凹槽-襟翼对翼型动态失速特性影响研究

风力机复杂运行环境使叶片常处于失速环境,导致翼型升力骤降,严重影响风力机气动性能.为改善翼型流动分离,延缓失速,对凹槽-襟翼对翼型动态失速特性作用效果开展研究,并利用计算流体力学方法分析不同折合频率与翼型厚度时凹槽-襟翼对翼型气动性能的影响.结果表明:俯仰振荡过程中,凹槽-襟翼可有效提升翼型吸力面流速,降低失速攻角下逆...     

振动膜片的流动控制机理研究

采用计算流体力学方法,研究了主流风速为10 m/s,翼型弦长雷诺数为1.2×10~5条件下振动膜片对NACA0012翼型在18°攻角深失速下流动分离的影响。研究表明:振动膜片能明显提高翼型升力系数、降低阻力系数、改善流场状况;当无量纲频率处在1~1.5范围内时,翼型升阻比可大幅提升,最大可提高75.7%;无量纲振幅对翼型升阻比的影响也很显著,相对于原型存在一个最佳的振幅使得翼型升阻比能获得最大提升;不同振幅下,最佳升阻比对应的无量纲频率随振幅增大而减小。     

垂直轴风力机改进翼型气动及功率特性研究

为提高垂直轴风力机的风能利用率,基于CFD数值模拟技术,分析了常用典型垂直轴风力机翼型的气动及功率特性,并以NACA0012翼型为基础对其进行改进。对比改进前后翼型表明,增大翼型厚度可降低升阻比,增大翼型弯度可增强其失速特性;厚尾缘翼型、升阻互补型翼型可分别降低翼型失速性能、增加启动力矩,其中厚尾缘翼型的H型垂直轴风力机的功率系数较大,可提高风能利用率,为翼型优化设计提供了新思路。     

Trailing edge serrations effects on the aerodynamic performance of a NACA 643418

A study of the aerodynamic performance of a NACA 64₃418 airfoil with trailing edge serrations is presented. For the prediction of the changes in lift due to the serration installation, an empirical law is derived that can be extended to typical cambered airfoils for wind turbine applications. The law is deduced from 2D and 3D Reynolds‐averaged Navier–Stokes simulations (RANS) of the flow over the airfoil. Lift and drag together with the changes in the wake flow due to the presence of the serrated edges are investigated. An additional study of the sensitivity of the results at Re_c = 3·10⁶ with respect to the turbulence modeling is carried out by using three different RANS models: Spalart–Allmaras, k‐omega SST, and Transition SST. Results show that the changes in lift due to trailing‐edge extensions are approximated by the effect of a split plate with reduced length.     

Effects of leading edge erosion on wind turbine blade performance

This paper presents results of a study to investigate the effect of leading edge erosion on the aerodynamic performance of a wind turbine airfoil. The tests were conducted on the DU 96‐W‐180 wind turbine airfoil at three Reynolds numbers between 1 million and 1.85 million, and angles of attack spanning the nominal low drag range of the airfoil. The airfoil was tested with simulated leading edge erosion by varying both the type and severity of the erosion to investigate the loss in performance due to an eroded leading edge. Tests were also run with simulated bugs on the airfoil to assess the impact of insect accretion on airfoil performance. The objective was to develop a baseline understanding of the aerodynamic effects of varying levels of leading edge erosion and to quantify their relative impact on airfoil performance. Results show that leading edge erosion can produce substantial airfoil performance degradation, yielding a large increase in drag coupled with a significant loss in lift near the upper corner of the drag polar, which is key to maximizing wind turbine energy production. Copyright © 2013 John Wiley & Sons, Ltd.     

