Au-doped WO3-based sensor for NO2 detection at low operating temperature

Pure and Au-doped WO₃ powders for NO₂ gas detection were prepared by a colloidal chemical method, and characterized via X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). The NO₂ sensing properties of the sensors based on pure and Au-doped WO₃ powders were investigated by HW-30A gas sensing measurement. The results showed that the gas sensing properties of the doped WO₃ sensors were superior to those of the undoped one. Especially, the 1.0 wt% Au-doped WO₃ sensor possessed larger response, better selectivity, faster response/recovery and better longer term stability to NO₂ than the others at relatively low operating temperature (150 °C).     

Gas sensing properties of SnO2 nanowires on micro-heater

The SnO₂ nanowires (NWs) network gas sensors were fabricated on a micro-electrode and heater suspended in a cavity. The sensors showed selective detection to C₂H₅OH at a heater power during sensor operation as low as 30-40 mW. The gas response and response speed of the SnO₂ NWs sensor to 100 ppm C₂H₅OH were 4.6- and 4.7-fold greater, respectively, than those of the SnO₂ nanoparticles (NPs) sensor with the same electrode geometry. The reasons for these enhanced gas sensing characteristics are discussed in relation to the sensing materials and sensor structures.     

Solid-state potentiometric SO2 sensor combining NASICON with V2O5-doped TiO2 electrode

A compact tubular sensor based on NASICON (sodium super ionic conductor) and V₂O₅-doped TiO₂ sensing electrode was designed for the detection of SO₂. In order to reduce the size of the sensor, a thick-film of NASICON was formed on the outer surface of a small Al₂O₃ tube; furthermore, a thin layer of V₂O₅-doped TiO₂ with nanometer size was attached on the NASICON as a sensing electrode. This paper investigated the influence of V₂O₅ doping and sintering temperature on the characteristics of the sensor. The sensor attached with 5 wt% V₂O₅-doped TiO₂ sintered at 600 °C exhibited excellent sensing properties to 1–50 ppm SO₂ in air at 200–400 °C. The EMF value of the sensor was almost proportional to the logarithm of SO₂ concentration and the sensitivity (slope) was −78 mV/decade at 300 °C. It was also seen that the sensor showed a good selectivity to SO₂ against NO, NO₂, CH₄, CO, NH₃ and CO₂. Moreover, the sensor had speedy response kinetics to SO₂ too, the 90% response time to 50 ppm SO₂ was 10 s, and the recovery time was 35 s. On the basis of XPS analysis for the SO₂-adsorbed sensing electrode, a sensing mechanism involving the mixed potential at the sensing electrode was proposed.     

Enhanced H2S sensing characteristics of SnO2 nanowires functionalized with CuO

The CuO-functionalized SnO₂ nanowire (NW) sensors were fabricated by depositing a slurry containing SnO₂ NWs on a polydimethylsiloxane (PDMS)-guided substrate and subsequently dropping Cu nitrate aqueous solution. The CuO coating increased the gas responses to 20 ppm H₂S up to 74-fold. The R_a/R_g value of the CuO-doped SnO₂ NWs to 20 ppm H₂S was as high as 809 at 300 °C, while the cross-gas responses to 5 ppm NO₂, 100 ppm CO, 200 ppm C₂H₅OH, and 100 ppm C₃H₈ were negligibly low (1.5–4.0). Moreover, the 90% response times to H₂S were as short as 1–2 s at 300–400 °C. The selective detection of H₂S and enhancement of the gas response were attributed to the uniform distribution of the sensitizer (CuO) on the surface of the less agglomerated network of the SnO₂ NWs.     

