Sr0.5Zr2（PO4）3陶瓷的力学性能研究

用共沉淀法和低分子有机溶剂分散获得SZP粉体，经干压成型和烧结得到SZP陶瓷。研究了其力学性能与烧结温度烧结时间和添加剂用量的关系。最佳工艺条件为：添加Mg06wt%,1300℃或Zn03wt%,1200℃均烧结1．5小时，SZP陶瓷的抗压强度分别可达244．0MPa和226．2MPa。     

K2CO3和CaCO3对低温制备SiC多孔陶瓷性能的影响

采用固相反应法制备SiC多孔陶瓷,通过添加二元复合烧结助剂K₂CO₃和CaCO₃与SiC在空气气氛下氧化生成的SiO₂在较低温度下生成低共融相,促进SiC多孔陶瓷在1100℃-1200℃温度下烧成。研究烧成温度、K₂CO₃和CaCO₃添加量对SiC多孔陶瓷的抗弯强度、显气孔率、气体渗透率、相组成和显微结构的影响。结果表明：当K₂CO₃和CaCO₃添加量分别为1wt%和1wt%,在空气气氛下1100℃保温3h制备的样品综合性能较佳,抗弯强度为33.6MPa,显气孔率为36.3%,气体渗透率为728m³/(m²·h·KPa)。     

热压烧结制备原位复合（TiB2+TiC）/Ti3SiC2复相陶瓷

采用热压烧结法制备了原位复合(TiB2+TiC)/Ti3SiC2复相陶瓷。采用X射线衍射、扫描电镜和透射电镜对材料的物相组成和显微结构进行了表征,研究了烧结温度对材料物相组成、烧结性能、显微结构与力学性能的影响。结果表明:烧结温度在1 350～1 500℃范围内,随着烧结温度的升高,合成反应进行逐渐完全,材料的密度、抗弯强度和断裂韧性显著提高。1 500℃烧结可得到致密的原位复合(TiB2+TiC)/Ti3SiC2复相陶瓷,材料晶粒发育较完善,层片状Ti3SiC2、柱状TiB2与等轴状TiC晶粒清晰可见,增强相晶粒细小,晶界干净,材料的抗弯强度、断裂韧性和Vickers硬度分别达到741 MPa,10.12 MPa.m1/2和9.65 GPa。烧结温度达到1 550℃时Ti3SiC2开始发生分解,材料的密度和力学性能又显著下降。     

3YPSZ-Al2O3-Co3O4陶瓷力学性能的研究

为了提高3YPSZ陶瓷的强度和韧性,先研究了Al2O3的加入量对3YPSZ陶瓷力学性能的影响,结果表明,当Al2O3含量为25wt%时,3YPSZ陶瓷综合力学性能最佳,抗弯强度为582.4MPa,维氏硬度15.4GPa,断裂韧性为6.6MPa.m1/2。再将Al2O3的含量控制在25wt%,通过改变Co(NO3)2.6H2O添加剂的含量来研究3YPSZ-25wt%Al2O3陶瓷材料力学性能的变化,研究发现,当Co3O4的引入量为0.25wt%时,3YPSZ-25wt%Al2O3陶瓷材料综合力学性能最佳,抗弯强度为623.5MPa,维氏硬度为16.9GPa,断裂韧性为7.2MPa.m1/2。并利用XRD和SEM等表征方法分析了Co(NO3)2.6H2O添加剂对材料力学性能和显微组织结构的影响。     

纳米莫来石的制备及其对氧化铝陶瓷性能的影响

以硝酸铝和硅溶胶为原料,采用溶胶-凝胶法合成了纳米莫来石粉体,进而探讨了纳米莫来石对氧化铝陶瓷烧结性能、抗弯强度以及抗热震性能的影响.结果发现,在1100 ℃煅烧硝酸铝与硅溶胶先驱体时仅有少量Al2O3生成,当将煅烧温度升高到1200 ℃时,获得了单一的莫来石晶相,粉体的平均粒径在50～60 nm之间;在氧化铝中添加2wt%～10wt%的纳米莫来石,可以有效促进陶瓷体的致密烧结,并获得良好的抗弯强度与抗热震性能;纳米莫来石含量为5wt%的陶瓷,在1650 ℃烧结后的抗弯强度为247.49 MPa,经过1200 ℃热震后的抗弯强度为218.52 MPa;当纳米莫来石的添加量超过10wt%时,将降低陶瓷的饱和体积密度,并恶化陶瓷的抗弯强度与抗热震性能.     

