Effect of magnesium content on the stress exponent and effective stress in the steady state creep of Al-Mg alloys

The stress exponent of steady state creep,n, and the internal ( _i) and effective stresses ( _e) have been determined using the strain transient dip test for a series of polycrystalline Al-Mg alloys creep tested at 300° C and compared with previously published data. The internal or dislocation back stress, _i, varied with applied stress,, but was insensitive to magnesium content of the alloy, being represented by the empirical equation _i=1.084 ^1.802. Such an applied stress dependence of _i can be explained by using an equation for _i of the form _i (dislocation density)^1/2 and published values for the stress dependence of dislocation density. Values of the friction stress, _f, derived using the equation _e/=(1–c) (1– _f/), indicate that _f is not dependent on the magnesium content. A constant value of _f can best be rationalized by postulating that the creep dislocation structure is relatively insensitive to the magnesium content of the alloy.On leave from Engineering Materials Department, University of Windsor, Windsor, Ontario N9B 3P4, Canada.     

On internal stress and activation volume in polymers

The two-site model is developed for the analysis of stress relaxation data. It is shown that the product of d In (– )/d and (- _i) is constant where is the applied stress, _i is the (deformation-induced) internal stress and = d/dt. The quantity d In ( )/d is often presented in the literature as the (experimental) activation volume, and there are many examples in which the above relationship with (- _i) holds true. This is in apparent contradiction to the arguments that lead to the association of the quantity d In (– )/d with the activation volume, since these normally start with the premise that the activation volume is independent of stress. In the modified theory presented here the source of this anomaly is apparent. Similar anomalies arise in the estimation of activation volume from creep or constant strain rate tests and these are also examined from the standpoint of the site model theory. In the derivation presented here full account is taken of the site population distribution and this is the major difference compared to most other analyses. The predicted behaviour is identical to that obtained with the standard linear solid. Consideration is also given to the orientation-dependence of stress-aided activation.     

Distribution characteristics of mechanical properties and correlation between the respective properties on S35C carbon steel

Mechanical properties of tensile strength, , upper yield stress, _SU, lower yield stress, _SL elongation, , area reduction, , Vickers hardness, H _v, and impact absorbed energy, E, were examined using 50 specimens of S35C carbon steel, which were machined from two bars supplied from the same charged and heat-treated material. Distribution characteristics of these properties are discussed, and the correlation between each pair of them is investigated from a statistical viewpoint. The main conclusions obtained are summarized as follows; distribution characteristics of _B, _SL, , , H _v and E are well approximated by a normal distribution, but those of asu are not approximated as well by this type of distribution. In the latter case, a Weibull distribution is preferable to represent the distribution pattern. No significant correlation was observed between each pair of the above mechanical properties. Consequently, individual properties have the inherent distribution characteristics independent of the other properties.     

Application of a new iterative method for elastic-plastic stress analysis

A new iterative method for elastic-plastic stress analysis based on a new approximation of the constitutive equations is proposed and compared with standard methods on the accuracy and the computational time in a test problem. The proposed method appears to be better than the conventional methods on the accuracy and comparable with others on the computational time. Also the present method is applied to a crack problem and the results are compared with experimental ones. The agreement of both results are satisfactory.List of symbols u = (u ₁, u ₂) displacements u ^(H) = u ⁽ⁿ⁺¹⁾ - u ⁽ⁿ⁾ u _k ⁽ⁿ⁾ = u _(k ^{(n + 1)} - u ⁽ⁿ⁾ (n, k = 0, 1, 2, ...) - = ₁₁, ₂₂, ₁₂) stresses - = (₁₁, ₂₂, ₁₂) strains - = (₁₁, ₂₂, ₁₂) center of yield surface - D elastic coeffficient matrix, C = D ^–1 - von Mises yield function. The initial yielding is given by f() = _Y - f {f/} - ^* transposed f - H hardening parameter (assumed to be a positive constant for kinematic hardening problems) - time derivative of - [K] total elastic stiffness matrix - T traction vector - = [B] relation between nodal displacements and strains     

