An ultrathin vertical channel MOSFET for sub-100-nm applications

An ultrathin vertical channel (UTVC) MOSFET with an asymmetric gate-overlapped low-doped drain (LDD) is experimentally demonstrated. In the structure, the UTVC (15 nm) was obtained using the cost-effective solid phase epitaxy, and the boron-doped poly-Si/sub 0.5/Ge/sub 0.5/ gate was adopted to adjust the threshold voltage. The fabricated NMOSFET offers high-current drive due to the lightly doped (<1/spl times/10/sup 15/ cm/sup -3/) channel, which suppresses the electron mobility degradation. Moreover, an asymmetric gate-overlapped LDD was used to suppress the offstate leakage current and reduce the source/drain series resistance significantly as compared to the conventional symmetrical LDD. The on-current drive, offstate leakage current, subthreshold slope, and DIBL for the fabricated 50-nm devices are 325 /spl mu/A//spl mu/m, 8/spl times/10/sup -9/ /spl mu/A//spl mu/m, 87 mV/V, and 95 mV/dec, respectively.     

SODEL FET: novel channel and source/drain profile engineering schemes by selective Si epitaxial growth technology

In this paper, novel channel and source/drain profile engineering schemes are proposed for sub-50-nm bulk CMOS applications. This device, referred to as the silicon-on-depletion layer FET (SODEL FET), has the depletion layer beneath the channel region, which works as an insulator like a buried oxide in a silicon-on-insulator MOSFET. Thanks to this channel structure, junction capacitance (C/sub j/) has been reduced in SODEL FET, i.e., C/sub j/ (area) was /spl sim/0.73 fF//spl mu/m/sup 2/ both in SODEL nFET and pFET at Vbias =0.0 V. The body effect coefficient /spl gamma/ is also reduced to less than 0.02 V/sup 1/2/. Nevertheless, current drives of 886 /spl mu/A//spl mu/m (I/sub off/=15 nA//spl mu/m) in nFET and -320 /spl mu/A//spl mu/m (I/sub off/=10 nA//spl mu/m) in pFET have been achieved in 70-nm gate length SODEL CMOS with |V/sub dd/|=1.2 V. New circuit design schemes are also proposed for high-performance and low-power CMOS applications using the combination of SODEL FETs and bulk FETs on the same chip for 90-nm-node generation and beyond.     

Ideal rectangular cross-section Si-Fin channel double-gate MOSFETs fabricated using orientation-dependent wet etching

Ultranarrow and ideal rectangular cross section silicon(Si)-Fin channel double-gate MOSFETs (FXMOSFETs) have successfully been fabricated for the first time using [110]-oriented silicon-on-insulator (SOI) wafers and orientation-dependent wet etching. The transconductance (g/sub m/) normalized by 2/spl times/(Fin height) is found to be as high as 700 /spl mu/S//spl mu/m at V/sub d/=1 V in the fabricated 13-nm-thick and 82-nm-high Si- Fin channel double-gate MOSFET with a 105-nm gate length and a 2.2-nm gate oxide. The almost-ideal S-slope of 64 mV/decade is demonstrated in a 145-nm gate length device. These excellent results show that the Si-Fin channel with smooth [111]-oriented sidewalls is suitable to realize a high-performance FXMOSFET. The short-channel effects (SCEs) are effectively suppressed by reducing the Si-Fin thickness to 23 nm or less.     

InGaAs/InP DHBTs with 120-nm collector having simultaneously high f/sub /spl tau//, f/sub max//spl ges/450 GHz

