Distribution of acrylic acid grafted chains introduced into polyethylene film by simultaneous radiation grafting with water and ethanol as solvents

The graft copolymerization of acrylic acid onto low‐density polyethylene films by simultaneous γ‐ray irradiation was carried out. The effect of water and ethanol as grafting solvents on the distribution of grafted poly (acrylic acid) in the low‐density polyethylene films was studied with optical microscopy observations of dyed and sliced samples and attenuated total reflection/Fourier infrared spectroscopy analysis. When no vigorous homopolymerization occurred, both polyethylene and poly(acrylic acid) existed in the grafted layer, and the thickness of the grafted layer and the poly(acrylic acid) concentration in the grafted layer increased with an increasing degree of grafting, regardless of the grafting conditions, the former increasing faster than the latter. In comparison with water as the solvent, in the absence of the inhibitor, homopolymerization could be suppressed to a certain degree in the ethanol solvent system, whereas in the presence of the inhibitor, obvious homopolymerization occurred at a lower monomer concentration, and both the degree of grafting and the thickness of the grafted layer were lower. Such differences could be explained by the chain transfer and the relatively low solubility of poly(acrylic acid) in ethanol. In addition, an experimental scheme using optical microscopy to observe the dyed and sliced polymers was optimized. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1570–1577, 2007     

Synthesis and characterization of polyethylene modified through phase‐transfer‐catalyzed graft copolymerization

In an effort to impart biodegradability, polyethylene (PE) was modified through the graft copolymerization of vinyl monomers such as acrylamide (AAm) and acrylic acid (AAc) by a phase‐transfer‐catalyst method. The grafting percentage of AAm and AAc for PE was found to be dependent on the dibenzoyl peroxide concentration, monomer concentration, time, temperature, and concentration of the phase‐transfer catalyst. Some AAm‐ and AAc‐grafted PE samples were prepared by chemical, UV, and γ‐radiation methods. The biodegradation of samples of PE, polyethylene‐g‐polyacrylamide, and polyethylene‐g‐poly(acrylic acid) prepared by all these methods was studied. The weight loss of the samples over a period of time was observed with soil‐burial tests. The grafted samples prepared by the phase‐transfer‐catalyst method showed better biodegradation results than those prepared by other methods of grafting. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Chemical grafting of aniline and o‐toluidine onto poly(ethylene terephthalate) fiber

Graft copolymerization of poly(aniline) and poly(o‐toluidine) onto poly(ethylene terephthalate) fiber was conducted by using peroxydisulfate as a lone initiator under nitrogen atmosphere at various experimental conditions in aqueous hydrochloric acid medium. The grafting of poly(aniline) and poly(o‐toluidine) onto poly(ethylene terephthalate) fiber was verified by recording cyclic voltammetry of the grafted fiber, conductivity measurements, and thermal analysis. Graft parameters—such as % grafting, % efficiency, and the rate of grafting—were followed. Grafting was always accompanied by homopolymerization. The rate of homopolymerization was also followed in all experimental conditions. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 121–128, 1999     

Grafting of poly(acrylic acid) onto cellulosic microfibers and continuous cellulose filaments and characterization

Results from the grafting of poly(acrylic acid) (PAA) onto cellulosic microfibers and continuous cellulose filaments are presented. The grafting of PAA onto cellulosic fibers offers the possibility of developing enhanced ion exchange and fluid absorbency on the fibers. The grafting of PAA was carried out with a two‐step procedure. First, vinyl‐terminated ethoxy silane was deposited on the surface of the fiber. This was followed by a grafting polymerization reaction in aqueous media of acrylic acid with different concentrations of potassium persulfate (KPS), which acted as the initiator. The percentage of grafting increased with increasing KPS concentration and reached a maximum value at a concentration of about 0.4 wt % with respect to the weight of the fiber. The grafted copolymer was characterized by Fourier transform infrared spectroscopy. Strong evidence that the grafting reaction was successful was given by the presence of a band, with a maximum at 1732 cm^?1, that was characteristic of carbonyl group absorption and was not initially present in the cellulosic fibers. The water absorption of the cellulosic microfibers grafted with PAA was three times greater than the water absorption of the nongrafted microfibers. The mechanical properties of continuous cellulose filaments did not change drastically with PAA grafting. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 386–393, 2002     