A technique for monitoring SO2 in combustion exhausts: Use of a non-Nernstian sensing element in combination with an upstream catalytic filter

Detection of sulfur dioxide (SO₂) at high temperature (600–750 °C) in the presence of some interferents found in combustion exhausts (NO₂, NO, CO₂, CO, and hydrocarbon (C₃H₆)) is described. The detection scheme involves use of a catalytic filter in front of a non-Nernstian (mixed-potential) sensing element. The catalytic filter was a Ni:Cr powder bed operating at 850 °C, and the sensing elements were pairs of platinum (Pt) and oxide (Ba-promoted copper chromite ((Ba,Cu)_xCr_yO_z) or Sr-modified lanthanum ferrite (LSF)) electrodes on yttria-stabilized zirconia. The Ni:Cr powder bed was capable of reducing the sensing element response to NO₂, NO, CO, and C₃H₆, but the presence of NO₂ or NO (“NO_x”, at 100 ppm by volume) still interfered with the SO₂ response of the Pt–(Ba,Cu)_xCr_yO_z sensing element at 600 °C, causing approximately a 7 mV (20%) reduction in the response to 120 ppm SO₂ and a response equivalent to about 20 ppm SO₂ in the absence of SO₂. The Pt–LSF sensing element, operated at 750 °C, did not suffer from this NO_x interference but at the cost of a reduced SO₂ response magnitude (120 ppm SO₂ yielded 10 mV, in contrast to 30 mV for the Pt-(Ba,Cu)_xCr_yO_z sensing element). The powder bed and Pt–LSF sensing element were operated continuously over approximately 350 h, and the response to SO₂ drifted downward by about 7%, with most of this change occurring during the initial 100 h of operation.     

Tetrakis(alkylthio)-substituted lutetium bisphthalocyanines for sensing NO2 and O3

In this study, the nitrogen dioxide (NO₂) and ozone (O₃) sensing properties of a series bis[tetrakis(alkylthio) phthalocyaninato] lutetium(III) complexes [(C_nH_2n+1S)₄Pc]₂Lu(III) (n = 6, 10, 16) are investigated as a function of concentration in the temperature range between 25 °C and 150 °C. The concentration ranges were 1–10 ppm for NO₂, and 50 ppb–1 ppm for O₃. The response time and the sensor response to NO₂ are measured for approximately 1 min and 100% ppm⁻¹, respectively, for compound 1 at room temperature. At room temperature, all compounds are in the solid phase. The response time decreases to a few seconds with increasing operation temperature to 150 °C. At this temperature, all compounds are in the liquid crystal phase. The fastest response to oxidizing gases is observed at the liquid crystal phase of the Pcs. It has also been observed that the response time and the sensor response depend on the alkyl chain lengths of the Pcs. The doping effect of oxygen has been determined under high purity nitrogen N₂ flow, after exposure to dry air, at a different period of time and after annealing. It has been found that the conductivities of [(C_nH_2n+1S)₄Pc]₂Lu(III) thin films increased after exposure to dry air and the conduction mechanism also changed from ohmic behavior to space-charge-limited conduction.     

Ultrahigh ethanol response of SnO2 nanorods at low working temperature arising from La2O3 loading

The influences of La₂O₃ loading on the ethanol sensing properties of SnO₂ nanorods were investigated. An obvious enhancement of response was obtained. The response of 5 wt% La₂O₃ loaded SnO₂ nanorods was up to 213 for 100 ppm ethanol at low working temperature of 200 °C, while that of pure SnO₂ nanorods is 45.1. The improvement in response might be attributed to the presence of basic sites, which facilitated the dehydrogenation process. While the working temperature was increased to 300 °C, the sensor response decreased to 16 for 100 ppm ethanol. Additionally, the La₂O₃ loaded SnO₂ nanorods sensors showed good selectivity to ethanol over methane and hydrogen. Our results demonstrated that the La₂O₃ loaded SnO₂ nanorods were promising in fabricating high performance ethanol sensors which could work at low temperature.     

Electrostatic sprayed SnO2 and Cu-doped SnO2 films for H2S detection

This paper presents the ability of electrostatic sprayed tin oxide (SnO₂) and tin oxide doped with copper oxide (1, 2, and 4 at.% Cu) films to detect different pollutant gases, i.e., H₂S, SO₂, and NO₂. The influence of a copper oxide dopant on the SnO₂ morphology is studied using scanning electron microscopy (SEM) technique, which reveals a small decrease in the porosity and particle size when the amount of dopant is increased. The sensing properties of the SnO₂ films are greatly improved by doping, i.e., the Cu-doped SnO₂ films have large response to low concentration (10 ppm) of H₂S at low operating temperature (100 °C). Furthermore, no cross-sensitivity to 1 ppm NO₂ and 20 ppm SO₂ is observed. Among the studied films, the 1 at.% Cu-doped SnO₂ layer is the most sensitive in the detection of all the studied gases.     

