Effect of maleic‐anhydride‐grafted polypropylene as a compatibilizer on the properties of polypropylene/(modified carbon black) composites

Maleic‐anhydride‐grafted polypropylene (PP‐g‐MAH) was added, as a compatibilizer, to polypropylene (PP) composites filled with a hindered phenol and modified carbon black (CB). The interaction between the modified CB and PP‐g‐MAH, as proved by Fourier transform infrared spectroscopy, had a beneficial effect on the mechanical properties of the PP/(modified CB) composites and prevented the sharp decrease of the mechanical properties of these composites at higher filler concentration. The storage modulus of PP/(modified CB) was increased significantly by the incorporation of PP‐g‐MAH, especially when the temperature was lower than 0°C. When the content of PP‐g‐MAH was 5 wt% and the loading of the modified CB was 2 wt%, the best tensile strength was obtained. The system showed the best flexural strength and impact strength when the loading of the modified CB was 1 wt%. J. VINYL ADDIT. TECHNOL., 2011. © 2011 Society of Plastics Engineers     

Effect of maleic anhydride/vinyltrimethoxysilane‐co‐grafting polypropylene on the properties of wood‐flour/polypropylene composites by electron‐beam preirradiation

The electron‐beam preirradiation and reactive extrusion technologies were used to prepare maleic anhydride (MAH)/vinyltrimethoxysilane (VTMS)‐co‐grafting polypropylene (PP) as a high‐performance compatibilizer for wood‐flour/PP composites. The grafting content, chemical structure, and crystallization behavior of the compatibilizers were characterized through Fourier transform infrared spectroscopy, differential scanning calorimetry, and an extraction method. The effects of the compatibilizers on the mechanical properties, water absorption, morphological structure, and torque rheological behavior of the composites were investigated comparatively. The experimental results demonstrate that MAH/VTMS‐g‐PP markedly enhanced the mechanical properties of the composites. Compared with MAH‐g‐PP and VTMS‐g‐PP, MAH/VTMS‐g‐PP clearly showed synergistic effects on the increasing mechanical properties, water absorption, and compatibility of the composites. Scanning electron microscopy further confirmed that the adhesion and dispersion of wood flours in the composites were effectively improved by MAH/VTMS‐g‐PP. These results were also proven by the best water resistance of the wood‐flour/PP composites with MAH/VTMS‐g‐PP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of clay contents on the dynamic mechanical and rheological properties of polypropylene/MAH‐g‐POE/clay composites

A series of polypropylene/maleic anhydride grafted polypropylene octane elastomer (MAH‐g‐POE)/clay (PPMC) nanocomposites were prepared with a novel compatilizer MAH‐g‐POE and different contents of octadecyl amine modified montmorillonite, and the effects of clay contents on the dynamic mechanical and rheological properties of these PPMC composites were investigated. With clay content increasing, the characteristic X‐ray diffraction peak changed from one to two with intensity decreasing, indicating the decreasing concentration of the intercalated clay layers. The gradual decrease of crystallization temperature of PPMC composites with the increase of clay loading should be attributed to the preferred intercalation of MAH‐g‐POE molecules into clay interlayer during blending, which is also reflected by scanning electron microscopy observations. By evaluating the activation energy for the glass transition process of MAH‐g‐POE and polypropylene (PP) in the PPMC composites, it is found that clay intercalation could cause the restriction effect on the glass transition of both MAH‐g‐POE and PP, and this restriction effect appears stronger for PP and attained the highest degree at 5 wt % clay loading. The melt elasticity of PP could be improved apparently by the addition of MAH‐g‐POE, and 5 wt % clay loading is enough for further enhancing the elastic proportion of PP. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Polypropylene–intumescent flame‐retardant composites based on meleated polypropylene as a coupling agent