直接测力俯仰振荡翼型动态气动性能研究

在西北工业大学NF-3低速风洞二元实验段开展翼型俯仰振荡运动动态气动性能深入研究。实验模型为展向三段式测力模型,测力仅在模型中段进行以减小风洞侧壁干扰的影响。实验中采集模型的转动瞬态迎角、计算模型中段的惯性力和惯性力矩、并从天平采集数据中扣除以修正模型惯性对结果的影响。结果表明,迎角超过正向或负向静态失速迎角是升力系数和俯仰力矩系数产生大的迟滞环的必要条件。随着振荡缩减频率增大,动态失速会推迟,升力系数迟滞环增大,阻力系数增大,最大迎角附近的俯仰力矩系数减小。在迎角小于静态失速迎角或超过不大的迎角范围,随着缩减频率的增大,翼型振荡运动俯仰力矩系数上行时减小,下行时增大。随着振荡振幅的增大,翼型振荡运动动态升力系数和俯仰力矩系数的迟滞环增大。随着平均迎角的增大,翼型迎角更多地进入正向失速区,升力系数迟滞环增大,俯仰力矩系数最小值变小。雷诺数对升力系数、阻力系数和俯仰力矩系数迟滞环无明显影响;但是,在翼型模型下行过程,随着雷诺数的增大,升力恢复提前,同时迟滞环随雷诺数增大而减小。     

尾缘襟翼对风力机翼型气动特性影响研究

尾缘襟翼(TEF)因其对翼型气动特性的调控能力,被认为是降低叶片疲劳和局部载荷最具可行性的气动控制部件。对TEF进行建模,采用Xfoil和CFD软件分析了TEF对翼型气动特性的影响及其机理,并从叶素理论角度对变化来流下TEF的减载效果进行了验证,结果表明:TEF位于不同摆角时翼型升阻力系数均有不同程度的变化,TEF可有效实现对翼型气动特性的主动控制;TEF摆动改变了翼型表面的静压分布和流动状态,进而对翼型升阻力和失速攻角产生影响;TEF可快速有效降低风速突然增加后的叶素受力,进而控制并减小叶片载荷。     

Dynamic stall control via adaptive blowing

An aerodynamic load control concept termed “adaptive blowing” was successfully tested on a NACA 0018 airfoil model at Reynolds numbers ranging from 1.5·10⁵ to 5·10⁵. The global objective was to eliminate lift oscillations typically encountered on wind turbine blade sections. Depending on the jet momentum flux, steady blowing from a control slot in the leading-edge region can be utilized to either enhance or reduce lift by suppressing or inducing boundary layer separation respectively. Furthermore, high momentum blowing effectively eliminated the dynamic stall vortex during deep dynamic stall conditions. Based on these previous findings, the present work explores the feasibility of controlling unsteady aerodynamic loads by dynamically varying the jet momentum flux to compensate for transient changes of the inflow. Various scenarios including high amplitude pitching, rapid freestream oscillations and combinations of both were investigated in a custom-built unsteady wind tunnel facility. An iterative control algorithm was implemented which successfully identified the momentum coefficient time profiles required to minimize the lift excursions. The combination of fully suppressing dynamic stall and dynamically adjusting the lift coefficient provided an unprecedented control authority, producing virtually constant phase averaged lift in all cases.     

新型变桨立轴风力机涡效应分析

该文旨在通过变桨来改善升力型立轴风力机叶片气动特性,提高风力机最大运行效率。针对设计尖速比下风能利用系数较低的问题,提出减小叶片小攻角范围,增大叶片大攻角工作范围,以重点改善叶片低性能区域的气动特性为出发点,提高风能利用系数新变桨思路。以采用NACA0012翼型、2 m高和2 m旋转直径的两叶片H型风力机为研究对象,从涡理论来分析和比较在最佳尖速比为5的条件下,附着涡、尾随涡、脱体涡和桨距角对攻角、切向力和功率输出的影响规律。研究结果表明:变桨后,叶片的攻角、切向力和输出功率在原最大值两侧均有明显提高,拓宽了叶片高性能的工作区域;涡系中脱体涡对叶片气动特性影响最大,其中在上盘面影响较小,在下盘面影响较大;变桨前后涡系对上盘面的差异较小,对下盘面的影响差异较明显;变桨后,下盘面的叶片的涡尾迹弯曲程度在加大。     