Influence of Cs doping in spray deposited SnO2 thin films for LPG sensors

Detection of low concentrations of petroleum gas was achieved using transparent conducting SnO₂ thin films doped with 0–4 wt.% caesium (Cs), deposited by spray pyrolysis technique. The electrical resistance change of the films was evaluated in the presence of LPG upon doping with different concentrations of Cs at different working temperatures in the range 250–400 °C. The investigations showed that the tin oxide thin film doped with 2% Cs with a mean grain size of 18 nm at a deposition temperature of 325 °C showed the maximum sensor response (93.4%). At a deposition temperature of 285 °C, the film doped with 3% Cs with a mean grain size of 20 nm showed a high response of 90.0% consistently. The structural properties of Cs-doped SnO₂ were studied by means of X-ray diffraction (XRD); the preferential orientation of the thin films was found to be along the (3 0 1) directions. The crystallite sizes of the films determined from XRD are found to vary between 15 and 60 nm. The electrical investigations revealed that Cs-doped SnO₂ thin film conductivity in a petroleum gas ambience and subsequently the sensor response depended on the dopant concentration and the deposition temperature of the film. The sensors showed a rapid response at an operating temperature of 345 °C. The long-term stability of the sensors is also reported.     

Fabrication of N-type Fe2O3 and P-type LaFeO3 nanobelts by electrospinning and determination of gas-sensing properties

N-type Fe₂O₃ nanobelts and P-type LaFeO₃ nanobelts were prepared by electrospinning. The structure and micro-morphology of the materials were characterized by X-ray diffraction (XRD) and scanning of electron microscopy (SEM). The gas sensing properties of the materials were investigated. The results show that the optimum operating temperature of the gas sensors fabricated from Fe₂O₃ nanobelts is 285 °C, whereas that from LaFeO₃ nanobelts is 170 °C. Under optimum operating temperatures at 500 ppm ethanol, the response of the gas sensors based on these two materials is 4.9 and 8.9, respectively. The response of LaFeO₃-based gas sensors behaves linearly with the ethanol concentration at 10-200 ppm. Sensitivities to different gases were examined, and the results show that LaFeO₃ nanobelts exhibit good selectivity to ethanol, making them promising candidates as practical detectors of ethanol.     

Acoustic wave-based NO2 sensor: Ink-jet printed active layer

Microsphere-templated BaCO₃ films with well-defined area were deposited onto quartz crystal microbalances by thermal ink-jet printing, and the devices were characterized with respect to their microstructures and NO₂ sensing characteristics. Highly porous three-dimensional BaCO₃ frameworks with promising sensor characteristics were obtained. The printed thin films exhibited reversible frequency shifts following exposure to NO₂ and subsequent recovery under CO/CO₂ at 400 °C. The feasibility of controlled deposition of complex functional films in controlled patterns is discussed in the context of the direct-write features of ink-jet printing.     

Characterization of electrospun ZnO–SnO2 nanofibers for ethanol sensor

ZnO–SnO₂ nanofibers have been developed through in situ electrospinning technique and calcination. Poly(vinyl pyrrolidone) (PVP) is selected as fiber template. The composition of products can be controlled concisely by adjusting the compositions in their precursors. Under the optimized experimental conditions, the prepared product shows the desirable sensing characteristics towards ethanol gas at 300 °C, such as high response, excellent linearity in the range of 1–300 ppm, quick response time (5 s) and recovery time (6 s), good reproducibility, stability and selectivity.     

