石墨干膜润滑剂在碳钢表面摩擦磨损性能试验研究*

传统油或脂润滑剂在极端工况环境下无法满足碳钢类零件的减摩要求,采用干膜润滑剂是提高极端工况环境下碳钢表面摩擦磨损性能的可行性方法。采用超声波分散方法制备以石墨粉末为基体的干膜润滑剂,使用压力喷涂技术使其沉积在碳钢试件表面,在端面摩擦试验仪中开展干摩擦和石墨干膜润滑剂润滑下摩擦磨损性能对比性试验研究。试验结果表明：石墨干膜润滑剂在碳钢表面的沉积效果较好,沉积的石墨干膜润滑剂具有较好的润滑性能,可以有效地保护碳钢表面不被过度磨损;喷涂石墨干膜润滑剂的碳钢试件的工作寿命随着压力载荷和主轴转速的增大而缩短,负载和滑动速度的联合作用会加速涂层向稳定方向的过渡;磨损过程中形成的微观润滑剂颗粒会形成颗粒流润滑,适当添加石墨颗粒粉末可能会延长润滑剂正常发挥减摩作用的时间。制备的石墨干膜润滑剂为碳钢在极端工况环境下的减摩提供了支持。     

固体润滑涂层在干摩擦及有油条件下的摩擦磨损性能

采用MRH-3环块磨损试验机对FM-510二硫化钼润滑涂层在于摩擦及有油条件下进行了摩擦磨损性能的考察和评价,评价结果表明：该涂层在干摩擦条件下具有低的摩擦系数、高的承载能力和长的耐磨寿命,摩擦系数随负荷增高而降低,随速度提高也降低。摩擦偶对双面涂膜比单面涂膜有更长的耐磨寿命,速度低时涂层的磨耗小,寿命长,可满足特定条件下的干摩擦工作要求,在有油润滑条件下二硫化钼基的FM-510润滑涂层可显减轻对偶磨损程度,摩擦系数比单独使用油润滑时大大降低。在难以形成连续的流体润滑薄膜,亦即不能形成流体动力润滑的情况下。摩擦偶对涂敷固体润滑涂层是解决其润滑问题的有效方案。     

脂肪醇对Ti6Al4V/钢摩擦副摩擦磨损性能的影响

采用SRV型摩擦磨损试验机分别考察了Ti6Al4V/钢摩擦副在多种脂肪醇润滑下的摩擦磨损性能。结果表明,与液体石蜡相比,碳链长度小于碳8的脂肪醇作为Ti6Al4V/钢摩擦副的润滑剂表现出良好的润滑性能,其润滑机制是在Ti6Al4V磨损表面形成吸附膜。载荷和频率明显影响Ti6Al4V/钢摩擦副在脂肪醇润滑下的摩擦磨损行为和摩擦磨损机制:当载荷较小时,Ti6Al4V磨损表面主要发生轻微的擦伤;随着载荷增加,Ti6Al4V磨损表面擦伤严重并在更高载荷下发生较为严重犁沟和塑性变形。     

The Effect of Different Temperatures on Friction and Wear Properties of CFRPEEK against AISI 431 Steel under Water Lubrication

The tribological behavior of 30 vol% carbon fiber–reinforced polyetheretherketone (CFRPEEK) against AISI 431 steel under different temperatures of water lubrication was investigated. Friction and wear tests were carried out on a disc-on-disc contact test apparatus under different operating conditions. The results reveal that the lubricant temperature has a significant effect on the friction and wear properties of CFRPEEK sliding against AISI 431 steel. The average friction coefficient and wear rate of CFRPEEK increase with increasing lubricant temperature. However, the wear rate of AISI 431 steel did not have a positive correlation with the wear rate of CFRPEEK under different temperatures of water lubrication. Moreover, the original and worn surfaces of CFRPEEK and AISI 431 steel were imaged by environmental scanning electron microscopy and optical microscopy, respectively. The main tribological mechanisms of CFRPEEK sliding against AISI 431 steel were adhesive wear, and increasing the temperature of the lubricant could accelerate wear.     