The influence of antimony-additions on the creep behaviour of a 25wt% Cr-20wt% Ni austenitic stainless steel

The effect of antimony on the creep behaviour (dislocation creep) of a 25 wt% Cr-20 wt% Ni stainless steel with ~ 0.005 wt% C was studied with a view to assessing the segregation effect. The antimony content of the steel was varied up to 4000 ppm. The test temperature range was 1153 to 1193 K, the stress range, 9.8 to 49.0 MPa, and the grain-size range, 40 to 600m. The steady state creep rate, , decreases with increasing antimony content, especially in the range of intermediate grain sizes (100 to 300m). Stress drop tests were performed in the secondary creep stages and the results indicate that antimony causes dislocations in the substructure to be immobile, probably by segregating to them, reducing the driving stress for creep.Nomenclature _a Creep stress in a constant load creep test without stress-drop - _A Initial applied stress in stress-drop tests - Stress decrement - ( _A-) Applied stress after a stress decrement, - t _i Incubation time after stress drop (by the positive creep) - _C Strain-arrest stress - _i Internal stress - _{s s}-component (= _i- _c) - Steady state creep rate (average value) in a constant load creep test - Strain rate at time,t, in a constant load creep test - New steady state creep rate (average value) after stress drop from _A to ( _A-) - Strain rate at time,t, after stress drop.     

Influence of threshold parameters on cleavage fracture predictions using the Weibull stress model

This study explores applications of three-parameter Weibull stress models to predict cleavage fracture behavior in ferritic structural steels tested in the transition region. The work emphasizes the role of the threshold parameters (_th and _{w – min}) in cleavage fracture predictions of a surface crack specimen loaded predominantly in tension for an A515-70 pressure vessel steel. A recently proposed procedure based upon a toughness scaling methodology using a modified Weibull stress (^* _w) extends the calibration scheme for the Weibull modulus, m, to include the threshold parameters. The methodology is applied to calibrate the Weibull stress parameter for the tested material and then to predict the toughness distribution for the surface crack specimen. While the functional relationship between ^* _w and m suggests a strong effect of the threshold stress, _th, on the calibrated m-parameter, the results show a remarkably weak dependence of fracture predictions on _th as does the dependence of fracture predictions on _w–min for this specimen.     

Interfacial debonding and fibre pull-out stresses

Based on a theoretical model developed previously by the authors in Part II of this series for a single fibre pull-out test, a methodology for the evaluation of interfacial properties of fibre-matrix composites is presented to determine the interfacial fracture toughness G _c, the friction coefficient , the radial residual clamping stress q _o and the critical bonded fibre length z _max. An important parameter, the stress drop , which is defined as the difference between the maximum debond stress _d ^* and the initial frictional pull-out stress _fr, is introduced to characterize the interfacial debonding and fibre pull-out behaviour. The maximum logarithmic stress drop, In(), is obtained when the embedded fibre length L is equal to the critical bonded fibre length z _max. The slope of the In()-L curve for L bigger than z _max is found to be a constant that is related to the interfacial friction coefficient . The effect of fibre anisotropy on fibre debonding and fibre pull-out is also included in this analysis. Published experimental data for several fibre-matrix composites are chosen to evaluate their interfacial properties by using the present methodology.On leave at the Department of Mechanical Engineering, Hong Kong University of Science and Technology, Clear Water Bay, Hong Kong.     