Enhanced H2S sensing characteristics of Pt doped SnO2 nanofibers sensors with micro heater

Gas sensors were designed and fabricated using oxide nanofibers as the sensing materials on micro platforms using micromachining technology. Pure and Pt doped SnO₂ nanofibers were prepared by electrospinning and their H₂S gas sensing characteristics were subsequently investigated. The sensing temperatures of 300 and 500 °C could be attained at the heater powers of 36 and 94 mW, respectively, and the sensors showed high and fast responses to H₂S. The responses of 0.08 wt% Pt doped SnO₂ nanofibers to 4-20 ppm H₂S, were 25.9-40.6 times higher than those of pure SnO₂ nanofibers. The gas sensing characteristics were discussed in relation to the catalytic promotion effect of Pt, nano-scale morphology of electrospun nanofibers, and sensor platform using micro heater.     

Nanostructured spinel ZnCo2O4 for the detection of LPG

Nanostrucutred spinel ZnCo₂O₄ (∼26-30 nm) was synthesized by calcining the mixed precursor (consisting of cobalt hydroxyl carbonate and zinc hydroxyl carbonate) in air at 600 °C for 5 h. The mixed precursor was prepared through a low cost and simple co-precipitation/digestion method. The transformation of the mixed precursor into nanostructured spinel ZnCo₂O₄ upon calcinations was confirmed by X-ray diffraction (XRD) measurement, thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and high resolution transmission electron microscopy (HRTEM). To demonstrate the potential applicability of ZnCo₂O₄ spinel in the fabrication of gas sensors, its LPG sensing characteristics were systematically investigated. The ZnCo₂O₄ spinel exhibited outstanding gas sensing characteristics such as, higher gas response (∼72-50 ppm LPG gas at 350 °C), response time (∼85-90 s), recovery time (∼75-80 s), excellent repeatability, good selectivity and relatively lower operating temperature (∼350 °C). The experimental results demonstrated that the nanostructured spinel ZnCo₂O₄ is a very promising material for the fabrication of LPG sensors with good sensing characteristics. Plausible LPG sensing mechanism is also discussed.     

In2O3 + xBaO (x = 0.5-5 at.%) - A novel material for trace level detection of NOx in the ambient

Indium oxide (In₂O₃) doped with 0.5-5 at.% of Ba was examined for their response towards trace levels of NO_x in the ambient. Crystallographic phase studies, electrical conductivity and sensor studies for NO_x with cross interference for hydrogen, petroleum gas (PG) and ammonia were carried out. Bulk compositions with x ≤ 1 at.% of Ba exhibited high response towards NO_x with extremely low cross interference for hydrogen, PG and ammonia, offering high selectivity. Thin films of 0.5 at.% Ba doped In₂O₃ were deposited using pulsed laser deposition technique using an excimer laser (KrF) operating at a wavelength of (λ) 248 nm with a fluence of ∼3 J/cm² and pulsed at 10 Hz. Thin film sensors exhibited better response towards 3 ppm NO_x quite reliably and reproducibly and offer the potential to develop NO_x sensors (Threshold limit value of NO₂ and NO is 3 and 25 ppm, respectively).     

Synthesis of ZnO nanorods and its application in NO2 sensors

One-dimensional (1D) ZnO nanorods with pencil-like shape and high aspect ratio were successfully synthesized using a cetyltrimethylammonium bromide (CTAB)-assisted hydrothermal process at 90 °C. The surface morphology and structure of nanocrystals were characterized by FE-SEM, XRD and XPS analysis. Experimental results show that the surfactant and base concentration play important roles in the formation and growth orientation of ZnO nanorods. The ZnO nanorods synthesized exhibits high response and selectivity to NO₂, the highest response to 40 ppm NO₂ reached 206 and the selectivity with respect to CO and CH₄ at same concentration reached 10.3 and 30 times, respectively. The effects of synthesis method, surfactant and calcination condition on sensing properties were systematically investigated. The results indicate that the CTAB-assisted low temperature hydrothermal process is a potentially facile method for synthesis of 1D ZnO nanorods and excellent potential candidates as gas sensing materials.     

