Experimental and numerical investigation of tip vortex generation and evolution on horizontal axis wind turbines

The tip vortex of a wind turbine rotor blade is the result of a distribution of aerodynamic loads and circulation over the blade tip. The current knowledge on the generation of the tip vorticity in a 3D rotating environment still lacks detailed experimental evidence, particularly for yawed flow. The aim of this paper is to investigate how circulation at the blade tip behaves and how vorticity is eventually released in the wake, for both axial and 30° yawed flow conditions through the combination of experimental and numerical simulations. Stereo particle image velocimetry is used to measure the flow field at the tip of a 2m diameter, two‐bladed rotor at the TU Delft Open Jet Facility, for both axial and yawed flow; numerical simulations of the experiments are performed using a 3D, unsteady potential flow free‐wake vortex model. The generation mechanisms of the tip vorticity are established. The spanwise circulation along the blade exhibits a similar variation in both axial and yaw cases. A comparison of the chordwise directed circulation variation along the chord between axial and yawed flow is also presented and shown to be different. The analysis is based on contour integration of the velocity field. The tip vortex trajectory for axial flow confirms previous observations on the MEXICO rotor. The experimental results for yawed conditions have clearly shown how vorticity is swept radially away from the blade under the influence of the in‐plane radial component of flow. Such phenomena were only partially captured by the numerical model. The results of this work have important implications on the modelling of blade tip corrections. Copyright © 2015 John Wiley & Sons, Ltd.     

Experimental study of the effect of turbulence on horizontal axis wind turbine aerodynamics

Incident flows on wind turbines are often highly turbulent, because these devices operate in the atmospheric boundary layer and often in the wake of other wind turbines. This article presents experimental investigations of the effects of a high turbulence level on wind turbine aerodynamics. Power and thrust are measured on a horizontal axis wind turbine model in the ‘Lucien Malavard’ wind tunnel. A grid is used to generate three turbulence levels (4·4%, 9% and 12%) with integral length scale of the order of magnitude of the chord length. Experiments show little effect of turbulence on the wind turbine model power and thrust. This can be justified by analysis of the aerodynamic loads along the blade. Copyright © 2005 John Wiley & Sons, Ltd.     

Analysis of a small horizontal axis wind turbine performance

A small‐scale horizontal axis wind turbine capable of producing 100 W of rated power has been designed and tested using a low‐speed wind tunnel. Power output from the wind turbine was calculated through measurements of the electrical current from a 12 V DC generator. Annual energy extraction from this wind turbine shows that a number of potential applications are possible especially in the remote areas where extension of power grid is not feasible. Copyright © 2001 John Wiley & Sons, Ltd.     

Influence of microcylinders with different vibration laws on the flow control effect of a horizontal axis wind turbine

Due to the flow separation on the blade of the NREL Phase VI wind turbine, a new flow control technique involving installation of an off‐surface vibrating small structure is proposed. By considering the actual flow condition, fluid‐solid coupling is applied in which two kinds of microcylinder vibration modes are set up, and the aerodynamic performance is numerically studied. The influence of the vibration modes, amplitude, and frequency of the off‐surface vibrating small structure on the aerodynamic performance is explored. For various stall conditions, the flow separation can be well suppressed by utilizing a suitable vibrating microcylinder rather than a static microcylinder. In addition, the vibrating microcylinder shows a noticeable suppression effect on large flow separation. Both the vibration direction and vibration amplitude play leading roles in the improvement of the aerodynamic performance, and a microcylinder with a high vibration frequency can more quickly suppress surface flow separation to achieve an optimum aerodynamic performance than a microcylinder with a low vibration frequency. By setting microcylinders with suitable vibration rules close to the blade surface, the wind energy coefficient can be obviously increased compared with those obtained when adding a static microcylinder or without microcylinder addition.     