The phosphoric acid‐pentaerythritol‐melamine copolymer, which is composed of three main components of intumescent flame retardant (IFR) and has optimal intumescent degree, was selected as IFR. The influence of meleated polypropylene (PP‐g‐MAH) on the properties and compatibility of IFR polypropylene (PP) composites were studied. The results obtained from mechanical tests, rheological behavior of composites, and scanning electron microscope showed that PP‐g‐MAH was a true coupling agent for IFR/PP blends and did not change the necessary flame retardancy. The cocrystallization between bulk PP and PP segments of PP‐g‐MAH was also proven by WAXD analysis. Flow test showed that the flow behaviors of composites in the melt are those of a pseudoplastic and it is very small for PP‐g‐MAH affecting rheological behavior of the PP/IFR composite. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 257–262, 2002     

Dynamically cured polypropylene/Novolac blends compatibilized with maleic anhydride‐g‐polypropylene

In this article, the dynamic vulcanization process was applied to polypropylene (PP)/Novolac blends compatibilized with maleic anhydride‐grafted PP (MAH‐g‐PP). The influences of dynamic cure, content of MAH‐g‐PP, Novolac, and curing agent on mechanical properties of the PP/Novolac blends were investigated. The results showed that the dynamically cured PP/MAH‐g‐PP/Novolac blend had the best mechanical properties among all PP/Novolac blends. The dynamic cure of Novolac improved the modulus and stiffness of the PP/Novolac blends. The addition of MAH‐g‐PP into dynamically cured PP/Novolac blend further enhanced the mechanical properties. With increasing Novolac content, tensile strength, flexural modulus, and flexural strength increased significantly, while the elongation at break dramatically deceased. Those blends with hexamethylenetetramine (HMTA) as a curing agent had good mechanical properties at HMTA content of 10 wt %. Scanning electron microscopy (SEM) analysis showed that dynamically cured PP/MAH‐g‐PP/Novolac blends had finer domains than the PP/MAH‐g‐PP/Novolac blends. Thermogravimetric analysis (TGA) results indicated that the incorporation of Novolac into PP could improve the thermal stability of PP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Peroxide‐catalyzed swell grafting of maleic anhydride onto polypropylene

A new grafting method was developed to incorporate maleic anhydride directly onto solid‐state polypropylene powders. Maleic anhydride grafts altered the nonpolar characteristics of polypropylene so that much better mixing was achieved in blends and composites of polypropylene with many other polymers and fillers. Maleic anhydride was grafted onto polypropylene by the peroxide‐catalyzed swell grafting method, with a maximum extent of grafting of 4.60%. Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy, tensile testing, and impact testing were used to characterize the isotactic polypropylene (iPP), maleic anhydride grafted polypropylene (MAH‐g‐iPP), and (isotactic polypropylene)/(calcium carbonate) composites (iPP/CaCO₃). The crystallinity and heat of fusion of the MAH‐g‐iPP decreased as the extent of grafting increased. The mechanical properties of the CaCO₃ filled polypropylene were improved by adding MAH‐g‐iPP as a compatibilizing agent. The dispersion of the fillers in the polymer matrix and the adhesion between the CaCO₃ particles and the polymer matrix were improved by adding the compatibilizer.     

Compatibilization of polypropylene/Poly(acrylonitrile‐butadiene‐styrene) blends by polypropylene‐graft‐cardanol

The polypropylene‐graft‐cardanol (PP‐g‐cardanol) was prepared by reactive extrusion with polypropylene (PP) and natural renewable cardanol which could increase the interfacial energy of PP and inhibit the degradation of PP during the process of reactive extrusion and usage. In this article, PP‐g‐cardanol and polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) were used as compatibilizers of the polypropylene (PP)/poly(acrylonitrile‐butadiene‐styrene) (ABS) blends. PP/ABS (70/30, wt %) blends with PP‐g‐cardanol and PP‐g‐MAH were prepared by a corotating twin‐screw extruder. From the results of morphological studies, the droplet size of ABS was minimized to 1.93 and 2.01 μm when the content of PP‐g‐cardanol and PP‐g‐MAH up to 5 and 7 phr, respectively. The results of mechanical testing showed that the tensile strength, impact strength and flexural strength of PP/ABS (70/30) blends increase with the increasing of PP‐g‐cardanol content up to 5 phr. The complex viscosity of PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol showed the highest value. Moreover, the change of impact strength and tensile strength of PP/ABS (70/30) blends were investigated by accelerated degradation testing. After 4 accelerated degradation cycles, the impact strength of the PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol decrease less than 6%, but PP/ABS (70/30) blends with 5 phr PP‐g‐MAH and without compatibilizer decrease as much as 12% and 32%, respectively. The tensile strength of PP/ABS (70/30) blends has a similar tendency to that of impact strength. The above results indicated that PP‐g‐cardanol could be used as an impact modifier and a good compatibilizer, which also exhibited better stability performance during accelerated degradation testing. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41315.     

