Fate of oestrogens during anaerobic blackwater treatment with micro-aerobic post-treatment.

The fate of oestrone (E1), 17beta-oestradiol (E2) and 17alpha-ethynyloestradiol (EE2) was investigated in a concentrated blackwater treatment system consisting of an UASB septic tank, with micro-aerobic post-treatment. In UASB septic tank effluent a (natural) total concentration of 4.02 microg/L E1 and 18.69 microg/L E2, comprising the sum of conjugated (>70% for E1 and >80% for E2) and unconjugated forms, was measured. During post-treatment the unconjugated oestrogens were removed to below 1 microg/L. A percentage of 77% of the measured unconjugated E1 and 82% of E2 was associated with particles >1.2 microm in the final effluent implying high sorption affinity of both compounds. When spiking the UASB septic tank effluent with E1, E2, EE2 and the sulphate conjugate of E2, removal in the micro-aerobic post-treatment was >99% for both E2 and EE2 and 83% for E1. The lower removal value for E1 was a result of (slow) deconjugation during the treatment, and in the final effluent still 40% of E1 and 99% of E2 was present in conjugated form. The latter was the result of incomplete deconjugation of the spiked E2(3S) in the post-treatment system.     

Removal of endocrine disrupting chemicals in a large scale membrane bioreactor plant combined with anaerobic-anoxic-oxic process for municipal wastewater reclamation

The removal of eight typical endocrine disrupting compounds (EDCs) in a full scale membrane bioreactor combined with anaerobic-anoxic-oxic process (A(2)/O-MBR) for municipal wastewater reclamation located in Beijing was investigated. These EDCs, including 4-octylphenol (4-OP), 4-n-nonylphenol (4-n-NP), bisphenol A (BPA), estrone (E1), 17α-estradiol (17α-E2), 17β-estradiol (17β-E2), estriol (E3) and 17α-ethinylestradiol (EE2), were simultaneously analyzed by gas chromatography/mass spectrometry after derivatization. The concentrations of eight EDCs were also measured in sludge of anaerobic, anoxic, oxic and membrane tanks to measure sludge-water distribution coefficients (K(d) values) as the indicator of adsorption propensity of target compound to sludge. The removal efficiencies of EDCs reached above 97%, except for 4-n-NP removal efficiency of 72%, 4-OP removal efficiency of 75% and EE2 removal efficiency of 87% in the A(2)/O-MBR process. The high K(d) values indicated that the sludge had a large adsorption capacity for these EDCs, and significantly contributed to removal of EDCs. Yeast estrogen screen assay was performed on samples to assess the total estrogenic activity by measuring the 17β-E2 equivalent quantity (EEQ), expressed in ng-EEQ/L. The measured EEQ value was markedly reduced from 72.1 ng-EEQ/L in the influent to 4.9 ng-EEQ/L in the effluent. Anoxic tank and anaerobic tank contributed to 80% and 37% in total EEQ removal, respectively.     

Enhanced primary treatment of concentrated black water and kitchen residues within DESAR concept using two types of anaerobic digesters.

Anaerobic digestion of concentrated domestic wastewater streams--black or brown water, and solid fraction of kitchen waste is considered as a core technology in a source separation based sanitation concept (DESAR--decentralised sanitation and reuse). A simple anaerobic digester can be implemented for an enhanced primary treatment or, in some situations, as a main treatment. Two reactor configurations were extensively studied; accumulation system (AC) and UASB septic tank at 15, 20 and 25 degrees C. Due to long retention times in an AC reactor, far stabilisation of treated medium can be accomplished with methanisation up to 60%. The AC systems are the most suitable to apply when the volume of waste to be treated is minimal and when a direct reuse of a treated medium in agriculture is possible. Digested effluent contains both liquid and solids. In a UASB septic tank, efficient separation of solids and liquid is accomplished. The total COD removal was above 80% at 25 degrees C. The effluent contains COD and nutrients, mainly in a soluble form. The frequency of excess sludge removal is low and sludge is well stabilised due to a long accumulation time.     

Analysis and occurrence of estrogen in wastewater in Japan.

