Precision energy and intensity measurements for γ transitions from Cs decay

The precision energies and relative intensities of 11 γ transitions from the decay of ¹³⁴Cs have been determined. ¹⁹²Ir, ²²⁸Th, ¹³⁷Cs, ^110mAg, ⁶⁰Co, and ²⁰⁷Bi served as energy calibration standards, and ¹⁵²Eu and ¹⁹²Ir as relative intensity calibration standards. Special care was taken in the analysis of data for the weaker transitions. The results are incorporated into a self-consistent decay scheme.     

Detection of γ-rays with a 3.5 l liquid xenon ionization chamber triggered by the primary scintillation light

A gridded ionization chamber with a drift length of 4.5 cm and a total volume of 3.5 l, was operated with high-purity liquid xenon and extensively tested with γ-rays from ¹³⁷Cs, ²²Na and ⁶⁰Co radioactive sources. An electron lifetime in excess of 1 ms was inferred from two independent measurements. The electric field dependence of the collected charge and energy resolution was studied in the range 0.1–4 kV/cm, for different γ-ray energies. With an electric field of 4 kV/cm, the spectral performance of the detector is consistent with an energy resolution of 5.9% at 1 MeV, scaling with energy as E^−0.5. The chamber was also used to detect the primary scintillation light produced by γ-ray interactions in liquid xenon. The light signal was successfully used to trigger the acquisition of the charge signal with a FADC readout. A trigger efficiency of 85% was measured at 662 keV.     

富集10B的Ce:Li6Lu(10BO3)3晶体生长及其闪烁性能

为了提高中子探测效率, 以富集¹⁰B的H₃¹⁰BO₃为原料, 通过提拉法生长了富集¹⁰B的Ce:Li₆Lu(¹⁰BO₃)₃晶体。X射线激发发射光谱测试表明: 其发光峰位于360~480 nm, 属于Ce³⁺离子典型的5d - 4f跃迁发光, 其闪烁发光效率为BGO晶体的3.9倍。在350 nm紫外光和¹³⁷Cs所发出的662 keV的γ射线激发下测得的衰减时间分别为21.0 ns 和31.7 ns, 在¹³⁷Cs辐射源激发下所测得的相对光输出是CsI(Tl)晶体的20%, 能量分辨率为9.7%。在慢化²⁵²Cf中子源激发下可以观测到明显的中子全能峰, 其能量分辨率为33%。上述研究结果表明, Ce:Li₆Lu(¹⁰BO₃)₃晶体具有较高的闪烁效率、快的衰减时间和良好的中子探测效率, 是一种具有应用前景的中子探测用闪烁晶体。     

Characterization of charge collection in CdTe and CZT using the transient current technique

The charge collection properties of Cadmium–Telluride (CdTe) and Cadmium–Zinc–Telluride (CZT) in comparison with Silicon (Si) are presented using the transient-current technique (TCT) where the current pulses are generated by -particles emitted from an ²⁴¹Am source. From the recorded current pulse shapes, the charge collection efficiency, the charge carrier mobility and the electric field distribution inside the detectors are extracted. In particular, the signals of the compound semiconductors CdTe and CZT are interpreted with respect to the build-up of space–charges in the sensor volume and the subsequent deformation of the electric field. As high-quality CdTe and CZT samples are now commercially available, the knowledge of these material characteristics is of outmost importance for the application of CdTe and CZT in X-ray imaging.

In addition, the paper describes the influence of Ohmic and Schottky contacts on the current pulses in CdTe as well as the effects of polarization, i.e. the time-dependent degradation of the detector signals due to the accumulation of fixed charges within the sensor.     

Factorial Modeling for Transient Solid Particle Velocity in a Fluidized Bed Combustor Cold Model

Transient hydrodynamics phenomena in the fluidized bed combustor (FBC) freeboard have been critical in the past two decades. Within a 152 mm ID FBC cold model, solid particle transient velocities were measured and analyzed with the assistance of advanced laser-based particle image velocimetry (PIV) instrumentation. Two layers of swirling secondary air were injected into the cold model. The PIV system was applied to the FBC cold model to visualize transient solid particle velocity. A series of transient solid particle velocity profiles were generated for the factorial analysis. In each profile, the solid particle velocity vectors (Vx and Vy) for 10 × 10 grids were generated. Analysis of variance (ANOVA) was used to determine the significant factors that affect transient solid particle velocities, time, and position coordinates. Then, the 10¹⁰ factorial design method was used to develop a specific empirical model of transient solid particle velocity in the FBC freeboard, which was in the shape of V_x = f₁(t, x, y) and V_y = f₂(t, x, y).

This unique factorial analysis method proved to be a very effective and practical method to evaluate experimental conditions and analyze experimental results in the FBC systems.     