Boundary Lubrication of Steel Surfaces with Borate,Phosphorus, and Sulfur Containing Lubricants at Relatively Low and Elevated Temperatures

Prolonging the life of engineering components through lubricant formulation to achieve better wear resistance and higher oxidation stability is of paramount importance to many mechanical systems, such as automotive gears and bearings. This can be accomplished with formulated lubricants that limit the generation of wear debris causing severe abrasion and protect the contacting surfaces through the formation of wear-resistant tribofilms. In this study, a ball-on-disk tribometer was used to characterize the friction and wear properties of steel surfaces slid in the boundary lubrication regime. An experimental scheme was developed to allow the statistical screening of various lubricant formulations. Sliding experiments were performed in baths of different lubricants at relatively low and elevated temperatures, approximately 32 and 100°C, respectively, under conditions of constant load and sliding speed. Surface profilometry, optical microscopy, and scanning electron microscopy were used to characterize the dominant friction and wear mechanisms. The tribological properties were found to strongly depend on the temperature and the additives (e.g., borate, phosphorus, and sulfur) present in the blended lubricants. The superior high-temperature wear performance of the lubricant with the higher borate content is indicative of the formation of a durable tribofilm that reduces metal-to-metal adhesion, material transfer, and surface plowing by wear debris.     

Failure criteria in thin film lubrication with EP additives

The scuffing behaviour of sliding couples made from 12 NiCr 13 steel, lubricated with SAE 90 and SAE 20 W30 oils with and without additives, was studied as a function of relative sliding speed and bulk oil temperature. It was found that the scuffing load decreases almost inversely with sliding speed. Calculations which take into account the decrease in hardness at increasing temperature show a fairly good constancy of total contact temperature (bulk + flash temperature) at scuffing (i.e. values ranging from 550 ° to 650 °C for all oils and test conditions). At low speeds (up to 1 m s^?1) a well-defined increase in scuffing load was found when EP additives were used; at higher speeds this effect was found to have vanished completely. Variations in nominal contact pressure in the range 1 to 3 had no appreciable influence on the scuffing load, indicating that, in the present case, scuffing was associated with a transition from the boundary lubrication regime to the severe wear regime.     

Grooved surface texturing by electrical discharge machining (EDM) under different lubrication regimes

The aim of the present research work was to investigate the effectiveness of grooved surface texturing with a rhombic geometry under different lubrication regimes. Tribological investigation under unidirectional sliding was focused on the effect of texturing parameters including pattern area density on the coefficient of friction under different lubrication regimes, achieved by varying sliding speed and lubricant viscosity. Grooved patterns with different textured area densities were produced on steel samples by electrical discharge machining. Results of this investigation showed that under boundary lubrication, textures resist sliding thus resulting in increased friction. The largest improvement of friction reduction was observed under hydrodynamic lubrication, for low‐viscosity oil when using the textured disc with 21% pattern area density. The reduction of the coefficient of friction if compared with the untextured surface was of approximately 24%. Examination of the sliding surfaces has not shown any quantifiable wear for the contact conditions studied.     

Determination of load carrying ability of chemical films developed in sliding point contact

It has already been known for many years that the use of some extreme-pressure (EP), antiwear or friction modifier (FM) additives in mineral oils can produce different kind of boundary or chemical reaction films on sliding contact surfaces of some kinds of steel in boundary lubrication conditions. Using a sliding ball-on-disc configuration lubricated with some kinds of EP or FM, the wear scars on the balls can always reach the same limit size at a specified applied load and sliding velocity. From the fact that the limit sizes of wear scars decrease as sliding speed is increased or applied load is decreased, the load carrying ability of a chemical film can be obtained by extrapolating the data to the condition of zero sliding speed and is so defined that if the contact pressure is greater than this load carrying ability, the contact surfaces will continuously be worn; if the contact pressure is smaller than it, no more wear will occur on the surfaces. Based on this load carrying ability, the hydrodynamic effect of sliding pairs can also be identified. Therefore, the limit size of wear scar at specified sliding speed and applied load can also be predicted in a mixed lubrication condition.     

Stribeck Curve Under Friction of Copper Samples in the Steady Friction State

The friction and wear of a pure copper block (99.98 wt% Cu) against a hardened steel disc were studied. The effect of sliding velocity and load on the friction coefficient and wear rate of Cu samples during steady tests was studied. Elasto-hydrodynamic (EHL), mixed (ML) and boundary lubrication (BL) regions were analyzed using the Stribeck curve. The lubrication number of Schipper, Z, was used in the analysis of the Stribeck curve. The transitions from one lubrication region to another are discussed. The mixed EHL region is characterized by stable low values of the friction coefficient, wear rate and temperature. Straight asperity contact is the dominant mechanism under friction of Cu–steel pair in the BL region. High-friction coefficients and wear rates, thin lubricant films and large wear grooves indicate straight asperity contact between rubbed surfaces in the BL region. Although the dominant mechanisms in the mixed EHL and BL regions are different in principle, a steady friction state is preserved in both cases. It is expected that the steady friction state in the BL and mixed EHL regions is associated with deformation and fracture of surface layers but these process occur at different scale levels. It was shown that under friction of Cu–steel pair, two types of ML regions are observed. The first is the stable steady friction of mixed EHL with low values of the friction coefficient and wear rate. The second type of the ML region is the region of unstable friction and wear when a decrease of lubricant film leads to a change of external (roughness, temperature, friction and wear) and internal (strain and stress) parameters. It was found out that a transition to the unstable ML region occurs within a narrow range of Z parameter under definite values of the load and sliding velocity.     

