OFDM闭环发射分集结合自适应功率分配

将自适应功率分配技术应用于多发送多接收天线正交频分复用(MIMO-OFDM)系统,如何在载波和天线间分配能量是个关键问题。该文提出:对不同发射天线的各个子载波采用闭环发射分集方案;接着再进行载波间的功率分配,该算法的目标是使误码率最小。文中用数学方法证明了此方案是使总误码率最小的最佳方案。仿真结果显示:在误码率取0.1%时,对于两根发射天线一根接收天线4个子载波的OFDM系统,与传统的将开环发射分集与OFDM相结合的算法相比,此算法能带来6.5dB的增益。     

基于误码率最小化的V-BLAST系统的最优功率分配

多输入多输出无线通信系统能通过空间复用提供巨大的信道容量。结合自适应技术，从最小化误码率的角度，针对两根发射天线的V-BLAST系统提出了一种新的天线间功率分配方案。所提方案根据信道情况分配各天线的发射功率，减小了误差传播效应带来的影响。仿真结果表明与传统的V-BLAST算法相比，在两发两收V-BLAST系统中，误码率为10^-3时，可获得2dB的信噪比增益，在误码率低于10^-3时，可获得至少1．5dB的信噪比增益。     

基于OFDM的DF多跳通信系统的功率分配

研究了DF多跳OFDM通信系统的功率分配优化.在总发射功率受限的条件下,提出了一种双向优化功率分配算法(D-OPA):先优化单个子载波上各中继节点的功率分配,使该子载波上的信道容量最大;再优化各个子载波间的功率分配,使单跳的信道容量最大,从而最大化系统的信道容量.仿真结果表明:提出的算法与自适应功率分配算法、平均功率分配算法相比,信道容量明显提高.     

OFDM快时变信道下的相位旋转调制技术

由于发射端和接收端振荡器之间的频率偏差以及无线信道的时变性,OFDM系统各个子载波之间的正交性将会被破坏,从而产生载波间干扰(ICI)。该文利用发送端的多天线分集,提出了一种新型的相位旋转调制技术。它通过在频域对不同发送天线上的发送信号进行不同角度的旋转,使接收端等效信道频域响应产生的载波间干扰最小,达到抑制载波间干扰的作用。实验证明,这种新型的相位旋转调制技术不会改变OFDM系统的发送功率,能够在不占用额外系统带宽的情况下有效地消除快时变信道环境下系统的载波间干扰,达到较好的误码率性能。     

红外无线系统的变步长自适应功率分配算法

红外无线通信系统中,为了在功率和误码率一定的限制下进一步提高系统容量,提出了一种新的变步长自适应功率分配算法,该算法以每比特分配功率的代价最小为原则(一次可分配多个比特)来选择最佳的调制技术.分析了其速度原理,并在建立模型的基础上,通过仿真研究了新算法的系统性能,并与理想注水算法以及传统的简单速率量化算法进行比较.仿真...     

混合NOMA/OFDMA可见光通信系统资源分配算法

为了进一步降低混合非正交多址/正交频分复用多址（NOMA/OFDMA）技术的多用户多小区可见光通信系统的误码率,提出了一种功率和子载波的联合分配算法。该算法以最小化系统误符号率为优化目标,实现了子小区间载波和用户功率的联合最优分配。首先,理论推导出系统的误符号率表达式;然后,使用Matlab软件进行仿真,模拟可见光通信系统模型,并借助遗传算法得到最优的分配结果;最后,将该算法与现有的算法进行了对比。仿真结果表明,所提算法的误符号率性能更优。     

多用户OFDM系统中一种新颖的自适应功率分配方案

针对多用户正交频分复用(OFDM)系统自适应资源分配的问题,提出了一种新的自适应子载波分配方案。子载波分配中首先通过松弛用户速率比例约束条件确定每个用户的子载波数量,然后对总功率在所有子载波间均等分配的前提下,按照最小比例速率用户优先选择子载波的方式实现子载波的分配;在功率分配中提出了一种基于人工蜂群算法和模拟退火算法(ABC-SA)相结合的新功率分配方案,并且通过ABC-SA算法的全局搜索实现了在所有用户之间的功率寻优,同时利用等功率的分配方式在每个用户下进行子载波间的功率分配,最终实现系统容量的最大化。仿真结果表明,与其他方案相比,所提方案在兼顾用户公平性的同时还能有效地提高系统的吞吐量,进而证明了所提方案的有效性。     

组播OFDM系统中基于子载波成对调整的功率分配算法

 研究了在总功率的约束下,组播OFDM系统中最大化组播速率的功率分配问题. 首先引入贪婪算法求解该问题以降低复杂度,但贪婪算法只执行预设的固定次数分配后即停止,其截止条件与功率分配过程中的状态无关,无法有效地提高系统性能;进而提出了两种基于子载波成对调整的功率分配算法,在初始功率分配的基础上选择子载波对交换功率,将功率重新分配给能够使组播速率提高得最多的子载波,并只在无法进一步提高组播速率时才停止调整. 研究和仿真结果表明,所提出的两种调整算法能够有效地提高组播速率,性能接近根据凸函数优化方法求得的最优解,且显著降低了算法的复杂度.     

一种基于子载波合并的多播资源调度算法

针对无线OFDM多播系统,该文提出一种基于子载波合并的多播资源调度算法。该算法通过提前将子载波分组,避免了不必要的子载波配对;自适应地选择子载波合并\非合并,在分集和复用两种模式中选取最优方案;同时根据子载波功率分配的特点,将其解耦为配对子载波集合内功率分配和集合间功率分配两个子问题,进一步优化了算法性能。仿真结果表明,与现有方案相比,所提方案能够在复杂度较低的情况下,较好地提升系统性能。     

改进的多载波CDMA系统性能分析

多载波CDMA技术能够提供大的系统容量、对抗瑞利衰落和消除符号间干扰等优点,成为具有发展前景的调制技术之一。本文基于各用户服务指标(QoS)的不同,提出了一种自适应子载波分配的改进的多载波CDMA系统。通过在衰落信道下的仿真,结果表明:采用本文提出的自适应子载波分配算法的改进MC—CDMA系统较之传统的MC-CDMA系统的误码率性能有了较大程度的改善。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.