Study of dynamically cured PP/MAH‐g‐PP/talc/epoxy composites

In the present study, an epoxy resin was dynamically cured in a polypropylene (PP)/maleic anhydride–grafted PP (MAH‐g‐PP)/talc matrix to prepare dynamically cured PP/MAH‐g‐PP/talc/epoxy composites. An increase in the torque at equilibrium showed that epoxy resin in the PP/MAH‐g‐PP/talc composites had been cured by 2‐ethylene‐4‐methane‐imidazole. Scanning electron microscopy analysis showed that MAH‐g‐PP and an epoxy resin had effectively increased the interaction adhesion between PP and the talc in the PP/talc composites. Dynamic curing of the epoxy resin further increased the interaction adhesion. The dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had higher crystallization peaks than did the PP/talc composites. Thermogravimetric analysis showed that the addition of MAH‐g‐PP and the epoxy resin into the PP/talc composites caused an obvious improvement in the thermal stability. The dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had the best thermal stability of all the PP/talc composites. The PP/MAH‐g‐PP/talc/epoxy composites had better mechanical properties than did the PP/MAH‐g‐PP/talc composites, and the dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had the best mechanical properties of all the PP/talc composites, which can be attributed to the better interaction adhesion between the PP and the talc. The suitable content of epoxy resin in the composites was about 5 wt %. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Effect of silane‐grafted polypropylene on the mechanical properties and crystallization behavior of talc/polypropylene composites

Talc‐filled polypropylene (PP) composites coupled with silane‐grafted polypropylene (PP‐g‐Si) were prepared. Effect of PP‐g‐Si on the mechanical properties, crystallization, and melting behavior of PP composites was investigated. Compared with the uncoupled composites, the mechanical properties of Talc/PP composites coupled with a small amount of PP‐g‐Si were increased to some extent. Meanwhile, PP‐g‐Si can promote crystallization rate and increase crystallization temperature of PP in the composites. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2974–2977, 2000     

Interfacial modification of single‐walled carbon nanotubes for high‐loading‐reinforced polypropylene composites

In this article, we present a strategy for fabricating polypropylene (PP)/polypropylene‐regrafted single‐walled carbon nanotube (PP‐re‐g‐SWNT) composites with a high loading of single‐walled carbon nanotubes (SWNTs; 20 wt %). The PP‐re‐g‐SWNTs were characterized by X‐ray photoelectron, Fourier transform infrared spectroscopy, transmission electron microscopy, and thermogravimetric analysis (TGA). The PP‐re‐g‐SWNTs showed excellent interfacial adhesion and dispersion. Furthermore, PP molecules, about 72 wt % by mass, were homogeneously bonded onto the surface of the SWNTs according to TGA. In this hybrid nanocomposite system, the PP‐re‐g‐SWNTs were covalently integrated into the PP matrix and became part of the conjugated network structure (as evidenced by differential scanning calorimetry and dynamic mechanical analysis) rather than just a separate component. Accordingly, the PP/PP‐re‐g‐SWNT composites presented obvious improvements in mechanical properties and conductivity (from 10^?10 to 10^?2). Most importantly, the tensile and flexural strength of the PP/PP‐re‐g‐SWNT composites did not exhibit an obvious downturn with the addition of 20 wt % SWNTs; this was contrary to documented results. We believe that these new observations were due to the novel structure of the PP‐re‐g‐SWNTs. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39817.     