A coincidence system for radionuclide standardization using surface barrier detectors

A system for the standardization of alpha-gamma or electron-X radionuclide emitters is described. The system consists of one or two surface barrier detectors for alpha or electron detection which are coupled to thin-window NaI(Tl) crystals suitable for low-energy X- or gamma-ray detection. The performance of the system has been verified by the standardization of ²⁴¹Am, ¹³⁷Cs and ¹⁰⁹Cd solutions. The activity has been obtained using the extrapolation method applied to the 4π -γ and 2π e-X coincidence techniques. The surface barrier detection efficiency was varied by placing absorbers over the radioactive source or by changing the source-to-detector distance. The results were compared to those obtained using conventional absolute systems based on gas-flow and pressurized 4π proportional counters, or using radioactive solutions standardized in international comparisons sponsored by the Bureau International des Poids et Mesures, France. The expected and measured activities agreed within the experimental uncertainties, which were: 0.2% for ²⁴¹Am, 0.7% for ¹³⁷Cs and 0.6% for ¹⁰⁹Cd.     

Approximated total and full energy peak intrinsic efficiencies of gamma detectors for measuring systems design

Functions characterizing the performance of gauges based on gamma radiation correlate the design parameters and the variables to be measured. The radiation detector is a major component of the gauge. Analytic expressions for the total and full energy peak efficiencies were derived using the mean chord length in the detector's sensitive volume. The errors associated with this approximation were estimated from the distribution of the chord length. The uncertainties found in the determined total intrinsic efficiency are in the range of a few percent for most practical industrial gauges, and up to about 20% in the worst cases. The approximate values are higher than the experimental or theoretical results. The intrinsic full energy peak efficiency determined by the analytic expression is compared with experimental results for NaI 1″ × 1″ and 3″ × 3″ with ¹³⁷Cs and ⁶⁰Co sources. Results from Monte Carlo calculations agree within 10% with the determination. These errors are acceptable at the design state, as later both source activity and counting time may be adjusted to yield the required statistical uncertainty.     

The COBRA double-beta decay experiment

The COBRA experiment aims to use a large quantity of Cadmium–Zinc–Telluride (CdZnTe) semiconductor detectors to search for neutrinoless double-beta decay (0υββ). The current status of the experiment is discussed, and new limits on several double-beta modes are presented. Future plans for a large-scale experiment are also described.     

MASS TRANSFER OF SULFUR DIOXIDE TO CONDENSING AQUEOUS AEROSOLS

Sodium chloride aerosols were generated from a 1.0 percent solution and passed through a tubular furnace, then recondensed at 29°C in a cooling section in the presence of SO₂. The dry particles ranged from 0.711 to 0.843 µm and the condensed droplets were in the 1.66 to 2.88 µm range. Final droplet size was varied by controlling the temperature of the nebulizer solution between 17 and 50°C. The SO₂ concentration in the gas phase of the condensing cloud was varied between 0.5x10 - ³ and 2.5 xl0 - ³ atm.

Cloud droplets were separated from the gas stream in a point-to-plane electrostatic precipitator and the droplets analyzed colorimetrically for total sulfur content.

Concentrations of SO₂ in the aqueous phase were about one order of magnitude greater than values obtained from equilibrium constants. The collection rate of SO₂ at 29°C appeared to be first order in SO₂ gas phase concentrations.

A model for this process was constructed, based on the hydrate formation in the gas-water interface[SO₂]_g + n[H₂O]ℓ ⇋ [SO₂ · n(H₂O)]ℓ

The order of the hydrate n was estimated to be 4.0.     

Tungsten alloys as radiation protection materials

The radiation shielding effects of some tungsten alloys were evaluated using ¹³³Ba(356 keV) and ¹³⁷Cs(660 keV)γ-ray sources. Tungsten carbide had about the same effect as the commonly used lead, while tungsten-copper alloy gave as good a performance as tungsten. The results of transmittance measurements for these materials, as well as of their Monte-Carlo simulation, are reported.     

Coincidence timing of Schottky CdTe detectors for tomographic imaging

Schottky CdTe detectors are good candidates for large pixel array imagers. For use of such arrays in Positron Emission Tomography (PET) the coincidence timing of the detectors is very important, since it reduces the background from random coincidences. The coincidence timing of a small 2×2×1 mm³ detector has been measured as 11.6 ns, and thus is not much worse than the timing of BGO scintillators, commonly used in PET.     