This paper describes an analytical procedure for free estrogens and their conjugates in domestic wastewater. The procedure demonstrated in this study is innovative in terms of levels of detection and quantification of the following substances: estrone (E1); 17beta-estradiol (E2); 17alpha-ethynylestradiol (EE2); estriol (E3); estrone-3-sulfate (E1-S); beta-estradiol 3-sulfate (E2-S); estriol 3-sulfate (E3-S); estrone beta-D-glucuronide (E1-G); beta-estradiol 17-(beta-D)-glucuronide (E2-G); estriol 3-(beta-D)-glucuronide (E3-G); beta-estradiol 3-sulfate 17-glucuronide (E2-SandG); and estradiol 3,17-disulfate (E2-diS). The detection limits of this method ranged from 0.1 to 1.4 ng/l. The recovery efficiencies of the estrogens in the analysis from influent and effluent of the secondary settling tank in a wastewater treatment plant (WWTP) were higher than 94% for the free estrogens, but were less than 50% for the conjugated estrogens. The field study using this method was conducted at twenty WWTPs in Japan. The median concentrations of the estrogens ranged from ND to as high as >100 ng/l. In the influent and secondary effluent samples, the concentrations of E1, E2 and E3 were the same levels as those previously reported. We found that the conjugated estrogens exist at higher concentrations in the influent and the secondary effluent than in the other studies, and that the concentrations of the conjugated estrogens were higher than those of the free estrogens.     

Energy saving system with high effluent quality for municipal sewage treatment by UASB-DHS

An up-flow anaerobic sludge blanket (UASB) - down-flow hanging sponge (DHS) was applied to Japanese municipal sewage treatment, and its treatability, energy consumption, and sludge production were evaluated. The designed sewage load was 50 m(3)/d. The sewage typically had a chemical oxygen demand (COD) of 402 mg/L, a suspended solids (SS) content of 167 mg/L, and a temperature of 17-29 °C. The UASB and DHS exhibited theoretical hydraulic retention times of 9.7 and 2.5 h, respectively. The entire system was operated without temperature control. Operation was started with mesophilic anaerobic digested sludge for the UASB and various sponge media for the DHS. Continuous operational data suggest that although the cellulose decomposition and methanogenic process in the UASB are temperature sensitive, stable operation can be obtained by maintaining a satisfactory sludge volume index and sludge concentration. For the DHS, the cube-type medium G3-2 offers superior filling rates, biological preservation and operational execution. The SS derived from the DHS contaminated the effluent but could be removed by optional sand filtration. A comparison with conventional activated sludge (CAS) treatment confirmed that this system is adequate for municipal sewage treatment, with an estimated energy requirement and excess sludge production approximately 75 and 85% less than those of CAS, respectively.     

Anaerobic bioprocessing of sewage sludge, focusing on degradation of linear alkylbenzene sulfonates (LAS).

Anaerobic degradation of sludge amended with linear alkylbenzene sulfonates (LAS) was tested in a one stage continuous stirred tank reactor (CSTR) and a two stage reactor system consisting of a CSTR as first step and upflow anaerobic sludge bed (UASB) reactor as the second step. Anaerobic removal of LAS was only observed at the second step but not at the first step. Removal of LAS in the UASB reactors was approx. 80% where half was due to absorption and the other half was apparently due to biological removal as shown from the LAS mass balance. At the end of the experiment the reactors were spiked with 14C-LAS which resulted in 5.6% 14CO2 in the produced gas. Total mass balance of the radioactivity was however not achieved. In batch experiments it was found that LAS at concentrations higher than 50 mg/l is inhibitory for most microbial groups of the anaerobic process. Therefore, low initial LAS concentration is a prerequisite for successful LAS degradation. The results from the present study suggest that anaerobic degradation of LAS is possible in UASB reactors when the concentration of LAS is low enough to avoid inhibition of microorganisms active in the anaerobic process.     

Characteristics of estrogen decomposition by ozonation.

