Biological hydrogen production of the genus Clostridium: Metabolic study and mathematical model simulation

The biochemical hydrogen potential (BHP) tests were conducted to investigate the metabolism of glucose fermentation and hydrogen production performance of four Clostridial species, including C. acetobutylicum M121, C. butyricum ATCC19398, C. tyrobutyricum FYa102, and C. beijerinckii L9. Batch experiments showed that all the tested strains fermented glucose, reduced medium pH from 7.2 to a value between 4.6 and 5.0, and produced butyrate (0.37–0.67 mmol/mmol-glucose) and acetate (0.34–0.42 mmol/mmol-glucose) as primary soluble metabolites. Meanwhile, a significant amount of hydrogen gas was produced accompanied with glucose degradation and acid production. Among the strains examined, C. beijerinckii L9 had the highest hydrogen production yield of 2.81 mmol/mmol-glucose. A kinetic model was developed to evaluate the metabolism of glucose fermentation of those Clostridium species in the batch cultures. The model, in general, was able to accurately describe the profile of glucose degradation as well as production of biomass, butyrate, acetate, ethanol, and hydrogen observed in the batch tests. In the glucose re-feeding experiments, the C. tyrobutyricum FYa102 and C. beijerinckii L9 isolates fermented additional glucose during re-feeding tests, producing a substantial amount of hydrogen. In contrast, C. butyricum ATCC19398 was unable to produce more hydrogen despite additional supply of glucose, presumably due to the metabolic shift from acetate/butyrate to lactate/ethanol production.     

Characterization on hydrogen production performance of a newly isolated Clostridium beijerinckii YA001 using xylose

A mesophilic bacterium was isolated from cow manure, and identified as Clostridium beijerinckii YA001 based on 16S rRNA gene sequence calculation using MEGA 5.0 and biochemical tests. This strain showed the ability to digest a wide range of carbon and nitrogen sources for hydrogen production, and it showed high hydrogen production performance using xylose as substrate. The optimum parameters for bio-hydrogen production in batch tests were pH 8.0, 1% substrate concentration, 40 °C and yeast extract as nitrogen source. The maximum hydrogen yield and the hydrogen production rate were obtained at 2.31 mol/mol xylose and 311.3 mL H₂/(Lh), respectively. These results indicate that C. beijerinckii YA001 is an ideal candidate for fermentative hydrogen production.     

Optimization of hydrogen production by hyperthermophilic eubacteria, Thermotoga maritima and Thermotoga neapolitana in batch fermentation

The batch fermentations of two hyperthermophilic eubacteria Thermotoga maritima strain DSM 3109 and Thermotoga neapolitana strain DSM 4359 were carried out to optimize the hydrogen production. The simple and economical culture medium using cheap salts with strong buffering capacity was designed based on T. maritima basal medium (TMB). Both strains cultivated under strictly anaerobic conditions showed the best growth at temperature of 75–80 °C and pH of 6.5–7.0. The maximum cell growth of 3.14 g DCW/L and hydrogen production of 342 mL H₂ gas/L were obtained, respectively, in the modified TB medium containing 7.5 g/L of glucose and 4 g/L of yeast extract. Hydrogen accumulation in the headspace was more than 30% of the gaseous phase. Cells were also cultivated in cellulose-containing medium to test the feasibility of hydrogen production.     

High biohydrogen yielding Clostridium sp. DMHC-10 isolated from sludge of distillery waste treatment plant

A mesophilic high hydrogen producing strain DMHC-10 was isolated from a lab scale anaerobic reactor being operated on distillery wastewater for hydrogen production. DMHC-10 was identified as Clostridium sp. on the basis of 16S rRNA gene sequencing. Various medium components (carbon and nitrogen sources) and environmental factors (initial pH, temperature of incubation) were optimized for hydrogen production by Clostridium sp. DMHC-10. The strain, in late exponential growth phase, showed maximum hydrogen production (3.35 mol-H₂ mol⁻¹ glucose utilized) at 37 °C, pH 5.0 in a medium supplemented with organic nitrogen source. Butyric acid to acetic acid ratio was ca. 2.3. Hydrogen production declined when organic nitrogen was replaced with inorganic nitrogen.     

Biohydrogen production from wastewater by Clostridium beijerinckii: Effect of pH and substrate concentration

An investigation of biological hydrogen production from glucose by Clostridium beijerinckii was conducted in a synthetic wastewater solution. A study examining the effect of initial pH (range 5.7–6.5) and substrate loading (range 1–3 g COD/L) on the specific conversion and hydrogen production rate has shown interaction behaviour between the two independent variables. Highest conversion of 10.3 mL H₂/(g COD/L) was achieved at pH of 6.1 and glucose concentration of 3 g COD/L, whereas the highest production rate of 71 mL H₂/(h L) was measured at pH 6.3 and substrate loading of 2.5 g COD/L. In general, there appears to be a strong trend of increasing hydrogen production rate with an increase in both substrate concentration and pH. Butyrate (14–63%), formate (10–45%) and ethanol (16–40%) were the main soluble products with other volatile fatty acids and alcohols present in smaller quantities.     

