Single step synthesis of nanosized CeO2–MxOy mixed oxides (MxOy?=?SiO2, TiO2, ZrO2, and Al2O3) by microwave induced solution combustion synthesis: characterization and CO oxidation

Various CeO₂ –M _x O _y (M _x O _y  = SiO₂, TiO₂, ZrO₂, and Al₂O₃) mixed oxides were prepared by microwave induced solution combustion method and analyzed by different complimentary techniques, namely, X-ray diffraction (XRD), Raman spectroscopic (RS), UV–Vis diffuse reflectance spectroscopy (UV-DRS), X-ray photoelectron spectroscopy (XPS), thermogravimetry (TG-DTA), and BET surface area. XRD analyses revealed that CeO₂ –SiO₂ and CeO₂ –TiO₂ mixed oxides are in slightly amorphous form and exhibit only broad diffraction lines due to cubic fluorite structure of ceria. XRD lines due to the formation of cubic Ce_0.5Zr_0.5O₂ were observed in the case of CeO₂ –ZrO₂ sample. RS results suggested defective structure of the mixed oxides resulting in the formation of oxygen vacancies. The UV-DRS measurements provided valid information about Ce⁴⁺ ← O²⁻ and Ce³⁺ ← O²⁻ charge transfer transitions. XPS studies revealed the presence of cerium in both Ce³⁺ and Ce⁴⁺ oxidation states. The ceria–zirconia combination exhibited better oxygen storage capacity (OSC) and CO oxidation activity when compared to other samples. The significance of present synthesis method lays mostly on its simplicity, flexibility, and the easy control of different experimental factors.     

Structure, Phonon Vibration, and Spin Correlation of LaBa2Cu3?xCoxOy

Polycrystalline samples LaBa₂Cu_3–xCo _x O _y (0 x 1.0) were synthesized by solid state reaction method. The structure, phonon vibration, conduction, and spin correlation were investigated by means of X-ray diffraction, infrared spectra, resistivity, and electron spin resonance. It is found that there are orthorhombic–tetragonal and tetragonal–orthorhombic structural transitions with Co doping, and the conduction behavior changes from metallic to semiconducting. With the increase of Co content, the Cu(1)—O(1) phonon mode around 531 cm^–1 softens, the Cu(2)—O(2) phonon mode around 657 cm^–1 hardens, and the Cu(1)—O(4) mode around 583 cm^–1 is nearly unchanged. The Cu²⁺ spins tend to localize with Co doping. The changes in structure, phonon vibration, and spin correlation with Co doping are analyzed and discussed.     

Superconductivity of YBa2?xNdxCu3Oy Solid Solution

The solubility of Nd at the Ba sites and the superconductivity of YBa_2–x Nd _x Cu₃O _y were investigated by X-ray powder diffraction and measurements of the electrical resistance and ac susceptibility. The single Re123 phase was obtained for x0.30. The onset transition temperature is insensitive to the Nd content x in the region of x0.40. All are higher than 95 K. The zero resistance transition temperatures , however, exhibits two-step variation with the increase of x. For x0.25, are all above 92 K. The highest of 94 K was obtained for x=0.25. For x0.3 drops sharply to about 84 K. Finally falls to 30 K and is below 10 K for x=0.5. The two-step variation of T _c might be an indication of the existence of two trap levels for holes.     

The Effect of Silver Substitution in Bi1.7Pb0.3Sr2Ca2?xAgxCu3Oy

The effect of Ag substitution on the properties of high-temperature superconductor Bi_1.7Pb_0.3Sr₂Ca_2−x Ag _x Cu₃O _y system have been investigated. The electrical and structural properties of the samples, prepared by the conventional solid-state reaction method, have been characterized by X-ray diffraction (XRD), electrical resistance and scanning electron microscopy (SEM) studies. XRD analysis reveals a multiphase structure of the samples, whereas SEM micrographs indicate some morphological changes induced by silver addition. It was found that an increase of the amount of Ag₂O addition leads to an enhancement of the critical temperature and the percentage of Bi-2223 phase in the phase mixture.     