Dialysis membranes from polyethylene films grafted with acrylic acid

Low‐density polyethylene‐g‐poly(acrylic acid) membranes were prepared by the direct radiation grafting of aqueous acrylic acid solutions (containing Mohr's salt) onto low‐density polyethylene films and were irradiated at two different irradiation doses (2 and 3 Mrad) at a dose rate of 0.02 Mrad/h. Two series of polyethylene‐g‐poly(acrylic acid) membranes with 100 and 150% grafting were obtained. The free carboxylic acid groups in the grafted films were converted into the corresponding acrylates by reactions with different metal salts. The swelling (water uptake) and dialysis permeability of glucose and urea through the grafted membranes in different metal‐ion forms were investigated. The prepared membranes showed good permeability to both solutes, which increased as the hydrophilicity of the membrane increased. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 10–14, 2004     

Control of biodegradability of poly(3‐hydroxybutyric acid) film with grafting acrylic acid and thermal remolding

Radiation‐induced graft polymerization of acrylic acid (AAc) on poly(3‐hydroxybutyric acid) (PHB) film was carried out and the resulting film was thermally‐remolded. The PHB films grafted with AAc (PHB‐g‐AAc) having a degree of grafting higher than 5% completely lost the enzymatic degradability. The enzymatic degradability of the grafted film was recovered by thermal remolding. The highest enzymatic degradation rate was observed at degree of grafting of 10% after thermal remolding. The PHB‐g‐AAc films and thermally‐remolded PHB‐g‐AAc films were characterized by contact angle and differential scanning calorimetry. The enzymatic degradability of PHB‐g‐AAc films was lost by the grafted AAc, which covered the surface of PHB film. The acceleration of enzymatic degradation in the remolded PHB‐g‐AAc films was mainly caused by decrease of crystallinity of PHB by dispread of grafted AAc during thermal remolding. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3856–3861, 2006     

Low protein fouling polypropylene membrane prepared by photoinduced reversible addition‐fragmentation chain transfer polymerization

In this study, 2‐hydroxyethyl methacrylate and N‐isopropyl acrylamide was block grafted onto the polypropylene macroporous membrane surface by photo‐induced reversible addition‐fragmentation chain transfer (RAFT) radical polymerization with benzyl dithiobenzoate as the RAFT agent. The degree of grafting of poly(2‐hydroxyethyl methacrylate) on the membrane surface increased with UV irradiation time and decreased with the chain transfer agent concentration increasing. The poly(2‐hydroxyethyl methacrylate)‐ grafted membranes were used as macro chain transfer agent for the further block graft copolymerization of N‐isopropyl acrylamide in the presence of free radical initiator. The degree of grafting of poly(N‐isopropyl acrylamide) increased with reaction time. Furthermore, the poly(2‐hydroxyethyl methacrylate)‐ grafted membrane with a degree of grafting of 0.48% (wt) showed the highest relative pure water flux and the best antifouling characteristics of protein dispersion. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Radiation grafting of acrylic acid/N‐vinyl pyrrolidone binary mixture onto poly(ethylene terephthalate) fabric and growth of human mesenchymal stem cell