Since the natural estrogens 17 beta-estradiol (E2) and estron (E1), and the synthetic estrogen 17 alpha-ethynyl estradiol (EE2) have strong endocrine disrupting effects and the tendency to persist in effluent from wastewater treatment plants, effective measures are needed to remove them from wastewater. In this research, to gain an understanding of the characteristics of estrogen decomposition by ozonation, experiments were conducted using effluent from an actual wastewater treatment plant. In this experiment, estrogen was added to effluent at a concentration of 200 ng/l and 20 ng/l before the ozonation experiments. The results showed 90% or more of estrogen concentration and estrogenic activity of E2, El and EE2 to be removed at an ozone dose of 1 mg/l. At an ozone dose of 3 mg/l, the estrogen concentration and estrogenic activity of E2, El and EE2 in the treated water fell below the detection limit. The removal rate was not influenced by the kind of estrogen. No generation of byproducts with estrogenic activity was observed. The authors conclude that estrogen in secondary treated wastewater can be almost entirely removed at the practical ozone dose rate applied for the purpose of disinfection, which is up to about 5 mg/l.     

A mechanistic model for fate and removal of estrogens in biological nutrient removal activated sludge systems

Two estrogen fate and transformation models were integrated with a comprehensive activated sludge model (ASM) to predict estrogen removal based on biomass and solids production. Model predictions were evaluated against published full-scale plant data as well as results from a laboratory-scale sequencing batch reactor (SBR) fed synthetic wastewater. The estrogen fate model relating the rate of total estrogen degradation to soluble estrogen concentrations successfully predicted estrogen removals when compared with measured concentrations. Model fit 17α-ethinylestradiol (EE2) biodegradation rate constant was 19 to 43% of the estrone (E1) value and 31 to 72% of the 17β-estradiol (E2) value.     

Calculation methods to perform mass balance of endocrine disrupting compounds in a submerged membrane bioreactor: fate and distribution of estrogens during the biological treatment

The purpose of this paper is to report the study of the fate and distribution of three endocrine disrupting compounds (estrogens); Estrone (E1), 17β-estradiol (E2), and 17α-ethinylestradiol (EE2) in a laboratory scale submerged membrane bioreactor (SMBR). For this matter, both aqueous and solids phases were analyzed for the presence of E1, E2 and EE2. The outcome of this study was that three SMBRs showed enhanced elimination of estrogens in different operational conditions; the estrogen removal was close to 100% in SMBR. Additionally, E1, E2 and EE2 were detected in SMBR sludge at concentrations of up to 41.2, 37.3 and 36.9 ng g(-1) dry weight, respectively. The estrogen removal in the SMBRs was directly influenced by a combination of simultaneous biodegradation-adsorption processes, indicating that the main removal mechanism of the estrogens in the SMBRs is the biodegradation process. The E1, E2 and EE2 were biologically degraded in the SMBR (87-100%). The sorption of estrogens onto activated sludge was from 2%. Therefore, a high potential for estrogen removal by biodegradation in the SMBR was observed, allowing less estrogen concentration in the dissolved phase available for the adsorption of these compounds onto biological flocs. Two different methods were carried out for mass balance calculations of estrogens in SMBR. For the first method, the measured data was used in both liquid and solid phases, whereas for the second one, it was in aqueous phase and solid-water distribution coefficients (K(d)) value of E1, E2 and EE2. The purpose of these methodologies is to make easier the identification of the main mechanisms involved in the removal of E1, E2 and EE2 in a SMBR. Both methods can be applied in order to determine the mechanism, fate and distribution of estrogens in a SMBR.     

Anaerobic treatment of Hong Kong leachate followed by chemical oxidation.

Landfill leachate of Hong Kong was first treated by the upflow anaerobic sludge blanket (UASB) process. At 37 degrees C, pH 7.1-8.5 and a HRT of 5.1-6.6 days, the process removed 66-90% of COD in the leachate for loading rates of 1-2.4 g-COD/l day depending on the strength of landfill leachate. The final effluent contained 1440-1910 mg-COD/l and 70-91 mg-BOD/l. About 92.5% of the total COD removed was converted to methane and the rest was converted to biomass with an average net growth yield of 0.053 g-VSS/g-COD-removed. The granules developed in the UASB reactor were 0.5-1.5 mm in size and exhibited good settleability. The UASB effluent was then further polished by two oxidation processes. The UASB-ozonation process removed 93.0% of the 12900 mg/l of COD from the raw leachate. The UASB-Fenton-ozonation process improved the COD removal efficiency to 99.3%. The final effluent had only 85 mg/l of COD and 10 mg/l of BOD5. Ozonation was most effectively conducted at pH 7-8 with the addition of 300 mg/l of H2O2 and for the duration of 30 min. Ozonation also significantly improved the biodegradability of the organic residues. Nearly 50% of these residues could be used as carbon source in denitrification.     