Magnetic and dielectric properties of Mg1+x Mnx, Fe2?2x, O4 ferrite system

Ferrites with the general formula Mg_1+xMn_xFe_2–2xO₄(where x = 0.0, 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8 and 0.9) were prepared by the standard ceramic technique and studied by means of X-ray diffraction, magnetization, a.c. susceptibility and dielectric constant measurements. The X-ray analysis confirmed the single-phase formation of the samples. The lattice parameter is found to increase up to x = 0.3 and thereafter it decreases as x increases. The cation distribution has been studied by X-ray analysis and magnetization. Magnetization results exhibit collinear ferrimagnetic structure for x 0.3 and thereafter structure changes into non-collinear for x > 0.3. Curie temperature (T_C) obtained from a.c. susceptibility data decreases with increasing x. The dielectric constant (), loss tangent (tan ) show strong frequency dependence.     

A Study of the Magnetic Properties of?Bi1.64?xPb0.36CdxSr2Ca2Cu3Oy Superconductor

The flux pinning energy and magnetic properties of Bi_1.64−x Pb_0.36Cd _x Sr₂Ca₂Cu₃O _y (BPCSCCO) with x=0.0, 0.02, 0.04 and 0.06 were studied. A series of Bi-2223 superconductor samples with a nominal composition of BPCSCCO was synthesized and the effect of Cd substitution for Bi was investigated. As a result, Cd addition has been found to improve the superconducting properties of the Bi-Pb-Sr-Ca-Cu-O system. The effects of the annealing time and the amount of Cd doping on the structure, AC magnetic susceptibility, ρ–T curves and flux pinning energy were investigated. Also, for all samples the relation between the current and voltage in the mixed state was found to follow the model relationship V=α I ^β . The maximum value of β is 22.30, which is obtained for the sample with an annealing time of 270 h and a Cd content of 0.04.     

The Effects of Substitution of Sn for Cu in Bi1.75Pb0.25Sr2CaCu2.3?xSnxSnxOy

The influence of Sn doping on superconductivity in the Bi-based 2212 phase is studied in this paper. For the samples R–T relations and magnetic hysteresis loops were measured. X-ray powder diffraction analysis was also performed. For Bi_1.75Pb_0.25Sr₂CaCu_2.3–x Sn _x O _y , the experimental results show that by adding the proper amount of Sn the superconductivity of the samples can be improved. As x = 0.15, the critical temperature T _c, the critical current density J _c, and the magnetic pinning force density F reach a maximum. At T = 11 K, the critical state parameters H _c1, H _c2, , , and are calculated and compared with the results reported by other researchers. The experimental results also show that the Sn doping is able to speed up the growth of the 2223 phase. In brief, Sn doping is an effective way of improving the superconductivity in Bi-based superconductors.     

Preparation, characterization and conductivity studies of Li3?2xAl2?xSbx(PO4)3

New NASICON type materials of composition, Li_3−2x Al_2−x Sb _x (PO₄)₃ (x = 0·6 to 1·4), have been prepared and characterized by powder XRD and IR. D.C. conductivities were measured in the temperature range 300–573 K by a two-probe method. Impedance studies were carried out in the frequency region 10²−10⁶ Hz as a function of temperature (300–573 K). An Arrhenius behaviour is observed for all compositions by d.c. conductivity and the Cole-Cole plots obtained from impedance data do not show any spikes on the lower frequency side indicating negligible electrode effects. A maximum conductivity of 4·5 × 10⁻⁶ S cm⁻¹ at 573 K was obtained for x = 0·8 of the Li_3−2x Al_2−x Sb _x (PO₄)₃ system.     

A new series of mercury-based high-Tc superconductors (Hg, W)Sr2(Y1?x Cax)Cu2

A new series of superconducting mercury-based layered cuprates has been synthesized. X-ray diffraction indicates that the compounds with formula Hg_0.8W_0.2Sr₂Y_1–x Ca _x Cu₂O₆₊ (0.3x0.6) exhibit the 1212 structure with space groupP _4/mmm . The investigation of superconductivity determined by electrical resistance measurement shows that the superconducting transition temperature (T _c , onset) of Hg_0.8W_0.2Sr₂Y_0.4Ca_0.6Cu₂O₆₊ is up to 94 K.     