InP/In/sub 0.53/Ga/sub 0.47/As/InP double heterojunction bipolar transistors (DHBT) have been designed for increased bandwidth digital and analog circuits, and fabricated using a conventional mesa structure. These devices exhibit a maximum 450 GHz f/sub /spl tau// and 490 GHz f/sub max/, which is the highest simultaneous f/sub /spl tau// and f/sub max/ for any HBT. The devices have been scaled vertically for reduced electron collector transit time and aggressively scaled laterally to minimize the base-collector capacitance associated with thinner collectors. The dc current gain /spl beta/ is /spl ap/ 40 and V/sub BR,CEO/=3.9 V. The devices operate up to 25 mW//spl mu/m/sup 2/ dissipation (failing at J/sub e/=10 mA//spl mu/m/sup 2/, V/sub ce/=2.5 V, /spl Delta/T/sub failure/=301 K) and there is no evidence of current blocking up to J/sub e//spl ges/12 mA//spl mu/m/sup 2/ at V/sub ce/=2.0 V from the base-collector grade. The devices reported here employ a 30-nm highly doped InGaAs base, and a 120-nm collector containing an InGaAs/InAlAs superlattice grade at the base-collector junction.     

1.5-V single work-function W/WN/n/sup +/-poly gate CMOS device design with 110-nm buried-channel PMOS for 90-nm vertical-cell DRAM

This letter reports on 1.5-V single work-function W/WN/n/sup +/-poly gate CMOS transistors for high-performance stand-alone dynamic random access memory (DRAM) and low-cost low-leakage embedded DRAM applications. At V/sub dd/ Of 1.5-V and 25/spl deg/C, drive currents of 634 /spl mu/A//spl mu/m for 90-nm L/sub gate/ NMOS and 208 /spl mu/A-/spl mu/m for 110-nm L/sub gate/ buried-channel PMOS are achieved at 25 pA//spl mu/m off-state leakage. Device performance of this single work function technology is comparable to published low leakage 1.5-V dual work-function technologies and 25% better than previously reported 1.8-V single work-function technology. Data illustrating hot-carrier immunity of these devices under high electric fields is also presented. Scalability of single work-function CMOS device design for the 90-nm DRAM generation is demonstrated.     

50-nm gate Schottky source/drain p-MOSFETs with a SiGe channel

We propose new SiGe channel p-MOSFETs with germano-silicide Schottky source/drains (S/Ds). The Schottky barrier-height (SBH) for SiGe is expected to be low enough to improve the injection of carriers into the SiGe channel and, as a result, current drivability is also expected to improve. In this work, we demonstrate the proposed Schottky S/D p-MOSFETs down to a 50-nm gate-length. The drain current and transconductance are -339 /spl mu/A//spl mu/m and 285 /spl mu/S//spl mu/m at V/sub GS/=V/sub DS/=-1.5 V, respectively. By increasing the Ge content in the SiGe channel from 30% to 35%, the drive current. and transconductance can be improved up to 23% and 18%, respectively. This is partly due to the lower barrier-height for strained Si/sub 0.65/Ge/sub 0.35/ channel than those for strained Si/sub 0.7/Ge/sub 0.3/ channel device and partly due to the lower effective mass of the holes.     

Graded base type-II InP/GaAsSb DHBT with f/sub T/=475 GHz

The first demonstration of a type-II InP/GaAsSb double heterojunction bipolar transistor (DHBT) with a compositionally graded InGaAsSb to GaAsSb base layer is presented. A device with a 0.4/spl times/6 /spl mu/m/sup 2/ emitter dimensions achieves peak f/sub T/ of 475 GHz (f/sub MAX/=265 GHz) with current density at peak f/sub T/ exceeding 12 mA//spl mu/m/sup 2/. The structure consists of a 25-nm InGaAsSb/GaAsSb graded base layer and 65-nm InP collector grown by MBE with breakdown voltage /spl sim/4 V which demonstrates the vertical scaling versus breakdown advantage over type-I DHBTs.     

high-performance and high-reliability 80-nm gate-length DTMOS with indium super steep retrograde channel