Methodology for the determination of the interfacial properties of brittle matrix composites

The interfacial properties of a glass-ceramic matrix composite (SiC/CAS) were determined from single-fibre push-out tests using the interfacial test system. The coefficient of friction, , the residual clamping stress, _c, and fibre axial residual stress, _z , were extracted by fitting the experimental stress versus fibre-end displacement curves using the models of Hsueh, and Kerans and Parthasarathy. Using Hsueh's model, the intrinsic interfacial frictional stress (=_c) was found to be 11.1±3.2 MPa, whereas by using Kerans-Parthasarathy's model it was found to be 8.2±1.5 MPa. Comparisons between these models are included, together with a discussion of data analysis techniques.Nomenclature _z Axial fibre residual stress (Pa) - ^* Effective clamping stress (Pa) - _c Residual clamping stress (Pa) - _p Poisson's effect-induced clamping stress (Pa) - _d ⁰ Debond stress in the absence of residual stresses (Pa) - _d Experimental debond stress (Pa) - Compressive applied stress (Pa) - Interfacial shear stress (Pa) - u Fibre-end displacement (m) - h Debond length (m) - r Fibre radius (m) - E _f Fibre Young's modulus (Pa) - E _m Matrix Young's modulus (Pa) - v _f Fibre Poisson's ratio (dimensionless) - v _m Matrix Poisson's ratio (dimensionless) - f Fibre volume fraction (dimensionless) - k Parameter (dimensionless) - D Parameter (dimensionless) - Interfacial coefficient of friction (dimensionless) - G _i Interface toughness (J m^–2) - C _m Load-train compliance (m N^–1)     

Convection in a shallow laterally heated cavity with conducting boundaries

Shallow cavity flows driven by horizontal temperature gradients are analysed over a range of Rayleigh numbersR and Prandtl numbers , whereR is comparable in size to the aspect ratioL(1). Eigenvalue calculations show the existence of a critical Prandtl number R > R _c (), below which the parallel core-flow structure is destroyed for Rayleigh numbersR>R _c(). For other Rayleigh numbers and Prandtl numbers the horizontal scale of influence of the end walls of the cavity is determined.     

A modified Weibull treatment for the analysis of strength-test data from non-identical brittle specimens

Powder compacts (e.g., pharmaceutical tablets) manufactured on commerically available machines are not strictly identical but show inevitable variability in their weights, thicknesses and compaction pressures. Consequently, the variability in fracture-stress data obtained from such brittle specimens is greater than that due to the inherent strength variability of the material itself. A modified Weibull analysis has been developed so that a more accurate estimate of the inherent variability of the mechanical strength of the material can be derived from test data obtained from commercially produced compacts; its application is illustrated.Nomenclature D diameter - f() relative frequency of occurrence of specimens with density and volume - F minimization function - i ascending rank number of a fracture stress - m Weibull modulus - N _tot number of specimens in a batch - N() number of specimens with densities in the range to + d and volumes in the range to + d - P _f failure probability - p _u upper punch compaction pressure - t thickness - volume - w weight - W _f fracture load - density - _f fracture stress - ¯ _f mean fracture stress of a batch - ¯ _f() mean fracture stress of specimens with density and volume - ₀ scale parameter or normalizing factor - _u location parameter or threshold stress     

Statistical analysis of the Hertzian fracture of pyrex glass using the Weibull distribution function

Hertzian fracture tests were carried out on specimens of ground-and-polished Pyrex glass using polished Pyrex glass balls of 6 and 8 mm diameter. The results were analysed according to the theory of flaw statistics originally proposed by Weibull. The Weibull parameters m and ₀ were found to be independent of ball size; _u however decreased with increase in ball size. The parameters _u,₀ and m obtained from the Hertzian tests differed from those obtained from a four-point bend test. The predicted mean fracture stress and the mean fracture location for Hertzian fracture using the derived Weibull parameters agreed reasonably well with the experimental values.     

Charged defects-controlled conductivity in Ge-ln-Se glasses

The variation of the d.c. electrical conductivity, , with composition and temperature was investigated for glasses of the Ge-In-Se system. The results indicate a decrease in the activation energy for electrical conductivity, E, and an increase in on introduction of indium into Ge-Se glasses. The changes in E and with composition (selenium content in the glasses) are identical for the Ge_x In₅ Se_95–x and Ge_x In₈Se_92–x families. The results have been traced to the conduction controlled by charged defects in these chalcogenide glasses. The changes in E and have been explained by a shift in the Fermi level, being brought by the introduction of indium.     