Radiation grafting of acrylic acid (AA)/N‐vinyl pyrrolidone (NVP) binary mixture onto poly(ethylene terephthalate) (PET) knittings was investigated by preirradiation technique. The influence of the grafting conditions, such as monomer composition, reaction temperature, and the effect of storage time with temperature after irradiation on the degree of grafting was determined. ATR‐FTIR spectroscopy analysis of the grafted knittings confirmed the existence of amide group of NVP in the knittings. The concentration of peroxides and effect of storage time on peroxide concentration were also determined by 2,2‐Diphenyl‐1‐picrylhydrazyl at different temperatures. There was an increase in surface roughness of grafted PET in comparison to virgin PET as determined by atomic force microscopy and scanning electron microscopy. The grafted knittings were subsequently immobilized with collagen Type I which was further apt for the study of growth and morphology of human mesenchymal stem cell (hMSC). The immobilization of collagen on PET knittings has provided an excellent surface for the growth of hMSCs. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Adhesion of polyethylene plates photografted with methacrylic acid and acrylic acid with enzymatically modified chitosan solutions and X‐ray photoelectron spectroscopy analysis of failed surfaces

An investigation was carried out on the application of dilute chitosan solutions modified by a tyrosinase‐catalyzed reaction with 3,4‐dihydroxyphenetylamine (dopamine) to the adhesion of low‐density polyethylene (LDPE) and high‐density polyethylene (HDPE) plates photografted with carboxyl‐group‐containing hydrophilic monomers, such as methacrylic acid (MAA) and acrylic acid (AA). In the case where photografting was carried out at lower monomer concentrations or at lower temperatures, the adhesive strength sharply increased with lower grafted amounts. A sharp increase in the adhesive strength was found to be due to the formation of shorter grafted polymer chains at lower monomer concentrations and/or the restriction of the location of grafting to the outer surface region at lower temperatures. In addition, the adhesive strength also sharply increased at even lower grafted amounts for photografting onto the HDPE plates and/or that of AA because the location of grafting was restricted to the outer surface region. For the AA‐grafted LDPE and HDPE plates, substrate breaking was observed. This was attributed to the coverage of the substrate surfaces with grafted poly(acrylic acid) chains at lower grafted amounts and a high water absorptivity of the grafted layer. X‐ray photoelectron spectroscopy (XPS) analysis of the grafted LDPE plates incubated in a dopamine solution containing tyrosinase suggested that the increase in the adhesive strength was caused by the penetration of enzymatically modified chitosan solutions in the grafted layers and the subsequent reaction of quinone derivatives enzymatically generated with grafted polymer chains. In addition, the surface analysis of the failed surfaces by XPS showed that as the adhesive strength increased, the location of failure was shifted from the interface between the layers mixed with enzymatically modified chitosan materials and grafted polymer chains to the inside the grafted layer containing enzymatically modified chitosan materials. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Surface initiated ATRP of acrylic acid on dopamine‐functionalized AAO membranes

A facile method for surface‐initiated atom transfer radical polymerization (ATRP) on the anodic aluminum oxide (AAO) membranes has been developed. The AAO membrane was firstly functionalized by poly(dopamine), the bromoalkyl initiator was then immobilized on the poly(dopamine) functionalized AAO membrane surface in a two‐step solid‐phase reaction, followed by ATRP of acrylic acid in a aqueous solution. The poly(acrylic acid) (PAAc)‐grafted AAO membranes were characterized by X‐ray photoelectron spectroscopy, fourier transform infrared spectroscopy and scanning electron microscopy. The XPS and FTIR results indicated that PAAc was successfully grafted on the AAO membrane surface. The degree of grafting increases linearly with the increase of monomer concentration, and it reaches a plateau when the reaction time up to 4 h. The results indicate that the thickness of the grafted polymer inside the isocylindrical pores of AAO membranes could be well controlled by changing the reaction time and monomer concentration. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Formation of multilayer poly(acrylic acid)/poly(vinylidene fluoride) composite membranes for pervaporation

