High-Performance $hbox{In}_{0.7}hbox{Ga}_{0.3}hbox{As}$ -Channel MOSFETs With High-$kappa$ Gate Dielectrics and $alpha$-Si Passivation

Long and short buried-channel $hbox{In}_{0.7}hbox{Ga}_{0.3}hbox{As}$ MOSFETs with and without $alpha$-Si passivation are demonstrated. Devices with $alpha$-Si passivation show much higher transconductance and an effective peak mobility of 3810 $hbox{cm}^{2}/ hbox{V} cdot hbox{s}$. Short-channel MOSFETs with a gate length of 160 nm display a current of 825 $muhbox{A}/muhbox{m}$ at $V_{g} - V_{t} = hbox{1.6} hbox{V}$ and peak transconductance of 715 $muhbox{S}/muhbox{m}$. In addition, the virtual source velocity extracted from the short-channel devices is 1.4–1.7 times higher than that of Si MOSFETs. These results indicate that the high-performance $hbox{In}_{0.7}hbox{Ga}_{0.3} hbox{As}$-channel MOSFETs passivated by an $alpha$ -Si layer are promising candidates for advanced post-Si CMOS applications.      

A Comparative NBTI Study of $hbox{HfO}_{2}$, $hbox{HfSiO}_{x}$, and SiON p-MOSFETs Using UF-OTF $I_{rm DLIN}$ Technique

The time, temperature, and oxide-field dependence of negative-bias temperature instability is studied in $hbox{HfO}_{2}/hbox{TiN}$, $ hbox{HfSiO}_{x}/hbox{TiN}$, and SiON/poly-Si p-MOSFETs using ultrafast on-the-fly $I_{rm DLIN}$ technique capable of providing measured degradation from very short (approximately microseconds) to long stress time. Similar to rapid thermal nitrided oxide (RTNO) SiON, $hbox{HfO}_{2}$ devices show very high temperature-independent degradation at short (submilliseconds) stress time, not observed for plasma nitrided oxide (PNO) SiON and $hbox{HfSiO}_{x}$ devices. $hbox{HfSiO}_{x}$ shows lower overall degradation, higher long-time power-law exponent, field acceleration, and temperature activation as compared to $hbox{HfO}_{2}$, which are similar to the differences between PNO and RTNO SiON devices, respectively. The difference between $ hbox{HfSiO}_{x}$ and $hbox{HfO}_{2}$ can be attributed to differences in N density in the $hbox{SiO}_{2}$ IL of these devices.      

Impacts of $hbox{N}_{2}$ and $hbox{NH}_{3}$ Plasma Surface Treatments on High-Performance LTPS-TFT With High-$kappa$ Gate Dielectric

Low-temperature polycrystalline-silicon thin-film transistors (LTPS-TFTs) with high- $kappa$ gate dielectrics and plasma surface treatments are demonstrated for the first time. Significant field-effect mobility $mu_{rm FE}$ improvements of $sim$86.0% and 112.5% are observed for LTPS-TFTs with $hbox{HfO}_{2}$ gate dielectric after $hbox{N}_{2}$ and $ hbox{NH}_{3}$ plasma surface treatments, respectively. In addition, the $hbox{N}_{2}$ and $ hbox{NH}_{3}$ plasma surface treatments can also reduce surface roughness scattering to enhance the field-effect mobility $mu_{rm FE}$ at high gate bias voltage $V_{G}$, resulting in 217.0% and 219.6% improvements in driving current, respectively. As a result, high-performance LTPS-TFT with low threshold voltage $V_{rm TH} sim hbox{0.33} hbox{V}$, excellent subthreshold swing S.S. $sim$0.156 V/decade, and high field-effect mobility $mu_{rm FE} sim hbox{62.02} hbox{cm}^{2}/hbox{V} cdot hbox{s}$ would be suitable for the application of system-on-panel.      