UASB与ABR工艺处理印染废水中试实验研究

对上流式厌氧反应器(UASB)和折流式厌氧反应器(ABR)处理难降解印染废水进行中试研究。结果表明:在厌氧反应器最佳水力停留时间为24 h条件下,UASB和ABR稳定运行2个多月,在进水COD质量浓度波动较大的情况下(ρmax=1 020.0 mg/L,ρmin=593.6 mg/L,ρ均=755.4 mg/L),UASB和ABR出水平均COD质量浓度分别为409.3 mg/L和420.9 mg/L,平均去除率分别为45.5%和43.9%。两种厌氧反应器对色度去除效果较佳,进水平均色度342倍,出水平均色度分别78倍和80倍,平均去除率分别为77.2%和76.6%。印染废水B/C由0.29分别提高到0.46和0.43,废水可生化性明显改善,UASB较ABR效果好。     

Grey water treatment in upflow anaerobic sludge blanket (UASB) reactor at different temperatures

The treatment of grey water in two upflow anaerobic sludge blanket (UASB) reactors, operated at different hydraulic retention times (HRTs) and temperatures, was investigated. The first reactor (UASB-A) was operated at ambient temperature (14-25 degrees C) and HRT of 20, 12 and 8 h, while the second reactor (UASB-30) was operated at controlled temperature of 30 degrees C and HRT of 16, 10 and 6 h. The two reactors were fed with grey water from 'Flintenbreite' settlement in Luebeck, Germany. When the grey water was treated in the UASB reactor at 30 degrees C, total chemical oxygen demand (CODt) removal of 52-64% was achieved at HRT between 6 and 16 h, while at lower temperature lower removal (31-41%) was obtained at HRT between 8 and 20 h. Total nitrogen and phosphorous removal in the UASB reactors were limited (22-36 and 10-24%, respectively) at all operational conditions. The results showed that at increasing temperature or decreasing HRT of the reactors, maximum specific methanogenic activity of the sludge in the reactors improved. As the UASB reactor showed a significantly higher COD removal (31-64%) than the septic tank (11-14%) even at low temperature, it is recommended to use UASB reactor instead of septic tank (the most common system) for grey water pre-treatment. Based on the achieved results and due to high peak flow factor, a HRT between 8 and 12 h can be considered the suitable HRT for the UASB reactor treating grey water at temperature 20-30 degrees C, while a HRT of 12-24 h can be applied at temperature lower than 20 degrees C.     

Upgrading of Florence wastewater treatment plant: co-digestion and nitrogen autotrophic removal.

In recent years a completely autotrophic nitrogen removal process based on Anammox biomass has been tested in a few European countries in order to treat anaerobic supernatant and to increase the COD/N ratio in municipal wastewater. This work reports experimental results on a possible technical solution to upgrade the S. Colombano treatment plant which treats wastewater from the Florentine urban area. The idea is to use 50% of the volume of the anaerobic digester in order to treat external sewage sludge (as septic tank sludge) together with waste activated sludge and to treat the resulting effluent on a SHARON-ANAMMOX process in order to remove nitrogen from the anaerobic supernatant. Anaerobic co-digestion, tested in a 200 L pilot plant, enables low cost treatment of septic tank sludge and increases biogas production; however, it also increases the nitrogen load re-circulated to the WWTP, where nitrogen removal efficiency is already low (<50%), due to the low COD/N ratio, which limits predenitrification efficiency. Experimental results from a SHARON process tested in a lab-scale pilot plant show that nitrite oxidising bacteria are washed-out and steady nitrite production can be achieved at retention times in the range 1 - 1.5 days, at 35 degrees C. In a lab-scale SBR reactor, coupled with a nitration bioreactor, maximum specific nitrogen removal rate under nitrite-limiting conditions (with doubling time equal to about 26 days at 35 degrees C) was equal to 0.22 kgN/kgSSV/d, about 44 times the rate measured in inoculum Anammox sludge. Finally, a cost analysis of the proposed upgrade is reported.     

