Effect of friction cycles on wear particle generation of carbon nitride coating against a spherical diamond

The in-situ observations of wear particle generation of carbon nitride coating on silicon repeatedly sliding against a spherical diamond have been studied in terms of the critical friction cycles and normal loads. An environmental scanning electron microscope (E-SEM), in which a pin-on-disk tribotester was installed, has in-situ provided direct evidence of when and how the wear particle generation do occur during the repeated sliding of carbon nitride coating against a spherical diamond. The in-situ observations of non-conductive carbon nitride coating are therefore available free from surface charging with controllable relative humidity. The repeated sliding tests at a sliding speed of 50 μm/s have been carried out with the purpose of observing the ‘No wear particle generation’ region when varying normal load from 10 to 250 mN. It appears that until 20 friction cycles, the maximum Hertzian contact pressure P_max for ‘No wear particle generation’ can be improved from 1.39 Y to 1.53 Y if silicon is coated by carbon nitride with a thickness of 10 nm, where Y is defined as the yield strength of silicon. The applicable enlargement of the ‘No wear particle generation’ region of carbon nitride coating has therefore been comparatively discussed with the silicon substrate from the view points of the friction coefficient and the specific wear rate. The mode transition maps have also been summarized for the repeated sliding of carbon nitride coating in terms of ‘No wear particle generation’, ‘Wear particle generation by microcutting’ and ‘Wear particle generation by microcutting and microfracturing’ three typical modes.     

Critical load for wear particle generation in carbon nitride coatings by single sliding against a spherical diamond

The ‘critical load' for wear particle generation of carbon nitride coatings sliding against a spherical diamond under a linearly increasing load has been examined in situ in relation to different nitrogen incorporation conditions, i.e. assisted N ion acceleration energy and N ion beam current density, and different coating thickness. An environmental scanning electron microscope (E-SEM), in which a pin-on-disk tribotester was installed, has provided direct evidence in situ of when, how and where wear particle generation occurs during the sliding of carbon nitride coatings against a spherical diamond. The in-situ examination of non-conductive carbon nitride coatings are available in E-SEM free from surface charging with controllable relative humidity. The sliding tests under linearly increasing load up to 300 mN at a sliding speed of 10 μm/s have been carried out with the purpose of measuring the ‘critical load' for wear particle generation in a similar way to the traditional macro scratch testing. However, instead of the ‘critical load', the critical maximum Hertzian contact pressure P_max will also be used in the following for better understanding. Based on the systematic study of seven combinations of nitrogen incorporation parameters and five kinds of thickness (0, 10, 50, 100 and 200 nm), the applicable range of P_max for wear particle generation can be increased from 1.6Y to 1.831.92Y or to 1.801.89Y, where Y is defined as the yield strength of silicon of 7 GPa, by coating carbon nitride onto silicon with changing nitrogen incorporation conditions of ion acceleration energy and ion current density, or varing coating thickness from 10 to 200 nm. It also appears that the observed wear particle generation of carbon nitride coatings was associated with a failure initiated in the silicon substrate rather than within the carbon nitride coating or at the coating–substrate interface in the light of both the empirical identification and the theoretical discussion.     

Friction and wear behaviour of hard and superhard coatings at cryogenic temperatures

The work presents data on friction and wear behaviour of pin-on-disc pairs with superhard diamond-like carbon (DLC) coatings and hard coatings of zirconium nitride (ZrN) and titanium nitride (TiN) in liquid nitrogen with loads of 2.5 and 10 N and sliding speed of 0.06 m/s. It is shown that at cryogenic temperatures the friction coefficients of pairs of two types of DLC coatings obtained by vacuum-arc deposition of filtered high-speed carbon plasma fluxes depend to a great deal on the mechanical properties of the coatings defined by predominant sp² or sp³ hybridization of valence electrons. A friction coefficient of 0.76 was observed for friction pairs of superhard (90 GPa) DLC coatings having properties similar to those of diamond. For “softer” DLC coatings of 40 GPa and properties similar to those of graphite the friction coefficient shows lower values (0.24–0.48) dependent on normal load and counterbody material. The DLC coatings obtained by the filtered arc technology exhibit good wear resistance and have strong adhesion to the substrate under friction in liquid nitrogen. With a normal load of 10 N under cryogenic temperature a low wear rate (of the order of 7.2×10⁻⁴ nm/cycle) was found for superhard DLC coatings. The friction coefficient of pairs with hard ZrN and superhard DLC coatings on steel discs was revealed to be linearly dependent on the counterbody material hardness between 20 and 100 GPa. The hardness of the pin was varied by means of depositing TiN or DLC coatings and also by using high-hardness compounds (boron nitride and synthetic diamond). Proceeding this way can be promising since it offers the possibility of creating low-temperature junctions of required friction properties.     