Synthesis of polypropylene‐graft‐maleic anhydride compatibilizer and evaluation of nylon 6/polypropylene blend properties

Polymer blends based on polyolefins are of a great interest owing to their broad spectrum of properties and practical applications. However, because of poor compatibilities of components, most of these systems generally exhibit high interfacial tension, a low degree of dispersion and poor mechanical properties. It is generally accepted that polypropylene (PP) and nylon 6 (N6) are not compatible and that their blending results in poor materials. The compatibility can be improved by the addition of a compatibilizer, and in this study PP was functionalized by maleic anhydride (MAH) in the presence of an optimized amount of dicumyl peroxide (DCP). The reaction was carried out in the molten state using an internal mixer. Then, once the compatibilizer polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) was prepared, it was added at various concentrations (2.5–10 wt%) to 30/70 glass fibre reinforced N6 (GFRN6) PP, and the mechanical properties were evaluated. It was found that the incorporation of the compatibilizer enhanced the tensile properties (tensile strength and modulus) as well as the Izod impact properties of the notched samples. This was attributed to better interfacial adhesion as evidenced by scanning electron microscopy (SEM). The optimum in these properties was achieved at a critical PP‐g‐MAH concentration. Copyright © 2005 Society of Chemical Industry     

Crystallization behavior of carbon black‐filled polypropylene and polypropylene/epoxy composites

The crystallization behavior of polypropylene (PP)/carbon black (CB) and PP/epoxy/CB composites was studied with differential scanning calorimetry (DSC). The effects of compatibilizer MAH‐g‐PP and dynamic cure on the crystallization behavior are investigated. The nonisothermal crystallization parameters analysis showed that CB particles in the PP/CB composites and the dispersed epoxy particles in the PP/epoxy composites could act as nucleating agents, accelerating the crystallization of the composites. Morphological studies indicated that the incorporation of CB into PP/epoxy resulted in its preferential localization in the epoxy resin phase, changing the spherical epoxy particles into elongated structure, and thus reduced the nucleation effect of epoxy particles. Addition of MAH‐g‐PP significantly decreased the average diameter of epoxy particles in the PP/epoxy and PP/epoxy/CB composites, promoting the crystallization of PP more effectively. The isothermal crystallization kinetics and thermodynamics of the PP/CB and PP/epoxy/CB composites were studied with the Avrami equation and Hoffman theory, respectively. The Avrami exponent and the crystallization rate of the PP/CB composites were higher than those of PP, and the free energy of chain folding for PP crystallization decreased with increasing CB content. Addition of MAH‐g‐PP into the PP/epoxy and PP/epoxy/CB composites increased the crystallization rate of the composites and decreased the chain folding energy significantly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 104–118, 2006     

Enhanced foamability of isotactic polypropylene composites by polypropylene‐graft‐carbon nanotube

In this article, utilizing a nucleophilic substitution reaction between epoxy group in polypropylene‐graft‐glycidyl methacrylate (PP‐g‐GMA) and carboxyl groups in oxidized carbon nanotubes (O‐CNTs), PP‐g‐CNT was fabricated for reinforcing the interfacial adhesion between CNTs and polypropylene (PP) matrix, favoring the enhancement of melt strength and elastic modulus, i.e., enhancing the foaming ability of PP composites. Cellular structure and thermo‐mechanical properties of PP foams were characterized by scanning electron microscopy and dynamic mechanical analysis, respectively. The average cell diameter of PP foams decreased from 289.2 (PP‐g‐GMA) to 96.7 μm (PP‐g‐CNT foams with 2.0 wt % O‐CNT) and the distribution of cell size also became more uniform. The storage modulus of PP‐g‐CNT foams increased by nearly 62.5% at ?40°C, compared with that of PP‐g‐GMA foams. This work also provided a new procedure for improving the foam ability and thermo‐mechanical property of PP composites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 961‐968, 2013     

Effect of maleic anhydride grafted polypropylene on the mechanical and morphological properties of chemically modified short‐pineapple‐leaf‐fiber‐reinforced polypropylene composites