Advanced treatment by anaerobic process followed by aerobic membrane bioreactor for effluent reuse in paper mill industry.

The operation of an activated sludge process at a paper mill (AIPM) in Hedera, Israel, was often characterized by disturbances. As part of a research and development project, a study on new biological treatment was initiated. The study included the operation of three pilot units: a. anaerobic treatment by upflow anaerobic sludge blanket (UASB); b. aerobic treatment by two pilot units including activated sludge and membrane bioreactor (MBR), which have been operated in parallel for comparison reasons. The pilot plant working on anaerobic treatment performed COD reduction from 2,365 to 755 mg/L, expressed as average values. Based on the pilot study, a full scale anaerobic treatment system has been erected. During a period of 100 days, after achieving steady state, the MBR system provided steady operation performance, while the activated sludge produced effluent characterized by oscillatory qualities. The following results, based on average values, indicate much lower suspended solids concentrations in the MBR effluent, 2.5 mg/L, as compared to 25 mg/L in the activated sludge. The ability to develop and maintain a concentration of over 11,000 mg/L of mixed liquor volatile suspended solids in the MBR enabled an intensive bioprocess at relatively high cell residence time. This study demonstrates that the anaerobic process, followed by aerobic MBR can provide effluent of high quality which can be considered for economic reuse in the paper mill industry.     

EGSB反应器的启动运行研究

采用两个小试规模的EGSB(ExpandedGranularSludgeBed)反应器 ,分别接种厌氧絮状污泥和颗粒污泥来研究其启动规律。试验结果表明 ,接种厌氧絮状污泥的R1反应器 ,由于出水循环的采用导致严重的污泥流失 ,首先应按UASB反应器的运行方式培养出颗粒污泥后 ,再按EGSB反应器方式运行 ,共需 78d才能完成启动 ;接种厌氧颗粒污泥的R2反应器 ,采用适宜的回流比有利于细菌的生长和反应器运行效果的改善 ,在经过短暂的无回流驯化后 ,即可按EGSB运行方式启动运行 ,仅需 32d即完成启动。     

Pretreatment of silk-dyeing industrial wastewater by UASB reactor.

The objective of this study was to investigate the performance of the upflow anaerobic sludge blanket (UASB) reactor as the pretreatment system for silk-dyeing wastewater. Two laboratory-scale UASB reactors, with working volume of 15.59 I, were used during May 1998 to June 1999. The actual wastewater was diluted to reduce ammonium ion toxicity on anaerobic bacteria. The experiments were conducted at the organic loading rates (OLRs) of 0.52, 1.01, 1.04, 1.54 and 2.56 kgCOD/(m3 x d), treating only wastewater generated from the acid-dye process of mixed-species raw silk. It took approximately 4 1/2 months to reach the steady-state conditions. It was found that the COD removal was in the ranges of 74.1-85.3%, except at OLR 2.56 kgCOD/(m3 x d) where efficiency significantly dropped to 55.2%. The apparent color removal was in the similar trend as COD. During the study periods, wastewater input had various color shades while the effluent generally looked pale yellowish. The methane generation rates ranged from 0.18-0.31 m3/kg COD removed, with methane composition 81.0-88.1% in biogas. The average granule size in the sludge bed had slowly increased to 0.73 mm in the last experiment. It can be concluded that the UASB reactor is suitable as a pretreatment system for silk-dyeing wastewater. An OLR of 1 kgCOD/(m3 x d) and an influent concentration diluted to 2,600 mgCOD/l are suggested while COD and apparent color removal efficiency of 80% and 70%, respectively, can be expected.     

Factors affecting the activity of anammox bacteria during start up in the continuous culture reactor.

