多壁碳纳米管增强炭黑/聚丙烯导电复合材料导电行为

为了充分利用不同导电粒子的导电作用,在炭黑(CB)/聚丙烯(PP)导电复合体系中引入了多壁碳纳米管(CNTs)。研究发现：引入的CNTs分散在CB粒子间起到“桥梁”作用,使体系的导电性能得到明显改善,并且CB∶CNTs为19∶1时其协同导电效果最好,该复合体系出现逾渗现象,对应的导电填料体积分数明显降低。在导电填料总体积分数为4.76%时,少量CNTs的引入就可使复合体系的体积电阻率从109Ω·cm下降到105Ω·cm;同时少量的CNTs能明显抑制炭黑/聚丙烯导电复合材料的正温度效应(PTC),使PTC强度从6.10降低到1.48,PTC转变峰温度从166℃升高到174℃。少量的 CNTs可以使PP的结晶温度提高12℃,对PP结晶的成核作用比CB更加明显。复合体系力学性能随导电填料体积分数增加而明显降低,但因为体积电阻率一定时CB-CNTs/PP体系所需导电填料体积分数较CB/PP体系明显降低,因此少量CNTs的引入能够使复合体系的力学性能得到更大程度的保持。     

HDPE/EVA/CB复合导电材料的研究

研究了HDPE/EVA/CB(炭黑)复合材料的导电性及正温度系数(PTC)特性,包括电阻-温度特性和电流-时间特性.发现在HDPE/CB复合材料中加入少量的EVA能降低室温电阻率、改善炭黑粒子的分散、增强PTC效应以及缩短材料的响应时间,并从基体的结晶性及炭黑在共混基体中分布的角度探讨了EVA组分对复合材料电性能影响的作用机理.     

炭黑结构度对HDPE/CB导电复合材料导电网络形成与破坏的影响

采用熔融混合方法制备高密度聚乙烯/炭黑(HDPE/CB)导电复合材料,比较不同结构度CB填充体系的逾渗曲线和温度-电阻行为,并研究了不同含量、不同结构度CB填充的HDPE的结晶行为。实验结果表明,高结构度CB可使填充体系逾渗值显著下降(本研究中可降低为2.7%);低结构度CB填充体系的正温度系数(PTC)效应强度比高结构度CB填充体系高出约3;降温过程中,温度-电阻率曲线上出现电阻突变峰的强度随着CB结构度的降低而增强;差示扫描量热(DSC)和广角X射线衍射(WAXD)结果显示,CB粒子的加入对HDPE的结晶行为没有显著影响。     

炭黑改性对炭黑/高密度聚乙烯体系电性能稳定性的影响

采用熔体共混法制备了炭黑（CB）/高密度聚乙烯（HDPE）导电复合材料。研究了硝酸氧化对CB/HDPE导电复合材料正温度系数（PTC）、负温度系数（NTC）效应和电性能稳定性的影响。结果表明,填充氧化炭黑（CB-O）提高了CB-O/HDPE体系的电性能稳定性和PTC强度,部分消除或降低了复合材料的NTC效应。而CB-O/HDPE体系的室温电阻率比CB/HDPE体系只增加了0.3个数量级,但比经过交联处理的CB/HDPE（CB/crosslinked-HDPE）体系降低了1个数量级。CB-O/HDPE复合材料性能的改善主要是由于CB经氧化后,表面羧基、羟基等极性基团含量增加,抑制了CB粒子高温时的自团聚作用,减弱了体系的NTC效应;同时CB表面微晶晶界处导电性较差区域的减少,提高了CB的导电性,,并且CB-O表面大量孔洞和裂缝的形成,增强了CB-O与HDPE的物理吸附作用,提高了复合材料的电性能稳定性。      

一种有机结晶物对丁腈橡胶/炭黑复合材料电性能的影响

将一种低分子量有机结晶物加入到丁腈橡胶/炭黑复合体系中制备导电复合材料。实验得出, 其电阻率随温度的变化呈不同强度的正温度系数(PTC) 效应。讨论了低分子量有机结晶物对复合材料室温电阻率及PTC 效应的影响。      

导电聚苯胺纳米纤维对聚乙烯/炭黑复合体系电阻行为的影响

采用水溶液氧化聚合和热掺杂相结合的技术制备十二烷基苯磺酸掺杂的聚苯胺(PANI-DBSA)纳米纤维,并将PANI-DBSA纳米纤维与低密度聚乙烯(LDPE)和炭黑(CB)进行熔融共混制得PANI-DBSA/LDPE/CB导电复合材料,研究了PANI-DBSA纤维的引入对导电复合材料电阻行为的影响。结果表明,添加PANI-DBSA纳米纤维,复合材料的逾渗阀值移向较低炭黑含量,复合材料的PTC强度得到一定程度的提高,复合材料的电阻率-温度曲线的热循环稳定性得以改善。     

高电导率炭系复合高分子材料的研制

炭黑(CB)、石墨(C)、炭纤维(CF)炭系与基体树脂以特殊的工艺复合改性制得体积电阻率小于0.1Ω.cm的高导电高分子复合材料。研究了不同的复合体系(CB/PP)/SEBS、(PP/SEBS)/CB、(CB/SEBS)/PP及不同的配方与工艺获得的复合材料对导电性能的影响,结果表明,(PP/SEBS)/CB复合体系是最佳加工方式。采用扫描电镜(SEM)、力学性能测试等方法研究了炭系导电材料在PP/SEBS树脂中的分散机理及复合材料的力学性能。实验结果表明炭系复合组分含量为60%的PP/SEBS导电复合材料具有超高电导率、优良的力学性能和加工性能。     