低温热压制备高硬度、高韧性Si3N4–SiCw–ZrB2陶瓷

通常低温热压烧结的Si₃N₄陶瓷具有较高的硬度和较低的断裂韧性;而高温热压烧结的Si₃N₄陶瓷具有较低的硬度和较高的断裂韧性。为了获得高硬度、高韧性Si₃N₄陶瓷,添加20%SiC_w（SiC晶须,体积分数）和2.5%ZrB2,在1 500℃低温热压制备了Si₃N₄基陶瓷,开展其相组成、致密度、显微结构和力学性能研究,并与1 800℃高温热压烧结Si₃N₄进行了对比研究。结果表明：SiC_w的引入阻碍了Si₃N₄低温致密化,致密度从97.9%降低到92.9%,Vickers硬度从20.5 GPa降低到16.4 GPa,断裂韧性从2.9 MPa·m^1/2增加到3.4 MPa·m^1/2。同步引入SiC_w和ZrB₂     

原位合成磷酸铝助烧剂制备轻质氧化铝空心球陶瓷

采用氧化铝空心球和α Al2 O3微粉为原料 ,以磷酸溶液为结合剂制备了轻质氧化铝空心球陶瓷。研究结果表明 ,磷酸与α Al2 O3微粉原位反应生成的磷酸铝能促进轻质氧化铝空心球陶瓷的烧结 :以浓度 2 5wt%的磷酸为结合剂并经 90 0℃保温 4h烧结后的轻质氧化铝空心球陶瓷 (密度为 1.4g·cm- 3) ,耐压强度达 11.8MPa ,可直接用于窑炉砌筑 ,并可在使用过程中通过二次烧结进一步提高其强度 ;以浓度为 5 0wt%的磷酸结合并经 170 0℃保温4h烧结后的轻质氧化铝空心球陶瓷 (密度为 1.4g·cm- 3) ,耐压强度达到 2 2 .8MPa ,荷重软化温度超过170 0℃ (0 .1MPa)。     

MgO-TiO_2-La_2O_3系氧化铝陶瓷的力学性能及物相分析

采用MgO-TiO2-La2O3为烧结助剂,利用低温烧结技术制备95氧化铝瓷。研究了烧成温度和助剂含量对氧化铝陶瓷力学性能及物相组成的影响。结果表明:在MgO含量为1.5wt%,TiO2为1.0wt%,La2O3为2.5wt%,1500℃保温2h可得到抗弯强度和硬度分别为348.94MPa和79.6HRA的氧化铝陶瓷。     

Si3N4粉粒度对振荡压力烧结Si3N4陶瓷的影响

为了提高Si₃N₄陶瓷的烧结致密度,采用振荡压力烧结工艺分别在1 745和1 775℃制备了Si₃N₄陶瓷,主要研究了Si₃N₄粉的粒度（平均粒径分别为0.4、2.0、2.3μm）对Si₃N₄陶瓷的显微结构和性能的影响。结果显示：1)在两种温度的振荡压力烧结工艺下,由三种不同粒度的Si₃N₄粉制备的Si₃N₄陶瓷的相对密度都很大,为99.65%～99.86%,彼此相差很小。2)由平均粒径为0.2μm的Si₃N₄粉在1 745℃烧结制备的试样的微观结构最均匀,其β-Si₃N₄晶粒平均长径比、抗弯强度和维氏硬度均最大,分别达到5.0、（1 364±65） MPa和（15.72±0.8） GPa;由平均粒径为2.3μm的Si₃     

(Mg0.2Co0.2Ni0.2Cu0.2Zn0.2)Fe2O4高熵陶瓷的制备与吸波性能

采用固相反应法制备了单相块体(Mg_0.2Co_0.2Ni_0.2Cu_0.2Zn_0.2)Fe₂O₄高熵尖晶石陶瓷。结合X射线衍射，扫描电子显微镜和能谱仪对制备过程中的物相组成、显微结构和元素分布进行分析。随烧结温度的升高陶瓷材料体积密度增大，气孔率降低，1 200℃烧结所得致密高熵尖晶石陶瓷材料呈单相，元素均匀分布，其弯曲强度和断裂韧性分别达43.00 MPa和1.30 MPa·m^1/2。所制备高熵尖晶石陶瓷对电磁波兼具介电损耗和磁损耗能力，其在3.0 mm处可获得最大的有效吸收带宽为12.37 GHz，是具有一定承载能力和优异宽频吸波性能的陶瓷材料。     