Analysis of interface states and series resistance at MIS structure irradiated under Co γ-rays

In this research, we investigated the effect of ⁶⁰Co γ-ray exposure on the electrical properties of Au/SnO₂/n-Si (MIS) structures using current–voltage (I–V) measurements. The fabricated devices were exposed to γ-ray doses ranging from 0 to 300 kGy at a dose rate of 2.12 kGy h⁻¹ in water at room temperature. The density of interface states N_ss as a function of E_c–E_ss is deduced from the forward bias I–V data for each dose by taking into account the bias dependence effective barrier height and series resistance of device at room temperature. Experimental results show that the γ-irradiation gives rise to an increase in the zero bias barrier height Φ_BO, as the ideality factor n and N_ss decrease with increasing radiation dose. In addition, the values of series resistance were determined using Cheung's method. The R_s increases with increasing radiation dose. The results show that the main effect of the radiation is the generation of interface states with energy level within the forbidden band gap at the insulator/semiconductor interface.     

Liquid-Liquid Extraction, Separation, Preconcentration, and ICP-AES Determination of Lanthanum and Cerium with N-Phenyl-(1,2-methanofullerene C60)61-formohydroxamic Acid

A novel method for liquid-liquid extraction, separation, preconcentration, and simultaneous trace determination of cerium(IV) and lanthanum(III) with N-phenyl-(1,2-methanofullerene C₆₀)61-formohydroxamic acid (PMFFA) is reported. Lanthanum and cerium are extracted at pH 8.5 and 9.5, respectively in chloroform and recovered from monazite sands in the presence of thorium, uranium, and large number of cations and anions in high purity (99.98%). The extraction mechanism is investigated. The influence of PMFFA, pH, diverse ions, and temperature on the distribution constants of lanthanum and cerium was examined. The overall stability constants (log β₂K_e) and extraction constants (K_ex) for lanthanum(III) are 22.50 and 5.0 × 10^-9, respectively and for cerium(IV) are 21.51 and 3.9 × 10^-9, respectively. Lanthanum(III) gives a colourless complex with PMFFA which is extracted into chloroform having molar absorptivity 5.5 × 10⁴ L mol^-1 cm^-1 at 395 nm, and Beer's law 0.12-2.52 µg mL^-1, while cerium(IV) forms a red coloured complex, λ_max 460 nm, molar absorptivity 1.5 × 10⁴ L mol^-1 cm^-1, and Beer's law 0.46-9.26 µg mL^-1. For trace determination the extracts were directly inserted into the plasma for inductively coupled plasma atomic emission spectrometry ICP-AES measurements of lanthanum and cerium which increases the sensitivity 60 folds and obey Beer's law in the range, 2.1-37.5 ng mL^-1 for lanthanum and 9.2-186.4 ng mL^-1 for cerium. The method is applied for the determination of lanthanum and cerium in real and standard samples, sea water, and environmental samples.     

Polymer-Based Flexible Schottky Diode Made With Pentacene–PEDOT:PSS

This paper reports a polymer-based flexible Schottky diode made on a flexible cellulose substrate with poly(3, 4-ethylenedioxythiophene):poly(styrenesulfonate)-pentacene (PEDOT:PSS). Pentacene was dissolved into the N-methylpyrrolidone (NMP) solvent and mixed with PEDOT:PSS. Three-layered Schottky diodes consisting of Al, PEDOT:PSS or pentacene-PEDOT:PSS, and Au were fabricated. The current density of Au/PEDOT:PSS/Al Schottky diode (4.8 muA/cm² at 2.5 V/mum) was drastically improved to 440 muA/cm² at 1.9 V/mum when the pentacene-PEDOT:PSS was used. This enhancement of current density of Schottky diode is promising for flexible electronic devices.     

Calculation of efficiency functions in 4π β-γ counting

An attempt is made to calculate an efficiency function applicable to 4πβ-γ coincidence measurements as the first stage of evaluating the order of the polynomial of the fitting function. For this purpose, the β-ray energy spectra and self-absorptions of spherical particle sources are calculated by the Monte Carlo simulation under the continuous slowing down approximation. On the other hand, it is shown that three sets of absorption coefficients and partial intensity ratios corresponding to a β-ray group give analytically the self-absorption for the same particle sources. Finally, we show that the efficiency functions applicable to ⁵⁹Fe and ¹³⁴Cs are easily obtained by using the energy spectra or self-absorptions.     

Influence of a Weak Magnetic Field on Photoconductivity Spectrum of C60 Single Crystal

Comparative research of the excitation photoconductivity spectra (quantum light energy 2-5 eV) of C₆₀ single crystal in and out of magnetic field at the temperature T = 250-350 K has been carried. The spectral evolution at this temperature range is described. It is shown that the spectra changes abrupt at temperature T₁ ∼ 260 K and T₂ ∼ 315 K. An increase in the photoconductivity up to 15% was observed in the magnetic field (B = 0.4 T) within the photon energy range 2.5-4.5 eV. Local photoconductivity peak's appearances in the magnetic field have been proven that the charge transfer excitons take part in a photoconductivity.     