Characteristics of fermentative hydrogen production with Klebsiella pneumoniae ECU-15 isolated from anaerobic sewage sludge

Klebsiella pneumoniae ECU-15 (EU360791), which was isolated from anaerobic sewage sludge, was investigated in this paper for its characteristics of fermentative hydrogen production. It was found that the anaerobic condition favored hydrogen production than that of the micro-aerobic condition. Culture temperature and pH of 37 °C and 6.0 were the most favorable for the hydrogen production. The strain could grow in several kinds of monosaccharide and disaccharide, as well as the complicated corn stalk hydrolysate, with the best results exhibited in glucose. The maximum hydrogen production rate and yield of 482 ml/l/h and 2.07 mol/mol glucose were obtained at initial glucose concentration of 30 g/L and 5 g/L, respectively. Fermentation results in the diluent corn stalk hydrolysate showed that cell growth was not inhibited. However, the hydrogen production of 0.65 V/V was relatively lower than that of the glucose (1.11 V/V), which was mainly due to the interaction between xylose and glucose.     

Hydrogen production using Clostridium saccharoperbutylacetonicum N1-4 (ATCC 13564)

Fermentative hydrogen production was carried out using Clostridium saccharoperbutylacetonicum N1-4 (ATCC 13564). This work investigates the effects of initial substrate concentration, initial medium pH, and temperature. The hydrogen yield was about 3.1 mol (mol glucose)⁻¹ when starting with an initial glucose concentration of 10 gl⁻¹ and initial a pH of 6.0 ± 0.2 at a temperature of 37 °C. The volume of hydrogen produced decreased when higher initial glucose concentrations were applied. The most suitable conditions for hydrogen production in a batch reactor were observed at initial pH 6.0 ± 0.2 and 37 °C.     

Biohydrogen production by Ethanoligenens harbinense B49: Nutrient optimization

A new hydrogen-producing bacterial strain Ethanoligenens harbinense B49 was examined for its capability of H₂ production with glucose as sole carbon source. The H₂ production was significantly affected by the concentration of the yeast powder and phosphate in the synthetic medium. The optimized concentration of yeast powder was 0.3–0.5 g/L and the maximum hydrogen yield was obtained at the concentration of phosphate about 100–150 mmol/L. The dynamics of hydrogen production showed that rapid evolution of hydrogen appeared to start after the middle-phase of exponential growth (about 8 h). The maximum H₂ yield and specific hydrogen production rate were estimated to be 2.26 mol H₂/mol glucose and 27.74 mmol H₂/g cell, respectively, when 10 g/L of glucose was present in the medium. The possible pathway of hydrogen production by Ethanoligenens sp. B49 during glucose fermentation was oxidative decarboxylation of pyruvate and the NADH pathway.     

Biohydrogen production by Clostridium butyricum EB6 from palm oil mill effluent

A hydrogen producer was successfully isolated from anaerobic digested palm oil mill effluent (POME) sludge. The strain, designated as Clostridium butyricum EB6, efficiently produced hydrogen concurrently with cell growth. A controlled study was done on a synthetic medium at an initial pH value of 6.0 with 10 g/L glucose with the maximum hydrogen production at 948 mL H₂/L-medium and the volumetric hydrogen production rate at 172 mL H₂/L-medium/h. The supplementation of yeast extract was shown to have a significant effect with a maximum hydrogen production of 992 mL H₂/L-medium at 4 g/L of yeast extract added. The effect of pH on hydrogen production from POME was investigated. Experimental results showed that the optimum hydrogen production ability occurred at pH 5.5. The maximum hydrogen production and maximum volumetric hydrogen production rate were at 3195 mL H₂/L-medium and 1034 mL H₂/L-medium/h, respectively. The hydrogen content in the biogas produced was in the range of 60–70%.     

Comparative study of biohydrogen production by four dark fermentative bacteria

Dark fermentation is a promising biological method for hydrogen production because of its high production rate in the absence of light source and variety of the substrates. In this study, hydrogen production potential of four dark fermentative bacteria (Clostridium butyricum, Clostridium pasteurianum, Clostridium beijerinckii, and Enterobacter aerogenes) using glucose as substrate was investigated under anaerobic conditions. Batch experiments were conducted to study the effects of initial glucose concentration on hydrogen yield, hydrogen production rate and concentration of volatile fatty acids (VFA) in the effluents. Among the four different fermentative bacteria, C. butyricum showed great performance at 10 g/L of glucose with hydrogen production rate of 18.29 mL-H₂/L-medium/hand specific hydrogen production rate of 3.90 mL-H₂/g-biomass/h. In addition, it was found that the distribution of volatile fatty acids was different among the fermentative bacteria. C. butyricum and C. pasteurianum had higher ratio of acetate to butyrate compared to the other two species, which favored hydrogen generation.     