Friction and Wear Characteristics of C/Si Bi-layer Coatings Deposited on Silicon Substrate by DC Magnetron Sputtering

The tribological behavior of carbon/silicon bi-layer coatings deposited on a silicon substrate by DC magnetron sputtering was assessed and compared to that of amorphous carbon and silicon coatings. The motivation was to develop a wear resistant coating for silicon using thin layers of amorphous carbon and silicon. Wear tests were conducted by sliding a stainless steel ball against the coating specimens under applied normal loads in the range of 20?~?50?mN. Results showed that the wear rate of the bi-layer coating was strongly dependent on the ratio of thickness between the carbon and silicon layers. The wear rate of the bi-layer coating with 25?nm thick carbon and 102?nm thick silicon layers was about 48 and 20 times lower than that of the single-layer amorphous carbon and amorphous silicon coating, respectively. In addition, the steady-state friction coefficient of the bi-layer coating could be decreased to 0.09 by optimizing the thickness of the layer. Finally, a model for the wear reduction mechanism of the carbon/silicon bi-layer coating was proposed.     

The effects of texture height and thickness of amorphous carbon nitride coating of a hard disk slider on the friction and wear of the slider against a disk

In order to minimize the stiction force caused by contact of the extremely smooth surfaces of head sliders and disks in hard disk drives, texture is usually applied on the disk surface. For future contact/near-contact recording, the stiction-induced high friction between slider and disk will become a problem. Texture on the slider/disk interface will still be an expected method to reduce friction. Recently, it was suggested to texture the slider surface. A protective coating is usually required on the textured slider surface to reduce wear of the texture. The results showed that texture on the slider surface was effective in reducing the friction between head sliders and disks. On the other hand, the texture and coating on the slider surface increase the spacing between the read/write element and the magnetic layer of the disk. The necessary and effective texture height and coating thickness are still not clear. In the present research, island-type textures with different heights (3–18 mn) were formed on slider surfaces by ion-beam etching. Amorphous carbon nitride (a-CN_x) coatings of different thicknesses (0–50 nm) were coated on the textured slider surfaces as a protective overcoat. The friction and wear properties of these sliders were evaluated by constant-speed drag tests against hard disks coated with diamond-like carbon (DLC). The results show that 2 nm texture on a slider surface is sufficient for low (0.3–0.5) and stable friction of the slider against the disk in a drag test, and coatings thicker than 5 nm show similar wear resistances of the texture on slider surfaces.     

Influence of counterbody material on wear of ta-C coatings under fretting conditions at elevated temperatures

The high temperature tribological performance of tetrahedral amorphous carbon coatings has been analyzed at elevated temperatures up to 250 °C in air against three different counterbody materials—steel 100Cr6, α-alumina and silicon nitride. The results show that the counterbody material influences the friction and wear behavior and therefore coating life time strongly. This effect is well known for these coatings at room temperature under dry environmental conditions, equivalent to conditions above 100 °C when water molecules desorb from the surface. However, the sharp difference in tribological performance between silicon nitride on the one hand and alumina and steel on the other hand cannot be understood in this context. Analyzing the friction behavior during the running-in phase, it is evident that only alumina and steel form a stable interface with constant low friction and relatively low wear rates. Silicon nitride forms an unstable interface with fluctuating COF and relatively high wear rates due to its own inherent tendency to tribo-oxidation.     

Tribological and mechanical properties of carbon nitride thin coating prepared by ion-beam-assisted deposition

Carbon nitride thin films may become good competitors for diamond-like carbon, due to their high hardness, high wear resistance, and low friction coefficient. At present, there are only a few studies of the effect of CN _x coating hardness and internal stress on its tribological properties, such as coating life and frictional behaviour. This work deals with tribological and mechanical properties of a carbon nitride coating prepared by ion-beam-assisted deposition (IBAD). Friction coefficients in the range of 0.10–0.12 were observed for the best CN _x coatings sliding against silicon nitride under ambient conditions. A nonlinear correlation between coating life and its internal stress and hardness was found.     