Synthesis and abrasive properties of nanoparticulate MoO2-modified Al2 ? xFexO3 and Fe2 ? yAlyO3 solid solutions

X-ray diffraction, IR spectroscopy, particle-size analysis, and chemical analysis are used to elucidate the general mechanisms of the formation of nanoparticulate molybdenum-dioxide-modified Al_{2 − x} Fe _x O₃ and Fe_{2 − y} Al _y O₃ solid solutions prepared via heat treatment of ammonium hydroxycarbonate complexes, (NH₄)₂Al₂Fe(OH)₅(CO₃) · nH₂O. The addition of molybdenum dioxide (within 0.005 mol %) is shown to enhance the polishing performance of the oxides for final polishing of nonferrous metals and alloys (copper and brass) by a factor of 6–7 relative to unmodified aluminum iron oxides, which is attributable to the increased chemical activity of the abrasive material. The surface roughness value R _a achieved is below 0.005 μm.     

New Pb-based 1212 Cuprate Superconductors Containing Sulfur, (Pb0.75S0.25)Sr2 (Y1?xCax)Cu2Oz

New Pb-based 1212 layered cuprates containing sulfur have been synthesized in the (Pb_0.75S_0.25) Sr₂ (Y_1−x Ca _x ) Cu₂O _z system. X-ray diffraction analysis shows that the almost single-phase samples are obtained within a region of 0.0≤x≤0.5. The crystal structure of each sample has a tetragonal symmetry with the typical lattice constants a=0.3837 nm and c=1.186 nm. As Ca content x is increasing, the semiconductor-like behavior is suppressed. But after only annealing under ambient O₂ pressure, none of the samples show any trace of superconductivity. On the other hand, when the samples are annealed under high O₂ pressure of about 13.6 MPa, they show resistivity dropping phenomenon in a region of 0.5≤x≤0.7. Among them, the lowest resistivity sample with x=0.6 has an onset temperature of the resistivity dropping at about 22.5 K. Moreover, this sample shows a diamagnetic signal at about 21.5 K. These phenomena are attributed to superconductivity.     

Electrical and magnetic properties of the diluted magnetic semiconductors Cd1 ? xMnxGeP2 and Cd1 ? xMnxGeAs2 at high pressures

The structural and magnetic phase transitions and magnetoresistance of the diluted magnetic semiconductors Cd_{1 − x} Mn _x GeAs₂ and Cd_{1 − x} Mn _x GeP₂ have been studied at high hydrostatic pressures, up to 7 GPa. The normal and anomalous Hall coefficients of the samples have been determined graphically from experimental data.     

Preparation and thermophysical properties of (NdxGd1?x)2Zr2O7 ceramics

Ceramic powders of (Nd _x Gd_1−x )₂Zr₂O₇ (x = 0, 0.1, 0.3, 0.5, 0.7, 0.9, 1.0) were synthesized by chemical-coprecipitation followed by calcination method, and were then pressureless-sintered at 1,600 °C for 10 h in air. Phase constituents and morphologies of the synthesized powders and sintered ceramics were identified by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). A high-temperature dilatometer and a laser-flash method were used to analyze the thermal expansion coefficient and thermal diffusion coefficient of different ceramics from room temperature up to 1,400 °C. Thermal conductivity was calculated from thermal diffusivity, density, and specific heat. (Nd _x Gd_1−x )₂Zr₂O₇ (0.1 ≤ x ≤ 1.0) ceramics are with a pyrochlore-type structure; however, pure Gd₂Zr₂O₇ exhibits a defective fluorite-type structure. The average linear thermal expansion coefficients of different (Nd _x Gd_1−x )₂Zr₂O₇ ceramics decrease with increasing the value of x from 0 to 1.0 in the temperature range of 25–1,400 °C. The thermal conductivities of (Nd _x Gd_1−x )₂Zr₂O₇ ceramics are located within the range of 1.33 to 2.04 W m⁻¹ K⁻¹ from room temperature to 1,400 °C.     