Hydrogen production by Escherichia coli ΔhycA ΔlacI using cheese whey as substrate

This study reports a fermentative hydrogen production by Escherichia coli using cheese whey as substrate. To improve the biohydrogen production, an E. coli ΔhycA ΔlacI strain (WDHL) was constructed. The absence of hycA and lacI genes had a positive effect on the biohydrogen production. The strain produced 22% more biohydrogen in a shorter time than the wild-type (WT) strain. A Box-Behnken experimental design was used to optimize pH, temperature and substrate concentration. The optimal initial conditions for biohydrogen production by WDHL strain were pH 7.5, 37 °C and 20 g/L of cheese whey. The specific production rate was improved from 3.29 mL H₂/optical density at 600 nm (OD_600nm) unit-h produced by WDHL under non-optimal conditions to 5.88 mL H₂/OD_600nm unit-h under optimal conditions. Using optimal initial conditions, galactose can be metabolized by WDHL strain. The maximum yield obtained was 2.74 mol H₂/mol lactose consumed, which is comparable with the yield reached in other hydrogen production processes with Clostridium sp. or mixed cultures.     

Fermentative hydrogen yields from different sugars by batch cultures of metabolically engineered Escherichia coli DJT135

Future sustainable production of biofuels will depend upon the ability to use complex substrates present in biomass if the use of simple sugars derived from food crops is to be avoided. Therefore, organisms capable of using a variety of fermentable carbon sources must be found or developed for processes that could produce hydrogen via fermentation. Here we have examined the ability of a metabolically engineered strain of Escherichia coli, DJT135, to produce hydrogen from glucose as well as various other carbon sources, including pentoses. The effects of pH, temperature and carbon source were investigated in batch experiments. Maximal hydrogen production from glucose was obtained at an initial pH of 6.5 and temperature of 35 °C. Kinetic growth studies showed that the μmax was 0.0495 h⁻¹ with a Ks of 0.0274 g L⁻¹ when glucose was the sole carbon source in M9 (1X) minimal medium. Among the many sugar and sugar derivatives tested, hydrogen yields were highest with fructose, sorbitol and d-glucose; 1.27, 1.46 and 1.51 mol H₂ mol⁻¹ substrate respectively.     

A pilot-scale study of biohydrogen production from distillery effluent using defined bacterial co-culture

We evaluated the feasibility of improving the scale of hydrogen (H₂) production from sugar cane distillery effluent using co-cultures of Citrobacter freundii 01, Enterobacter aerogenes E10 and Rhodopseudomonas palustris P2 at 100 m³ scale. The culture conditions at 100 ml and 2 L scales were optimized in minimal medium and we observed that the co-culture of the above three strains enhanced H₂ productivity significantly. Results at the 100 m³ scale revealed a maximum of 21.38 kg of H₂, corresponding to 10692.6 mol, which was obtained through batch method at 40 h from reducing sugar (3862.3 mol) as glucose. The average yield of H₂ was 2.76 mol mol⁻¹ glucose, and the rate of H₂ production was estimated as 0.53 kg/100 m³/h. Our results demonstrate the utility of distillery effluent as a source of clean alternative energy and provide insights into treatment for industrial exploitation.     

Fermentative hydrogen production by new marine Clostridium amygdalinum strain C9 isolated from offshore crude oil pipeline

The present study investigated hydrogen production potential of novel marine Clostridium amygdalinum strain C9 isolated from oil water mixtures. Batch fermentations were carried out to determine the optimal conditions for the maximum hydrogen production on xylan, xylose, arabinose and starch. Maximum hydrogen production was pH and substrate dependant. The strain C9 favored optimum pH 7.5 (40 mmol H₂/g xylan) from xylan, pH 7.5–8.5 from xylose (2.2–2.5 mol H₂/mol xylose), pH 8.5 from arabinose (1.78 mol H₂/mol arabinose) and pH 7.5 from starch (390 ml H₂/g starch). But the strain C9 exhibited mixed type fermentation was exhibited during xylose fermentation. NaCl is required for the growth and hydrogen production. Distribution of volatile fatty acids was initial pH dependant and substrate dependant. Optimum NaCl requirement for maximum hydrogen production is substrate dependant (10 g NaCl/L for xylose and arabinose, and 7.5 g NaCl/L for xylan and starch).     