固化剂对炭黑/环氧树脂导电复合材料阻温特性的影响

分别以2-乙基-4-甲基咪唑(2,4-EMI)和甲基四氢邻苯二甲酸酐(MeTHPA)为固化剂,低结构炭黑(F101CB)为导电填料,环氧树脂(E-54)为基体,采用超声分散溶液混合法制备了F101/E-54/2,4-EMI和F101/E-54/MeTHPA复合材料。通过电阻-温度特性测试和差示扫描量热(DSC)法分别对其电性能和玻璃化温度进行了表征与分析。结果表明,以2,4-EMI和MeTHPA为固化剂的F101/E-54复合材料都具有PTC效应,F101/E-54/2,4-EMI复合材料具有较大的室温电阻率和PTC转变温度,较小的PTC强度;101/E-54/2,4-EMI复合材料的玻璃化温度Tg为161.7℃,与其PTC转变温度160.4℃接近,F101/E-54/MeTHPA复合材料的玻璃化温度Tg为133.5℃,与其PTC转变温度134.1℃接近;多次热循环使F101/E-54复合材料的PTC稳定性得到改善,以2,4-EMI为固化剂的复合材料体系表现得尤为明显。     

PET/MWNT/CB纳米复合材料制备与性能研究

采用原位聚合方法制备了聚对苯二甲酸乙二醇酯/多壁碳纳米管/炭黑(PET/MWNT/CB)纳米复合材料,研究了MWNT与CB对复合材料导电性能、结晶性能和热稳定性的影响,考察了二者的协同导电效应。结果表明,当MWNT与CB复合填料含量为0.5%(质量分数)时,复合材料的表面电阻为10~(11)Ω。CB与MWNT在PET中能形成"共支撑"网络结构和复合导电通路,具有协同导电效应。二者对PET具有诱导成核与结晶作用,但CB的诱导能力要弱于MWNT。CB的添加对复合材料的热稳定性影响不大。     

炭黑／聚丙烯／聚碳酸酯复合材料导电性能和PTC特性

以聚丙烯（PP）／聚碳酸酯（PC）共混物为基体,采用不同种类炭黑（CB）填充制备导电复合材料并对其导电性能和PTC特性进行研究。结果表明：在常温时,PP／PC共混基体中PP含量大于40wt％时,材料的电阻率急剧下降;共混比为50：50（wt％）复合材料的电阻率达到最小值。加热时,两者均未出现明显NTC现象,说明PP／PC的共混可以有效的消除NTC效应。但PTC强度仅为1个数量级,远低于PP／CB二元复合材料。CB是影响PTC效应的重要因素之一,达到逾渗值时随着体系CB含量减少PTC效应会增强;乙炔炭黑与炉法CB填充的CB／PP／PC复合材料相比较,前者的体积电阻率较低,而两者的逾渗阈值相近,均为6．6％;乙炔CB为填料的CB／PP／PC三元复合材料的阿C突变温度在140℃附近,以炉法CB为填料时,PTC效应突变点出现在150℃（PC的Tg）附近。DSC分析结果表明,复合材料中PP的结晶度随着CB含量增加呈上升趋势,CB含量为15％时,PP的结晶度为32．75％,对于整个PP／PC／CB体系而言结晶部分的含量较低,因此该体系的PTC效应强度较低。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Effect of Oxide Assisted Metal Nanoparticles on Microstructure and Morphology of Gallium oxide Nanowires

Several researches have been reported about the characteristic of β-Ga2O3 nanowires which was synthesized on nickel oxide particle. But indeed, recent researches about synthesis of β-Ga2O3 nanowires on oxide-assisted transition metal are limited to nickel or cobalt oxide catalyst. In this work, Gallium oxide (β-Ga2O3 ) nanowires were synthesized by a simple thermal evaporation method from gallium powder in the range of 700 - 1000℃ using the iron, nickel, copper, cobalt and zinc oxide as a catalyst, respectively. The β-Ga2O3 nanowires with single crystalline without defects were successfully synthesized at the reaction temperature of 850, 900 and 950℃ in all the catalysts. But optimum experimental condition in synthesis of nanowires varied with the kind of catalyst. As increasing synthesis temperature,the morphology of gallium oxide nanowires changed from nanowires to nanorods, and its diameter increased. From these results, we could be proposed that the growth mechanism of β-Ga2O3 nanowires was changed with synthesis temperature of nanowires. Microstructure and morphology of Synthesized nanowire was characterized by HR-TEM, FE-SEM, EDX and XRD.     

The Influence of Nitrogen and Boron Implant into Silicon Substrate on the Phase and Internal Stress of c-BN Films

Cubic boron nitride(c-BN) film was deposited on a Si (100) substrate by the RF-magnetron sputtering.The mainly problems for fabrication of c-BN films are the low purity and high intrinsic compressive stress. In order to solve the two problems, the c-BN film with the buffer interlayer was deposited on the substrate which had been implanted with nitrogen and/or boron ions. The results show: the implantation of nitrogen ions can obviously increase c-BN content and reduce the internal stress slightly; while the implantation of boron shows no obvious improvement to the content of c-BN, which can reduce the internal stress in the film obviously. In addition, it is suggested that the implantation of nitrogen and boron shows the best result, which not only can increase the content of c-BN, but also reduce the internal stress in the c-BN film obviously.