Photocatalytic activity of Cu2O/TiO2, Bi2O3/TiO2 and ZnMn2O4/TiO2 heterojunctions

Cu₂O/TiO₂, Bi₂O₃/TiO₂ and ZnMn₂O₄/TiO₂ heterojunctions were studied for potential applications in water decontamination technology and their capacity to induce an oxidation process under VIS light. UV–vis spectroscopy analysis showed that the junctions-based Cu₂O, Bi₂O₃ and ZnMn₂O₄ are able to absorb a large part of visible light (respectively, up to 650, 460 and 1000 nm). This fact was confirmed in the case of Cu₂O/TiO₂ and Bi₂O₃/TiO₂ by photocatalytic experiments performed under visible light. A part of the charge recombination that can take place when both semiconductors are excited was observed when a photocatalytic experiment was performed under UV–vis illumination. Orange II, 4-hydroxybenzoic and benzamide were used as pollutants in the experiment. Photoactivity of the junctions was found to be strongly dependent on the substrate. The different phenomena that were observed in each case are discussed.     

ZrO2/SiO2- and La2O3/Al2O3-supported platinum catalysts for CH4/CO2 reforming

Surface-phase ZrO₂ on SiO₂ (SZrOs) and surface-phase La₂O₃ on Al₂O₃ (SLaOs) were prepared with various loadings of ZrO₂ and La₂O₃, characterized and used as supports for preparing Pt/SZrOs and Pt/SLaOs catalysts. CH₄/CO₂ reforming over the Pt/SZrOs and Pt/SLaOs catalysts was examined and compared with Pt/Al₂O₃ and Pt/SiO₂ catalysts. CO₂ or CH₄ pulse reaction/adsorption analysis was employed to elucidate the effects of these surface-phase oxides.

The zirconia can be homogeneously dispersed on SiO₂ to form a stable surface-phase oxide. The lanthana cannot be spread well on Al₂O₃, but it forms a stable amorphous oxide with Al₂O₃. The Pt/SZrOs and Pt/SLaOs catalysts showed higher steady activity than did Pt/SiO₂ and Pt/Al₂O₃ by a factor of three to four. The Pt/SZrOs and Pt/SLaOs catalysts were also much more stable than the Pt/SiO₂ and Pt/Al₂O₃ catalysts for long stream time and for reforming temperatures above 700 °C. These findings were attributed to the activation of CO₂ adsorbed on the basic sites of SZrOs and SLaOs.     

Al_2(SO_4)_3/FeCl_3催化合成乙酸异戊酯

以冰乙酸和异戊醇为原料,Al_2(SO_4)_3/FeCl_3为催化剂,对催化合成乙酸异戊酯的条件进行研究。考察催化剂用量、乙酸与异戊醇物质的量比以及反应时间对乙酸酯化率的影响。结果表明,Al_2(SO_4)_3/FeCl_3具有良好的催化活性,在乙酸物质的量为0.1 mol、乙酸与异戊醇物质的量比为1∶4、催化剂用量1.0 g、反应时间2.0 h和带水剂环己烷用量10 m L反应条件下,重复实验3次,平均乙酸酯化率为93.50%。     

稀土固体超强酸SO2-4/TiO2/La3+催化合成醋酸丁酯

研究了以固体超强酸SO24-/TiO2/La3+催化剂,醋酸和正丁醇为原料合成醋酸丁酯,并考察了影响反应的因素.结果表明醇酸物质的摩尔比为1.61、催化剂用量0.6 g、带水剂甲苯7 mL、反应时间2.5 h是最适宜的反应条件,其酯化率可达96.2%.     

K_2SO_4对V_2O_5/TiO_2脱硝催化剂表面形态的影响

采用XRD和XPS对新鲜的和K2SO4掺杂的V2O5/TiO2脱硝催化剂的表面形态进行了分析。结果表明,K2SO4的掺杂未对V与Ti之间的相互作用造成显著的影响,但是引起催化剂表面V和Ti的浓度降低,V5+在催化剂表面消失。K与钒氧物种上的晶格氧发生了强烈的相互作用。     

Electrocatalyst materials for fuel cells based on the polyoxometalates—K7 or H7[(P2W17O61)Fe(H2O)] and Na12 or H12[(P2W15O56)2Fe4(H2O)2]