With the rising cost of petroleum‐based fibers, the utilization of plant fibers in the manufacture of polymer–matrix composites is gaining importance worldwide. The scope of this study was to examine the perspective of the use of pineapple leaf fibers (PALFs) as reinforcements for polypropylene (PP). These fibers are environmentally friendly, low‐cost byproducts of pineapple cultivation and are readily available in the northeastern region of India. Here, both untreated and treated pineapple fibers were used. Maleic anhydride grafted polypropylene (MA‐g‐PP) was used as a compatibilizing agent. The polymer matrix of PP was used to prepare composite specimens with different volume fractions (5–20%) of fibers by the addition of 5% of MA‐g‐PP. These specimens were tested for their mechanical properties, and additional assessments were made via observations by scanning electron microscopy, thermogravimetric analysis, and IR spectroscopy. Increase in the impact behavior, flexural properties, and tensile moduli of the composites were noticed, and these were more appreciable in the treated fibers mixed with MA‐g‐PP. PALF in 10 vol % in PP mixed with MA‐g‐PP was the optimum and recommended composition, where the flexural properties were the maximum. The impact strength and the tensile modulus were also considerably high. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Extrusion foaming behavior of a polypropylene/nanoclay microcellular foam

With maleic anhydride grafted polypropylene (PP‐g‐MAH) as a compatibilizer, composites of block‐copolymerized polypropylene (B‐PP)/nanoclay were prepared. The effects of the PP‐g‐MAH and nanoclay content on the crystallization and rheological properties of B‐PP were investigated. The microcellular foaming behavior of the B‐PP/nanoclay composite material was studied with a single‐screw extruder foaming system with supercritical (SC) carbon dioxide (CO₂) as the foaming agent. The experimental results show that the addition of nanoclay and PP‐g‐MAH decreased the melt strength and complex viscosity of B‐PP. When 3 wt % SC CO₂ was injected as the foaming agent for the extrusion foaming process, the introduction of nanoclay and PP‐g‐MAH significantly increased the expansion ratio of the obtained foamed samples as compared with that of the pure B‐PP matrix, lowered the die pressure, and increased the cell population density of the foamed samples to some extent. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44094.     

Crystallization behavior of PP/PP‐g‐MAH/GFR PA66 blends: Establishment of their continuous‐cooling‐transformation of relative crystallinity diagrams

Polypropylene/polypropylene‐grafted‐maleic anhydride/glass fiber reinforced polyamide 66 (PP/PP‐g‐MAH/GFR PA 66) blends‐composites with and without the addition of polypropylene‐grafted‐maleic anhydride (PP‐g‐MAH) were prepared in a twin screw extruder. The effect of the compatibilizer on the thermal properties and crystallization behavior was determined using differential scanning calorimetry analysis. The hold time was set to be equal to 5 min at 290°C. These conditions are necessary to eliminate the thermomechanical history in the molten state. The crystallization under nonisothermal conditions and the plot of Continuous‐Cooling‐Transformation of relative crystallinity diagrams of both PP and PA 66 components proves that PP is significantly affected by the presence of PP‐g‐MAH. From the results it is found that an abrupt change is observed at 2.5 wt % of PP‐g‐MAH as a compatibilizer and then levels off. In these blends, concurrent crystallization behavior was not observed for GFR PA66. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1620–1626, 2007     

Polypropylene‐organoclay nanocomposite: Preparation,microstructure, and mechanical properties

A series of polypropylene (PP) nanocomposites containing 2, 4, and 6 wt % of an organophilic montmorillonite clay was prepared via direct melt mixing in the presence of maleic anhydride grafted polypropylene (PP‐g‐MAH) as compatibilizing agent. Microstructure characterization was performed by X‐ray diffraction analysis. Nanocomposites exhibited a 15 and 22% enhancement in tensile modulus and impact strength, respectively. The heat deflection temperature of PP nanocomposites was 36°C greater than for pure PP. Thermal and mechanical properties of nanocomposites were compared to properties of traditional PP‐talc and PP‐glass fiber composites. The results showed that the properties of nanocomposites improved compared to ordinary polypropylene composites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Investigation on β‐polypropylene/PP‐g‐MAH/ surface‐treated calcium carbonate composites

