共查询到19条相似文献,搜索用时 312 毫秒
1.
2.
3.
4.
5.
6.
7.
第五节 电动机失控的预防措施电动机起动、停止及正反转切换过程中常发生操作失控,导致电动机及其拖动机械损坏,并造成人员伤亡.电动机失控的主要原因是接触器触头熔焊.另外触头熔焊还导致保护继电器失效.在桥式起重机造成的事故中失控占了很大的比重.比如某磷肥厂因触头熔焊无法紧急停车,造成两桥机相撞;某仓库因触头熔焊使保护失效,导致桥机越限坠落,机毁人亡.可见防止触头熔焊是一个十分重要的课题. 相似文献
8.
桥式起重机控制线路的改进设计 总被引:1,自引:0,他引:1
我国15/3t桥式起重机如果主接触器触头熔焊,就导致大车、小车、副钩的限位开关及其电机的过电流保护失效,如果主钩升降接触器触头熔焊,将导致主钩限位开关及其电机过电流保护失效,其结果可能造成重大的人身和设备事故。因此对于目前使用中的大部分桥式起重机,量重要的是改进或装设可靠的安全保护装置。虽然桥式起重机上装有刀开关,可以在接触器触头熔焊时切断工作电流,但是在紧急状况下,比如大车已经撞及轨道端部的止挡器面临出轨的危险, 相似文献
9.
10.
新型触头动熔焊数学模型的研究 总被引:2,自引:0,他引:2
在全面考虑了触头熔焊的决定性因素熔焊倾向和熔焊力的基础上 ,提出了一种新型的触头动熔焊数学模型。计算了单金属和银基复合触头材料的熔焊倾向和熔焊力 ,并与试验结果进行比较。结果表明 ,计算结果与试验结果吻合。 相似文献
11.
12.
13.
14.
Yoku Mukaiyama Isao Takagi Kunikazu Izumi Terukazu Sekiguchi Akio Kobayashi Toshio Sumikawa 《Electrical Engineering in Japan》1993,113(2):53-64
To explain contact failure phenomena and their development in the gas-insulated switchgear (GIS). tests were conducted by simulating abnormal current-carrying conditions using an actual 300-kV, 2000-A GIS. This paper describes the process observed. ranging from contact failures to ground faults, deteriorative phenomena and some detection methods for initial contact failure conditions. A summary of this study is as follows: (1) The contact resistances are greatly dependent on the materials and construction of contacts. (2) The relation between the initial contact resistance and the carried current resulting in arcing is derived with approximately constant Joule-heat generation. (3) Ground faults result from sagging of a shield melted by arcing or a combination of two causes: (i) scattering of molten metal caused by arcing; and (ii) sagging of a conductor caused by bolt melt down. (4) To detect initial contact failures, it is recommended to observe the contact resistance, the temperature rise on the tank surface, or the electrical partial discharges. 相似文献
15.
16.
磨损是造成电触点失效的主要原因之一。本文以镀金接触对为代表研究幅值对接触性能的影响。幅值对接触电阻和磨损的影响并非单调,存在最容易引起失效的临界微动幅值。磨损程度和磨损区域Au含量均在500μm时具有极小值,与接触电阻失效周期数的变化趋势相同。 相似文献
17.
18.
研究了手机中失效振子连接器镀金触点后发现,接触表面污染、连接器制造及表面镀层材料缺陷是造成电接触故障的主要原因。表面污染物来自于尘土颗粒和微动磨损,主要集中在印制电路板(PCB)一侧,其成分包括C、O、S i、A l、S、C l、Na、N i等多种元素。测试结果表明,污染表面多达86%的测量点的接触电阻超过设计标准。随后通过有限元建立振子连接器模型进行模态分析,结果表明连接器固有频率与其工作振动频率相接近,容易引起触点接触正压力的降低和磨损加速,降低了振子连接器的接触可靠性。 相似文献