Dual‐ and multilayer composite membranes, consisting of poly(acrylic acid) (PAA) and poly(vinylidene fluoride) (PVDF), were synthesized by the plasma‐induced polymerization technique. The dual‐layer membrane had a dense PAA layer grafted onto a microporous PVDF substrate, whereas in the multilayer membranes, the grafted PAA and the PVDF layers were arranged in an alternating sequence (e.g., PAA/PVDF/PAA and PAA/PVDF/PAA/PVDF/PAA). These membranes were used in a pervaporation process to separate ethanol–water solutions. For the dual‐layer membranes, the results indicated that the separation factor increased and the permeation flux decreased with increasing amounts of grafted PAA. For the case of grafting yield < 0.6 mg/cm², the composite membrane demonstrated poor separation. As the grafting yield reached 0.85 mg/cm², a sharp increase of the separation factor was observed. For the multilayer membranes, the pervaporation performances were very good, with high separation factors (on the order of 100) and reasonable permeation fluxes over a wide ethanol concentration range. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2266–2274, 2004     

Distribution of grafted poly(acrylic acid) in polyethylene film

The morphology of acrylic acid-grafted high-density polyethylene film and the distribution of poly(acrylic acid) in grafted film are examined. The grafting was carried out in the acrylic acid aqueous solution with or without Mohr's salt (an inhibitor of homopolymerization) by preirradiation method. It has become clear that without Mohr's salt the grafted poly(acrylic acid) layer is formed on the surface of the film, while in the presence of Mohr's salt the grafting layer consisting both of poly(acrylic acid) and polyethylene is formed on the inside of the surface.     

Irradiation grafting of methyl methacrylate monomer onto ultra‐high‐molecular‐weight polyethylene: An experimental design approach for improving adhesion to bone cement

The grafting of methyl methacrylate (MMA) onto ultra‐high‐molecular‐weight polyethylene (UHMWPE) and chromic acid etched UHMWPE was conducted with a preirradiation method in air in the presence of a Mohr salt and sulfuric acid. The grafted samples were characterized by Fourier transform infrared (FTIR) spectroscopy, a gravimetric method, differential scanning calorimetry, scanning electron microscopy (SEM), and interfacial bonding strength measurements. The FTIR results showed the presence of ether and carbonyl groups in the MMA‐grafted UHMWPE (MMA‐g‐UHMWPE) samples. The Taguchi experimental design method was used to find the best degree of grafting (DG) and bonding strength. The efficient levels for different variables were calculated with an analysis of variance of the results. SEM micrographs of MMA‐g‐UHMWPE samples showed that with increasing DG and chromic acid etching, the MMA‐g‐UHMWPE rich phase increased on the surface; this confirmed the high interfacial bonding strength of the grafted samples with bone cement. The grafting of the MMA units onto UHMWPE resulted in a lower crystallinity, and the crystallization process proceeded at a higher rate for the MMA‐g‐UHMWPE samples compared to the initial UHMWPE; this suggested that the MMA grafted units acted as nucleating agents for the crystallization of UHMWPE. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Gentamicin‐loaded poly(acrylic acid)‐grafted cotton fibers,part 1: Synthesis,characterization, and preliminary drug release study

This study describes preparation of poly (acrylic acid)‐grafted cotton fibers and release of antibiotic drug gentamicin sulfate from them under physiological conditions. Poly(acrylic acid) has been grafted onto cellulose backbone of cotton fibers via Ce(IV)‐initiated polymerization in aqueous medium. The conditions obtained for optimum grafting were as follows: initiation time 30 min; initiation temperature 37°C; monomer concentration 27.8 mM; grafting temperature 30°C; nitric acid (catalyst) concentration 0.1M. The grafted fibers were characterized by FTIR, TGA, and SEM analysis. The antibiotic drug gentamicin sulfate (GS) was loaded into the grafted fibers by equilibration method and release was studied under physiological conditions. The kinetic release data was interpreted by first‐order kinetic model. Finally, drug‐loaded fibers showed fair antibacterial action against Escherichia coli. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of a poly(acrylic acid)‐graft‐methoxy poly(ethylene oxide) comblike copolymer