Extraction of the Effective Mobility of $ hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ MOSFETs

The extraction of the effective mobility on $hbox{In}_{0.53} hbox{Ga}_{0.47}hbox{As}$ metal–oxide–semiconductor field-effect transistors (MOSFETs) is studied and shown to be greater than 3600 $hbox{cm}^{2}/hbox{V} cdot hbox{s}$. The removal of $C_{rm it}$ response in the split $C$–$V$ measurement of these devices is crucial to the accurate analysis of these devices. Low-temperature split $C$–$V$ can be used to freeze out the $D_{rm it}$ response to the ac signal but maintain its effect on the free carrier density through the substrate potential. Simulations that match this low-temperature data can then be “warmed up” to room temperature and an accurate measure of $Q_{rm inv}$ is achieved. These results confirm the fundamental performance advantages of $hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ MOSFETs.      

Scaling Properties of $hbox{Ge}$ –$hbox{Si}_{x}hbox{Ge}_{1 - x}$ Core–Shell Nanowire Field-Effect Transistors

We demonstrate the fabrication of high-performance $hbox{Ge}$ –$hbox{Si}_{x}hbox{Ge}_{1 - x}$ core–shell nanowire (NW) field-effect transistors with highly doped source (S) and drain (D) and systematically investigate their scaling properties. Highly doped S and D regions are realized by low-energy boron implantation, which enables efficient carrier injection with a contact resistance much lower than the NW resistance. We extract key device parameters, such as intrinsic channel resistance, carrier mobility, effective channel length, and external contact resistance, as well as benchmark the device switching speed and on/off current ratio.      

Comparative Study of the Low-Frequency-Noise Behaviors in a-IGZO Thin-Film Transistors With $hbox{Al}_{2}hbox{O}_{3}$ and $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ Gate Dielectrics

A comparative study is made of the low-frequency noise (LFN) in amorphous indium–gallium–zinc oxide (a-IGZO) thin-film transistors (TFTs) with $hbox{Al}_{2}hbox{O}_{3}$ and $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ gate dielectrics. The LFN is proportional to $hbox{1}/f^{gamma}$, with $gamma sim hbox{1}$ for both devices, but the normalized noise for the $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ device is two to three orders of magnitude lower than that for the $hbox{Al}_{2} hbox{O}_{3}$ device. The mobility fluctuation is the dominant LFN mechanism in both devices, but the noise from the source/drain contacts becomes comparable to the intrinsic channel noise as the gate overdrive voltage increases in $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ devices. The $hbox{SiN}_{x}$ interfacial layer is considered to be very effective in reducing LFN by suppressing the remote phonon scattering from the $hbox{Al}_{2}hbox{O}_{3}$ dielectric. Hooge's parameter is extracted to $sim !!hbox{6.0} times hbox{10}^{-3}$ in $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ devices.      

High-Density and Low-Leakage-Current MIM Capacitor Using Stacked $hbox{TiO}_{2}/hbox{ZrO}_{2}$ Insulators

We have fabricated high-$kappa hbox{Ni}/hbox{TiO}_{2}/hbox{ZrO}_{2}/ hbox{TiN}$ metal–insulator–metal (MIM) capacitors. A low leakage current of $hbox{8} times hbox{10}^{-8} hbox{A/cm}^{2}$ at 125 $^{circ}hbox{C}$ was obtained with a high 38- $hbox{fF}/muhbox{m}^{2}$ capacitance density and better than the $hbox{ZrO}_{2}$ MIM capacitors. The excellent device performance is due to the lower electric field in 9.5-nm-thick $hbox{TiO}_{2}/ hbox{ZrO}_{2}$ devices to decrease the leakage current and to a higher $kappa$ value of 58 for $ hbox{TiO}_{2}$ as compared with that of $hbox{ZrO}_{2}$ to preserve the high capacitance density.      