Pyramidal yield criteria for epoxides

The tensile, compressive and shear yield strengths of two epoxides were measured under superposed hydrostatic pressure extending to 300 MN m^–2. For both materials, the ratio of the moduli of the tensile, _T, to compressive, _C, yield stress at atmospheric pressure was approximately 34, as has been reported previously for a number of thermoplastics. The ₂= ₃ envelope in stress space was plotted according to these two-parameter ( _C and _T) yield criteria: conical, paraboloidal and pyramidal; the best correlation was with the last. The experimental tensile and compressive data for tests under pressure, however, fit slightly better two straight lines which are consistent with a three-parameter single hexagonal pyramidal yield surface. For plane stress and shear under pressure yield envelopes of these surfaces, the correlation with experimental data is again best for the pyramidal criteria, except for biaxial or triaxial tension when these resins are brittle. The third independent parameter employed in the pyramidal criterion was the equi-biaxial compressive yield stress, determined by tensile experiments under appropriate superposed hydrostatic pressure; alternatively plane strain compressive yield stress, _PC, may be used.     

On the measurement and physical meaning of the cleavage fracture stress in steel

Elastic-plastic two-dimensional (2D) and three-dimensional (3D) finite element models (FEM) are used to analyze the stress distributions ahead of notches of four-point bending (4PB) and three-point bending (3PB) specimens with various sizes of a C-Mn steel. By accurately measuring the location of the cleavage initiation sites, the local cleavage fracture stress _f and the macroscopic cleavage fracture stress _F is accurately measured. The _f and _F measured by 2D FEM are higher than that by 3D FEM. _f values are lower than the _F, and the _f values could be predicted by _f=(0.8––1.0)_F. With increasing specimen sizes (W,B and a) and specimen widths (B) and changing loading methods (4PB and 3PB), the fracture load P _f changes considerably, but the _F and _f remain nearly constant. The stable lower boundary _F and _f values could be obtained by using notched specimens with sizes larger than the Griffiths–Owen specimen. The local cleavage fracture stress _f could be accurately used in the analysis of fracture micromechanism, and to characterize intrinsic toughness of steel. The macroscopic cleavage fracture stress _F is suggested to be a potential engineering parameter which can be used to assess fracture toughness of steel and to design engineering structure.     

Effect of shot peening on the fatigue and fracture behaviour of two titanium alloys

The fatigue and fracture behaviour of two titanium alloys, the near-alpha IMI-685 and alpha-beta IMI-318, were studied in the machined and polished (MP) as well as the machined, polished and shot (glass-bead) peened (MPS) conditions. Glass-bead peening reduced the room-temperature as well as the high-temperature (450°C) fatigue life of alloy IMI-685 at high stress amplitudes, _a, approaching the proof stress, _ps, of the material (LCF region). When the applied stress amplitude (0–770 MPa, HCF region) was comparable to the peen-induced peak longitudinal residual stress, _LP, i.e. (_LP/a)=0.92, an improvement in the room-temperature fatigue life of IMI-685 was observed. When the (_LP/a) ratio was less than this value, decreases in the fatigue life were seen. The room-temperature fatigue behaviour of IMI-318 at high stress amplitudes was similar to that of IMI-685. The decrease in the fatigue life of this alloy, at a stress amplitude (770 MPa) where improvement was observed for IMI-685, could be attributed to the higher relaxation of peen-induced residual stresses in IMI-318 compared with IMI-685. Glass-bead peening improved the hightemperature (450°C) fatigue life of IMI-685 at a low stress amplitude (465 MPa; (_a/PS)=0.87). The crack-initiation sites in the MP and the MPS conditions were at the surface for both the alloys. However, fracture in the surface layers of the alloys appeared more brittle in the peened (MPS) rather than in the unpeened (MP) condition.     