Tribological behavior and topography of friction surfaces of diamond-like coatings in contact with steel,silicon nitride,and quartz glass

The paper presents the study results of the tribological behavior and surface topography formed at friction of diamond-like coatings against indenters made of silicon nitride, quartz glass, and steel. It is shown that the tribological behavior depends on the nature and hardness of the counterbody material whose wear causes changes in the surface topography of the diamond-like coating at the nanometer level. At friction of the diamond-like coating against the silicon nitride indenter surface asperities are deformed plastically and the deformation rate is governed by the coating structure.     

Palliatives in fretting: A dynamical approach

Fretting damages are connected to numerous aspects like friction, wear, contact mechanics, fatigue and material sciences. Its quantification also requests to consider the loading history as well as the sliding condition. Based on a “fretting sliding” approach, and considering fretting wear test conditions, various palliative solutions have been investigated. Shot peening treatment, introducing compressive residual stresses, appears pertinent against crack propagation but ineffective against crack nucleation due to the activation of surface relaxation phenomena. Hard thin coatings present stable residual stresses independently of the sliding conditions. However, they only delay the crack nucleation process, when the coating is worn through, cracking phenomena are activated. To quantify the coating endurance against wear, an energy density approach has been developed. The stability of this approach has been confirmed regarding the contact size effect and illustrated through the analysis of synergic interaction between soft thick coating and solid lubricant.     

Origin of Friction in Running-in Sliding Wear of Nitride Coatings

To investigate the origin of running-in friction in unlubricated sliding wear, a magnetron sputtered multilayer coating TiAlN/VN was tested on a ball-on-disc tribometer for a series of sliding durations from 10 to 1000 cycles, followed by careful observation of the obtained worn surfaces using an field-emission gun scanning electron microscope. Three steps of friction variation were found: (1) prior to wear particle generation, low initial friction coefficient was around 0.2–0.25 purely attributed to the asperity contact; (2) then it increased steeply to a range of 0.4–0.5 in the first 100 cycles following the generation, breaking and agglomeration of wear particles, and in particular the scaling-up of fish-scale-like tribofilm; (3) eventually it approached to a steady-state value around 0.5 when the friction was governed by the viscous shearing of the tribofilm. It is concluded that, under unlubricated sliding wear, the friction behaviour of transition metal nitride hard coating is dominated by the viscous shearing of tribofilm adhesively bonding to the parent nitride coating.     

Corrosion-wear behaviour of PVD Cr/CrN multilayer coatings for gear applications

At present, one of the most important problems in automobile engines and transmission components is due to tribological processes (friction and wear) that in many cases come accompanied by corrosion processes due to the environmental conditions to which these materials are exposed during their lifetime. Both mechanisms can be minimized by means of the development and the application of adequate coatings that combine low friction with a high corrosion and wear resistance.The new tendencies in industrial PVD coatings to improve their properties are focused in the development of new multilayer and nanostructured coatings. These structures allow in a relatively simple way enhancing their tribological properties and the corrosion resistance that can not be reached by means of the traditional monolayer coatings. The background of this type of coatings consists of the stacking up of several layers with good individual tribological and mechanical properties, but every individual layer has a thickness that can be from hundreds of nanometres down to only 5-10 nm. The properties of these nanostructured coatings depend strongly on the thickness modulation of every individual layer.Concerning PVD coatings, the chrome nitride coatings have demonstrated to possess excellent wear resistance properties. In this work, multilayer Cr/CrN coatings with different individual layer thickness have been deposited on substrates of steel F1272 and silicon. The deposition has been carried out by means of the cathodic arc method alternating an atmosphere of pure Ar with a reactive mixture of N₂/Ar. The multilayers obtained have been analyzed by means of Glow Discharge Optical Emission Spectroscopy (GD-OES) and in some cases by means of FE-SEM obtaining bilayer (Cr/CrN) periods of the order of 220 and 45 nm. The coating characterization has been complemented with hardness and composition measurements as well as by the performance of several wear and corrosion-wear tests.     

New cylinder liner surfaces for low oil consumption

Anticipated emission legislation and reduced fuel consumption are the main driving forces when developing new engines. Optimization of the active surfaces in the piston system is one possible way to meet the above demands. In this study the effects of surface topography and texture direction of the ring/liner contact on oil film thickness and friction were simulated and experimentally tested. “Low wear” results from the experimental wear tests with “glide honed” smooth liner surfaces supported the “low friction” simulation results. In addition a new wear volume sensitive surface roughness parameter, R_ktot, based on the Abbot–Firestone bearing area curve was introduced.     