0.8-V Supply Voltage Deep-Submicrometer Inversion-Mode $hbox{In}_{0.75}hbox{Ga}_{0.25}hbox{As}$ MOSFET

We report the experimental demonstration of deep-submicrometer inversion-mode $hbox{In}_{0.75}hbox{Ga}_{0.25}hbox{As}$ MOSFETs with ALD high- $k$ $hbox{Al}_{2}hbox{O}_{3}$ as gate dielectric. In this letter, n-channel MOSFETs with 100–200-nm-long gates have been fabricated. At a supply voltage of 0.8 V, the fabricated devices with 200–130-nm-long gates exhibit drain currents of 232–440 $muhbox{A}/muhbox{m}$ and transconductances of 538–705 $muhbox{S}/muhbox{m}$. The 100-nm device has a drain current of 801 $muhbox{A}/muhbox{m}$ and a transconductance of 940 $muhbox{S}/muhbox{m}$. However, the device cannot be pinched off due to severe short-channel effect. Important scaling metrics, such as on/off current ratio, subthreshold swing, and drain-induced barrier lowering, are presented, and their relations to the short-channel effect are discussed.      

Electrical Properties of $hbox{Ga}_{2}hbox{O}_{3}/ hbox{GaAs}$ Interfaces and GdGaO Dielectrics in GaAs-Based MOSFETs

Electrical properties of $hbox{Ga}_{2}hbox{O}_{3}/hbox{GaAs}$ interfaces with GdGaO cap dielectrics used in recent enhancement-mode GaAs-based NMOSFETs which perform in line with theoretical model predictions are presented. Capacitors with GdGaO thickness ranging from 3.0 to 18 nm ($hbox{0.9} leq hbox{EOT} leq hbox{3.9} hbox{nm}$) have been characterized by capacitance–voltage measurements. Midgap interface state density $D_{rm it}$, effective workfunction $phi_{m}$, fixed charge $Q_{f}$, dielectric constant $kappa$, and low field leakage current density are $hbox{2} times hbox{10}^{11} hbox{cm}^{-2} cdot hbox{eV}^{-1}$, 4.93 eV, $-hbox{8.9} times hbox{10}^{11} hbox{cm}^{-2}$, 19.5, and $hbox{10}^{-9}{-} hbox{10}^{-8} hbox{A/cm}^{2}$, respectively. The presence of interfacial Gd was confirmed to dramatically degrade electrical interface properties. The data illuminate the intimate interplay between heterostructure and interface engineering to achieve optimum MOSFET operation.      

Nonvolatile-Memory Characteristics of $hbox{AlO}^{-}$ -Implanted $hbox{Al}_{2}hbox{O}_{3}$

The nonvolatile-memory (NVM) characteristics of $hbox{AlO}^{-}$ -implanted $hbox{Al}_{2}hbox{O}_{3}$ structures are reported and shown to exhibit promising behaviors, including fast program/erase speeds and high-temperature data retention. Photoconductivity spectra show the existence of two dominant trap levels, located at around 2 and 4 eV below the conduction band minimum of $hbox{Al}_{2}hbox{O}_{3}$, and our calculations show that these levels are likely attributed to the defects in the $hbox{Al}_{2}hbox{O}_{3}$, such as the Al–O divacancy. The relative concentrations of these defects vary with the implant fluence and are shown to explain the NVM characteristics of the samples irradiated to different fluences.      

Electrical Properties of $hbox{Bi}_{5}hbox{Nb}_{3} hbox{O}_{15}$ Thin Film Grown on $hbox{TiN}/hbox{SiO}_{2}/ hbox{Si}$ at Room Temperature for Metal–Insulator–Metal Capacitors