The dielectric behaviour of single-crystal MgO,Fe/MgO and Cr/MgO

The dielectric constants and loss factors,, for pure single-crystal MgO and for Fe-and Cr-doped crystals have been measured at frequencies, , from 500 Hz to 500 kHz at room temperature. For pure MgO at 1 kHz the values of and the loss tangent, tan , (9.62 and 2.16×10^–3, respectively) agree well with the data of Von Hippel; the conductivity, , varies as ⁿ withn=0.98±0.02. In Fe-doped crystals increases with Fe-concentration (at any given frequency); for a crystal doped with 12800 ppm Fe, was about four times the value for pure MgO. At all concentrations the variation of log with log was linear andn=0.98±0.02. A decrease in with increasing Fe-concentration was also observed. A similar, although less pronounced, behaviour was found in Cr-doped crystals. The effects are discussed in terms of hopping mechanisms.     

Electrical conductivity,thermoelectric power and dielectric constant of NiWO4

The a.c. electrical conductivity ( _ac), thermoelectric power () and dielectric constant () of antiferromagnetic NiWO₄ are presented. _ac and have been measured in the temperature range 300 to 1000 K and in the temperature range 600 to 1000 K. Conductivity data are interpreted in the light of band theory of solids. The compound obeys the exponential law of conductivity = ₀ exp (–W/kT). Activation energy has been estimated as 0.75eV. The conductivity result is summarized in the following equation =2.86 exp (–0.75 eV/kT)^–1 cm^–1 in the intrinsic region. The material is p-type below 660 K and above 950 K, and is n-type between 660 and 950 K.     

Transport results from untwinned YBCO: Washboard frequency of the vortex lattice,and the quasiparticle mean free path

The washboard frequency of the moving vortex lattice in untwinned YBa₂ Cu₃ O_6.93 may be observed through mode-locking to an externally applied ac current of frequency _ext. The interference between and _ext results in jumps in the dc current-voltage characteristics when and _ext are harmonically related¹. The interference effect disappears in the vortex liquid state. The Hall conductivity _xy below T_c in YBCO contains contributions² from a positive quasiparticle (qp) term (H) and a negative vortex term (1/H). The qp term is surprisingly large well below T_c and implies a large gap anisotropy and a long qp mean free path (mfp). The thermal Hall effect³ _xy is closely related to the qp _xy; _xy is produced by asymmetric scattering of qp by pinned vortices. The qp mfp at H = 0, extracted from _xy and extended to low T by _xy, increases remarkably from 90 Å at T_c to more than 0.5m at 22 K.     

Ionic and electronic conductivity in some simple lithium salts

The electrical conductivity () and thermoelectric power (S) of Li₃VO₄, Li₃PO₄ and Li₃BO₃ solidified melts are presented in the temperature range from 415 K to the melting point of each solid. The ionic ( _i,) and electronic ( _e) contributions to have been separated over the entire temperature range with the help of a time-dependence study of the d.c. electrical conductivity. Superionic phases in all three solids have been observed below their melting points in which the conductivity is almost purely ionic. The value of the phase transition temperature below which the solid transforms from superionic to normal phase has been obtained. It has been shown that in the normal phase, these solids are mixed conductors. Data for the temperature variations of both _i, and _e are also presented and discussed.     

Surface tension of helium at the superfluid critical end-point

The singularity in the vapor-liquid interfacial tension, (T), of helium at the transition to superfluidity is analyzed theoretically. The universal amplitude ratio R ⁺ =K₊( ₀ ⁺ )^d–1/k _B T , where K₊ and K_– are the amplitudes of the |T–T|^µ singularity in , with =1.34 ₃ , is known from recent work to first order in =4–d for the general n-vector model in d dimensions. Extrapolation to d=3 for n=2 indicates R ⁺ =0.05–0.08, which is shown to be consistent with the experimental data. Further analysis of the experiments establishes that the universal ratio Q=K₊/K _– exceeds 0.35, and is consistent with the recent prediction Q0.9; this demonstrates the inadequacies of earlier theoretical treatments. The existence in the observed surface tension of an anomalous, negative contribution of unknown origin at a few millikelvin beneath T is stressed.