Airfoil wind tunnel correction for angles of attack from −180° to 180°

Wind tunnel corrections are investigated for two‐dimensional low‐speed wind tunnel tests that are performed for three similar airfoils for angles of attack ranging from ?180° to 180° at Re = 0.75 × 10⁶. Aided by the Blasius theorem, wind tunnel corrections are deduced for the lift, drag and pitching moment of the airfoil at high angles of attack. The wall pressure signature method is applied to determine the strengths of the equivalent singularities. The tunnel wall‐induced force and pitching moment are obtained by calculating the force and moment exerted on the equivalent singularities. The maximum correction for drag is determined to be about 50%. The corrected forces and pitching moments for three similar airfoils are coincident with one another. A method to determine an optimum singularities distribution range is presented. The results indicate that the correction method in the paper is effective for airfoil testing at high angles of attack. Copyright © 2014 John Wiley & Sons, Ltd.     

水介质中尾部锯齿结构叶片数值计算

为了验证将空气动力学中翼型部件采用的锯齿形尾部结构引入到水力机械翼型部件中的可行性,建立了NACA0012型对称型叶片的几何模型,并在此基础上建立了尾部带锯齿的NACA0012型叶片修改模型,利用数值计算方法计算了在入流速度10 m/s下带锯齿与不带锯齿的NACA0012型叶片在0°及10°攻角下的流场数据及压力脉动数据。计算结果表明,锯齿形边缘结构在攻角为10°时能有效减小叶片尾部、背水面的脱流及尾迹中的漩涡和流场中的水力振动,锯齿结构改善叶片水力性能效果显著;而攻角为0°时流场中水力振动轻微增加。由此说明,锯齿结构可起到改善水介质中翼型部件水力特性的作用。     

风力机翼型尾缘厚度对粗糙敏感性影响的研究

综合应用涡面元和RANS方法,研究DU93-W-210、DU91-W2-250及DU97-W-300这3种常用翼型经尾缘修型后尾缘厚度对粗糙敏感性的影响.在涡面元方法中采用设置固定转捩和在RANS方法中采用设置锯齿形边界条件的方式来模拟翼型前缘污染,研究发现前缘污染造成翼型吸力峰降低,引起翼型气动性能下降,然而随着尾缘...     

风力机叶片翼型优化设计

为设计出气动性能优异的风力机翼型,运用CST参数化方法表述翼型外形特征以控制翼型型线,利用自适应遗传算法耦合XFOIL软件的翼型优化方法,以翼型NACA 63-215为优化算例,在设计工况下寻优,得到一种升力系数、阻力系数、升阻比、力矩等气动特性均较NACA 63-215更优的翼型,证明了该优化方法的可行性,为风力机翼型优化设计提供了参考。     

Numerical/experimental investigations on reducing drag penalty of passive vortex generators on a NACA 4415 airfoil

A study emphasizing the effects of passive vortex generators (VGs) on aerodynamic characteristics of a NACA 4415 airfoil is presented. Both experimental and numerical works have been carried out on an array of VGs attached to a NACA 4415 airfoil. Lift and drag measurements are made at various angles of attack by using three‐axis component balance system. On the numerical side, Reynolds‐averaged Navier‐Stokes (RANS) equations have been solved with ANSYS FLUENT 14.5 commercial code with fully structured mesh and three turbulence models (realizable k‐ε, k‐ω shear stress transport [SST] and the Spalart‐Allmaras model) at Reynolds number Re = 2 × 10⁵. Parametric studies have been conducted to find out optimal configurations with respect to span‐wise separation distance between VGs, along with their location along the chord. A very good agreement has been obtained between experimental and computational results indicating that this optimized configuration is robust for the considered parameters. It turns out that increasing the span‐wise separation length increases the aerodynamic performances (lift‐to‐drag ratio) at low attack angles for which low parasitic drag is achieved but conversely degrades it at higher ones. For the stream‐wise location along the chord, upstream position of VGs degrades the lift‐to‐drag ratio at low attack angles and conversely improves it at higher ones.     