Tribological Characteristics of Oxide Layer Formed on TiN Coated Silicon Wafer

The effects of the oxide layer formed on the wear tracks of a titanium nitride (TiN) coated silicon wafer on friction and wear characteristics were investigated. Silicon wafers were used as the substrate of coated disk specimens, which were prepared by depositing TiN coating with 1.74 m in coating thickness using the arc ion-plating method. SAE 52100 steel balls were used as the counter-faces. The tests were performed both in air for forming an oxide layer on the wear track and in nitrogen to avoid oxidation. This paper reports the characterization of the oxide layer and its effects on friction and wear characteristics using Auger electron spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The TiN coating with the oxides shows relatively high friction compared to that without an oxide layer. The thickness of the layer formed on the surfaces of the TiN coated silicon wafer is very thin compared to the thickness of the TiN coating. The oxide layer dominates the frictional characteristics between the two materials and induces a relative high friction.     

Method of movable lattice particles

A new simulation technique for modeling elastoplastic deformation and friction processes based on the dynamics of a system of “lattice particles” is proposed. In usual simulation methods like molecular dynamics, only interactions compatible to the symmetries of space (invariant with respect to translations and rotations) are used. In the proposed method, the interaction potentials depend both on the relative position of particles and the orientation of their relative radius vector with respect to prescribed “lattice directions”. We show that in spite of this relation with the “external space”, the system behaves, in linear approximation, as an isotropic elastic medium invariant to both the translations and rotations of the medium as a whole. The coupling with the external space occurs to be a surface effect, which either does not play an important role (if the motions of the boundaries are prescribed) or can be handled properly by introducing fictive compensating surface forces. Introduction of forces depending on the orientation of the local surroundings of a particle makes it possible to describe elastic media with arbitrary elastic properties by using only interactions between the next neighbours. The system of lattice particles shows better stability properties and allows one to describe large plastic deformations, avoiding problems of “packaging” typical for many particle methods.     

Role of the Transfer Film on the Friction and Wear of Metal Carbide Reinforced Amorphous Carbon Coatings During Run-in

The relationship between friction, wear, and transfer films of three metal carbide-reinforced amorphous carbon coatings (TiC/a:C, TiC/a:C–H, and WC/a:C–H), sometimes referred to as metal-doped diamond-like carbon coatings, has been investigated. Tribological tests were performed in an in situ tribometer with sapphire or steel hemispheres run against coated flats in dry or ambient air. The sliding contact interface was observed and recorded by optical microscopy during reciprocating sliding tests. The friction and wear behavior during run-in depended on the number of sliding cycles to form a stationary transfer film on the hemisphere. Stationary transfer films formed rapidly (within ten cycles) and the friction coefficient fell to 0.2 (ambient air) or 0.1 (dry air), except with sapphire against WC/a:C–H in dry air; with the latter, a stationary transfer film required nearly 100 cycles to form, during which the friction remained high and the wear rate was from 10 to 100 times higher than the other two coatings. For all coatings, three velocity accommodation modes (VAM) were observed from run-in to steady-state sliding and were correlated with the friction and wear behavior. The delayed adherence of the transfer film to sapphire from WC/a:C–H coatings in dry air is discussed in terms of equilibrium thermochemistry. Friction and wear behavior during run-in, therefore, depended on transfer film adherence to the hemisphere and the VAM between transfer films and the coating.     

In vitro analysis of the wear,wear debris and biological activity of surface-engineered coatings for use in metal-on-metal total hip replacements

Extremely low wear rates have been reported for metal-on-metal total hip replacements, but concerns remain about the effects of metal ion release, dissolution rates and toxicity. Surface-engineered coatings have the potential to improve wear resistance and reduce the biological activity of the wear debris produced. The aim of this study was to examine the wear and wear debris generation from surface-engineered coatings: titanium nitride (TiN), chromium nitride (CrN) and chromium carbon nitride (CrCN) applied to a cobalt-chrome alloy (CoCr) substrate. The coatings were articulated against themselves in a simple geometry model. The wear particles generated were characterized and the cytotoxic effect on U937 macrophages and L929 fibroblasts assessed. The CrN and CrCN coatings showed a decrease in wear compared to the CoCr bearings and produced small (less than 40 nm in length) wear particles. The wear particles released from the surface engineered bearings also showed a decreased cytotoxic effect on cells compared to the CoCr alloy debris. The reduced wear volumes coupled with the reduced cytotoxicity per unit volume of wear indicate the potential for the clinical application of this technology.     