The effect of La2CuO4 sensing electrode thickness on a potentiometric NOx sensor response

In order to further understand the different contributions to NO_x sensing mechanism as well as the importance of electrode geometry, solid state potentiometric sensors with varying La₂CuO₄ sensing electrode thicknesses were studied. These sensors (with a Pt counter electrode) showed a dependence of NO₂ sensitivity which decreased with increasing thickness in the temperature range of 550-650 °C. They also showed NO sensitivity that was independent of thickness at 400 °C and 600 °C, but varied at temperatures between. This behavior was attributed to multiple mechanistic contributions explained by Differential Electrode Equilibria.     

Highly sensitive and selective LPG sensor based on α-Fe2O3 nanorods

The α-Fe₂O₃ nanorods were successfully synthesized without any templates by calcining the α-FeOOH precursor in air at 300 °C for 2 h and their LPG sensing characteristics were investigated. The α-FeOOH precursor was prepared through a simple and low cost wet chemical route at low temperature (40 °C) using FeSO₄·7H₂O and CH₃COONa as starting materials. The formation of α-FeOOH precursor and its topotactic transformation to α-Fe₂O₃ upon calcination was confirmed by X-ray diffraction measurement (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) analysis. The α-Fe₂O₃ nanorods exhibited outstanding gas sensing characteristics such as, higher gas response (∼1746-50 ppm LPG at 300 °C), extremely rapid response (∼3-4 s), relatively slow recovery (∼8-9 min), excellent repeatability, good selectivity and lower operating temperature (∼300 °C). Furthermore, the α-Fe₂O₃ nanorods are able to detect up to 5 ppm for LPG with reasonable response (∼15) at the operating temperature of 300 °C and they can be reliably used to monitor the concentration of LPG over the range (5-60 ppm). The experimental results clearly demonstrate the potential of using the α-Fe₂O₃ nanorods as sensing material in the fabrication of LPG sensors. Plausible LP G sensing mechanism of the α-Fe₂O₃ nanorods is also discussed.     

Formaldehyde sensing properties of electrospun NiO-doped SnO2 nanofibers

Formaldehyde is a kind of hazardous gases dangerous to human health. Hence, gas sensor is an essential device to monitor formaldehyde in air, especially in indoor ambient. Semiconductor metal oxides are studied as gas-sensing material to detect most of key gases for decade years. For the purpose of actual application and meeting a variety of conditions, diverse additives added into host material are expected to improve the performance of gas sensors. The formaldehyde gas-sensing characteristics of undoped and NiO-doped SnO₂ (NSO) nanofibers synthesized via a simple electrospinning method were investigated in this study. It is noticed that the addition of NiO causes the distortion at the surface of SnO₂ nanofibers, which is responsible to adjust activation energy, grain sizes and chemical states of host material. The sensors fabricated from NSO nanofibers exhibited good formaldehyde sensing properties at operating temperature 200 °C, and the minimum-detection-limit was down to 0.08 ppm. The response time and recovery time of the sensors were about 50 s and 80 s to 10 ppm formaldehyde, respectively. The sensor shows a good long-term stability in 90 days. The simple preparation and excellent properties significantly advance the viability of electrospun nanofibers as gas sensing materials. The sensing mechanisms of NSO nanofibers to formaldehyde were discussed. The results indicated that NSO nanofibers could be used as a candidate to fabricate formaldehyde sensors in practice.     

Glucose-mediated hydrothermal synthesis and gas sensing characteristics of WO3 hollow microspheres

Tungsten-coated carbon microspheres were prepared by one-pot hydrothermal reaction of an aqueous solution containing glucose and sodium tungstate. The spheres were converted into WO₃ hollow microspheres by the decomposition of their core carbon. The [glucose]/[sodium tungstate] ratio of the stock solution determined not only the morphology of the precursors but also the phase of the powders after calcination. The WO₃ hollow microspheres showed a higher gas response and more selective detection of 0.5–2.5 ppm NO₂ than WO₃ solid and nano-porous microspheres did. The enhanced NO₂ sensing characteristics are explained in relation to the surface area, pore volume, and hollow morphology.