In this paper, we demonstrate for the first time a high-performance and high-reliability 80-nm gate-length dynamic threshold voltage MOSFET (DTMOS) using indium super steep retrograde channel implantation. Due to the steep indium super steep retrograde (In SSR) dopant profile in the channel depletion region, the novel In-SSR DTMOS features a low V/sub th/ in the off-state suitable for low-voltage operation and a large body effect to fully exploit the DTMOS advantage simultaneously, which is not possible with conventional DTMOS. As a result, excellent 80-nm gate length transistor characteristics with drive current as high as 348 /spl mu/A//spl mu/m (off-state current 40 nA//spl mu/m), a record-high Gm=1022 mS/mm, and a subthreshold slope of 74 mV/dec, are achieved at 0.7 V operation. Moreover, the reduced body effects that have seriously undermined conventional DTMOS operation in narrow-width devices are alleviated in the In-SSR DTMOS, due to reduced indium dopant segregation. Finally, it was found for the first time that hot-carrier reliability is also improved in DTMOS-mode operation, especially for In-SSR DTMOS.     

Characterization of 1.9- and 1.4-nm ultrathin gate oxynitride by oxidation of nitrogen-implanted silicon substrate

For gate oxide thinned down to 1.9 and 1.4 nm, conventional methods of incorporating nitrogen (N) in the gate oxide might become insufficient in stopping boron penetration and obtaining lower tunneling leakage. In this paper, oxynitride gate dielectric grown by oxidation of N-implanted silicon substrate has been studied. The characteristics of ultrathin gate oxynitride with equivalent oxide thickness (EOT) of 1.9 and 1.4 nm grown by this method were analyzed with MOS capacitors under the accumulation conditions and compared with pure gate oxide and gate oxide nitrided by N/sub 2/O annealing. EOT of 1.9- and 1.4-nm oxynitride gate dielectrics grown by this method have strong boron penetration resistance, and reduce gate tunneling leakage current remarkably. High-performance 36-nm gate length CMOS devices and CMOS 32 frequency dividers embedded with 57-stage/201-stage CMOS ring oscillator, respectively, have been fabricated successfully, where the EOT of gate oxynitride grown by this method is 1.4 nm. At power supply voltage V/sub DD/ of 1.5 V drive current Ion of 802 /spl mu/A//spl mu/m for NMOS and -487 /spl mu/A//spl mu/m for PMOS are achieved at off-state leakage I/sub off/ of 3.5 nA//spl mu/m for NMOS and -3.0 nA//spl mu/m for PMOS.     

Enhancing leakage suppression in carbon-rich silicon junctions

Carbon-incorporated devices exhibit an increase in junction leakage relative to pure Si devices. The authors demonstrate that a leakage suppression of /spl sim/ 50 times can be achieved in carbon-rich (Si:C) junctions. This is accomplished by a prolonged annealing for 1 to 10 min at 850 /spl deg/C (much lower than typical annealing temperature of >1000/spl deg/C) and is attributed to a decrease in interstitial carbon concentration. After a 10-min annealing, the Si:C junctions display a leakage of 4/spl times/10/sup -13/ A//spl mu/m, which is much lower than that of 1050 /spl deg/C spike annealed Si junctions and well within the I/sub off/ requirements of low-standby-power device at the 45-nm node. Carbon-incorporated transistors with a gate length of 0.18 /spl mu/m exhibit an I/sub off/ reduction of /spl sim/ 10 times, compared to pure Si transistors, and both transistors have a similar subthreshold slope of 81 mV/dec.     

Implementation and characterization of the double-gate MOSFET using lateral solid-phase epitaxy

In this paper, a simple high performance double-gate metal oxide semiconductor field effect transistor (MOSFET) using lateral solid-phase epitaxy (LSPE) is experimentally demonstrated and characterized. The thin channel of the double-gate MOSFET was obtained using the high quality LSPE crystallized layer. The fabricated double-gate MOSFET provides good current drive capability and steep subthreshold slope, and they are approximately 350 /spl mu/A//spl mu/m (@ V/sub ds/ = 2.5 V and V/sub gs/ - V/sub T/ = 2.5 V) and 78 mV/dec for the devices with 0.5 /spl mu/m channel length. Compared to the conventional single-gate transistor, the double-gate NMOSFET fabricated on the LSPE layer has better V/sub T/ roll-off characteristics, DIBL effect, and 1.72 times higher current drive. The peak effective electron mobility of the LSPE crystallized layer is approximately 382 cm/sup -2//V.s.     