Numerical Study of Air Compressibility During Horizontal Pneumatic Transport

Using numerical simulations, the effect of the compressibility of air on the flow pattern of particles and pressure drop in the presence of particles during horizontal pneumatic transport operating under negative pressure was examined. The length and inside diameter of the pipeline were 30 m and 40 mm, respectively, and the chosen particles (4 mm in diameter) had densities of ρ_p = 1000 and 2000 kg/m³. The mean air velocities at pipe the inlet were U_inlet = 19, 22, and 28 m/s, and the range of the mass flow rate ratios of particle to air, μ, was varied up to 2.0. For a given inlet air velocity, the difference in the flow pattern between compressible and incompressible flow calculation is generally small. For ρ_p = 1000 kg/m³ particles the additional pressure drop in compressible flow increases when μ is above 0.5 and U_inlet is 28 m/s, μ is above 1.3 and U_inlet is 22 m/s, and μ is above 1.5 and U_inlet is 19 m/s. In these cases, the particle flow pattern is homogeneous. For ρ_p = 2000 kg/m³ particles, the pressure drop increases only when μ is above 1.5 and U_inlet is 28 m/s. The difference is not noticeable when the particle flow pattern is heterogeneous. Also, the difference in the additional pressure drop is much larger during homogeneous flow than heterogeneous flow.     

Preparation of polycrystalline CdZnTe thick film Schottky diode for ultraviolet detectors

High resistivity (3 × 10⁹ Ω cm) polycrystalline CdZnTe thick films with thickness of 25 μm–150 μm were grown on SnO₂: F-coated glass substrates by close-spaced sublimation method. The properties of polycrystalline CdZnTe films were studied by XRD, SEM and EDS, respectively. A CdZnTe film Schottky diode detector was also fabricated and investigated using current–voltage and capacitance–voltage methods. The photo-current density of the device was about 1508.69 nA/mm² under light illumination (λ = 260 nm), at an applied negative voltage of 15 V. The results showed that polycrystalline CdZnTe thick film was suitable for application in ultraviolet detectors.     

Position-sensitive superheated-liquid-droplet neutron dosimeter

The one-dimensional (1D) position-sensitive superheated-liquid-droplet dosimeter (SLDD) has been fabricated and tested in the laboratory. The 1D SLDD is fabricated from a 9.525-mm OD, 6.35-mm ID, 20-cm long, Plexiglas-walled tube filled with a mixture of superheated-liquid Freon droplets and host medium glycerol. Washer-shaped piezoelectric acoustic transducers are positioned at both ends of the tube; they determine the number and positions of the acoustic events when the superheated-liquid droplets evaporate upon neutron irradiation. The SLDD is irradiated with the ¹³⁷Cs and ⁶⁰Co γ-sources, as well as ²⁵²Cf neutron source to test for its radiation response and spatial resolution. The SLDD based on the Freon-134a superheated-liquid droplets operating at 20°C and 1 atm is found to be ideal for measuring absorbed neutron dose. This study also proves that the positions of the radiation-induced nucleation acoustic events can be linearly determined from the differences in the transmission times received by the acoustic transducers on the 1D SLDD. The spatial resolution of the neutron depth-dose is 1 mm due the finite response time (1 μs) of the piezoelectric acoustic transducers.     

A Novel Fullerene Hydroxamic Acid for the Liquid-Liquid Extraction, Separation, Preconcentration, and Spectrophotometric and ICP-AES Determination of Vanadium

A new reagent N-phenyl-(1,2 methanofullerene C₆₀)61-formohydroxamic acid (PMFFA) is reported for extraction and trace determination of vanadium(V) in nutritional and biological substrates. The extraction mechanism of vanadium from 6 M HCl media is investigated. The influence of PMFFA, diverse ions, and temperature on the distribution constant of vanadium examined. The over all stability constant (log β₂K_e) and extraction constant (K_ex) are 20.89 ± 0.02 and 8.0 ± 0.02 × 10^-15, respectively in chloroform. The thermodynamics parameters are calculated and kinetics of vanadium transport is discussed. The system obeys Beer's law in the range of 3.2-64.0 ng mL^-1 of vanadium(V). The molar absorptivity is 7.96 × 10⁵ L mol^-1 cm^-1, at 510 nm. The PMFFA-vanadium(V) complex chloroform extract in chloroform was directly inserted into plasma for ICP-AES measurement, which increases the sensitivity by 50 folds and obey Beer's law in the range of 50-1200 pg mL^-1 of vanadium(V). The method is applied for determination vanadium in real standard samples, sea water, and environmental samples.