Buckling was observed in $hbox{Bi}_{5}hbox{Nb}_{3}hbox{O}_{15}$ (BiNbO) films grown on $hbox{TiN}/hbox{SiO}_{2}/hbox{Si}$ at 300 $^{circ}hbox{C}$ but not in films grown at room temperature and annealed at 350 $^{circ}hbox{C}$. The 45-nm-thick films showed a high capacitance density and a low dissipation factor of 8.81 $hbox{fF}/muhbox{m}^{2}$ and 0.97% at 100 kHz, respectively, with a low leakage current density of 3.46 $hbox{nA}/hbox{cm}^{2}$ at 2 V. The quadratic and linear voltage coefficients of capacitance of this film were 846 $hbox{ppm}/hbox{V}^{2}$ and 137 ppm/V, respectively, with a low temperature coefficient of capacitance of 226 $hbox{ppm}/^{circ}hbox{C}$ at 100 kHz. This suggests that a BiNbO film grown on a $hbox{TiN}/ hbox{SiO}_{2}/hbox{Si}$ substrate is a good candidate material for high-performance metal–insulator–metal capacitors.      

Electrical Properties of Amorphous $hbox{Bi}_{5} hbox{Nb}_{3}hbox{O}_{15}$ Thin Film for RF MIM Capacitors

Amorphous $hbox{Bi}_{5}hbox{Nb}_{3}hbox{O}_{15}(hbox{B}_{5} hbox{N}_{3})$ film grown at 300 $^{circ}hbox{C}$ showed a high-$k$ value of 71 at 100 kHz, and similar $k$ value was observed at 0.5–5.0 GHz. The 80-nm-thick film exhibited a high capacitance density of 7.8 fF/$muhbox{m}^{2}$ and a low dissipation factor of 0.95% at 100 kHz with a low leakage-current density of 1.23 nA/ $hbox{cm}^{2}$ at 1 V. The quadratic and linear voltage coefficient of capacitances of the $hbox{B}_{5}hbox{N}_{3}$ film were 438 ppm/$hbox{V}^{2}$ and 456 ppm/V, respectively, with a low temperature coefficient of capacitance of 309 ppm/$^{circ}hbox{C}$ at 100 kHz. These results confirmed the potential of the amorphous $hbox{B}_{5}hbox{N}_{3}$ film as a good candidate material for a high-performance metal–insulator–metal capacitors.      

Low Turn-On Voltage and High-Current $hbox{InP}/ hbox{In}_{0.37}hbox{Ga}_{0.63}hbox{As}_{0.89}hbox{Sb}_{0.11}/hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ Double Heterojunction Bipolar Transistors

We report on the dc and microwave characteristics of an $ hbox{InP/In}_{0.37}hbox{Ga}_{0.63}hbox{As}_{0.89}hbox{Sb}_{0.11}/hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ double heterojunction bipolar transistor grown by solid-source molecular beam epitaxy. The pseudomorphic $hbox{In}_{0.37}hbox{Ga}_{0.63}hbox{As}_{0.89}hbox{Sb}_{0.11}$ base reduces the conduction band offset $Delta E_{C}$ at the emitter/base junction and the base band gap, which leads to a very low $V_{rm BE}$ turn-on voltage of 0.35 V at 1 $hbox{A/cm}^{2}$ . A current gain of 125 and a peak $f_{T}$ of 238 GHz have been obtained on the devices with an emitter size of $hbox{1}times hbox{10} muhbox{m}^{2}$, suggesting that a high collector average velocity and a high current capability are achieved due to the type-II lineup at the InGaAsSb/InGaAs base/collector junction.      

The $hbox{Pd/TiO}_{2}$/ $hbox{n}$-LTPS Thin-Film Schottky Diode on Glass Substrate for Hydrogen Sensing Applications

A $hbox{Pd/TiO}_{2}$/n-type low-temperature-polysilicon (n-LTPS) MOS thin-film Schottky diode fabricated on a glass substrate for hydrogen sensing is reported. The n-LTPS is an excimer-laser-annealed and $hbox{PH}_{3}$ -gas-plasma-treated amorphous-silicon (a-Si) thin film. At room temperature and $-$2-V bias, the developed MOS Schottky diode exhibited a high signal ratio of 1540 to 50 ppm of hydrogen gas, with a fast response time of 40 s, respectively. The signal ratio is better or comparable with that of other reported MOS-type hydrogen gas sensors prepared on Si or III–V compound substrate. In addition, the signal ratio is 7.6, 14, and 30 times over other interfering gases of $ hbox{C}_{2}hbox{H}_{5}hbox{OH}$, $hbox{C}_{2}hbox{H}_{4}$ , and $hbox{NH}_{3}$ at room temperature and a concentration of 8000 ppm at $-$2-V bias, respectively. Thus, the developed MOS Schottky diode shows promise for the future development and commercialization of a low-cost hydrogen sensor.      