Factors affecting cultivation of extremely slow-growing bacteria (anaerobic ammonium oxidiser, doubling time 11 days) were investigated by using upflow anaerobic sludge blanket (UASB) reactors which can maintain high solid retention time. The effects of concentrations of DO, free ammonia (FA), and nitrite on activation of anammox activity were tested during the start-up period. The reactor was inoculated with granular sludge collected from a full-scale UASB reactor used for treating brewery wastewater, and sludge from a piggery wastewater treatment plant and rotating biological contactor treating sewage. Results of continuous operation showed that concentrations of DO, free ammonia (FA) and nitrite in the reactors played a key role in stimulating the anammox activity during start-up period. It is crucial to keep DO below 0.2 ppm, FA below 2 mg/L and nitrite nitrogen below 35 mg/L to cultivate anammox cells in the continuous bioreactor. When the levels of DO, FA and nitrite in the influent were controlled at less than the inhibition levels, the anammox activity increased gradually in the anaerobic condition. Addition of hydrogen sulphide into the reactor enhanced anammox activity in the continuous culture. Through the SEM, TEM and FISH analysis, anammox bacteria were detected in the granular sludge after 3 months of continuous operation.     

Alkaline and acid hydrolytic processes in aerobic and anaerobic sludges: effect on total EPS and fractions.

Sludge samples from an upflow anaerobic sludge blanket (UASB) reactor and four submerged aerated biofilters (BFs) of a wastewater treatment plant (1,000 inhab.) were processed at bench scale by alkaline and acid hydrolysis with the objective to evaluate the organic matter solubilization, volatile solids (VS) destruction and the effect of hydrolytic processes on the extracellular polymeric substances (EPS) fraction of the sludge samples. The results showed that alkaline hydrolysis of sludge samples treatment with 1.0% total solids (TS) using NaOH 20 meq L(-1) was more efficient on organic matter solubilization and VS destruction than acid hydrolysis. The EPS sludge content was also affected by the alkaline treatment of anaerobic sludge samples. The EPS concentrations (mg EPS/gVSS) on the anaerobic sludge after the alkaline treatment were significantly lowered according to sample height in the UASB reactor. Data indicated that the EPS sludge fraction is the main component affected by the alkaline hydrolytic process of anaerobic sludge samples.     

Fate of oestrogenic compounds and identification of oestrogenicity in a wastewater treatment process.

Understanding of the fate of oestrogen and oestrogenic compounds is important in improving the removal efficiency for oestrogens in wastewater treatment plants (WWTPs). In this study an attempt was made to clarify the fate of oestrogen, oestrogen sulphates, and oestrogenic compounds (synthetic oestrogen, nonylphenol and its relatives) by an instrumental analysis, and the fate of oestrogenicity by an in vitro assay. The investigation was conducted in an activated sludge WWTP in winter and summer, focusing on identification of the primary substances that induce oestrogenicity. Wastewater samples were analysed by employing the silica-gel fractionation technique in conjunction with two-step column chromatography. The results revealed that, in winter, the WWTP efficiencies for the removal of nitrogen and oestrogens decreased and the oestrone level increased with the progress of the treatment. Oestrone and oestrogenic substances are likely to circulate between the aeration tank and the final sedimentation tank. In summer, however, these compounds were effectively removed in the WWTP. The results of the column chromatography coupled with the bioassay suggested that E1 and E2 are the predominant contributors to the oestrogenicity in the influent, return sludge and effluent of the WWTP. The measurement by the instrumental analysis supported these findings.     

Start-up and steady-state results of a full-scale UASB reactor treating malting wastewater.

An Imhoff tank was reconstructed into a 250 m3 UASB reactor in order to treat a malting plant wastewater. The UASB was inoculated with sludge from an anaerobic lagoon used for slaughterhouse wastewater treatment. After two months of operation the reactor achieved full load with an HRT of 17 h, a COD removal higher than 80% and a biogas production of 300 m3/day (77% average methane content), with an organic loading rate of 3.6 kgCOD/m3.d (0.24 kgCOD/kgVSS.d). A yield coefficient of 0.09 gVSS/gCODrem was found from a mass balance. The fat present in the inoculated sludge (48 mg/gSSV) did not affect the start up performance. Sludge from the inoculum with high content of fat (270 mg/gSSV), was separated by flotation in the first week of operation. The COD removal efficiency was scarcely influenced by the reactor operation temperature (17-25 degrees C).