一种新型摩擦材料在水润滑下的摩擦学性能研究

采用环块式摩擦磨损实验研究了一种新型摩擦材料在水润滑状态下不同载荷与转速对试样摩擦学性能的影响,并对比干摩擦条件下的摩擦学性能变化,借助磨损表面形貌观察分析其磨损机理。实验结果表明:水润滑条件下,摩擦系数随着载荷的增大而减小,随着转速的提高先增加后减小;磨损率随着载荷与转速的提高都减小。相同载荷与转速下,干摩擦时磨损机理以磨粒磨损和黏着磨损为主,而水润滑条件下水形成边界润滑,磨损机理以磨粒磨损和轻微的黏着磨损为主;水润滑条件下摩擦系数和磨损率均低于干摩擦,主要是由于水起到了润滑和冷却的作用,阻止了转移膜的形成,并在材料表面形成水膜起到了边界润滑的作用。     

An Investigation into Lubrication and Oxide Breakdown During Load-Carrying Capacity Testing

Changes occurring in the friction and wear mechanisms during a load-carrying capacity test, lubricated with cetane containing a carboxylic acid, were investigated. The changes in wear scar/track appearance and oxide coverage/composition were analyzed during every load stage.

The main conclusions were as follows:

• The breakdown in the protective oxide layer formed on the opposing steel surfaces was found to be the prerequisite for initiation of seizure.

• The seizure load achieved during load-carrying capacity testing quantifies the ability of the test fluid to prevent transition to the adhesive wear regime.

• The most severe surface damage was found to occur during the first few seconds after test initiation. Desorption of the adsorbed lubricant film and the subsequent removal of the naturally occurring thin oxide layer results in the initial period of adhesive wear.

• Partial recovery to a state of acceptable friction occurs after the period of initial seizure. During this period, the surface coverage by the adsorption lubricant molecules and the oxide coverage are sufficient to prevent severe adhesive wear from occurring. Wear is primarily a combination of oxidative, abrasive, and fatigue wear (all possible in the regions of mixed friction and boundary lubrication).

• Final lubricant breakdown and eventual seizure are initiated when the oxide removal rate exceeds the oxide formation rate resulting in severe adhesive wear followed by seizure.

     

有机钼复合润滑剂在高温微动和滑动条件下的摩擦磨损行为

以矿物基650SN油作为基础油,采用复配技术制备了有机钼复合润滑剂。利用SRV微动磨损试验机和T-11滑动磨损试验机考察了该复合剂的高温摩擦学行为,采用扫描电子显微镜和X射线光电子能谱仪对其润滑下的磨痕表面形貌和表面膜的元素组成进行了分析,探讨了复合剂的减摩润滑机制。结果表明:有机钼复合剂具有良好的高温微动和滑动摩擦学行为,与基础油相比,复合剂能够使钢-钢摩擦副在高温微动和滑动过程中的摩擦因数降低28%和43%,抵抗微动和滑动磨损的能力分别提高53%和54%。这是由于有机钼复合剂通过分解、吸附和摩擦化学反应,在摩擦副金属表面形成了含磷酸盐的沉积膜和含FeS、MoS2的化学反应膜共同组成的复合边界润滑膜,从而表现出优良的减摩润滑效果。     

Failure criteria in thin film lubrication: Investigation of the different stages of film failure

The mechanisms of failure of sliding lubricated concentrated steel contacts have been studied using a newly developed tribometer which allows fast separation of the sliding surfaces at the different stages of film failure. The appearance of the corresponding contact topography was investigated by means of optical interference microscopy. The results indicate a gradual transition from full to partial elastohydrodynamic (EHD) lubrication as a function of increasing load and increasing bulk oil temperature until complete failure of the EHD film occurs at critical triplets of normal load, sliding velocity and bulk oil temperature.     