High-Performance Poly-Silicon TFTs Using a High-$k$ $hbox{PrTiO}_{3}$ Gate Dielectric

In this letter, a polycrystalline-silicon thin-film transistor (poly-Si TFT) with a high- $k$ $hbox{PrTiO}_{3}$ gate dielectric is proposed for the first time. Compared to TFTs with a $hbox{Pr}_{2}hbox{O}_{3}$ gate dielectric, the electrical characteristics of poly-Si TFTs with a $hbox{PrTiO}_{3}$ gate dielectric can be significantly improved, such as lower threshold voltage, smaller subthreshold swing, higher $I_{rm on}/I_{rm off}$ current ratio, and larger field-effect mobility, even without any hydrogenation treatment. These improvements can be attributed to the high gate capacitance density and low grain-boundary trap state. All of these results suggest that the poly-Si TFT with a high- $k$ $hbox{PrTiO}_{3}$ gate dielectric is a good candidate for high-speed and low-power display driving circuit applications in flat-panel displays.      

Improvement of On–Off-Current Ratio in $ hbox{TiO}_{rm x}$ Active-Channel TFTs Using $hbox{N}_{2} hbox{O}$ Plasma Treatment

Without sacrificing the on-current in the transfer characteristics, we have successfully reduced the off-current part by the optimal $hbox{N}_{2}hbox{O}$ plasma treatment to improve the on–off-current ratio in n-type titanium oxide $( hbox{TiO}_{rm x})$ active-channel thin-film transistors. While the high-power (275 W) $hbox{N}_{2}hbox{O}$ plasma treatment oxidizes the whole $hbox{TiO}_{rm x}$ channel and results in the reduction of both on- and off-current, the optimized low-power (150 W) process makes the selective oxidation of the top portion in the channel and reduces only the off-current significantly. Increase in on–off ratio by almost five orders of magnitude is achieved without change in on-current by using the presented method.      

$hbox{TiN/ZrO}_{2}$/Ti/Al Metal–Insulator–Metal Capacitors With Subnanometer CET Using ALD-Deposited $hbox{ZrO}_{2}$ for DRAM Applications

We provide the first report of the structural and electrical properties of $hbox{TiN/ZrO}_{2}$/Ti/Al metal–insulator–metal capacitor structures, where the $hbox{ZrO}_{2}$ thin film (7–8 nm) is deposited by ALD using the new zirconium precursor ZrD-04, also known as Bis(methylcyclopentadienyl) methoxymethyl. Measured capacitance–voltage ($C$– $V$) and current–voltage ( $I$–$V$) characteristics are reported for premetallization rapid thermal annealing (RTP) in $hbox{N}_{2}$ for 60 s at 400 $^{circ}hbox{C}$, 500 $^{circ}hbox{C}$, or 600 $^{ circ}hbox{C}$. For the RTP at 400 $^{circ}hbox{C}$ , we find very low leakage current densities on the order of nanoamperes per square centimeter at a gate voltage of 1 V and low capacitance equivalent thickness values of $sim$ 0.9 nm at a gate voltage of 0 V. The dielectric constant of $ hbox{ZrO}_{2}$ is 31 $pm$ 2 after RTP treatment at 400 $^{circ}hbox{C}$.      

