltotriose were 49, 128 and 125 h, respectively, clearly indicating that the fermenting yeast preferred glucose. Maltose and maltotriose depletion times of the AMG treated worts were significantly faster and lower, respectively, when compared with the untreated worts. At the end of the fermentation, the BM beers contained higher ethanol levels (5.1% v/v) than the SM beers (3.9% v/v). For AMG treated beers, no significant differences in ethanol content were observed among samples mashed with BM and beers produced from SM and MZ grits. The results demonstrated that AMG could be used to increase the initial concentration of glucose and total fermentable carbohydrates thus decreasing dextrin levels, especially from sorghum mashes.     

THE PROPERTIES,COMPOSITION AND FERMENTABILITIES OF WORTS MADE FROM 100% RAW SORGHUM AND COMMERCIAL ENZYMES

A mashing regime was developed using 100% raw sorghum which enabled commercially acceptable hot water extracts to be obtained in 85 minutes with minimal use of a heat stable α-amylase and proteolytic enzymes. This gave worts of HWE 295 1°/kg, with FAN levels of about 40 mg/l and ammonium ion concentration of about 60 mg/l. Higher, but commercially unacceptable, levels of proteolytic enzymes gave worts with FAN from 84.5 to 95 (mg/l). Addition of an amyloglucosidase as the commercial preparation Amylo300L, was required to convert the HWE to fermentable extract. The addition of Amylo300L, increased the DP1, DP2 and DP3 carbohydrate fractions of the worts from 22% to more than 90% of the total, compared to about 80% for a wort made from malted barley without the use of enzymes. Two different proteolytic enzymes gave different extracts and FAN contents presumably reflecting either differences in susceptibilities of the sorghum to the two enzymes or the presence of different additional enzyme activities in the different preparations. The level of ammonium ions in malted barley worts was 86 mg/l and up to 88 mg/l in worts produced from sorghum and enzymes. Enzyme addition produced increased levels of ammonia. The content of Group A (the most readily assimilated) amino acids was proportionally higher in sorghum worts compared to malted barley wort. Worts made from raw sorghum and enzymes, containing as little as 40 mg/l FAN, were fully attenuated. The yeast consumed about 35 mg/l FAN and 45 mg/l ammonium ions. Under identical fermentation conditions, the same yeast, fermenting a malted barley wort of comparable extract consumed 104 mg/l FAN and 37 mg/l ammonium ions.     

Variation in maltose in sweet wort from barley malt and rice adjuncts with differences in amylose structure

Starch from malt and solid adjuncts provides the majority of fermentable sugars for fermentation. However, there is no current data on the variation in starch structure (particularly long chained amylose) and its impact on the final wort composition of fermentable sugars, specifically maltose. This is the first study to report variation in amylose structure from barley malt and rice used as an adjunct and how this impacts the production of maltose. We compared four commercial malts with two rice adjuncts mashes, in solid and liquid additions, with an all‐malt mash used as a control. All combinations of malt and rice adjuncts were tested under two grist‐to‐liquor (G:L) ratios (1:3 and 1:4) in a 65°C ramped mash. After mashing, the wort original gravity and maltose concentration were measured. The commercial malts had different malt quality but very similar gelatinisation temperatures (~65°C). The malts varied in starch and amylose contents but had only minor variations in average amylose chain lengths. The two rice adjuncts also had similar average amylose chains lengths, but quite different amylose contents, and hence different gelatinisation temperatures. The results showed that liquid adjunct mashes had higher original gravity and maltose concentration for both G:L ratios. However, there was no consistent result in original gravity or maltose between G:L ratio or adjunct type, suggesting interactions between each malt and rice adjunct. Knowing amylose chain length could improve understanding of the potential maltose levels of the sweet wort prior to fermentation. © 2018 The Institute of Brewing & Distilling     

Quality Assessment of a Sorghum Variety Malted Commercially under Tropical Conditions and Controlled Tropical Temperatures in the Laboratory

A sorghum variety was supplied as commercial malt and as an unmalted cereal by a maltster. The commercial sample had been malted in a tropical country. Sub‐samples of the unmalted cereal were malted in the laboratory under controlled germination temperatures of 28°C and 30°C. Laboratory and commercially malted sorghum were studied for their brewing qualities. The α‐amylase development in sorghum malt was enhanced when germination was carried out at the higher temperature of 30°C rather than at 28°C. Hot water extract (HWE) was more variable. With infusion mashing, results showed a significant difference for germination time (3–6 days), but no significant difference relating to germination temperature. With the decantation mashing method the reverse was observed. The low numerical values of HWE obtained from sorghum malt in the infusion mashing process confirmed that this process is not suitable to produce optimal extract development from malted sorghum. The 28°C germinated sorghum released more FAN products into the worts than the 30°C malt, using both the infusion and decantation methods. With regard to the parameters tested, commercially malted sorghum gave lower analytical values than laboratory malted sorghum. It was also observed that variations in malting temperatures and mashing processes can cause unexpected variations in the analyses of sorghum malt. These findings suggest that careful process control is required during the malting and mashing of sorghum.     