Super low friction of DLC applied to engine cam follower lubricated with ester-containing oil

This paper presents a material combination that reduces the friction coefficient markedly to a superlow friction regime (below 0.01) under boundary lubrication. A state approaching superlubricity was obtained by sliding hardened steel pins on a hydrogen-free diamond-like carbon (DLC) film (ta-C) lubricated with a poly-alpha-olefin (PAO) oil containing 1 mass% of an ester additive. This ta-C/steel material combination showed a superlow friction coefficient of 0.006 at a sliding speed of 0.1 m/s. A hydrogencontaining DLC coating/steel combination also showed a lower friction coefficient in air than a steel/steel combination, 0.1 vs. 0.8, but no large reduction was observed when the sliding surfaces were lubricated with ordinary 5W-30 engine oil and the PAO oil containing an ester additive. The friction coefficient of the hydrogen containing DLC/steel combination lubricated with the PAO containing an ester additive was above 0.05. On the other hand, the superlow friction performance demonstrates that the rolling contact friction level of needle roller bearings can be obtained in sliding contact under a boundary lubrication condition. It is planned to apply this advanced DLC coating technology to valve lifters lubricated with a newly formulated engine oil in actual mass-produced gasoline engines. A larger friction reduction of more than 45% is expected to be obtained at an engine speed of 2000 rpm.     

Investigation into sliding wear performance of zinc-based alloy reinforced with SiC particles in dry and lubricated conditions

The objective of the present investigation was to assess the influence of SiC particle dispersion in the alloy matrix, applied load, and the presence of oil and oil plus graphite lubricants on the wear behaviour of a zinc-based alloy. Sliding wear performance of the zinc-based alloy and its composite containing SiC particles has been investigated in dry and lubricated conditions. Base oil or mixtures of the base oil with different percentages of graphite were used for creating the lubricated conditions. Results show a large improvement in wear resistance of the zinc-based alloy after reinforcement with SiC particles. The lubrication improved the wear resistance and friction behaviour of both the reinforced and base alloys. It was also observed that there exists an optimum concentration of graphite particles in the lubricant mixture that leads to the best wear performance. The composite experienced higher frictional heating and friction coefficient than the matrix alloy in all the cases except oil lubricated conditions; a mixed trend was noticed in the latter case. The wear rate and frictional heating increased with load while friction coefficient was affected in an opposite manner. Test duration influenced the frictional heating and friction coefficient of the samples in a mixed manner.Examination of worn surfaces revealed a change of predominating wear mechanisms from severe ploughing and/or abrasive wear for base alloy to delamination wear for the reinforced material under dry sliding conditions. The presence of the lubricant increased the contribution of adhesive wear component while reducing the severity of abrasion. This was attributed to the generation of more stable lubricant films on the contacting surfaces. Cross-sections of worn surfaces indicated substantial wear-induced plastic deformation, thereby suggesting adhesive wear to be a predominant wear mechanism in this study. The debris particles revealed deformed flakes and machining chips signifying the involvement of adhesion and abrasion modes of wear respectively.     

Tribological properties of few-layer graphene oxide sheets as oil-based lubricant additives

The performance of a lubricant largely depends on the additives it involves. However, currently used additives cause severe pollution if they are burned and exhausted. Therefore, it is necessary to develop a new generation of green additives. Graphene oxide (GO) consists of only C, H and O and thus is considered to be environmentally friendly. So the tribological properties of the few-layer GO sheet as an additive in hydrocarbon base oil are investigated systematically. It is found that, with the addition of GO sheets, both the coefficient of friction (COF) and wear are decreased and the working temperature range of the lubricant is expanded in the positive direction. Moreover, GO sheets has better performance under higher sliding speed and the optimized concentration of GO sheets is determined to be 0.5wt%. After rubbing, GO is detected on the wear scars through Raman spectroscopy. And it is believed that, during the rubbing, GO sheets adhere to the sliding surfaces, behaving like protective films and preventing the sliding surfaces from contacting with each other directly. This paper proves that the GO sheet is an effective lubricant additive, illuminates the lubrication mechanism, and provides some critical parameters for the practical application of GO sheets in lubrication.     

浸酚醛树脂石墨/SiC密封材料摩擦学特性研究

采用UMT-3多功能摩擦磨损试验机研究了3种国产典型浸酚醛树脂石墨与SiC陶瓷配对副在干摩擦和油润滑条件下的摩擦学特性,结果表明:干摩擦下,摩擦因数随载荷p与速度v的乘积(pv值)的增大呈下降趋势;pv值较小时,磨损机理主要为轻微黏着磨损和磨粒磨损,pv值较大时则变为严重黏着磨损、磨粒磨损和疲劳磨损;相同条件下的磨损率...     