High-frequency performance of subthreshold SOI MESFETs

Results from silicon-on-insulator (SOI) MESFETs designed for subthreshold operation are presented. The transistors have subthreshold slopes as low as 78 mV/dec and off-state drain currents approaching 1 pA//spl mu/m. Drain current saturation can be achieved with drain voltages of less than 0.5 V and with output impedance>100 M/spl Omega//spl middot//spl mu/m. The cutoff frequency of a 500-nm gate length device exceeds 1 GHz at currents significantly less than 1 /spl mu/A//spl mu/m. These results suggest that subthreshold SOI MESFETs might have useful applications in mixed-signal, micropower circuit design.     

A 22-nm damascene-gate MOSFET fabrication with 0.9-nm EOT and local channel implantation

We introduce a novel CMOS transistor fabrication technique using damascene gate with local channel implantation (LCI). This transistor has a benefit to reduce the resistance of source/drain extension (SDE) localizing the severe blanket channel implantation under the channel only. It can reduce the junction capacitance as well. This process technology is reliable for the formation of channel length down to 22 nm with smooth gate line edge roughness. Some unique processes for the small transistor fabrication are also introduced. The 22-nm nMOSFET with 0.9 nm RTO is achieved with the drive current of 930 /spl mu/A//spl mu/m for the off-current of 100 nA//spl mu/m at 1.0 V. Hot carrier reliability exceeding 10 years for 1.0 V operation is also obtained.     

Electrical characteristics and lifetimes of microdischarge devices having thin dielectric films of aluminum oxide,boron nitride, or barium titanate

The electrical (V-I) characteristics, radiative efficiencies, and lifetimes of Ni screen/dielectric/Ni microdischarge devices, having overall thicknesses as small as <100 /spl mu/m and cylindrical microchannels 50-150 /spl mu/m in diameter, are investigated for Al/sub 2/O/sub 3/, BN, and BaTiO/sub 3/ dielectric films that are 120 or 200 /spl mu/m, 30 /spl mu/m, and 5 /spl mu/m in thickness, respectively. Having dielectrics fabricated by sol-gel processes or colloidal deposition and operated with Ne gas pressures between 300 and 1200 Torr (300K), these devices operate at voltages as low as /spl sim/93 V (100 /spl mu/m dia. BaTiO/sub 3/ device), and exhibit exceptional stability and lifetimes. After 100 h of continuous operation, a Ni screen/30 /spl mu/m BN/Ni device operating in 700 Torr Ne (static gas fill) at 100 V produces /spl sim/98% of its initial radiant output.     

A functional 41-stage ring oscillator using scaled FinFET devices with 25-nm gate lengths and 10-nm fin widths applicable for the 45-nm CMOS node

In this letter, we have fabricated a functional FinFET ring oscillator with a physical gate length of 25 nm and a fin width of 10 nm, the smallest ever reported. We demonstrate that these narrow (W/sub fin/ = 10 nm) and tall (H/sub fin/ = 60 - 80 nm) fins can be reliably etched with controlled profiles and that they are required to keep the short-channel effects under control, resulting in drain-induced barrier leakage characteristics of 45 mV/V at V/sub dd/ = 1 V and L/sub g/ = 25 nm for the nFET. For these ultrathin (10 nm) fins, we have succeeded in properly setting the V/sub T/ at 0.2 V without the use of metal gates. In addition to ring oscillators, we also have obtained excellent pFET FinFET devices at wider fin widths (W/sub fin/ = 65 nm) with I/sub dsat/ = 380 /spl mu/A//spl mu/m at I/sub off/ = 60 nA//spl mu/m and V/sub dd/ = -1.2 V.     