A methoxy poly(ethylene oxide) (MPEO) grafted poly(acrylic acid) (PAA) comblike copolymer was synthesized by the direct condensation of MPEO onto the PAA backbone in the presence of dicyclohexyl dimethylcarbodiimide (DCC) and 4‐dimethylaminopyridine (DMAP). Its chemical structure was characterized by Fourier transform infrared and ¹H‐NMR spectroscopies. The effects of different catalysts, solvents, reaction temperatures, and reaction times on the grafting degree of the PAA‐g‐MPEO comblike copolymer were investigated. Compared to p‐toluene sulfonic acid, DMAP/DCC as a catalyst markedly increased the grafting degree. The optimum reaction conditions were a tetrahydrofuran/water mixture solvent, a reaction temperature of 50°C, and a reaction time of 168 h. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Grafting of poly(3‐hydroxyalkanoate) and linoleic acid onto chitosan

Poly(3‐hydroxy octanoate) (PHO), poly(3‐hydroxy butyrate‐co‐3‐hydroxyvalerate) (PHBV), and linoleic acid were grafted onto chitosan via condensation reactions between carboxylic acids and amine groups. Unreacted PHAs and linoleic acid were eliminated via chloroform extraction and for elimination of unreacted chitosan were used 2 wt % of HOAc solution. The pure chitosan graft copolymers were isolated and then characterized by FTIR, ¹³C‐NMR (in solid state), DSC, and TGA. Microbial polyester percentage grafted onto chitosan backbone was varying from 7 to 52 wt % as a function of molecular weight of PHAs, namely as a function of steric effect. Solubility tests were also performed. Graft copolymers were soluble, partially soluble or insoluble in 2 wt % of HOAc depending on the amount of free primary amine groups on chitosan backbone or degree of grafting percent. Thermal analysis of PHO‐g‐Chitosan graft copolymers indicated that the plastizer effect of PHO by means that they showed melting transitions T_ms at 80, 100, and 113°C or a broad T_ms between 60.5–124.5°C and 75–125°C while pure chitosan showed a sharp T_m at 123°C. In comparison of the solubility and thermal properties of graft copolymers, linoleic acid derivatives of chitosan were used. Thus, the grafting of poly(3‐hydroxyalkanoate) and linoleic acid onto chitosan decrease the thermal stability of chitosan backbone. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103:81–89, 2007     

Swelling behavior and cell viability of dehydrothermally crosslinked poly(vinyl alcohol) hydrogel grafted with N‐vinyl pyrrolidone or acrylic acid using γ‐radiation

To improve equilibrium water content, dehydrothermally crosslinked poly(vinyl alcohol) (PVA) hydrogel was grafted with N‐vinyl pyrrolidone (NVP) or acrylic acid (AA) monomer using γ‐radiation. Swelling behavior of the grafted hydrogels was studied in phosphate‐buffered saline, and cell viability was evaluated using fibroblast cells from mouse connective tissue. Equilibrium water content of AA‐ and NVP‐grafted PVA hydrogel ranged between 40–60% and 60–80%, respectively, depending on radiation dose and monomer concentration. For maximum degree of swelling, the optimum monomer concentration and radiation dose were 20% by weight and 20 kGy, respectively. Fibroblast cells seeded on NVP‐grafted hydrogel had an extended oval morphology while those seeded on AA‐grafted PVA had a rounded spherical morphology. These results support the use of NVP for grafting PVA to increase swelling and improve cell viability. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2862–2868, 2004     