大型水平轴风力机噪声的测量

阐述了风力机噪声的传播、衰减和针对噪声的评估准则,以及风力机噪声的测量原理。针对风力机噪声测量测点布置进行了优化,给出了风力机噪声的测量实验方案和装置,并且采用自由声场法对风力机噪声进行了测量,得出了风力机噪声和周围环境噪声之间的合成声压级。     

Numerical investigation of unsteady aerodynamics of a Horizontal‐axis wind turbine under yawed flow conditions

In the present study, unsteady flow features and the blade aerodynamic loading of the National Renewable Energy Laboratory phase VI wind turbine rotor, under yawed flow conditions, were numerically investigated by using a three‐dimensional incompressible flow solver based on unstructured overset meshes. The effect of turbulence, including laminar‐turbulent transition, was accounted for by using a correlation‐based transition turbulence model. The calculations were made for an upwind configuration at wind speeds of 7, 10 and 15 m/sec when the turbine rotor was at 30° and 60° yaw angles. The results were compared with measurements in terms of the blade surface pressure and the normal and tangential forces at selected blade radial locations. It was found that under the yawed flow conditions, the blade aerodynamic loading is significantly reduced. Also, because of the wind velocity component aligned tangent to the rotor disk plane, the periodic fluctuation of blade loading is obtained with lower magnitudes at the advancing blade side and higher magnitudes at the retreating side. This tendency is further magnified as the yaw angle becomes larger. At 7 m/sec wind speed, the sectional angle of attack is relatively small, and the flow remains mostly attached to the blade surface. At 10 m/sec wind speed, leading‐edge flow separation and strong radial flow are observed at the inboard portion of the retreating blade. As the wind speed is further increased, the flow separation and the radial flow become more pronounced. It was demonstrated that these highly unsteady three‐dimensional aerodynamic features are well‐captured by the present method. Copyright © 2012 John Wiley & Sons, Ltd.     

大型水平轴式风电叶片的结构设计

风电叶片是风力发电设备的关键部件之一,其制造成本占总成本的20%～30%.叶片结构是叶片捕获风能的保证,并直接影响风力发电设备的运行寿命.因此,叶片结构设计的好坏在很大程度上决定了风力发电设备的可靠性和利用风能的成本.文章从材料、结构形式、铺层设计、结构分析等4个方面详细地阐述了风电叶片结构的设计技术.     

A study on stall-delay for horizontal axis wind turbine

The study on the stall-delay phenomenon for horizontal axis wind turbine (HAWT) was carried out by employing the boundary layer analysis, the numerical simulation and the experimental measurement. The effects of rotation on blade boundary layers are investigated by solving the 3D integral boundary layer equations with assumed velocity profiles. It is shown that rotation has a generally beneficial effect in delaying separation compared with that under 2D stationary condition. Next, the detailed flow fields are simulated on the conditions of 2D stationary and 3D rotation by CFD code. The computation results show that rotation affects the pressure distribution on the surface of the foil, which can give rise to 3D stall-delay in stalled condition HAWT. Finally, the flow fields behind a model HAWT are measured with a hot-wire probe in the wind tunnel. The results show good agreement with those from 3D computation calculations, suggesting that the stall-delay should be taken into consideration, in order to accurately predict the loading and performance of a HAWT operating in stall.     

垂直轴风力机动态流场及其气动性能分析

垂直轴风力机气动性能研究是风力机设计、实验的重要部分,对其运动状态下的流场进行分析是观测垂直轴风力机性能重要环节.基于NACA0012对称翼型,建立二维几何模型并进行模拟计算.采用k-ωSST湍流模型及滑移网格技术,通过CFD软件数值计算得到达里厄型直叶片垂直轴风力机运行时周边流场分布情况.通过比较不同方位角下流场涡量以及升、阻力系数得出:在方位角为105°附近时,翼型下表面产生流动分离,并导致失速;下风区翼型运行的流场由于受到上风区尾流的影响,翼型周围没有产生明显的流动分离.     

水平轴风力机塔架的频率和振型特性实验研究

为了研究风力机塔架的振动特性,文章利用动态信号采集分析系统,对水平轴风力机塔架进行了实验模态分析和运行模态分析测试,得到了塔架静止与振动两种工况下的固有频率与模态振型,分析了塔架的振动特性。通过对风力机振动信号的频谱分析发现,风速小于10 m/s时,只能激励起塔架挥舞方向与摆振方向的二阶模态;通过对风力机塔架的模态分析发现,风力机发生振动,塔架固有频率与模态振型发生小幅度改变;随着风速和振动烈度的增大,塔架模态参数的变化幅度随之增大。该研究可以为风力机塔架优化设计提供借鉴。     