Enzymatic saccharification and fermentation of paper and pulp industry effluent for biohydrogen production

Paper and pulp industry effluent was enzymatically hydrolysed using crude cellulase enzyme (0.8–2.2FPU/ml) obtained from Trichoderma reesei and from the hydrolysate biohydrogen was produced using Enterobacter aerogenes. The influence of temperature and incubation time on enzyme production was studied. The optimum temperature for the growth of T. reesei was found to be around 29 °C. The enzyme activity of 2.5 FPU/ml was found to produce about 22 g/l of total sugars consisting mainly of glucose, xylose and arabinose. Relevant kinetic parameters with respect to sugars production were estimated using two fraction model. The enzymatic hydrolysate was used for the biohydrogen production using E. aerogenes. The growth data obtained for E. aerogenes were fitted well with Monod and Logistic equations. The maximum hydrogen yield of 2.03 mol H₂/mol sugar and specific hydrogen production rate of 225 mmol of H₂/g cell/h were obtained with an initial concentration of 22 g/l of total sugars. The colour and COD of effluent was also decreased significantly during the production of hydrogen. The results showed that the paper and pulp industry effluent can be used as a substrate for biohydrogen production.     

Enhancement of biohydrogen producing using ultrasonication

Ultrasonication was evaluated as a pretreatment for biological hydrogen production from glucose in batch studies, in comparison with heat-shock pretreatment, acid pretreatment, and base pretreatment. The optimized sonication energy for hydrogen production using anaerobic digester sludge was 79 kJ/gTS. Sonication with temperature control (less than 30 °C) increased volumetric hydrogen production by 120% over the untreated sludge, and by 40% over the heat-shock and acid pretreated sludge, with a marginal (∼10%) increase in hydrogen production rate. Upon comparing the molar hydrogen yield in sonicated sludge with and without temperature control, the deleterious effect of heat on some hydrogen producers as reflected by a 30% decrease in yield to 1.03 mol H₂/mol glucose is evident. Sonication with temperature control affected a 45% increase in molar hydrogen yield to 1.55 mol H₂/mol glucose over heat-shock pretreatment at 70 °C for 30 min and acidification to pH 3.0 for 24 h at 4 °C. Sonication with temperature control produced a biomass yield of 0.13 g VSS/g COD, as compared to 0.24 g VSS/g COD for the untreated sludge. The hydrogen yield increased linearly with the molar acetate to butyrate ratio and decreased linearly with the biomass yield.     

Fermentative hydrogen production by diverse microflora

In this study, hydrogen production with activated sludge, a diverse bacterial source has been investigated and compared to microflora from anaerobic digester sludge, which is less diverse. Batch experiments were conducted at mesophilic (37 °C) and thermophilic (55 °C) temperatures. The hydrogen production yields with activated sludge at 37 °C and 55 °C were 0.56 and 1.32 mol H₂/mol glucose consumed, respectively. While with anaerobically digested sludge hydrogen yield was 2.18 mol H₂/mol glucose consumed at 37 °C and 1.25 mol H₂/mol glucose consumed at 55 °C. The results of repeated batch experiments for 615 h resulted in average yields of 1.21 ± 0.62 and 1.40 ± 0.16 mol H₂/mol glucose consumed for activated sludge and anaerobic sludge, respectively. The hydrogen production with activated sludge was not stable during the repeated batches and the fluctuation in hydrogen production was attributed to formation of lactic acid as the predominant metabolite in some batches. The presence of lactic acid bacteria in microflora was confirmed by PCR-DGGE.     

Pretreatment of sweet sorghum bagasse for hydrogen production by Caldicellulosiruptor saccharolyticus

Pretreatment of sweet sorghum bagasse, an energy crop residue, with NaOH for the production of fermentable substrates, was investigated. Optimal conditions for the alkaline pretreatment of sweet sorghum bagasse were realized at 10% NaOH (w/w dry matter). A delignification of 46% was then observed, and improved significantly the efficiency of enzymatic hydrolysis. Under hydrolysis conditions without pH control, up to 50% and 41% of the cellulose and hemicellulose contained in NaOH-pretreated sweet sorghum bagasse were converted by 24 h enzymatic hydrolysis to soluble monomeric sugars. The extreme thermophilic bacterium Caldicellulosiruptor saccharolyticus showed normal growth on hydrolysates of NaOH-pretreated biomass up to a sugar concentration of 20 g/L. Besides hydrogen, the main metabolic products detected in the fermentations were acetic and lactic acid. The maximal hydrogen yield observed in batch experiments under controlled conditions was 2.6 mol/mol C6 sugar. The maximal volumetric hydrogen production rate ranged from 10.2 to 10.6 mmol/(L h). At higher substrate concentrations the production of lactic acid increased at the expense of hydrogen production.