Temperature—friction characteristics of cylinder lubrication in large,slow, cross‐head marine diesel engines under boundary lubrication conditions

In large, slow, cross‐head marine diesel engines research has increasingly shown that the lubrication regime between piston rings and cylinder liner at top dead centre is of the boundary lubrication type due to the high gas pressure, low sliding speed, and high temperature. This means that the tribological properties of piston ring, cylinder liner, and cylinder lubricant in these types of engine under boundary lubrication conditions should be considered simultaneously when friction and wear between the piston ring and cylinder liner are studied. Until now there has been no standard method to evaluate boundary lubrication performance. There are a few traditional methods used in lubricant research, but their results are not correlated with service conditions. It is important to find a suitable method to evaluate the boundary lubrication performance of lubricants at the laboratory testing stage or before the engine testing stage. The important parameters, such as sliding speed, normal load, materials of the contacting pairs, and lubricant, need all to be controlled. In this paper a systematic experimental procedure, the ‘five times heating and cooling test’, is introduced to assess lubricant properties under boundary lubrication conditions. Most of the parameters mentioned above are controlled. The model contact, of pin‐on‐plate form, is made from the actual piston and liner materials used in a large‐bore, slow, cross‐head marine diesel engine. The temperature characteristics of different blends of lubricants are investigated under boundary lubrication conditions using a pin‐on‐plate reciprocating test rig. These blends of lubricants have the same additives but different base fluids; they nevertheless fulfil the physical and chemical requirements of a real marine diesel engine. The test temperature range is from room temperature to the working temperature of the top piston ring. The experiments show that there are different temperature—friction characteristics for lubricants with different bases and the same additive package and there are also different temperature—friction characteristics during heating up and cooling down for each blend. Single‐base lubricants have more promising temperature—friction characteristics than those of a blend of a high‐viscosity base and a low‐viscosity base at high temperature.     

Nanocomposite UHMWPE–CNT Polymer Coatings for Boundary Lubrication on Aluminium Substrates

The boundary lubrication regime plays a very important role in determining the life span of any of the two mating parts under liquid-lubricated conditions. It is during the start\stop cycles when insufficient fluid is available to fully separate the surfaces in relative motion and thus unusual wear takes place; a case of boundary lubrication. The aim of this work is to study the feasibility of using polymer coatings as boundary lubricants. This study investigates the friction and wear properties of ultra-high molecular weight polyethylene (UHMWPE) films coated on aluminium substrates under dry and base oil (without any additives)-lubricated conditions. In order to increase the load bearing capacity of the UHMWPE coatings, 0.1 wt% of single-walled carbon nanotubes are added. Experiments are carried out on a custom-built tribometer simulating a line contact between a polymer-coated cylindrical Al surface (shaft) and a flat uncoated Al plate as the counterface. The experimental parameters such as the normal load and the sliding speed are selected to simulate the boundary and mixed lubrication regimes for comparison purposes. Specific wear rates of the polymer films and bare Al surface under lubricated conditions are also calculated. Stribeck curves have been generated to evaluate the effectiveness of the pristine UHMWPE and the nanocomposite coatings in the various regimes of lubrication, especially the boundary lubrication regime. It is observed that the selected polymer coatings are effective in protecting the metallic surfaces without causing any observable oil contamination with wear debris.     

Transition Temperatures in Sliding Systems

A pin-on-disk type of apparatus is used to study the effect of operating variables on transition temperatures with dilute solutions of pure fatty acids in pure paraffinic hydrocarbons and with a straight paraffinic mineral oil. It is found that the temperature at which the sudden transition from low to high friction and wear occurs increases with sliding speed, decreases with load, and is otherwise independent of operating variables. Empirically, the reciprocal of the absolute transition temperature varies linearly with the logarithm of the ratio of load to speed. The absence of conventional hydrodynamic lubrication in this system is demonstrated.

It is concluded that these results are inconsistent with the widely accepted concept that boundary lubricants must form a “solid” adsorbed film to be effective. It appears necessary to adopt a modified view of the role of the boundary lubricant, in which rheological and other diverse physical characteristics must be considered, and not simply the state of matter in which it exists. In addition, it appears necessary to consider the interrelated kinetics of boundary film formation and welding between asperities.