Magnetization Processes of (La0.7Pb0.3MnO3)1?x(SiO2)x Composites

The ceramic composites, (La_0.7Pb_0.3MnO₃)_1−x (SiO₂) _x , with diluted magnetic properties are prepared using solid-sate sintering route. Magnetization processes of (La_0.7Pb_0.3MnO₃)_1−x (SiO₂) _x composites are explored in this study. Ferromagnetism is gradually attenuated due to the magnetic dilution induced by the increase of SiO₂ content. Clearly, irreversible behavior is observed in the zero-field cooling and the field cooling (ZFC–FC) curves at a low field of 100 Oe. Saturation magnetization decreases as x increases while ferromagnetic transition temperature remains around 346 K for all composites. All the composites exhibit ferromagnetic hysteresis behavior which can be modeled by the law of the approach to saturation in the form M=M _S(1−a/H). The term a/H expresses the deviation of magnetization from saturation. The smaller factor a for La_0.7Pb_0.3MnO₃-rich samples results in sharper square curve which should be associated with the long-range spin order of ferromagnetic coupling.     

Magnetic order and evolution of the electronic state aroundx=0.12 in La2?xBaxCuO4 and La2?xSrxCuO4

Muon spin rotation ( ⁺SR) measurement provides clear evidence of the antiferromagnetic order of Cu moments below 35 K for La_2–x Ba _x CuO₄ and below 15 K for La_2–x Sr _x CuO₄ in the narrow range ofx where the high-T _c superconductivity (SC) is suppressed remarkably. The results suggest that the change of the electronic state coupled with the lattice instability is relevant to the local suppression of SC and freezing of spin fluctuations of the Cu moment.     

Superconducting Properties of Carbon and Zn Double-doped Mg1?xZnx(B1?xCx)2

A series of polycrystalline samples of Mg_1−x Zn _x (B_1−x C _x )₂ (x=0.00, 0.02, 0.04, 0.06, 0.08, and 0.10) were synthesized by a conventional solid-state reaction method under a background pressure about 10⁻³ Pa. Phase identification, crystal structure and superconducting transition temperature (T _c) were studied by means of X-ray diffraction (XRD) and resistivity measurements. The results indicated that the lattice parameters a and c show no clear trend in their changes with increasing doping level, and it turned out that the dopants had a marked effect on the crystal-lattice parameters and changed the crystal structure of the samples. The T _c for Mg_1−x Zn _x (B_1−x C _x )₂ decreased with C and Zn doping, but the rate of decrease was slower than single C-doped. We propose that the suppression of T _c by doping originates largely from the structural change.     

Electrical properties of Zn2(TiaSnb)1 ? xZrxO4 solid solutions

The electrical conductivity, band gap, dielectric permittivity, and molar polarizability of Zn₂(Ti _a Sn _b )_{1 − x} Zr _x O₄ solid solutions have been determined. All of the synthesized samples are dielectrics with semiconducting behavior of conductivity. The phase diagram of the Zn₂TiO₄-Zn₂SnO₄-Zn₂ZrO₄ system is presented.     

Growth and Accurate Characterization of Bi2Sr2?xLaxCuO6+δ Single Crystals

High-quality and various doped Bi₂Sr_2−x La _x CuO_6+δ (x=0–0.90) single crystals were obtained by floating-zone method. Analysis of the thermal behavior indicated an incongruent melt for all the doped compounds. The segregation coefficient of La related to Sr was estimated to be ∼1.02. Chemical compositions including the La doping in the crystals were accurately determined to study the effect of doping on the structural, chemical and superconducting property of the compounds. Raman spectra were performed to show the high-frequency modes 627 cm⁻¹ softened with increasing the doping level of La. Implications of the doping effect on crystals for understanding the superconductivity are discussed.     

Thermodynamic properties of (TeO2)0.95 ? n ? z(ZnO)z(Na2O)n(Bi2O3)0.05 glasses

The heat capacity (C _p ⁰) of the tellurite glasses