Performance and near wake measurements of a model horizontal axis wind turbine

The performance characteristics and the near wake of a model wind turbine were investigated experimentally. The model tested is a three‐bladed horizontal axis type wind turbine with an upstream rotor of 0.90 m diameter. The performance measurements were conducted at various yaw angles, a freestream speed of about 10 m s ^?1, and the tip speed ratio was varied from 0.5 to 12. The time‐averaged streamwise velocity field in the near wake of the turbine was measured at different tip speed ratios and downstream locations. As expected, it was found that power and thrust coefficients decrease with increasing yaw angle. The power loss is about 3% when the yaw angle is less than 10° and increases to more than 30% when the yaw angle is greater than 30°. The velocity distribution in the near wake was found to be strongly influenced by the tip speed ratio and the yaw angle. At the optimum tip speed ratio, the axial velocity was almost uniform within the midsection of the rotor wake, whereas two strong peaks are observed for high tip speed ratios when the yaw angle is 0°. As the yaw angle increases, the wake width was found to be reduced and skewed towards the yawed direction. With increasing downstream distance, the wake velocity field was observed to depend on the tip speed ratio and more pronounced at high tip speed ratio. Copyright © 2011 John Wiley & Sons, Ltd.     

Flow characterization in the near‐wake region of a horizontal axis wind turbine

An experimental study is conducted to investigate the flow dynamics within the near‐wake region of a horizontal axis wind turbine using particle image velocimetry (PIV). Measurements were performed in the horizontal plane in a row of four radially distributed measurement windows (tiles), which are then patched together to obtain larger measurement field. The mean and turbulent components of the flow field were measured at various blade phase angles. The mean velocity and turbulence characteristics show high dependency on the blade phase angle in the near‐wake region closer to the blade tip and become phase independent further downstream at a distance of about one rotor diameter. In the near‐wake region, both the mean and turbulent characteristics show a systemic variation with the phase angle in the blade tip region, where the highest levels of turbulence are observed. The streamlines of the instantaneous velocity field at a given phase allowed to track a tip vortex which showed wandering trend. The tip vortices are mostly formed at r/R > 1, which indicates the wake expansion. Results also show the gradual movement of the vortex region in the axial direction, which can be attributed to the dynamics of the helical tip vortices which after being generated from the tip, rotate with respect to the blade and move in the axial direction because of the axial momentum of the flow. The axial velocity deficit was compared with other laboratory and field measurements. The comparison shows qualitative similarity. Copyright © 2015 John Wiley & Sons, Ltd.     

Upwind preview to a horizontal axis wind turbine: a wind tunnel and field‐scale study

Data collected at the Eolos wind research facility and in the Saint Anthony Falls Laboratory atmospheric boundary layer wind tunnel are used to study the impact of turbulent inflow conditions on the performance of a horizontal axis wind turbine on flat terrain. The Eolos test facility comprises a 2.5MW Clipper Liberty C96 wind turbine, a meteorological tower and a WindCube LiDAR wind profiler. A second set of experiments was completed using particle image velocimetry upwind and in a wake of a miniature turbine in the wind tunnel to complement LiDAR measurements near the Eolos turbine. Joint statistics, most notably temporal cross‐correlations between wind velocity at different heights and turbine performance, are presented and compared at both the laboratory and field scales. The work (i) confirms that the turbine exerts a blockage effect on the mean flow and (ii) suggests a key, specific elevation, above hub height, where the incoming velocity signal is statistically most relevant to turbine operation and control. Wind tunnel measurements confirm such indication and suggest that hub height velocity measurements are optimal for wind preview and/or as input for active control strategies in aligned turbine configurations. Copyright © 2015 John Wiley & Sons, Ltd.     

雾霾之后的反思

新年过后的第二个周末,浓重的雾霾已在全国多个城市肆虐,这让人们的心情变得糟糕。数据显示,截至1月13日零时,全国有33个城市的部分监测点PM2.5浓度超过300微克/立方米,个别城市出现PM2.5"爆表",比如北京的PM2.5浓度最高达到950微克/立方米。环保专家称,如此严重的空气质量污染,可以说已近人类所能承受的极限。于是,人们看到了政府有关方面发布的紧急预案,比如通知市民减少户外活动,要求学校停止户外体育锻炼,这体现了政府的责任意识。但我们是满足于制定完美的灾情应对预案,还是谋求从根本上消除灾难?     