FERMENTATION OF WORTS MADE FROM 100% RAW SORGHUM AND ENZYMES

Worts made from raw sorghum and enzymes were successfully fermented even though the level of FAN present (51 mg/l) is well below that essential for fermentation of wort made from malted barley. Changes in typical fermentation parameters such as specific gravity, pH uptake of free amino nitrogen (FAN) and ammonium ions mirrored the increase in yeast cell concentration. Yeast viability remained high throughout the fermentation. Under identical fermentation conditions, malted barley worts showed typical fermentation profiles. However, malted barley worts with specific gravity maintained by the addition of D-glucose, but in which the FAN was diluted to a level similar to that found in a wort made from sorghum and enzymes, fermented more slowly and failed to attenuate fully. Five consecutive fermentations, using yeast cropped from the preceding to pitch the current fermentation were conducted. The specific gravity profiles were essentially the same in all five fermentations. Final values of pH, yeast in suspension, yeast viability and FAN were also indistinguishable. The yeast crop taken from fermentations of worts made from raw sorghum and enzymes represented a 5-fold increase over the initial pitching rate. When compared to commercial beers, the beers derived from fermentation of worts made from raw sorghum and enzymes contained lower levels of ethyl acetate, and higher levels of both 2- and 3-methyl butanol. In the beers derived from sorghum, isobutanol was always less than 20% of the total higher alcohol concentration.     

Application of Unconventional Raw Materials and Procedures in Wort Production*

This paper deals with investigations of wort production by the application of unmalted raw material — native barley as a partial substitute for malt in grist. This adjunct was differently treated: (1) thermal decomposition, (2) enzymic decomposition by the addition of commercial enzyme “Termamyl”, and (3) hydrothermic decomposition i.e. extruding. Native barley prepared by these methods was added in proportions up to 70% of the grist, without the addition of exogenous enzymes. Experiments were carried out on a laboratory scale by using an infusion mashing procedure for wort production. The results obtained indicated that the application of native barley as the adjunct, gelatinised by heat treatment gave good results up to 10% as malt substitute. Larger amounts of barley gelatinised by heat treatment decreased extract yields. Malt substitution with pretreatment of barley with enzyme did not produce satisfactory results. Worts had reduced levels of extract and soluble nitrogen, which were insufficient for the production of high quality beer. Application of barley flakes in quantities up to 50% produced wort which had good analytical quality parameters.     

Influence of High Protein Digestibility Sorghums on Free Amino Nitrogen (FAN) Production during Malting and Mashing

In sorghum brewing, obtaining sufficient Free Amino Nitrogen (FAN) for rapid and complete fermentation remains a problem due to the high proportions of unmalted sorghum used and the poor digestibility of wet‐heat treated sorghum protein. Sorghum mutant lines with high protein digestibility have been developed through breeding. These high protein digestibility sorghums (HPDS) have protein bodies with villi‐like borders that apparently facilitate protease access. This work investigated FAN production from HPDS when malted and mashed, to assess their potential for use in sorghum brewing to improve wort FAN levels. When malted, HPDS contained substantially higher levels of FAN than normal protein digestibility sorghums (NPDS), 32 mg/100 g malt more. However, when the HPDS were mashed either as malt, or as grain or malt plus exogenous proteases, FAN production during mashing was not substantially higher than with NPDS subjected to the same treatments, only 6, 6–18 and 9–13 mg/100 g grain or malt, respectively. This is probably due to wet‐heat induced cross‐linking of the kafirin proteins reducing their susceptibility to proteolysis. Notwithstanding this, HPDS could be very useful for improving FAN levels in sorghum brewing if they are malted.     

Application of Biological Acidification to Improve the Quality and Processability of Wort Produced from 50% Raw Barley

In this study four strains of lactic acid bacteria (LAB) were chosen to bioacidify a mash containing 50% barley and 50% malt. The strains were isolated from malted and unmalted barley and assayed for extracellular enzymatic activities (proteases, amylases, β‐glucanases). The biologically acidified mash was compared to a chemically acidified mash, 100% malt mash un‐acidified and 50% malt and 50% barley mash unacidified. Characteristics such as pH, extract, colour, viscosity, total soluble nitrogen (TSN), free amino nitrogen (FAN), apparent fermentability, β‐glucan and lautering performance of the resultant worts were determined. A model lautering system replicating one used in a brewery was designed and built in University College Cork (UCC) to measure the lautering performance of the bioacidified mashes. The new system was compared to the filtration method used in EBC method 4.5.1. Overall the addition of LAB to bioacidify a mash of 50% barley and 50% malt resulted in faster filtration times, which correlated with decreased β‐glucan levels. Proteolytic LAB had a positive influence on the quality of wort and resulted in increased FAN levels. Lighter colour worts were observed along with increased extract levels.     