Low-Voltage Organic Field-Effect Transistor With PMMA/$ hbox{ZrO}_{2}$ Bilayer Dielectric

This paper reports on the application of a bilayer polymethylmethacrylate (PMMA)/ $hbox{ZrO}_{2}$ dielectric in copper phthalocyanine (CuPc) organic field-effect transistors (OFETs). By depositing a PMMA layer on $hbox{ZrO}_{2}$, the leakage of the dielectric is reduced by one order of magnitude compared to single-layer $hbox{ZrO}_{2}$. A high-quality interface is obtained between the organic semiconductor and the combined insulators. By integrating the advantages of polymer and high- $k$ dielectrics, the device achieves both high mobility and low threshold voltage. The typical field-effect mobility, threshold voltage, on/off current ratio, and subthreshold slope of OFETs with bilayer dielectric are $hbox{5.6}timeshbox{10}^{-2} hbox{cm}^{2}/hbox{V} cdot hbox{s}$, 0.8 V, $hbox{1.2} times hbox{10}^{3}$, and 2.1 V/dec, respectively. By using the bilayer dielectrics, the hysteresis observed in the devices with single-layer $hbox{ZrO}_{2}$ is no longer present.      

1580-V–40-$hbox{m}Omegacdot hbox{cm}^{2}$ Double-RESURF MOSFETs on 4H-SiC $(hbox{000}bar{hbox{1}})$

Double-reduced-surface-field (RESURF) MOSFETs with $hbox{N}_{2}hbox{O}$ -grown oxides have been fabricated on the 4H-SiC $(hbox{000} bar{hbox{1}})$ face. The double-RESURF structure is effective in reducing the drift resistance, as well as in increasing the breakdown voltage. In addition, by utilizing the 4H-SiC $(hbox{000}bar{hbox{1}})$ face, the channel mobility can be increased to over 30 $hbox{cm}^{2}/hbox{V}cdothbox{s}$, and hence, the channel resistance is decreased. As a result, the fabricated MOSFETs on 4H-SiC $( hbox{000}bar{hbox{1}})$ have demonstrated a high breakdown voltage $(V_{B})$ of 1580 V and a low on-resistance $(R_{rm ON})$ of 40 $hbox{m}Omega cdothbox{cm}^{2}$. The figure-of-merit $(V_{B}^{2}/R_{rm ON})$ of the fabricated device has reached 62 $hbox{MW/cm}^{2}$, which is the highest value among any lateral MOSFETs and is more than ten times higher than the “Si limit.”      

A Theoretical Comparison of the Breakdown Behavior of $hbox{In}_{0.52}hbox{Al}_{0.48}hbox{As}$ and InP Near-Infrared Single-Photon Avalanche Photodiodes

We study the breakdown characteristics and timing statistics of InP and $hbox{In}_{0.52}hbox{Al}_{0.48}hbox{As}$ single-photon avalanche photodiodes (SPADs) with avalanche widths ranging from 0.2 to 1.0 $mu{hbox {m}}$ at room temperature using a random ionization path-length model. Our results show that, for a given avalanche width, the breakdown probability of $hbox{In}_{0.52}hbox{Al}_{0.48}hbox{As}$ SPADs increases faster with overbias than InP SPADs. When we compared their timing statistics, we observed that, for a given breakdown probability, InP requires a shorter time to reach breakdown and exhibits a smaller timing jitter than $hbox{In}_{0.52}hbox{Al}_{0.48}hbox{As}$ . However, due to the lower dark count probability and faster rise in breakdown probability with overbias, $hbox{In}_{0.52}hbox{Al}_{0.48}hbox{As}$ SPADs with $hbox{avalanche} hbox{widths}leq 0.5 mu{hbox {m}}$ are more suitable for single-photon detection at telecommunication wavelengths than InP SPADs. Moreover, we predict that, in InP SPADs with $hbox{avalanche} hbox{widths}leq 0.3 mu{hbox {m}}$ and $hbox{In}_{0.52}hbox{Al}_{0.48}hbox{As}$ SPADs with $hbox{avalanche} hbox{widths}leq 0.2 mu{hbox {m}}$, the dark count probability is higher than the photon count probability for all applied biases.