Investigating the aerodynamic performance of a model offshore floating wind turbine

Understanding the impact of wave-induced dynamic effects on the aerodynamic performance of Offshore Floating Wind Turbines (OFWTs) is crucial towards developing cost-effective floating wind turbines to harness wind energy in deep water sites. The complexity of the wake of an OFWT has not yet been fully understood. Measurements and numerical simulations are essential. An experiment to investigate the aerodynamics of a model OFWT was undertaken at the University of Malta. Established experimental techniques used to analyse fixed HAWTs were applied and modified for the floating turbine condition. The effects of wave induced motions on the rotor aerodynamic variables were analysed in detail. An open source free-wake vortex code was also used to examine whether certain phenomena observed in the experiments could be reproduced numerically by the lifting line method. Results from hot wire measurements and free-wake vortex simulations have shown that for OFWTs surge-induced torque fluctuations are evident. At high λ a discrepancy in the mean C_P between the fixed and floating conditions was found from measurements and numerical simulations.     

Early development of a shaftless horizontal axis wind turbine for generating electricity from air discharged from ventilation systems

The air discharged from ventilation systems is a high potential wind resource for generating electricity in countries where wind speed is unreliable or weak, such as in Thailand. The air discharged from ventilation systems produces consistent and high-speed wind when benchmarked against natural wind. However, the limitations of conventional wind turbines are that they have negative impacts on the ventilation system and are inconvenient to install in many areas. The innovative shaftless horizontal axis wind turbine (SHWT) introduced in this article has been designed to close the gap between the wind source and the conventional wind turbines in this process. The concept design shows how it could be mounted next to sources of waste wind, requiring only a small space for installation. An open hole is provided to enable airflow to be discharged into the environment. This SHWT has high market potential for utilizing man-made wind to generate electricity from an alternative source which supports sustainable energy development. The purpose of this study is to demonstrate the concept design of a prototype SHWT used for energy recovery from the discharged air of a ventilation system. How the rotor and stator design of the SHWT optimize wind turbine performance and minimize the negative effects on the ventilation system efficiency are also addressed in this study. The performance of the SHWT is demonstrated in a lab-scale test using the type of propeller fan that is generally applied in many sectors in Thailand. The results showed that the SHWT was successful in generating electricity and produced minimal negative effects on the ventilation system's performance. The maximum power output of the prototype SHWT is 7.4 W at a rotational speed of 1644 rpm using eight sets of magnets and 5.1 m/s wind speed. The maximum wind turbine efficiency is 51%. However, it still requires further optimization to enhance the SHWT performance.     

Application and validation of incrementally complex models for wind turbine aerodynamics,isolated wind turbine in uniform inflow conditions

A comparison of several incrementally complex methods for predicting wind turbine performance, aeroelastic behavior, and wakes is provided. Depending on a wind farm's design, wake interference can cause large power losses and increased turbulence levels within the farm. The goal is to employ modeling methods to reach an improved understanding of wake effects and to use this information to better optimize the layout of new wind farms. A critical decision faced by modelers is the fidelity of the model that is selected to perform simulations. The choice of model fidelity can affect the accuracy, but will also greatly impact the computational time and resource requirements for simulations. To help address this critical question, three modeling methods of varying fidelity have been developed side by side and are compared in this article. The models from low to high complexity are as follows: a blade element‐based method with a free‐vortex wake, an actuator disc‐based method, and a full rotor‐based method. Fluid/structure interfaces are developed for the aerodynamic modeling approaches that allow modeling of discrete blades and are then coupled with a multibody structural dynamics solver in order to perform an aeroelastic analysis. Similar methods have individually been tested by researchers, but we suggest that by developing a suite of models, they can be cross‐compared to grasp the subtleties of each method. The modeling methods are applied to the National Renewable Energy Laboratory Phase VI rotor to predict the turbine aerodynamic and structural loads and then also the wind velocities in the wake. The full rotor method provides the most accurate predictions at the turbine and the use of adaptive mesh refinement to capture the wake to 20 radii downstream is proven particularly successful. Though the full rotor method is unmatched by the lower fidelity methods in stalled conditions and detailed prediction of the downstream wake, there are other less complex conditions where these methods perform as accurately as the full rotor method. Copyright © 2014 John Wiley & Sons, Ltd.