Changes in Sorghum Malt During Storage

The diastatic power of the freshly kilned sorghum malt at 68.1°WK had a 29% drop after six months of storage. Freshly kilned sorghum malt displayed high wort turbidity (4.9 EBC) which dropped to 0.95 EBC and 1 EBC after 2 and 6 months of storage respectively. The colour of the malt worts faded slightly over the trial period from 7.6 EBC in freshly kilned malt to 6.8 EBC after six months. Extract remained fairly steady throughout the study period most likely due to the use of external amylolytic enzymes during mashing. The protein in extract/protein in grain fluctuated between 46.6% in the freshly kilned malt to 43.2% at the end of six months. The apparent extract after final attenuation (AEFA) indicates more fermentability beginning from two months after storage. Free α‐amino nitrogen (FAN) dropped from 238 mg/L to 194 mg/L after six months of storage. Mash filtration with a micro‐mash filter remained prolonged (86–93 min) throughout the six months of storage.     

Mashing Studies with Unmalted Sorghum and Malted Barley

The effects on wort quality when mashing with unmalted sorghum (0–100%) and malted barley (100–0%) in combination with industrial enzymes were evaluated. A mashing program with temperature stands at 50°C, 95°C and 60°C was used. Different combinations of commercial enzymes were evaluated. A heat stable α‐amylase was found to be essential for efficient saccharification. The inclusion of a fungal α‐amylase in mashes with a high sorghum content improved filtration rates to that of 100% malted barley mashes. Addition of a bacterial protease increased the amount of nitrogen solubilisation and peptide degradation. An increase of the relative proportion of sorghum in the grist resulted in decreases in wort filtration, colour, viscosity, attenuation limit, free amino nitrogen, high molecular weight nitrogen, and a corresponding increase in pH (p < 0.01). Overall the addition of malted barley in small proportions to unmalted sorghum mashes together with commercial enzymes was found to improve the potential for brewing a high quality lager beer from unmalted sorghum.     

ENZYME AND ACID HYDROLYSIS OF MALTED MILLET (Pennisetum typhoidees) AND SORGHUM (Sorghum bicolor)

Malted millet and sorghum were hydrolysed by the enzymes produced during malting. Malted and unmalted millet and sorghum were acid hydrolysed. The enzyme hydrolysed carbohydrate was mostly glucose, with only traces of disaccharides, in the case of malted millet. The yield of enzyme hydrolysed carbohydrate was however low in both millet and sorghum. Acid hydrolysis of malted millet or sorghum showed that glucose of malted grains was destroyed during acid hydrolysis more than pentoses in the malted grains.     

DEVELOPMENT OF A MASHING PROFILE FOR THE USE OF MICROBIAL ENZYMES IN BREWING WITH RAW SORGHUM (80%) AND MALTED BARLEY OR SORGHUM MALT (20%)

Different time and temperature programmes were used to evaluate the production of hot water extract (HWE) and free amino nitrogen (FAN) from mashes containing raw sorghum and either malted sorghum or malted barley in the presence of microbial enzymes. Two malted varieties of sorghum (SK 5912 and Zaria) were used. The former gave higher HWE but lower FAN than the latter. Sorghum malts were unable to provide enzyme activity for starch extraction and exogenous enzymes were always needed. Seventeen commercially available enzyme preparations were assessed. A double-mash process was developed. Inclusion of calcium ions (200 ppm) was beneficial but adjustment of mash pH had little effect. Raw sorghum was gelatinised at 100°C for 30–40 min in the presence of a heat-stable α-amylase followed by mixing with a malt mash (started at B0°C) to give a temperature of 65°C with a total mash time of 167 min (127 min from mixing the mashes). The inclusion of a single commercial enzyme preparation (containing both proteolytic and amylolytic activities) was sufficient to achieve satisfactory HWE and FAN. Addition of different activities or combinations of activities gave no significant advantages. To obtain levels of FAN of 100–140 mg/l however excessive amounts of enzymes were required.     

Effect of wheat malt on the concentration of metal ions in wort and brewhouse by‐products

The ionic composition of brewer's wort depends on the raw materials and processing employed. The macroelement content is usually sufficient for yeast, but some of the microelements (mainly zinc) often need to be supplemented to the wort. Wheat malt is used as an adjunct in the production of beer, replacing up to 60% of barley malt. In this study, the effect of replacing barley malt with wheat malt on the concentration of magnesium, manganese, iron and zinc ions in brewer's wort was investigated. The ionic content of both the raw materials and by‐products were analysed. Similar amounts of magnesium ions were found in wheat malt and barley malt, whereas, manganese, zinc and iron were more abundant in the wheat malt. Nevertheless, wheat malt did not cause a significant change in ion concentration in the first wort (except for magnesium; its content decreased). The ionic content in the spent grains increased owing to wheat malt addition; the concentration of ions in the wort decreased after wort boiling (Mn²⁺ and Fe) or remained unaffected (Mg²⁺ and Zn²⁺). It was concluded that the ionic composition of the wort depends mainly on the removal rate of ions from the wort during mash filtration and hot trub separation, rather than on the actual amount of ions in the raw materials. Copyright © 2015 The Institute of Brewing & Distilling