15-nm base type-II InP/GaAsSb/InP DHBTs with F/sub T/=384 GHz and a 6-V BV/sub CEO/

Type-II InP/GaAsSb/InP double heterojunction bipolar transistors (DHBTs) with a 15-nm base were fabricated by contact lithography: 0.73/spl times/11 /spl mu/m/sup 2/ emitter devices feature f/sub T/=384GHz (f/sub MAX/=262GHz) and BV/sub CEO/=6V. This is the highest f/sub T/ ever reported for InP/GaAsSb DHBTs, and an "all-technology" record f/sub T//spl times/BV/sub CEO/ product of 2304 GHz/spl middot/V. This result is credited to the favorable scaling of InP/GaAsSb/InP DHBT breakdown voltages (BV/sub CEO/) in thin collector structures.     

High-temperature thermal stability performance in /spl delta/-doped In/sub 0.425/Al/sub 0.575/As--In/sub 0.65/Ga/sub 0.35/As metamorphic HEMT

We report, to our knowledge, the best high-temperature characteristics and thermal stability of a novel /spl delta/-doped In/sub 0.425/Al/sub 0.575/As--In/sub 0.65/Ga/sub 0.35/As--GaAs metamorphic high-electron mobility transistor. High-temperature device characteristics, including extrinsic transconductance (g/sub m/), drain saturation current density (I/sub DSS/), on/off-state breakdown voltages (BV/sub on//BV/sub GD/), turn-on voltage (V/sub on/), and the gate-voltage swing have been extensively investigated for the gate dimensions of 0.65/spl times/200 /spl mu/m/sup 2/. The cutoff frequency (f/sub T/) and maximum oscillation frequency (f/sub max/), at 300 K, are 55.4 and 77.5 GHz at V/sub DS/=2 V, respectively. Moreover, the distinguished positive thermal threshold coefficient (/spl part/V/sub th///spl part/T) is superiorly as low as to 0.45 mV/K.     

A 2-V 23-/spl mu/A 5.3-ppm//spl deg/C curvature-compensated CMOS bandgap voltage reference

A high-order curvature-compensated CMOS bandgap reference, which utilizes a temperature-dependent resistor ratio generated by a high-resistive poly resistor and a diffusion resistor, is presented in this paper. Implemented in a standard 0.6-/spl mu/m CMOS technology with V/sub thn//spl ap/|V/sub thp/|/spl ap/0.9 V at 0/spl deg/C, the proposed voltage reference can operate down to a 2-V supply and consumes a maximum supply current of 23 /spl mu/A. A temperature coefficient of 5.3 ppm//spl deg/C at a 2-V supply and a line regulation of /spl plusmn/1.43 mV/V at 27/spl deg/C are achieved. Experimental results show that the temperature drift is reduced by approximately five times when compared with a conventional bandgap reference in the same technology.     

Improvement of short-channel characteristics of a 0.1-/spl mu/m PMOSFET with ultralow-temperature nitride spacer by using a novel oxide capped boron uphill treatment

In this work, the thermal annealing at 720/spl deg/C for 2 hr (called boron uphill treatment) with an SiO/sub 2/-capped layer was applied after source/drain extensions (SDE) implantation to improve the short channel characteristics of a 0.1-/spl mu/m PMOSFET with an ultra-low temperature nitride spacer. The influence and the mechanism of the capped layer on this uphill treatment were investigated. The results show that the capped layer treatment indeed leads to a shallower junction, improved V/sub th/ roll-off characteristic, and added immunity against subsurface punchthrough.     

10-Gb/s limiting amplifier and laser/modulator driver in 0.18-/spl mu/m CMOS technology

A limiting amplifier incorporates active feedback, inductive peaking, and negative Miller capacitance to achieve a voltage gain of 50 dB, a bandwidth of 9.4 GHz, and a sensitivity of 4.6 mV/sub pp/ for a bit-error rate of 10/sup -12/ while consuming 150 mW. A driver employs T-coil peaking and negative impedance conversion to achieve operation at 10 Gb/s while delivering a current of 100 mA to 25-/spl Omega/ lasers or a voltage swing of 2 V/sub pp/ to 50-/spl Omega/ modulators with a power dissipation of 675 mW. Fabricated in 0.18-/spl mu/m CMOS technology, both prototypes operate with a 1.8-V supply.