β‐Polypropylene composites containing calcium carbonate treated by titanate coupling agent (T‐CaCO₃) and maleic anhydride grafted PP (PP‐g‐MAH) were prepared by melt compounding. The crystallization, morphology and mechanical properties of the composites were investigated by means of differential scanning calorimetry, wide‐angle X‐ray diffraction, polarized light microscopy, scanning electron microscopy and mechanical tests. It is found that both T‐CaCO₃ and NT‐C are able to induce the formation of β‐phase, and NT‐C greatly increases the β content and decreases the spherulitic size of PP. PP‐g‐MAH facilitates the formation of β‐form PP and improves the compatibility between T‐CaCO₃ and PP. Izod notched impact strength of β‐PP/T‐CaCO₃ composite is higher than that of PP/T‐CaCO₃ composite, indicating the synergistic toughening effect of T‐CaCO₃ and β‐PP. Incorporation of PP‐g‐MAH into β‐PP/T‐CaCO₃ composite further increases the content of β‐crystal PP and improves the impact strength and tensile strength when T‐CaCO₃ concentration is below 5 wt%. The nonisothermal crystallization kinetics of β‐PP composites is well described by Jeziorny's and Mo's methods. It is found that NT‐C and T‐CaCO₃ accelerate the crystallization rate of PP but the influence of PP‐g‐MAH on crystallization rate of β‐PP composite is marginal. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Melting and crystallization behaviors,morphology, and mechanical properties of β‐polypropylene/polypropylene‐graft‐maleic anhydride/calcium sulfate whisker composites

The melting and crystallization behaviors, morphology, and mechanical properties of polypropylene (PP)/surface‐treated calcium sulfate (CaSO₄) whisker (T‐CSW), β‐PP/T‐CSW, and β‐PP/polypropylene‐graft‐maleic anhydride (PP‐g‐MAH)/T‐CSW composites had been investigated via differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), polarized light microscopy (PLM), scanning electron microscopy (SEM), and mechanical tests. We found that T‐CSW was an α‐nucleating agent and increased the crystallization temperatures of PP, but PP‐g‐MAH and high loadings of T‐CSW had weakly negative effects on the crystallization rates of PP. The T‐CSW restrained the formation of β‐spherulites, and the spherulitic size decreased in the composites. PP‐g‐MAH improved the compatibility and adhesion between T‐CSW and the matrix. The notched impact strength was improved, and the tensile strength was enhanced at low levels of T‐CSW, while the flexural modulus was weakened for β‐PP/T‐CSW and β‐PP/PP‐g‐MAH/T‐CSW composites versus PP/T‐CSW composites. POLYM. COMPOS., 37:2121–2132, 2016. © 2015 Society of Plastics Engineers     

Effect of grafting yield and molecular weight of m‐TMI‐grafted‐PP on the mechanical properties of wood fiber filled polypropylene composites

m‐Isopropenyl‐α, α‐dimethylbenzyl isocyanate (m‐TMI) was grafted on isotactic polypropylene (PP) using di‐cumyl peroxide as a reaction initiator under varying reaction conditions to yield m‐TMI‐g‐PP coupling agent with four sets of grafting yield and molecular weight. Grafting yield of the synthesized m‐TMI‐g‐PP were 1.80%, 2.01%, 9.05%, and 8.86% and molecular weight of the corresponding grafted polymer were 129,225; [Correction made here after initial online publication.] 187,240; 124,130; and 180,838, respectively. Rubberwood flour reinforced polypropylene composites were prepared using these coupling agents and tested for mechanical properties. m‐TMI‐g‐PP coupling agent with 9.09% grafting and 124230 M_w was found to give the highest tensile and flexural strengths. Flexural modulus of the coupled composites was higher than uncoupled composites. Interfacial region of the composites characterized by scanning electron microscope (SEM) suggest effective wetting of fiber by PP in the case of coupled composites. The effect of fiber loading on composites indicates continuous increment in tensile and flexural strengths in coupled composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44196.