Zwitterionic sulfobetaine‐modified non‐woven fabric for blood filtration

Blood filtration requires a high removal ratio of leukocytes and with simultaneous high recovery ratio of platelets and other beneficial components. Problems are often encountered with blood filter materials in terms of high platelet loss. Zwitterions such as phosphorylcholine, sulfobetaine and carboxybetaine show effective resistance against protein adsorption and platelet adhesion. The study reported was aimed at achieving surface modification of poly(butylene terephthalate) non‐woven fabric (PBTNF) using UV radiation‐induced graft copolymerization of a zwitterionic sulfobetaine, N‐(3‐sulfopropyl)‐N‐methacroyloxyethyl‐N,N‐dimethylammonium betaine (SMDB), in order to improve the wettability and platelet recovery ratio of the PBTNF. Attenuated total reflection Fourier transform infrared and X‐ray photoelectron spectroscopy results showed that SMDB was successfully grafted onto the PBTNF. Photoinitiator concentration, monomer concentration and UV irradiation time affected markedly the degree of grafting. Critical wetting surface tension, water wetting time and hemolysis tests showed an improvement in wettability and blood compatibility as a result of graft copolymerization of SMDB. A blood filter material composed of SMDB‐modified PBTNF reduced platelet adhesion and had higher platelet recovery compared to poly(acrylic acid)‐modified PBTNF. It was found that SMDB monomer was successfully grafted onto PBTNF using UV radiation. The degree of grafting of SMDB could be controlled by varying the photoinitiator concentration, monomer concentration and UV irradiation time. SMDB‐modified PBTNF showed significant improvement in wettability and blood compatibility. The zwitterionic structure of SMDB is resistant to platelet adhesion. The SMDB‐modified PBTNF could be a candidate for a blood filter material and in other medical applications. Copyright © 2010 Society of Chemical Industry     

Lipases improve the grafting of poly(ethylene terephthalate) fabrics with acrylic acid

In this study, poly(ethylene terephthalate) (PET) fabrics were modified with two types of commercial lipases, namely, Lipex and Lipolase, and grafted with acrylic acid (AA) to improve their absorption properties. The effects of the enzyme concentration, reaction temperature, time, and pH on the grafting of AA onto PET were investigated. The pretreatment of PET with lipases increased the amount of AA that was introduced to the PET fibers, whereas AA grafting onto the untreated PET fabrics led to lower graft yields. Fourier transform infrared spectroscopy and scanning electron microscopy were used to characterize the AA‐grafted pretreated polyester fabrics. A new band appearing at 1546 cm^?1 in the Fourier transform infrared spectrum implied that AA was introduced onto the PET fabrics. The surfaces of the fabric fibers presented in scanning electron microscopy micrographs clearly indicated the formation of a layer of grafted poly (acrylic acid). The results show that the density of surface grafting was improved by the lipase pretreatment. The increase in grafting was higher for Lipex than for Lipolase. The highest graft yield was obtained with 1% Lipex and Lipolase for 30 min at pH values of 7 and 5, respectively. There were no significant changes in the tenacity or weight reduction of the fabrics. The moisture content of the samples increased linearly with increasing graft yield. This was higher for the pretreated fabrics grafted with Lipex. A higher color strength was obtained for grafted PET samples that were pretreated with Lipex when they were dyed in alkaline aqueous solutions. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The effect of interface modification between POM and PTFE on the properties of POM/PTFE composites

A plasma technique was applied to modify the surface of polytetrafluoroethylene (PTFE) fiber to improve the compatibility between PTFE and polyacetal (POM). This technique used argon (Ar) plasma to treat PTFE fiber first and then grafting the fiber with acrylic acid (AAc) by peroxidation. The Ar plasma‐treated PTFE (PPTFE) fiber and AAc‐grafted PPTFE (AAc‐g‐PPTFE) fiber were added into POM to increase the wear resistance and to decrease the friction coefficient of POM. The variables of the experiments were plasma treatment time, monomer concentration of AAc, and grafting time. The graft copolymer was characterized by Fourier transform infrared (FTIR) spectroscopy. The stress–strain behavior, impact strength, Taber wear factor, friction coefficient, and morphology of composites were also investigated. The properties of POM/PTFE composites could be successful modified by surface modification of PTFE in this investigation. The impact strength of POM/AAc‐g‐PPTFE composites was more than twice of that of POM/PTFE composites. The Taber wear factor and friction coefficient of POM/AAc‐g‐PPTFE composites decreased markedly. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 800–807, 2000