Coating thickness effect on initial wear of nitrogen-doped amorphous carbon in nano-scale sliding contact: Part II—theoretical modeling

This is the second paper of a two-part report. In the first paper, empirical data on the wear particle generation in carbon nitride coatings subjected to repeated sliding contact with a spherical diamond counter-face is reported. The effect of coating thickness on the wear particle generation is also discussed in the first paper. In this paper, a simplified theoretical expression, combining the Coffin-Manson equation with the analytical solution of a proposed elastic perfectly-plastic indentation model, is introduced. The expression successfully correlates critical number of friction cycles for wear particle generation N_c to coating thickness h, contact pressure P and radius of spherical asperity on the tip of the diamond pin R. With this expression, the lifespan of sliding components can be predicted.The theoretical results computed for diamond pin with a specific asperity radius value of 250 nm were compared with the experimental results reported in the first paper. The theoretical model successfully predicts the maximum lifespan of a component, N_c, in repeated sliding applications. The influences of various contact pressures and asperity radii on the maximum lifespan were also assessed using the model.     

Friction and wear characteristics of ion-beam modified graphite coatings

Solid lubricated surfaces are now widely used in the tool industry, and the new concept of ‘soft tools’ recently introduced has emphasized low-friction surfaces. The present paper deals with a novel ‘burnishing’ process based on ionic bombardment of powder graphite coating/substrate systems. This process may influence both the coating and the coating/substrate interface, and it is effective for improving lubrication even at low doses of bombarding ions. The present study will discuss the friction and wear properties of graphite-powder coatings on a silicon wafer bombarded with 200 keV ion beams of argon, nitrogen and hydrogen ions, the last two as molecular ions. The coefficients of friction and wear rates of the coatings were found to be strongly dependent on the ion-bombarding species and ion dose. The argon ion bombardment increased the coefficient of friction and wear rate of the powder coating. However, at the interface of the silicon substrate, the ion-induced burnishing improved the tribological behaviour of the silicon material. Bombardment with nitrogen and hydrogen ions showed a marked improvement in the tribological properties of the graphite powder coating. Thus a reduction in wear rate by three orders of magnitude was observed in the case of nitrogen, and for both ions it was noted that ion-beam burnished graphite was lubricating in a dry environment, which has not been reported previously. The perspectives of ion bombardment as a burnishing process will be discussed and the observed effects will be qualitatively explained in the context of the theory for ionic penetration into solids.     

Microstructure and wear properties of in situ TiC/FeCrBSi composite coating prepared by gas tungsten arc welding

Using a gas tungsten arc welding (GTAW) process, in situ synthesis TiC particles reinforced Fe-based alloy composite coating has been produced by pre-coated FeCrBSi alloy, graphite and ferrotitanium powders on the substrate. The microstructure and wear properties of the composite coatings were studied by means of scanning electron microscopy (SEM), X-ray diffractometer (XRD) and wear test. The effects of thickness of the pre-coated powder layer on the microstructure, hardness and wear resistance of the composite coatings were also investigated. The results indicated that TiC particles were produced by direct metallurgical reaction between ferrotitanium and graphite during the GTAW process. TiC particles with sizes in the range of 3–5 μm were dispersed in the matrix. The volume fraction of TiC particles and microhardness gradually increased from the bottom to the top of the composite coatings. The TiC-reinforced composite coatings enhance the hardness and wear resistance. The highest wear resistance of the composite coating with a 1.2 mm layer was obtained.     

Microstructure and wear properties of in situ TiC/FeCrBSi composite coating prepared by gas tungsten arc welding

Using a gas tungsten arc welding (GTAW) process, in situ synthesis TiC particles reinforced Fe-based alloy composite coating has been produced by preplaced FeCrBSi alloy, graphite and ferrotitanium powders. The microstructure and wear properties of the composite coatings were studied by means of scanning electron microscopy (SEM), X-ray diffractometer (XRD) and wear test. The effects of thickness of the pre-placed powder layer on the microstructure, hardness and wear resistance of the composite coatings were also investigated. The results indicated that TiC particles were produced by direct metallurgical reaction between ferrotitanium and graphite during the GTAW process. TiC particles with sizes in the range of 3–5 μm were dispersed in the matrix. The volume fraction of TiC particles and microhardness gradually increased from the bottom to the top of the composite coatings. The TiC-reinforced composite coatings enhance the hardness and wear resistance. The highest wear resistance of the composite coating with a 1.2 mm layer was obtained.