Free acids of the iron substituted heteropoly acids (HPA), H₇[(P₂W₁₇O₆₁)Fe^III(H₂O)] (HFe1) and H₁₈[(P₂W₁₅O₅₆)₂Fe^III₂(H₂O)₂] (HFe2) were prepared from the salts K₇[(P₂W₁₇O₆₁)Fe^III(H₂O)] (KFe1) and Na₁₂[(P₂W₁₅O₅₆)₂Fe^III₄(H₂O)₂] (NaFe4), respectively. The iron-substituted HPA were adsorbed on to XC-72 carbon based GDLs to form HPA doped GDEs after water washing with HPA loadings of ca. 1 μmol. The HPA was detected throughout the GDL by EDX. Solution electrochemistry of the free acids are reported for the first time in sulfate buffer, pH 1-3. The hydrogen oxidation reaction was catalyzed by KFe1 at 0.33 V, with an exchange current density of 38 mA/cm². Moderate activity for the oxygen reduction reaction was observed for the iron substituted HPA, which was dramatically improved by selectively removing oxygen atoms from the HPA by cycling the fuel cell cathode under N₂ followed by reoxidation to give a restructured oxide catalyst. The nanostructured oxide achieved an OCV of 0.7 V with a Tafel slope of 115 mV/decade. Cycling the same catalysts in oxygen resulted in an improved catalyst/ionomer/carbon configuration with a slightly higher Tafel slope, 128 mV/decade but a respectable current density of 100 mA/cm² at 0.2 V.     

Properties of char particles obtained under O2/N2 and O2/CO2 combustion environments

Pulverized coal combustion in O₂/N₂ and O₂/CO₂ environments was investigated with a drop tube furnace. Results present that the reaction rate and burn-out degree of O₂/CO₂ chars (obtained in O₂/CO₂ environments) are lower than that of O₂/N₂ chars (obtained in O₂/N₂ environments) under the same experimental condition. It indicates that a higher O₂ concentration in O₂/CO₂ environment is needed to achieve the similar combustion characteristic to that in O₂/N₂ environment. The main differences between O₂/N₂ and O₂/CO₂ chars rely on the pore structure determined by N₂ adsorption and chemical structure measured by FT-IR. For O₂/CO₂ char, the surface is thick and the pores are compact which contribute to the fragmentation reduction of particles burning in O₂/CO₂ environment. The organic functional group elimination rate from the surface of O₂/CO₂ chars is slower or delayed. The present research results might have important implications for further understanding the intrinsic kinetics of pulverized coal combustion in O₂/CO₂ environment.     

New acrylic monolithic carbon molecular sieves for O2/N2 and CO2/CH4 separations

The modification of activated carbon fibres prepared from a commercial textile acrylic fibre into materials with monolithic shape using phenolic resin as binder was studied. The molecular sieving properties for the gas separations CO₂/CH₄ and O₂/N₂ were evaluated from the gas uptake volume and selectivity at 100 s contact time taken from the kinetic adsorption curves of the individual gases. The pseudo-first order rate constant was also determined by the application of the LDF model. The samples produced show high CO₂ and O₂ rates of adsorption, in the range 3-35 × 10⁻³ s⁻¹, and in most cases null or very low adsorption of CH₄ and N₂ which make them very promising samples to use in PSA systems, or similar. Although the selectivity was very high, the adsorption capacity was low in certain cases. However, the gas uptake in two samples reached 23 cm³ g⁻¹ for CO₂ and 5 cm³ g⁻¹ for O₂, which can be considered very good. The materials were heat-treated using a microwave furnace, which is a novel and more economic method, when compared with conventional furnaces, to improve the molecular sieves properties.     

Solid state metathesis synthesis of BaTiO3, PbTiO3, K0.5Bi0.5TiO3 and Na0.5Bi0.5TiO3

A solid state metathesis approach has been applied to synthesize perovskite oxides such as BaTiO₃, PbTiO₃, K_0.5Bi_0.5TiO₃ and Na_0.5Bi_0.5TiO₃, these were characterized by powder XRD, IR and energy dispersive spectra (EDS). Potassium titanium oxalate and metal chlorides are used as the starting materials. X-ray analysis shows the formation of a single phase with tetragonal structure for BaTiO₃, PbTiO₃, K_0.5Bi_0.5TiO₃ and a monoclinic structure for Na_0.5Bi_0.5TiO₃. The Infrared spectra of these compounds show the characteristic band due to Ti–O octahedron for all the compounds. The EDS spectra show the relative ratio of the metal ions. The morphology of synthesized compounds was obtained from SEM measurements.