尾缘气动弹片对翼型动态失速特性影响研究

通过研究尾缘气动弹片对翼型动态失速特性影响,提出一种基于气动弹片的主动控制策略,使其于大攻角时抬起,小攻角时闭合。并采用计算流体动力学方法对比分析主动式气动弹片对不同厚度翼型抑制流动分离作用的效果。结果表明：对于薄翼型,发生动态失速时,气动弹片可延缓翼型尾缘涡旋与前缘主流涡的相互作用,减小翼型升力系数骤降幅度;随翼型厚度增加,流动分离点从翼型前缘转向后缘,气动弹片可有效分割较大分离涡,减轻流动分离程度,限制分离涡发展,同时抑制尾缘伴随小涡产生,提高翼型升阻比。     

翼型前缘对风力机翼型气动性能的影响

基于翼型参数化方法对翼型S809进行两类不同的前缘修改,采用翼型设计分析软件Xfoil对修改前、后的翼型进行气动性能计算分析,并采用计算流体力学（CFD）数值模拟方法进行流场特性分析。结果表明：翼型前缘下弯使得翼型在失速区升力系数增大,阻力系数减小,俯仰力矩系数减小,转捩现象延迟,翼型前缘上弯对气动性能的影响与之相反;翼型前缘上弯和下弯使得翼型表面压力系数分布均匀,吸力面及压力面压力系数增大;翼型前缘下弯能够抑制流动分离,抑制涡的形成,延迟翼型失速,翼型前缘上弯对翼型流场特性的影响则与之相反。     

基于小样本神经网络与多约束的风力机翼型快速优化设计

针对神经网络模型可以基于现有数据快速准确地预测风力机翼型的气动性能,但大量学习样本的构建需要较高的时间成本的问题,建立基于小样本集的风力机翼型神经网络模型,提出了多约束条件下的翼型气动性能优化设计方法,解决了训练数据过少所造成的学习不充分问题。基于建立的优化设计模型,应用粒子群算法完成了NACA4415翼型的优化设计,将新翼型与原始翼型进行气动特性对比分析。结果表明：新翼型在主要工作攻角范围内最大升力系数提高了6.96%,最大升阻比提高了7.37%,气动性能明显改善;该方法的优化效率远远高于传统方法,从而验证了该方法的可行性。     

A stochastic model for the simulation of wind turbine blades in static stall

The aim of this work is to improve aeroelastic simulation codes by accounting for the unsteady aerodynamic forces that a blade experiences in static stall. A model based on a spectral representation of the aerodynamic lift force is defined. The drag and pitching moment are derived using a conditional simulation technique for stochastic processes. The input data for the model can be collected either from measurements or from numerical results from a Computational Fluid Dynamics code for airfoil sections at constant angles of attack. An analysis of such data is provided, which helps to determine the characteristics of stall. The model is applied to wind turbine rotor cases, including the stand still condition, and results are compared to experimental data. Copyright © 2009 John Wiley & Sons, Ltd.     

襟翼翼缝结构改进设计控制流动分离的数值研究

翼缝是翼型主体与襟翼之间的缝隙,对翼型气动性能与流场结构有很大影响。以两段式NACA0018翼型为基础翼型,对传统弯曲翼缝进行改进设计与数值模拟,以期增大失速攻角及改善在大攻角下的气动性能。结果表明:在小攻角下,导叶翼缝襟翼翼型的升力较原始NACA0018翼型小,阻力较大,但在大攻角下,导叶翼缝可减小翼缝中流体的速度损失,为翼型上表面边界层提供更多动能,从而改善流场结构及失速特性,弯曲翼缝可增大1°失速攻角,而导叶翼缝可增大8°,攻角为18°时升力系数较弯曲翼缝提升43%。因此,导叶翼缝可极大地改善翼型在大攻角下的气动性能。